128-pin TQFP - Lattice Semiconductor

Package Diagrams
February 2013
Data Sheet
20-Pin (300-Mil) CERDIP Package
Dimensions in Inches
(DATUM A)
B
N/2
1
4
E
E1
N
E3
e/2
E
DETAIL A
D
A
4
BASE PLANE
(DATUM B)
A2
A1
A
C
SEATING PLANE
e
b2
Z
b
.010 M
L
Z
E2
C A B
b1
(c)
4X
WITH
LEAD FINISH
c1
BASE METAL
(b)
b3
SECTION Z-Z
DETAIL A
S
Y
M
B
O
L
NOTES:
1.
c
7
A
DIMENSIONING AND TOLERANCING PER
ANSI Y14.5M.
2.
ALL DIMENSIONS ARE IN INCHES.
3.
MEASUREMENTS TO BE TAKEN AT A MINIMUM OF
.060 INCHES FROM THE LEAD TIP.
4.
DIMENSIONS D AND E1 INCLUDE ALLOWANCE FOR GLASS
OVERRUN AND MENISCUS, AND LID TO BASE MISMATCH.
5.
DIMENSIONS A, A1 AND L ARE MEASURED WITH THE
PACKAGE SEATED IN JEDEC SEATING PLANE GAUGE GS-003.
6.
E3 IS TO BE MEASURED AT THE LEAD TIPS.
7.
ALLOWED LEAD TIP POSITION RANGE.
A1
A2
b
b1
b2
b3
c
c1
D
E
E1
E2
E3
e
L
N
3
INCHES
MIN. NOM.
.015
.140
.015
.015 .018
.045
.023
.008
.008 .010
.942 .950
.308
.280 .288
.300 REF
.325
.100 BSC
.125
20
MAX.
.200
.175
.023
.021
.065
.045
.014
.012
.970
.325
.296
.410
.200
© 2013 Lattice Semiconductor Corp. All Lattice trademarks, registered trademarks, patents, and disclaimers are as listed at www.latticesemi.com/legal. All other brand
or product names are trademarks or registered trademarks of their respective holders. The specifications and information herein are subject to change without notice.
www.latticesemi.com
1
pkg_03.9
Package Diagrams
20-Pin LCC Package
Dimensions in Inches
D4
D2
.010
X 45
.020
E2
E4
4
.030
X 45
.050
(3 PLACES)
A1
L (19 PLACES)
A
B
3
e
E
.030
.050
D
L1
RADIUS
(TYPICAL)
A2
3
NOTES:
1.
S
Y
M
B
O
L
DIMENSIONING AND TOLERANCING PER
ANSI Y14.5.
2.
ALL DIMENSIONS ARE IN INCHES.
3.
DIMENSIONS D AND E MAY HAVE MATERIAL PROTRUSION
OF .010 INCHES MAXIMUM ABOVE THE DIMENSION SHOWN
NOT TO EXCEED .005 INCHES MAXIMUM PER SIDE.
4.
FLATNESS TOLERANCE IS .004 INCHES PER INCH.
2
A
A1
A2
B
D
D2
D4
E
E2
E4
e
L
L1
INCHES
MIN.
.054
.064
.007
.022
.342
MAX.
.074
.089
.015
.028
.358
.200
.270
.342
.315
.358
.200
.270
.315
.050 BSC
.042
.058
.075
.095
Package Diagrams
20-Pin PLCC Package
Dimensions in Inches
D1
.007
.002
-A-B-
6
S H A-B
A-B S
S D S
-D3
D3
2
1
4
PIN 1 ID ZONE
20
6
-D-
E E1
7
-A-
D3
-B-
4
4
7
E3
E3
//
7
.007
.002
.007
S
Y
M
B
O
L
A
A1
A2
D
D1
D2
D3
E
E1
E2
E3
N
S
S H A-B
A-B S
S D S
H A-B
D S
MIN. NOM. MAX.
.165
.090
.062
.385
.350
.141
.385
.350
.141
.172
.105
.390
.353
.155
.075
.390
.353
.155
.075
20
.180
.120
.083
.395
.356
.169
S
0.050
(N-4PLACES)
DETAIL "J"
D/E
.021
.013
.0105
.0075
.0125
.0075
.395
.356
.169
8
A
.018
.013
8
SECTION A-A
-H-
.004
-CSEATING PLANE
A A
D2/E2
NOTES:
ALL DIMENSIONS AND TOLERANCES CONFORM TO ANSI Y14.5M-1982
2.
ALL DIMENSIONS IN INCHES
3
DATUM PLANE -HLOCATED AT TOP OF MOLD PARTING LINE AND
COINCIDENT WITH TOP OF LEAD WHERE LEAD EXITS PLASTIC BODY
4
DATUMS A-B AND -DTO BE DETERMINED WHERE CENTER LEADS
EXIT PLASTIC BODY AT DATUM PLANE -H-
5
TO BE MEASURED AT SEATING PLANE -C-
6
DIMENSIONS D1 AND E1 DO NOT INCLUDE MOLD PROTRUSION.
