KOA SPEER ELECTRONICS, INC. SS-217 R4 AHA 8/16/12 Chip Networks Resistors Type CNB & CND Series CERTIFIED CERTIFIED 1. Features ■ Concave or convex termnations Manufactured to type RK73 standards ■ Four or eight bussed resistor elements included in one array ■ Less board space than individual chips ■ Products with lead-free terminations meet EU RoHS requirements. EU RoHS regulation is not intended for Pb-glass contained in electrode, resistor element and glass. ■ 2. Dimensions Size Code Dimensions inches (mm) P2 a (top) W t P1 a (bot.) b (ref.) c (ref.) d 2B9Z .252±.008 (6.4±0.2) .126±.008 (3.2±0.2) .024±.004 (0.6±0.1) .051±.004 (1.3±0.1) .026±.004 (0.65±0.1) .033 (0.85) .024±.004 (0.6±0.1) .006 (0.15) .018 (0.45) .024±.006 (0.6±0.15) 2E5Z .126±.008 (3.2±0.2) .098±.008 (2.5±0.2) .024±.004 (0.6±0.1) .039±.004 (1.0±0.1) .020±.004 (0.50±0.1) .026 (0.65) .022±.004 (0.55±0.1) .006 (0.15) .012 (0.3) .020±.006 (0.5±0.15) Size Code L L W C d Dimensions inches (mm) t a (top) e a2 a (bot.) b p .126±.004 (3.2±0.1) .063±.004 (1.6±0.1) .012±.008 (0.3±0.2) .012±.004 (0.3±0.1) — .020±.004 (0.5±0.1) .016±.004 (0.4±0.1) — .012 (0.3) — .025 (0.64) .126±.006 (3.2±0.15) .063±.008 (1.6±0.2) .012±.008 (0.3±0.2) .010±.004 (0.25±0.1) — .020±.004 (0.5±0.1) .016±.004 (0.4±0.1) .022±.004 (0.55±0.1) .012±.008 (0.3±0.2) — .014±.004 (0.35±0.1) .014±.004 (0.35±0.1) .016±.006 (0.4±0.15) .022±.004 (0.55±0.1) .013±.006 (0.33±0.15) — .012±.004 (0.3±0.1) .008±.004 (0.2±0.1) .157±.008 (4.0±0.2) .083±.008 (2.1±0.2) .010±.008 (0.25±0.2) .016±.008 (0.4±0.2) .020±.008 (0.5±0.2) .024±.004 (0.6±0.1) .020±.008 (0.5±0.2) — .016±.006 (0.4±0.15) .006±.004 (0.15±0.1) .031 (0.8) .252±.008 (6.4±0.2) .122±.008 (3.1±0.2) .014±.006 (0.35±0.15) .022±.006 (0.55±0.15) — .024±.004 (0.6±0.1) .024±.004 (0.6±0.1) — .024±.006 (0.6±0.15) .006±.004 (0.15±0.1) 0.05 (1.27) Figure No. 1J10VK 2 1J10K 2 1J10Y 1 2A10Y 2B10V 3 2B10 CNB Figure 1 L P1 a b Inner Electrode W c t Electrode p b W t d Protective Coating L a P2 Figure 2 d Protective Coating Resistive Film Electrode Ceramic Substrate Resistive Film Ceramic Substrate C e a L Figure 3 p a2 W C t d Protective Coating Inner Electrode Electrode Resistive Film Ceramic Substrate Inner Electrode b L a p b W t d Protective Coating Electrode C Resistive Film Ceramic Substrate Convex Concave .025 (0.64) Inner Electrode Concave PAGE 1 OF 4 Bolivar Drive ■ P.O. Box 547 ■ Bradford, PA 16701 ■ USA ■ 814-362-5536 ■ Fax 814-362-8883 ■ www.koaspeer.com Specifications given herein may be changed at any time without prior notice. Please confirm technical specifications before you order and/or use. KOA SPEER ELECTRONICS, INC. SS-217 R4 3. Type Designation The type designation shall be the following form: CNB 2B 9 Z T TE 103 J Type Size Elements Circuit Symbol Termination Material Packaging Nominal Resistance Tolerance CNB CND 1J 2A 2B 2E 5 9 10 T: