RoHS GBL005 THRU GBL10 GBL005 SINGLE PHASE GLASS PASSIVATED BRIDGE RECTIFIERS THRU GBL10 FEATURES Plastic package has Underwriters Laboratory Flammability Classification 94 V-0 This series is UL listed under the Recognized Component Index, file number E54214 Glass passivated chip junctions Typical IR High case dielectric strength High surge current capability Ideal for printed circuit boards High temperature soldering guaranteed: 260 / 10 seconds at 5 lbs. (2.3kg) tension 0.825 (20.9) 0.815 (20.7) 0.125 (3.17) x 45 degrees Chamfer 0.421 (10.7) 0.411 (10.4) 0.080 (2.03) 0.060 (1.50) 0.095 (2.41) 0.080 (2.03) 0.098 (2.5) 0.075 (1.9) 0.050 (1.27) 0.040 (1.02) MECHANICAL DATA Case: Molded plastic body over passivated junctions Terminals: Plated leads solderable per MIL-STD-750 method 2026 Mounting position: Any Weight: 0.071 ounce, 2.0gram IC 0.040 (1.02) 0.030 (0.76) N C O 0.098 (2.5) 0.075 (1.9) 0.718 (18.2) 0.682 (17.3) Lead Depth 0.022 (0.56) 0.018 (0.46) 0.210 (5.3) 0.190 (4.8) 0.140 (3.56) 0.128 (3.25) 0.022 (0.56) 0.018 (0.46) Polarity shown on front side of case: positive lead by beveled corner R T O MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 25 ambient temperature unless otherwise specified SYMBOLS C E L VRRM Maximum Repetitive Peak Reverse Voltage VRMS Maximum RMS Voltage VDC Maximum DC Blocking Voltage TC = 50(Note Maximum Average Forward IF(AV) TA = 40(Note Output Rectified Current at Peak Forward Surge Current IFSM 8.3ms single half sine - wave superimposed on rated load (JEDEC method )TJ - 150 2 Rating for fusing (t <8.3ms) It Maximum Instantaneous Forward Voltage VF drop per leg at 4.0A Maximum DC Reverse Current at rate TA = 25 IR TA = 125 DC blocking voltage per leg CJ Typical Junction Capacitance per leg at 4.0V, 1MHz R Typical Thermal Resistance per leg (Note 1) R (Note 2) T Operating and Storage Temperature Range J, TSTG J E D T ,. L CaseType GBL Dimensions in inches and (millimeters) GBL 005 GBL 01 GBL 02 GBL 04 GBL 06 GBL 08 GBL 10 UNIT Volts Volts Volts E W Amps Amps A sec Volts A 2 22 (-55 TO +150) NOTES: 1. Unit mounted on 3.0*3.0*0.11" thick (7.5*7.5*0.3cm) Al. plate. 2. Unit mounted on P.C.B.at 0.375" (9..5mm) lead length and 0.5*0.5" (12*12mm) sopper pads MIC INVESTMENTS (CHINA) COMPANY LIMITED WEJ ELECTRONIC CO. Http:// www.wej.cn E-mail:[email protected] pF /W RoHS 5.0 60 Hz RESISTIVE OR INDUCTIVE LOAD 4.0 HEAT-SINK MOUNTING, 3.0 x 3.0 x 0.11” THK (7.5 x 7.5 x 0.3cm) AL. PLATE 3.0 2.0 1.0 0 P.C.B. MOUNTING 0.47 x 0.47” (12 x 12mm) COPPER PADS 0.375” (9.5mm) LEAD LENGTH 60Hz RESISTIVE OR INDUCTIVE LOAD 0 50 TJ = TJ max. SINGLE SINE-WAVE (JEDEC Method) 100 50 1.0 CYCLE 0 R T C E L 0.01 0.4 0.6 E 0.8 1.0 1.2 1.4 O 100 INSTANTANEOUS REVERSE CURRENT, MICROAMPERES INSTANTANEOUS FORWARD CURRENT, AMPERES 500 TJ=25°C PULSE WIDTH=300µs 1% DUTY CYCLE 0.1 TA=25°C 0.01 0 100 50 - 400V 600 - 1000V 10 40 60 80 100 100 100 REVERSE VOLTAGE, VOLTS WEJ ELECTRONIC CO. 20 PERCENT OF RATED PEAK REVERSE VOLTAGE, % TRANSIENT THERMAL IMPEDANCE, °C/W JUNCTION CAPACITANCE, pF TJ=25°C f=1.0 MHz Vsig=50mVp-p 1 TA=125°C FIG. 6 - TYPICAL TRANSIENT THERMAL IMPEDANCE PER LEG 1,000 10 0.1 50 - 400V 600 - 1000V 1 1.6 FIG. 5 - TYPICAL JUNCTION CAPACITANCE PER LEG W 100 FIG. 4 - TYPICAL REVERSE LEAKAGE CHARACTERISTICS PER LEG 10 INSTANTANEOUS FORWARD VOLTAGE, VOLTS J E IC N 100 0.1 ,. L O NUMBER OF CYCLES AT 60 Hz FIG. 3 - TYPICAL FORWARD VOLTAGE CHARACTERISTICS PER LEG 1 C 10 1 AMBIENT TEMPERATURE, °C 10 D T 150 150 100 GBL10 FIG. 2 - MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT PER LEG FIG. 1 - DERATING CURVES OUTPUT RECTIFIED CURRENT PEAK FORWARD SURGE CURRENT, AMPERES AVERAGE FORWARD OUTPUT CURRENT, AMPERES RATINGS AND CHARACTERISTICS CURVES GBL005 THRU GBL10 GBL005 THRU Http:// www.wej.cn 10 1 0.1 0.01 0.1 10 1 t, HEATING TIME, sec. E-mail:[email protected] 100