GBL005 THRU GBL10 GLASS PASSIVATED SINGLE-PHASE BRIDGE RECTIFIER Reverse Voltage - 50 to 1000 Volts Forward Current - 4.0 Amperes FEATURES Case Type GBL 0.825 (20.9) 0.815 (20.7) 0.125 (3.17) x 45 degrees Chamfer 0.421 (10.7) 0.411 (10.4) 0.080 (2.03) 0.060 (1.50) 0.098 (2.5) 0.075 (1.9) 0.095 (2.41) 0.080 (2.03) 0.718 (18.2) 0.682 (17.3) 0.098 (2.5) 0.075 (1.9) Lead Depth 0.022 (0.56) 0.050 (1.27) 0.018 (0.46) 0.040 (1.02) 0.210 (5.3) 0.190 (4.8) ♦ Plastic package has Underwriters Laboratory Flammability Classification 94V-0 ♦ This series is UL listed under the Recognized Component Index, file number E54214 ♦ Glass passivated chip junctions ♦ High case dielectric strength ♦ Typical IR less than 0.1µA ♦ High surge current capability ♦ Ideal for printed circuit boards ♦ High temperature soldering guaranteed: 260°C/10 seconds, 0.375" (9.5mm) lead length, 5 lbs. (2.3kg) tension 0.040 (1.02) 0.030 (0.76) 0.140 (3.56) 0.128 (3.25) 0.022 (0.56) 0.018 (0.46) Polarity shown on front side of case: positive lead by beveled corner Dimensions in inches and (millimeters) MECHANICAL DATA Case: Molded plastic body over passivated junctions Terminals: Plated leads solderable per MIL-STD-750, Method 2026 Mounting Position: Any Weight: 0.071 ounce, 2.0 grams MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 25°C ambient temperature unless otherwise specified. SYMBOLS GBL 005 GBL 01 GBL 02 GBL 04 GBL 06 GBL 08 Maximum repetitive peak reverse voltage VRRM 50 100 200 400 600 800 Maximum RMS voltage VRMS 35 70 140 280 420 560 700 VDC 50 100 200 400 600 800 1000 Volts Maximum DC blocking voltage GBL 10 UNITS 1000 Volts Volts TC=50°C (NOTE 1) TA=40°C (NOTE 2) I(AV) 4.0 3.0 Amps Peak forward surge current, single half sine-wave superimposed on rated load (JEDEC Method) TJ=150°C IFSM 150.0 Amps Rating for fusing (t<8.3ms) I2t 93.0 A2sec Maximum instantaneous forward drop per leg at 4.0 Amperes VF 1.1 Volts IR 5.0 500.0 µA Maximum average forward rectified output current at Maximum DC reverse current at rated DC blocking voltage per leg TA=25°C TA=125°C Typical junction capacitance per leg (NOTE 3) CJ Typical thermal resistance per leg (NOTE 1) RΘJA RΘJL 22.0 3.5 °C/W TJ, TSTG -55 to +150 °C (NOTE 2) Operating junction storage and temperature range NOTES: (1) Unit mounted on 3.0 x 3.0 x 0.11" thick (7.5 x 7.5 x 0.3cm) Al. plate (2) Unit mounted on P.C.B. at 0.375" (9.5mm) lead length and 0.5 x 0.5" (12 x12mm) copper pads (3) Measured at 1.0 MHz and applied reverse voltage of 4.0 Volts 4/98 95.0 40.0 pF FIG. 2 - MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT PER LEG FIG. 1 - DERATING CURVES OUTPUT RECTIFIED CURRENT 5.0 PEAK FORWARD SURGE CURRENT, AMPERES AVERAGE FORWARD OUTPUT CURRENT, AMPERES RATINGS AND CHARACTERISTICS CURVES GBL005 THRU GBL10 60 Hz RESISTIVE OR INDUCTIVE LOAD 4.0 HEAT-SINK MOUNTING, 3.0 x 3.0 x 0.11” THK (7.5 x 7.5 x 0.3cm) AL. PLATE 3.0 2.0 1.0 0 P.C.B. MOUNTING 0.47 x 0.47” (12 x 12mm) COPPER PADS 0.375” (9.5mm) LEAD LENGTH 60Hz RESISTIVE OR INDUCTIVE LOAD 0 50 150 TJ = TJ max. SINGLE SINE-WAVE (JEDEC Method) 100 50 1.0 CYCLE 0 150 100 NUMBER OF CYCLES AT 60 Hz FIG. 4 - TYPICAL REVERSE LEAKAGE CHARACTERISTICS PER LEG FIG. 3 - TYPICAL FORWARD VOLTAGE CHARACTERISTICS PER LEG 500 10 TJ=25°C PULSE WIDTH=300µs 1% DUTY CYCLE 1 0.1 50 - 400V 600 - 1000V 100 INSTANTANEOUS REVERSE CURRENT, MICROAMPERES INSTANTANEOUS FORWARD CURRENT, AMPERES 100 TA=125°C 10 1 0.1 TA=25°C 0.01 0.4 0.6 0.8 1.0 1.2 1.4 0.01 0 1.6 TRANSIENT THERMAL IMPEDANCE, °C/W 1,000 TJ=25°C f=1.0 MHz Vsig=50mVp-p 100 50 - 400V 600 - 1000V 1 10 REVERSE VOLTAGE, VOLTS 40 60 80 100 FIG. 6 - TYPICAL TRANSIENT THERMAL IMPEDANCE PER LEG FIG. 5 - TYPICAL JUNCTION CAPACITANCE PER LEG 10 0.1 20 PERCENT OF RATED PEAK REVERSE VOLTAGE, % INSTANTANEOUS FORWARD VOLTAGE, VOLTS JUNCTION CAPACITANCE, pF 100 10 1 AMBIENT TEMPERATURE, °C 100 100 10 1 0.1 0.01 0.1 10 1 t, HEATING TIME, sec. 100