PAA110L

PAA110L
Dual Single-Pole
OptoMOS® Relays
INTEGRATED CIRCUITS DIVISION
Parameters
Load Voltage
Load Current
On-Resistance (max)
Ratings
400
150
25
Units
VP
mArms / mADC

Features
• Current Limiting
• 3750Vrms Input/Output Isolation
• Low Drive Power Requirements (TTL/CMOS
Compatible)
• 100% Solid State
• Arc-Free With No Snubbing Circuits
• No EMI/RFI Generation
• Small 8-Pin DIP Package
• Machine Insertable, Wave Solderable
• Surface Mount and Tape Reel Version Available.
Applications
• Telecommunications
• Telecom Switching
• Tip/Ring Circuits
• Modem Switching (Laptop, Notebook, Pocket
Size)
• Hook Switch
• Dial Pulsing
• Ground Start
• Ringing Injection
• Instrumentation
• Multiplexers
• Data Acquisition
• Electronic Switching
• I/O Subsystems
• Meters (Watt-Hour, Water, Gas)
• Medical Equipment-Patient/Equipment Isolation
• Security
• Aerospace
• Industrial Controls
Description
PAA110L is a dual 400V, 150mA, 25 1-Form-A
(normally open) relay. This performance leader
provides high peak load voltage handling capability
and improved peak load current handling. Integrated
current-limiting circuitry limits current to 280mA at
room temperature.
Approvals
• UL Recognized Component: File # E76270
• CSA Certified Component: File # 1175739
• EN/IEC 60950-1 Compliant
Ordering Information
Part #
PAA110L
PAA110PL
PAA110PLTR
PAA110LS
PAA110LSTR
Description
8-Pin DIP (50/Tube)
8-Pin Flatpack (50/Tube)
8-Pin Flatpack (1000/Reel)
8-Pin Surface Mount (50/Tube)
8-Pin Surface Mount (1000/Reel)
Pin Configuration
AC/DC Configuration
+ Control - Switch #1
– Control - Switch #1
+ Control - Switch #2
– Control - Switch #2
1
8
2
7
3
6
4
5
Load - Switch #1
Load - Switch #1
Load - Switch #2
Load - Switch #2
Switching Characteristics of
Normally Open (Form A) Devices
Form-A
IF
90%
10%
ILOAD
ton
Pb
DS-PAA110L-R06
toff
e3
www.ixysic.com
1
INTEGRATED CIRCUITS DIVISION
PAA110L
Absolute Maximum Ratings @25ºC
Parameter
Blocking Voltage
Reverse Input Voltage
Input Control Current
Peak (10ms)
Input Power Dissipation 1
Total Power Dissipation 2
Isolation Voltage Input to Output
Operational Temperature
Storage Temperature
1
Derate linearly 1.33 mW / ºC
2
Derate linearly 6.67 mW / ºC
Ratings
400
5
50
1
150
800
3750
-40 to +85
-40 to +125
Units
VP
V
mA
A
mW
mW
Vrms
°C
°C
Absolute Maximum Ratings are stress ratings. Stresses in
excess of these ratings can cause permanent damage to
the device. Functional operation of the device at conditions
beyond those indicated in the operational sections of this
data sheet is not implied.
Electrical Characteristics @25ºC
Parameter
Output Characteristics
Load Current, Continuous
On-Resistance
Off-State Leakage Current
Switching Speeds
Turn-On
Turn-Off
Output Capacitance
Load Current Limiting
Capacitance Input to Output
Input Characteristics
Input Control Current to Activate
Input Control Current to Deactivate
Input Voltage Drop
Reverse Input Current
Common Characteristics
Input to Output Capacitance
Conditions
Symbol
Min
Typ
Max
Units
IL=150mA
VL=400V
IL
RON
ILEAK
-
18
-
150
25
1
mArms / mADC

A
50V; f=1MHz
-
ton
toff
COUT
ICL
-
190
-
0.3
0.058
25
235
3
1
0.5
280
-
pF
mArms / mADC
pF
IL=150mA
IF=5mA
VR=5V
IF
IF
VF
IR
0.4
0.9
-
1.2
-
5
1.4
10
mA
mA
V
A
-
CI/O
-
3
-
pF
IF=5mA, VL=10V
ms
*NOTE: If both poles operate simultaneously load current must be derated in order not to exceed the package power dissipation value.
