LED Power Supply Product Specifications LP4240-XX-YZ-E Series Switch-Mode LED Driver Total Power 240 Watts Input Voltages 90-264 VAC Number of Outputs Three or Four ANZ#: Z099e, July 31, 2006 SPECIAL FEATURES ELECTRICAL SPECIFICATIONS • • • • • • • • • Three (3) or Four (4) independent Class 2 outputs Input range Frequency In compliance to EN61000-3-2, -3-3 Class D Power Factor Low Inrush Current maximize number of hookup Inrush current Incompliance to NEMA3, IP66 standards Input current Efficiency Suitable for damp or dry locations Suitable for wet location w/adequate connectors EMI filtering Maximum power Aluminum extrusion enclosure, convection cool Line Regulation OCP, OTP and SCP w/ auto-recovery Load Regulation Ripple Noise DIN Rail Mounting – Optional Leakage Current ENVIRONMENTAL Hold up time Operating temperature: -30 to 70 º C (De-rating : 2.5% per ºC from 50ºC~70ºC ) Protection Storage temperature: -40 to 85 º C Humidity (Non-Condensing): 5% to 95% SAFETY Cooling: Convection UL/cUL Vibration Frequency: 5 to 50 Hz MTBF: >100,000 Hours at full load and 25ºC CE ambient conditions (MIL-217F) EMC : Compliant to 47CFR, Part 2, Part15 and Cispr PUB, 22 Class B 90 to 264 VAC, Full range 47 to 63 Hz > 0.95 at full load, 115VAC 5.0 Amps maximum at 115VAC, cold start, 25º C 3.0Amps maximum at 115VAC 85% typical at 230VAC and maximum load 47CFR, Part 2, Part 15 and Cispr PUB, 22 Class A 240W total 1% ±3% 3% typ. 2mA @ 110VAC, 4mA @ 230VAC Half cycle minimum at 120 VAC and 80% of rated load Over-voltage, Over-current, Over-temp. and Short circuit protection UL48, Class 2 Certified MODEL INFORMATION Model # LP4240-12-YZ-E LP4240-15-YZ-E LP4240-24-YZ-E LP3240-24-YZ-E Channel 1 (VDC/Amp) 12VDC 0 ~ 5 Amp 15VDC 0 ~ 4 Amp 24VDC 0 ~ 2.5 Amp 24VDC 0 ~ 3.3 Amp DC Output Channel 2 Channel 3 (VDC/Amp) (VDC/Amp) 12VDC 12VDC 0 ~ 5 Amp 0 ~ 5 Amp 15VDC 15VDC 0 ~ 4 Amp 0 ~ 4 Amp 24VDC 24VDC 0 ~ 2.5 Amp 0 ~ 2.5 Amp 24VDC 24VDC 0 ~ 3.3 Amp 0 ~ 3.3 Amp Channel 4 (VDC/Amp) 12VDC 0 ~ 5 Amp 15VDC 0 ~ 4 Amp 24VDC 0 ~ 2.5 Amp ----- Output per Channel (Watts) Total Output (Watts) 60 240 60 240 60 240 80 240 MECHANICAL DRAWING Model Information – Single DC output LP4240-XX-YZ-E and LP3240-XX-YZ-E XX – DC outputs Y – AC input connector (J – Junction Box) Z – DC output connector (G – Gland, T – Terminal Block or J – Junction Box) E – Aluminum extrusion enclosure length (Refer to mechanical drawing) INDUSTRIES CORP. 5625-A S. Arville, Las Vegas, NV 89118 Tel:702-364-9998 Fax: 702-364-1562 www.magtechind.com Anz099e MECHANICAL DRAWING ( PRELIMINARY ) 8.60 [218.5] 0.39 [10.0] (4X) 5.12 [130.0] 4.33 [110.0] SLOT 0.79x0.20 [20x5] (4X) 0.20 [5.0] 1 2 " NPT (THREADS: 3.5min & 5max) (3X) 1.06 [26.9] 3.00 [76.2] 1.91 [48.6] CAPS (2X) G-TPE Gland, Liquid Tight, AVC INDUSTRIAL CORP FGA13-08 5.98 [152.0] 2.95 [75.0] 1.73 [43.9] 5.12 [130.0] "AC INPUT 100-240VAC" LABEL ON PLATE "NO SERVICE PARTS" LABEL ON SCREW (1 SCREW MIN) 9.07 [230.5] MARKING: "CLASS 2 POWER OUTPUT" ADJACENT TO OUTPUT LEADS INDUSTRIES CORP. 5625-A S. Arville, Las Vegas, NV 89118 Tel:702-364-9998 Fax: 702-364-1562 www.magtechind.com Anz099e