LAA100 Dual Single-Pole OptoMOS® Relays INTEGRATED CIRCUITS DIVISION Parameter Blocking Voltage Load Current On-Resistance (max) Ratings 350 120 25 Units VP mArms / mADC Description The LAA100 is a 350V, 120mA, dual single-pole, normally open (1-Form-A) relay featuring low, 25, maximum on-resistance. Features Approvals • 3750Vrms Input/Output Isolation • Low Drive Power Requirements (TTL/CMOS Compatible) • No Moving Parts • High Reliability • Arc-Free With No Snubbing Circuits • FCC Compatible • VDE Compatible • No EMI/RFI Generation • Small 8-Pin DIP Package • Machine Insertable, Wave Solderable • Surface Mount Tape & Reel Version Available • UL Recognized Component: File # E76270 • CSA Certified Component: Certificate # 1175739 • EN/IEC 60950 Compliant Ordering Information Part # LAA100 LAA100P LAA100PTR LAA100S LAA100STR Applications • Telecommunications • Telecom Switching • Tip/Ring Circuits • Modem Switching (Laptop, Notebook, Pocket Size) • Hook Switch • Dial Pulsing • Ground Start • Ringing Injection • Instrumentation • Multiplexers • Data Acquisition • Electronic Switching • I/O Subsystems • Meters (Watt-Hour, Water, Gas) • Medical Equipment—Patient/Equipment Isolation • Security • Aerospace • Industrial Controls Description 8 Pin DIP (50/Tube) 8-Pin Flatpack (50/Tube) 8-Pin Flatpack (1000/Reel) 8-Pin Surface Mount (50/Tube) 8-Pin Surface Mount (1,000/Reel) Pin Configuration AC/DC Configuration + Control - Switch #1 – Control - Switch #1 + Control - Switch #2 – Control - Switch #2 1 8 2 7 3 6 4 5 Load - Switch #1 Load - Switch #1 Load - Switch #2 Load - Switch #2 Switching Characteristics of Normally Open (Form A) Devices Form-A IF 90% 10% ILOAD ton Pb DS-LAA100-R02 toff e3 www.ixysic.com 1 INTEGRATED CIRCUITS DIVISION LAA100 Absolute Maximum Ratings @25ºC Parameter Blocking Voltage Reverse Input Voltage Input Control Current Peak (10ms) Input Power Dissipation 1 Total Power Dissipation 2 Isolation Voltage, Input to Output Operational Temperature Storage Temperature 1 Derate linearly 1.33 mW / ºC 2 Derate linearly 6.67 mW / ºC Ratings 350 5 50 1 150 800 3750 -40 to +85 -40 to +125 Units VP V mA A mW mW Vrms ºC ºC Absolute Maximum Ratings are stress ratings. Stresses in excess of these ratings can cause permanent damage to the device. Functional operation of the device at conditions beyond those indicated in the operational sections of this data sheet is not implied. Electrical Characteristics @ 25ºC Parameter Output Characteristics Load Current Continuous 1 Peak On-Resistance 2 Off-State Leakage Current Switching Speeds Turn-On Turn-Off Output Capacitance Input Characteristics Input Control Current to Activate Input Control Current to Deactivate Input Voltage Drop Reverse Input Current Common Characteristics Capacitance Input to Output 1 2 Conditions Symbol Min Typ Max Units 10ms IL=120mA VL=350V IL ILPK RON ILEAK - - 120 ±350 25 1 mArms / mADC mAP VL = 50V, f=1MHz ton toff COUT - 35 5 5 - ms ms pF IL = 120mA IF = 5mA VR = 5V IF IF VF IR 0.4 0.9 - 0.7 1.2 - 5 1.4 10 mA mA V µA - CI/O - 3 - pF IF = 5mA, VL = 10V µA If both poles operate, the load current must be derated so that the package power dissipation value is not exceeded. Measurement taken within 1 second of on-time. 2 www.ixysic.com R02 INTEGRATED CIRCUITS DIVISION