Sn TD: 7" Paper Taping TE: 7" Embossed Taping 2 significant figures + 1 multiplier J: ±5% V: Reverse common electrode Y: Side electrode type Nil: Standard Z: for CNB (Other termination styles may be available, please contact factory for options) 4. Circuit Construction 9 8 R R 7 R 6 R R 1 C R 2 R R 3 4 CNB2B9Z R 5 R R R R R R CND1J10Y, CND2A10Y 10 9 8 7 6 R R R R R R R R R R R 1 1 2 3 CNB2E5Z 2 3 4 CND2B10V 9 8 7 10 R 1 R R CND1J10K 9 8 7 10 5 4 5 R R R R R R 6 9 10 CND2B10 8 7 R R R R R R 6 R CND1J10VK 9 8 7 10 R R R R R R R 6 6 5 2 103 3 5 4 1 103 2 3 R 4 R 5 103 1 2 3 5 4 103 1 2 3 R 4 5 103 5. Standard Applications Part Designation CNB2B9Z CNB2E5Z CND1J10VK CND1J10K CND1J10Y CND2A10Y CND2B10V CND2B10 Power Rating @ 70°C (Per Element) T.C.R. (ppm/°C) Max. Resistance Range E-3*, E-12** Resistance Tolerance Absolute Maximum Working Voltage Maximum Overload Voltage (5 Secs. Max.) Operating Temperature Range 1/16W (.063W) ±200 1KΩ - 470KΩ J: ±5% 50V 100V -55°C to +125°C 25V 50V .031 47Ω - 39kΩ .05 22Ω - 39KΩ ±200 .063 -55°C to +125°C J: ±5% 100Ω - 100KΩ 50V 100V * E-3 significant figures (per decade) are 1.0, 2.2 and 4.7. ** E-12 CND only PAGE 2 OF 4 Bolivar Drive ■ P.O. Box 547 ■ Bradford, PA 16701 ■ USA ■ 814-362-5536 ■ Fax 814-362-8883 ■ www.koaspeer.com Specifications given herein may be changed at any time without prior notice. Please confirm technical specifications before you order and/or use. KOA SPEER ELECTRONICS, INC. SS-217 R4 6. Environmental Applications 6-2 Voltage Rating For temperature in excess of 70°C, the load shall be derated in accordance with the following figure. Resistors shall have a rated direct-current (DC) continuous working voltage or approximate sine-wave root-mean-square (R.M.S.) continuous working voltage at commercial-line frequency and wave-form corresponding the power rating as determined from the following formula: Derating Curve 100 Where: E: Rated Voltage (V) % Rated Power 80 E= √ P • R P: Power Rating (W) R: Nominal Resistance (Ω) 60 However, if the rated voltage thus obtained surpasses the specified maximum working voltage, it shall be considered the rated voltage. 40 20 0 0 20 40 60 80 100 120 140 70 125 Ambient Temperature (°C) 160 7. Performance CNB Parameter Resistance T.C.R. Overload (Short time) Resistance to Solder Heat Rapid Change of Temperature Moisture Resistance Endurance at 70°C Low Temperature Operation High Temperature Exposure Requirement ∆ R ±% Limit Typical Within regulated — tolerance Within specified — T.C.R. ±2.0% ±0.5% ±1.0% ±0.25% ±1.0% ±1.0% ±5.0% ±1.0% ±5.0% ±0.5% ±1.0% ±0.2% ±1.0% ±0.2% Test Method 25°C +25°C/-55°C, +25°C/+125°C Rated voltage x 2.5 for 5 seconds 260°C ± 5°C, 10 seconds ± 1 second -55°C (30 minutes), +125°C (30 minutes), 5 cycles 40°C ± 2°C, 90 - 95% RH, 1000 hours, 1.5 hr ON, 0.5 hr OFF cycle 70°C ± 2°C, 1000 hours, 1.5 hr ON, 0.5 hr