2
www.ixysic.com
R06
INTEGRATED CIRCUITS DIVISION
PAA110L
PERFORMANCE DATA @25ºC (Unless Otherwise Noted)*
25
20
15
10
5
1.17
25
1.19
1.21
1.23
15
10
5
20
15
10
5
0
0.15
1.25
0.21
0.27
0.33
0.39
0.045
0.45
0.052
0.059
0.066
0.073
LED Forward Voltage Drop (V)
Turn-On Time (ms)
Turn-Off Time (ms)
Typical IF for Switch Operation
(N=50, IL=150mADC)
Typical IF for Switch Dropout
(N=50)
Typical On-Resistance Distribution
(N=50, IF=5mA, IL=150mADC)
25
20
Device Count (N)
Device Count (N)
20
0
0
Typical Turn-Off Time
(N=50, IF=5mA, IL=150mADC)
25
Device Count (N)
Device Count (N)
Device Count (N)
30
25
Typical Turn-On Time
(N=50, IF=5mA, IL=150mADC)
15
10
5
35
30
20
Device Count (N)
35
Typical LED Forward Voltage Drop
(N=50, IF=5mA)
15
10
5
1.25
1.55
1.85
2.15
2.45
20
15
10
5
0
0
25
0
0.95
2.75
1.25
1.55
1.85
2.15
2.45
17.5
18.5
LED Current (mA)
LED Current (mA)
19.5
20.5
21.5
22.5
On-Resistance (:)
Typical Blocking Voltage Distribution
(N=50)
35
Device Count (N)
30
25
20
15
10
5
0
448
456
464
472
480
488
Blocking Voltage (VP)
Typical Turn-On Time
vs. LED Forward Current
(IL=150mADC)
0.30
1.6
1.4
I F = 50mA
I F = 30mA
I F = 20mA
I F = 10mA
I F = 5mA
1.2
1.0
0.06
0.25
0.20
0.15
0.10
0.05
-40
-20
0
20
40
60
Temperature (ºC)
80
100
120
0.05
0.04
0.03
0.02
0.01
0
0.8
Typical Turn-Off Time
vs. LED Forward Current
(IL=150mADC)
0.07
Turn-Off Time (ms)
1.8
Turn-On Time (ms)
LED Forward Voltage Drop (V)
Typical LED Forward Voltage Drop
vs. Temperature
0
0
5
10
15
20
25
30
35
Forward Current (mA)
40
45
50
0
5
10
15
20
25
30
35
40
45
50
Forward Current (mA)
*The Performance data shown in the graphs above is typical of device performance. For guaranteed parameters not indicated in the written specifications, please
contact our application department.
R06
www.ixysic.com
3
INTEGRATED CIRCUITS DIVISION
PAA110L
PERFORMANCE DATA @25ºC (Unless Otherwise Noted)*
1.25
Turn-Off Time (ms)
I F =5mA
1.00
I F =10mA
0.75
I F =20mA
0.50
0.25
0
-40
4.0
-20
0
20
40
60
80
0.10
0.09
0.08
0.07
0.06
0.05
0.04
0.03
0.02
0.01
0
100
10
0
20
40
60
80
-40
100
-20
0
20
40
60
Temperature (ºC)
Temperature (ºC)
Typical IF for Switch Operation
vs. Temperature
(IL=150mADC)
Typical IF for Switch Dropout
vs. Temperature
(IL=150mADC)
Typical Load Current
vs. Load Voltage
(IF=5mA)
4.0
150
3.0
2.5
2.0
1.5
1.0
Load Current (mA)
LED Current (mA)
LED Current (mA)
15
Temperature (ºC)
0.5
3.0
2.5
2.0
1.5
1.0
-20
0
20
40
60
80
50
0
-50
-40
-20
0
20
40
60
80
100
0
0.5 1.0 1.5 2.0 2.5
Temperature (ºC)
Temperature (ºC)
Load Voltage (V)
Maximum Load Current
vs. Temperature
Typical Blocking Voltage
vs. Temperature
Typical Leakage vs. Temperature
Measured Across Pins 5&6 or 7&8
Blocking Voltage (VP)
250
200
150
I F =20mA
I F =10mA
I F =5mA
100
50
490
0.035
485
0.030
480
475
470
465
460
455
0
20
40
60
80
100
120
0.025
0.020
0.015
0.010
0.005
450
445
0
-20
100
100
-150
-2.5 -2.0 -1.5 -1.0 -0.5
0
100
80
-100
0.5
0
Load Current (mA)
20
0
-20
3.5
-40
25
5
-40
3.5
-40
Typical On-Resistance
vs. Temperature
(IL=150mADC, IF=5mA)
30
Leakage (PA)
Turn-On Time (ms)
1.50
Typical Turn-Off Time
vs. Temperature
(IL=150mADC, IF=5mA)
On-Resistance (:)
Typical Turn-On Time
vs. Temperature
(IL=150mADC)
-40
-20
0
Temperature (ºC)
20
40
60
80
100
0
-40
-20
0
20
40
60
80
100
Temperature (ºC)
Temperature (ºC)
Typical Current Limiting
vs. Temperature
(IF=5mA)
350
Current (mA)
300
250
200
150
100
50
0
-40
-20
0
20
40
60
80
100
Temperature (ºC)
*The Performance data shown in the graphs above is typical of device performance. For guaranteed parameters not indicated in the written specifications, please
contact our application department.