LAA100 PERFORMANCE DATA* 25 25 20 15 10 5 0 15 10 5 1.19 1.21 1.23 1.25 LED Forward Voltage Drop (V) 1.2 Typical IF for Switch Operation (N=50, TA=25ºC, IL=120mADC) 25 Device Count (N) 15 10 5 0 1.3 1.4 1.5 1.6 Turn-On (ms) 1.7 0.65 0.70 0.75 0.80 LED Current (mA) 0.85 10 5 0.08 0.10 0.13 0.15 Turn-Off (ms) 0.17 0.19 Typical On-Resistance Distribution (N=50, TA=25ºC, IL=120mADC) 35 30 20 15 10 5 25 20 15 10 5 0 0.90 0.55 35 15 0.06 0 0.60 20 1.8 Typical IF for Switch Dropout (N=50, TA=25ºC, IL=120mADC) 25 20 Typical Turn-Off Time (N=50, TA=25ºC, IL=120mADC, IF=5mA) 0 0 1.17 Device Count (N) 20 25 Device Count (N) Device Count (N) Device Count (N) 30 Typical Turn-On Time (N=50, TA=25ºC, IL=120mADC, IF=5mA) Device Count (N) 35 Typical LED Forward Voltage Drop (N=50, TA=25ºC, IF=5mA) 0.60 0.65 0.70 0.75 LED Current (mA) 0.80 0.85 13.85 14.00 14.15 14.30 14.45 14.60 14.75 On-Resistance (:) Typical Blocking Voltage Distribution (N=50, TA=25ºC) Device Count (N) 30 25 20 15 10 5 0 390 1.6 IF=50mA 1.2 IF=10mA IF=5mA 1.0 420 3.0 0.30 2.5 0.25 2.0 1.5 1.0 0.5 -40 -20 0 20 40 60 Temperature (ºC) 80 100 120 0.20 0.15 0.10 0.05 0 0.8 Typical Turn-Off vs. LED Forward Current (TA=25ºC, IL=120mADC) Turn-Off (ms) 1.8 1.4 400 405 410 415 Blocking Voltage (VP) Typical Turn-On vs. LED Forward Current (TA=25ºC, IL=120mADC) Turn-On (ms) LED Forward Voltage Drop (V) Typical LED Forward Voltage Drop vs. Temperature 395 0 0 5 10 15 20 25 30 35 40 LED Forward Current (mA) 45 50 0 5 10 15 20 25 30 35 40 45 50 LED Forward Current (mA) *The Performance data shown in the graphs above is typical of device performance. For guaranteed parameters not indicated in the written specifications, please contact our application department. R02 www.ixysic.com 3 INTEGRATED CIRCUITS DIVISION LAA100 PERFORMANCE DATA* Typical IF for Switch Operation vs. Temperature (IL=70mADC) Typical Turn-On vs. Temperature (IL=70mADC) 2.0 1.0 IF=10mA 2.0 1.5 1.0 25 0 20 40 60 80 15 0 -40 -20 0 20 Temperature (ºC) Turn-Off (ms) 4.0 3.0 2.0 1.0 0 -40 -20 0 20 40 60 80 0.50 0.45 0.40 0.35 0.30 0.25 0.20 0.15 0.10 0.05 0 100 120 40 60 80 30 0 20 40 60 80 100 100 IF=10mA IF=10mA IF=5mA IF=5mA Two Poles Operating 80 60 40 100 50 0 -50 -100 20 0 -150 -40 -20 0 20 40 60 80 Temperature (ºC) 0.016 100 120 -2 -1 0 20 15 10 -40 -20 0 0.012 0.010 0.008 0.006 0.004 0.002 0 20 40 60 80 Temperature (ºC) 100 120 Typical Blocking Voltage vs. Temperature 450 440 430 420 410 400 390 1 2 3 -40 -20 0 20 40 60 Temperature (ºC) 80 20 40 60 Temperature (ºC) 80 100 Energy Rating Curve Load Current (A) Leakage (PA) IF=5mA IF=10mA Load Voltage (V) Typical Leakage vs. Temperature Measured across Pins 5&6, 7&8 (VL=350V) -20 100 120 380 -3 0.014 0 -40 80 25 120 Blocking Voltage (VP) Load Current (mA) 120 60 0 -20 Typical Load Current vs. Load Voltage (TA=25oC, IF=5mA) One Pole Operating 40 Typical On-Resistance vs. Temperature (IL=120mADC, Both Poles Operating) Maximum Continuous DC Load Current vs. Temperature 140 20 Typical Turn-Off vs. Temperature (IL=70mADC) Temperature (ºC) 150 0 Temperature (ºC) Temperature (ºC) 160 -20 Temperature (ºC) 5 -40 180 -40 100 120 On-Resistance (:) 5.0 Pulsed IL=100mA 10 5 100 120 Typical IF for Switch Dropout vs. Temperature (IL=70mADC) IF=5mA IF=10mA 0 -20 IF=10mA Continuous Load IL=Max Rated 20 0.5 -40 LED Current (mA) On-Resistance (:) 3.0 Typical On-Resistance vs. Temperature (IL=120mADC, One Pole Operating) IF=5mA IF=5mA 2.5 4.0 0 Load Current (mA) 30 3.0 Turn-On (ms) LED Current (mA) 5.0 100 1.0 0.9 0.8 0.7 0.6 0.5 0.4 0.3 0.2 0.1 0 10Ps 100Ps 1ms 10ms 100ms 1s 10s 100s Time *The Performance data shown in the graphs above is typical of device performance. For guaranteed parameters not indicated in the written specifications, please contact our application department. 