3.5x2.8 mm INFRARED EMITTING DIODE Part Number: AA3528F3C Features Description z Mechanically and spectrally matched to the phototransistor. F3 Made with Gallium Arsenide Infrared Emitting diodes. z Package : 1500pcs / reel. z Moisture sensitivity level : level 4. z RoHS compliant. Package Dimensions Notes: 1. All dimensions are in millimeters (inches). 2. Tolerance is ±0.25(0.01") unless otherwise noted. 3. Specifications are subject to change without notice. 4.The device has a single mounting surface. The device must be mounted according to the specifications. SPEC NO: DSAD1361 REV NO: V.4 DATE: SEP/30/2009 PAGE: 1 OF 5 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: Q.Q.Zhu ERP: 1201005542 Selection Guide Part No. AA3528F3C Dice Po (mW/sr) [2] @ 20mA *50mA Lens Type F3 (GaAs) WATER CLEAR Min. Typ. 1.6 3 *2.6 *8 Viewing Angle [1] 2θ1/2 120° Notes: 1. θ1/2 is the angle from optical centerline where the luminous intensity is 1/2 of the optical peak value. 2. * Luminous intensity with asterisk is measured at 50mA;Radiant Intensity/ luminous flux: +/-15%. Electrical / Optical Characteristics at TA=25°C Parameter P/N Symbol Typ. Max. Units Test Conditions Forward Voltage [1] F3 VF 1.2 1.6 V IF=20mA Reverse Current F3 IR 10 uA VR = 5V Capacitance F3 C 90 pF VF=0V;f=1MHz Peak Spectral Wavelength F3 λP 940 nm IF=20mA Spectral Bandwidth F3 Δλ1/2 50 nm IF=20mA Note: 1. Forward Voltage: +/-0.1V. Absolute Maximum Ratings at TA=25°C Parameter Symbol F3 Units Power dissipation PD 80 mW DC Forward Current IF 50 mA Peak Forward Current [1] iFS 1.2 A Reverse Voltage VR 5 V Operating Temperature TA -40 To +85 °C TSTG -40 To +85 °C Storage Temperature Note: 1. 1/100 Duty Cycle, 10μs Pulse Width. SPEC NO: DSAD1361 REV NO: V.4 DATE: SEP/30/2009 PAGE: 2 OF 5 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: Q.Q.Zhu ERP: 1201005542 AA3528F3C SPEC NO: DSAD1361 REV NO: V.4 DATE: SEP/30/2009 PAGE: 3 OF 5 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: Q.Q.Zhu ERP: 1201005542 AA3528F3C Reflow soldering is recommended and the soldering profile is shown below. Other soldering methods are not recommended as they might cause damage to the product. Recommended Soldering Pattern (Units : mm; Tolerance: ± 0.1) Tape Specifications (Units : mm) SPEC NO: DSAD1361 REV NO: V.4 DATE: SEP/30/2009 PAGE: 4 OF 5 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: Q.Q.Zhu ERP: 1201005542 PACKING & LABEL SPECIFICATIONS AA3528F3C SPEC NO: DSAD1361 REV NO: V.4 DATE: SEP/30/2009 PAGE: 5 OF 5 APPROVED: WYNEC CHECKED: Allen Liu DRAWN: Q.Q.Zhu ERP: 1201005542