OFF cycle -55°C, 1 hour +125°C, 1000 hours CND Parameter Resistance T.C.R. Overload (Short time) Resistance to Solder Heat Rapid Change of Temperature Moisture Resistance Endurance at 70°C Low Temperature Operation High Temperature Exposure Requirement ∆ R ±1% Limit Typical Within specified — tolerance Within specified — T.C.R. ±2.0% ±0.5% ±1.0% ±0.25% ±1.0% ±0.25% ±5.0% ±1.0% ±5.0% ±1.0% ±1.0% ±0.2% ±1.0% ±0.2% Test Method 25°C +25°C/-55°C, +25°C/+125°C Rated voltage x 2.5 for 5 seconds 260°C ± 5°C, 10 seconds ± 1 second -55°C (30 minutes), +125°C (30 minutes), 5 cycles 40°C ± 2°C, 90 - 95% RH, 1000 hours, 1.5 hr ON, 0.5 hr OFF cycle 70°C ± 2°C, 1000 hours, 1.5 hr ON, 0.5 hr OFF cycle -55°C, 1 hour +125°C, 1000 hours PAGE 3 OF 4 Bolivar Drive ■ P.O. Box 547 ■ Bradford, PA 16701 ■ USA ■ 814-362-5536 ■ Fax 814-362-8883 ■ www.koaspeer.com Specifications given herein may be changed at any time without prior notice. Please confirm technical specifications before you order and/or use. KOA SPEER ELECTRONICS, INC. SS-217 R4 8. Body Color and Marking Body Color: Black Marking Color: White 3-digit numbers The first and the second numbers show 2 effective numbers, the third number shows a multiple of 10. Example: 103 10,000Ω 10kΩ 472 4,700Ω 4.7kΩ 1 0 3 103 Nominal resistance at 3-digit numbers Tape material and quantity per reel Tape material Tape width Quantity/Reel (pcs.) Embossed .472 in. (12 mm) 4,000 1.75±0.1 9.1 Taping Dimension (Embossed) 1.5 +0.1 -0 Carrier Tape A B W 9. Taping P1 (TP) T1 P1 T1 T1 2.0 4.0±0.1 Direction of feed (Notes) Dotted lines are applicable to only "TP" and "TB." Component Size (mm) Type CND CNB 2B10 1J10 2A10 2B5Z 2E9Z L W T 6.40 3.20 4.00 3.2 6.40 3.1 1.6 2.1 2.5 3.2 0.6 0.55 0.6 0.6 10. Reel (Polystyrene Reel) Reel Taping (mm) Carrier Tape Quantity/ Reel (Pieces) A B W P1 T1 Reel Size TE TD TE TE TE 4000 5000 4000 4000 4000 6.6±0.2 3.5±0.1 4.45±0.2 3.5±0.2 6.7±0.2 3.4±0.2 2.0±0.1 2.5±0.2 3.0±0.2 3.5±0.2 12.0±0.1 8.0±0.2 12.0±0.1 8.0±0.2 12.0±0.1 4.0±0.1 4.0±0.1 4.0±0.1 4.0±0.1 4.0±0.1 1±0.15 0.75+0.2/-0 1±0.15 1±0.15 1±0.15 178 178 178 178 178 (mm) øa Central hole ø13 e Type All ød (mm) e (mm) 21 2 ød (Notes) Reel holes, shapes and design are examples 11. Reel Marking Lot Number The reel must be marked as follows: (1) Type designation (2) Nominal resistance (3) Quantity (4) Production lot number (5) Manufacturer’s name (6) Customer’s code number (7) Order number Lot number (8 digits) 23 Production year, month 12 Date 8 Factory 001 Continuous number 8 KT & T factory 11~22 January 2011 ~ December 2011 23~34 January 2012 ~ December 2012 PAGE 4 OF 4 Bolivar Drive ■ P.O. Box 547 ■ Bradford, PA 16701 ■ USA ■ 814-362-5536 ■ Fax 814-362-8883 ■ www.koaspeer.com Specifications given herein may be changed at any time without prior notice. Please confirm technical specifications before you order and/or use.