4 www.ixysic.com R02 INTEGRATED CIRCUITS DIVISION LAA100 Manufacturing Information Moisture Sensitivity All plastic encapsulated semiconductor packages are susceptible to moisture ingression. IXYS Integrated Circuits Division classified all of its plastic encapsulated devices for moisture sensitivity according to the latest version of the joint industry standard, IPC/JEDEC J-STD-020, in force at the time of product evaluation. We test all of our products to the maximum conditions set forth in the standard, and guarantee proper operation of our devices when handled according to the limitations and information in that standard as well as to any limitations set forth in the information or standards referenced below. Failure to adhere to the warnings or limitations as established by the listed specifications could result in reduced product performance, reduction of operable life, and/or reduction of overall reliability. This product carries a Moisture Sensitivity Level (MSL) rating as shown below, and should be handled according to the requirements of the latest version of the joint industry standard IPC/JEDEC J-STD-033. Device Moisture Sensitivity Level (MSL) Rating LAA100 / LAA100S / LAA100P MSL 1 ESD Sensitivity This product is ESD Sensitive, and should be handled according to the industry standard JESD-625. Reflow Profile This product has a maximum body temperature and time rating as shown below. All other guidelines of J-STD-020 must be observed. Device Maximum Temperature x Time LAA100 / LAA100S 250ºC for 30 seconds LAA100P 260ºC for 30 seconds Board Wash IXYS Integrated Circuits Division recommends the use of no-clean flux formulations. However, board washing to remove flux residue is acceptable. Since IXYS Integrated Circuits Division employs the use of silicone coating as an optical waveguide in many of its optically isolated products, the use of a short drying bake could be necessary if a wash is used after solder reflow processes. Chlorine- or Fluorine-based solvents or fluxes should not be used. Cleaning methods that employ ultrasonic energy should not be used. Pb R02 e3 www.ixysic.com 5 INTEGRATED CIRCUITS DIVISION LAA100 MECHANICAL DIMENSIONS LAA100 2.540 ± 0.127 (0.100 ± 0.005) 9.652 ± 0.381 (0.380 ± 0.015) 8-0.800 DIA. (8-0.031 DIA.) 2.540 ± 0.127 (0.100 ± 0.005) 9.144 ± 0.508 (0.360 ± 0.020) 6.350 ± 0.127 (0.250 ± 0.005) Pin 1 PCB Hole Pattern 7.620 ± 0.254 (0.300 ± 0.010) 6.350 ± 0.127 (0.250 ± 0.005) 0.457 ± 0.076 (0.018 ± 0.003) 3.302 ± 0.051 (0.130 ± 0.002) 7.620 ± 0.127 (0.300 ± 0.005) 7.239 TYP. (0.285) 4.064 TYP (0.160) 7.620 ± 0.127 (0.300 ± 0.005) 0.254 ± 0.0127 (0.010 ± 0.0005) Dimensions mm (inches) 0.813 ± 0.102 (0.032 ± 0.004) LAA100S 9.652 ± 0.381 (0.380 ± 0.015) 2.540 ± 0.127 (0.100 ± 0.005) 6.350 ± 0.127 (0.250 ± 0.005) Pin 