4
www.ixysic.com
R06
INTEGRATED CIRCUITS DIVISION
PAA110L
Manufacturing Information
Moisture Sensitivity
All plastic encapsulated semiconductor packages are susceptible to moisture ingression. IXYS Integrated
Circuits Division classified all of its plastic encapsulated devices for moisture sensitivity according to
the latest version of the joint industry standard, IPC/JEDEC J-STD-020, in force at the time of product
evaluation. We test all of our products to the maximum conditions set forth in the standard, and guarantee proper
operation of our devices when handled according to the limitations and information in that standard as well as to any
limitations set forth in the information or standards referenced below.
Failure to adhere to the warnings or limitations as established by the listed specifications could result in reduced
product performance, reduction of operable life, and/or reduction of overall reliability.
This product carries a Moisture Sensitivity Level (MSL) rating as shown below, and should be handled according
to the requirements of the latest version of the joint industry standard IPC/JEDEC J-STD-033.
Device
Moisture Sensitivity Level (MSL) Rating
PAA110L / PAA110PL / PAA110LS
MSL 1
ESD Sensitivity
This product is ESD Sensitive, and should be handled according to the industry standard JESD-625.
Reflow Profile
This product has a maximum body temperature and time rating as shown below. All other guidelines of J-STD-020
must be observed.
Device
Maximum Temperature x Time
PAA110L / PAA110LS
250ºC for 30 seconds
PAA110PL
260ºC for 30 seconds
Board Wash
IXYS Integrated Circuits Division recommends the use of no-clean flux formulations. However, board washing to
remove flux residue is acceptable. Since IXYS Integrated Circuits Division employs the use of silicone coating as
an optical waveguide in many of its optically isolated products, the use of a short drying bake could be necessary
if a wash is used after solder reflow processes. Chlorine- or Fluorine-based solvents or fluxes should not be used.
Cleaning methods that employ ultrasonic energy should not be used.
Pb
R06
e3
www.ixysic.com
5
INTEGRATED CIRCUITS DIVISION
PAA110L
Mechanical Dimensions
PAA110L
2.540 ± 0.127
(0.100 ± 0.005)
9.652 ± 0.381
(0.380 ± 0.015)
8-0.800 DIA.
(8-0.031 DIA.)
2.540 ± 0.127
(0.100 ± 0.005)
9.144 ± 0.508
(0.360 ± 0.020)
6.350 ± 0.127
(0.250 ± 0.005)
Pin 1
PCB Hole Pattern
7.620 ± 0.254
(0.300 ± 0.010)
6.350 ± 0.127
(0.250 ± 0.005)
3.302 ± 0.051
(0.130 ± 0.002)
0.457 ± 0.076
(0.018 ± 0.003)
7.620 ± 0.127
(0.300 ± 0.005)
7.239 TYP.
(0.285)
4.064 TYP
(0.160)
7.620 ± 0.127
(0.300 ± 0.005)
0.254 ± 0.0127
(0.010 ± 0.0005)
Dimensions
mm
(inches)
0.813 ± 0.102
(0.032 ± 0.004)
PAA110PL
0 MIN / 0.102 MAX
(0 MIN / 0.004 MAX)
2.540 ± 0.127
(0.100 ± 0.005)
6.350 ± 0.127
(0.250 ± 0.005)
9.398 ± 0.127
(0.370 ± 0.005)
Pin 1
9.652 ± 0.381
(0.380 ± 0.015)
7.620 ± 0.254
(0.300 ± 0.010)
2.286 MAX.
(0.090 MAX.)