1 0.635 ± 0.127 (0.025 ± 0.005) 3.302 ± 0.051 (0.130 ± 0.002) 9.525 ± 0.254 (0.375 ± 0.010) 0.457 ± 0.076 (0.018 ± 0.003) PCB Land Pattern 2.54 (0.10) 8.90 (0.3503) 1.65 (0.0649) 7.620 ± 0.254 (0.300 ± 0.010) 0.254 ± 0.0127 (0.010 ± 0.0005) 0.65 (0.0255) 4.445 ± 0.127 (0.175 ± 0.005) Dimensions mm (inches) 0.813 ± 0.102 (0.032 ± 0.004) LAA100P 2.540 ± 0.127 (0.100 ± 0.005) 6.350 ± 0.127 (0.250 ± 0.005) 0 MIN / 0.102 MAX (0 MIN / 0.004 MAX) 9.398 ± 0.127 (0.370 ± 0.005) Pin 1 9.652 ± 0.381 (0.380 ± 0.015) 7.620 ± 0.254 (0.300 ± 0.010) 2.286 MAX. (0.090 MAX.) 2.54 (0.10) 0.635 ± 0.127 (0.025 ± 0.005) 0.203 ± 0.013 (0.008 ± 0.0005) 8.70 (0.3425) 1.55 (0.0610) 0.65 (0.0255) 2.159 ± 0.025 (0.085 ± 0.001) 0.457 ± 0.076 (0.018 ± 0.003) 0.864 ± 0.120 (0.034 ± 0.004) 6 PCB Land Pattern Dimensions mm (inches) www.ixysic.com R02 INTEGRATED CIRCUITS DIVISION LAA100 LAA100STR Tape & Reel 330.2 DIA. (13.00 DIA.) Top Cover Tape Thickness 0.102 MAX. (0.004 MAX.) W=16.00 (0.63) Bo=10.30 (0.406) K0 =4.90 (0.193) Ao=10.30 (0.406) K1 =4.20 (0.165) Embossed Carrier Embossment P=12.00 (0.472) User Direction of Feed Dimensions mm (inches) NOTES: 1. Dimensions carry tolerances of EIA Standard 481-2 2. Tape complies with all “Notes” for constant dimensions listed on page 5 of EIA-481-2 LAA100PTR Tape & Reel 2.00 (0.079) 330.2 DIA. (13.00 DIA.) Top Cover Tape Thickness 0.102 MAX. (0.004 MAX.) Embossment W = 16.00 (0.63) 7.50 (0.295) Bo = 10.30 (0.406) K0 = 2.70 (0.106) K1 = 2.00 (0.079) Embossed Carrier 4.00 (0.157) Ao = 10.30 (0.406) P = 12.00 (0.472) User Direction of Feed Dimensions mm (inches) NOTES: 1. All dimensions carry tolerances of EIA Standard 481-2 2. The tape complies with all “Notes” for constant dimensions listed on page 5 of EIA-481-2 For additional information please visit our website at: www.ixysic.com IXYS Integrated Circuits Division makes no representations or warranties with respect to the accuracy or completeness of the contents of this publication and reserves the right to make changes to specifications and product descriptions at any time without notice. Neither circuit patent licenses nor indemnity are expressed or implied. Except as set forth in IXYS Integrated Circuits Division’s Standard Terms and Conditions of Sale, IXYS Integrated Circuits Division assumes no liability whatsoever, and disclaims any express or implied warranty, relating to its products including, but not limited to, the implied warranty of merchantability, fitness for a particular purpose, or infringement of any intellectual property right. The products described in this document are not designed, intended, authorized or warranted for use as components in systems intended for surgical implant into the body, or in other applications intended to support or sustain life, or where malfunction of IXYS Integrated Circuits Division’s product may result in direct physical harm, injury, or death to a person or severe property or environmental damage. IXYS Integrated Circuits Division reserves the right to discontinue or make changes to its products at any time without notice. 7 Specification: DS-LAA100-R02 ©Copyright 2012, IXYS Integrated Circuits Division OptoMOS® is a registered trademark of IXYS Integrated Circuits Division All rights reserved. Printed in USA. 12/22/2012