PCB Land Pattern
2.54
(0.10)
0.635 ± 0.127
(0.025 ± 0.005)
8.70
(0.3425)
1.55
(0.0610)
0.203 ± 0.013
(0.008 ± 0.0005)
0.65
(0.0255)
2.159 ± 0.025
(0.085 ± 0.001)
0.457 ± 0.076
(0.018 ± 0.003)
0.864 ± 0.120
(0.034 ± 0.004)
Dimensions
mm
(inches)
PAA110LS
9.652 ± 0.381
(0.380 ± 0.015)
2.540 ± 0.127
(0.100 ± 0.005)
6.350 ± 0.127
(0.250 ± 0.005)
Pin 1
0.635 ± 0.127
(0.025 ± 0.005)
3.302 ± 0.051
(0.130 ± 0.002)
9.525 ± 0.254
(0.375 ± 0.010)
0.457 ± 0.076
(0.018 ± 0.003)
PCB Land Pattern
2.54
(0.10)
8.90
(0.3503)
1.65
(0.0649)
7.620 ± 0.254
(0.300 ± 0.010)
0.254 ± 0.0127
(0.010 ± 0.0005)
0.65
(0.0255)
4.445 ± 0.127
(0.175 ± 0.005)
Dimensions
mm
(inches)
0.813 ± 0.102
(0.032 ± 0.004)
6
www.ixysic.com
R06
INTEGRATED CIRCUITS DIVISION
PAA110L
PAA110PLTR Tape & Reel
2.00
(0.079)
330.2 DIA.
(13.00 DIA.)
Top Cover
Tape Thickness
0.102 MAX.
(0.004 MAX.)
Embossment
W = 16.00
(0.63)
7.50
(0.295)
Bo = 10.30
(0.406)
K0 = 2.70
(0.106)
K1 = 2.00
(0.079)
Embossed Carrier
4.00
(0.157)
Ao = 10.30
(0.406)
P = 12.00
(0.472)
User Direction of Feed
Dimensions
mm
(inches)
NOTES:
1. All dimensions carry tolerances of EIA Standard 481-2
2. The tape complies with all “Notes” for constant dimensions listed on page 5 of EIA-481-2
PAA110LSTR Tape & Reel
330.2 DIA.
(13.00 DIA.)
Top Cover
Tape Thickness
0.102 MAX.
(0.004 MAX.)
K0 =4.90
(0.193)
K1 =4.20
(0.165)
Embossed Carrier
Embossment
W=16.00
(0.63)
Bo=10.30
(0.406)
Ao=10.30
(0.406)
P=12.00
(0.472)
User Direction of Feed
Dimensions
mm
(inches)
NOTES:
1. Dimensions carry tolerances of EIA Standard 481-2
2. Tape complies with all “Notes” for constant dimensions listed on page 5 of EIA-481-2
For additional information please visit our website at: www.ixysic.com
IXYS Integrated Circuits Division makes no representations or warranties with respect to the accuracy or completeness of the contents of this publication and reserves the right to make
changes to specifications and product descriptions at any time without notice. Neither circuit patent licenses nor indemnity are expressed or implied. Except as set forth in IXYS Integrated
Circuits Division’s Standard Terms and Conditions of Sale, IXYS Integrated Circuits Division assumes no liability whatsoever, and disclaims any express or implied warranty, relating to
its products including, but not limited to, the implied warranty of merchantability, fitness for a particular purpose, or infringement of any intellectual property right.
The products described in this document are not designed, intended, authorized or warranted for use as components in systems intended for surgical implant into the body, or in other
applications intended to support or sustain life, or where malfunction of IXYS Integrated Circuits Division’s product may result in direct physical harm, injury, or death to a person or severe
property or environmental damage. IXYS Integrated Circuits Division reserves the right to discontinue or make changes to its products at any time without notice.
7
Specification: DS-PAA110L-R06
© Copyright 2012, IXYS Integrated Circuits Division
OptoMOS® is a registered trademark of IXYS Integrated Circuits Division
All rights reserved. Printed in USA.
12/22/2012