ALLOWABLE PROTRUSION IS .010 PER SIDE.
7
-H- ; BOTTOM POINT OF
TOP POINT OF MEASUREMENT IS DATUM
MEASUREMENT IS AT MAJOR FLAT AREA OF LOWER PLASTIC SURFACE
DEFINED BY D3/E3
8
DIMENSION APPLIES TO BASE METAL ONLY
.020
(MIN)
D2/E2
5
1.
3
A2
A1
5
-A-B-D-
.032
.026
.007
S
H A-B
S
D S
.045 MIN.
CONTACT POINT
.025 MIN.
-C-
SEATING PLANE
.021
.013
.007
DETAIL "J"
3
M C A-B
(TYP ALL SIDES)
S
D S
C
Package Diagrams
20-Pin Plastic DIP Package
Dimensions in Inches
-BN/2
E
b1
1
WITH
LEAD FINISH
6
5
CL
E1
(c)
c1
N
(b)
SEE
DETAIL
A
BASE METAL
CL
SECTION Z-Z
c
BASE PLANE
6
eA
5
-A-
D
eB
Z Z
4
7
A2 A
-C.015
EATING
PLANE
A1
10
b
.010
GAGE
PLANE
-H-
e
b2
L
D1 4x
M
C
5
eC
DETAIL A
NOTES:
1. CONTROLLING DIMENSION:
INCH.
2. DIMENSIONING AND TOLERANCING PER
ANSI Y14.5M
3. DISTANCE BETWEEN LEADS INCLUDING DAMBAR
PROTRUSIONS TO BE .005 MINIMUM.
4. DIMENSIONS A, A1 & L ARE MEASURED WITH
THE PACKAGE SEATED IN JEDEC SEATING
PLANE GAUGE GS-3.
5. DIMENSIONS D, D1 AND E1
DO NOT INCLUDE MOLD FLASH OR PROTRUSIONS.
MOLD FLASH OR PROTRUSIONS SHALL NOT EXCEED .010
6. E AND eA MEASURED WITH THE LEADS CONSTRAINED
TO BE PERPENDICULAR TO DATUM -C7. eB AND eC ARE MEASURED AT THE LEAD TIPS
WITH THE LEADS UNCONSTRAINED.
8. N IS THE MAXIMUM NUMBER OF LEAD
POSITIONS.
9. POINTED OR ROUNDED LEAD TIPS ARE PREFERRED
TO EASE INSERTION
10. b2 MAXIMUM DIMENSION DOES NOT
INCLUDE DAMBAR PROTRUSIONS. DAMBAR
PROTRUSIONS SHALL NOT EXCEED .010
11. DATUM PLANE -H- COINCIDENT WITH THE BOTTOM
OF LEAD , WHERE LEAD EXITS BODY
N = 20
4
S
Y
M
B
O
L
MIN. NOM.
MAX.
A
A1
A2
b
b1
b2
c
c1
D
D1
E
E1
e
eA
eB
eC
L
.015
.115 .130
.014 .018
.014 .018
.045 .060
.008 .010
.008 .010
.980 1.030
.005 .300 .310
.240 .250
.100 BSC
.300 BSC
.000
.115 .130
.210
.195
.022
.020
.070
.014
.011
1.060
.325
.280
INCHES
N
O
.430
.060
.150
T
E
4
4
10
5
5
6
5
6
7
7
4
Package Diagrams
24-Pin (300-Mil) CERDIP
Dimensions in Inches
(DATUM A)
B
N/2
1
4
E
E1
N
E3
e/2
E
D
A
4
BASE PLANE
(DATUM B)
A2
A1
A
C
SEATING PLANE
b2
e
Z
b
.010 M
L
Z
c
E2
C A B
b1
(c)
WITH
LEAD FINISH
c1
(b)
SECTION Z-Z
BASE METAL
3
S
Y
M
B
O
L
NOTES:
1.
7
A
DIMENSIONING AND TOLERANCING PER
ANSI Y14.5M.
2.
ALL DIMENSIONS ARE IN INCHES.
3.
MEASUREMENTS TO BE TAKEN AT A MINIMUM OF
.060 INCHES FROM THE LEAD TIP.
4.
DIMENSIONS D AND E1 INCLUDE ALLOWANCE FOR GLASS
OVERRUN AND MENISCUS, AND LID TO BASE MISMATCH.
5.
DIMENSIONS A, A1 AND L ARE MEASURED WITH THE
PACKAGE SEATED IN JEDEC SEATING PLANE GAUGE GS-003.
6.
E3 IS TO BE MEASURED AT THE LEAD TIPS.
7.
ALLOWED LEAD TIP POSITION RANGE.
5
A1
A2
b
b1
b2
c
c1
D
E
E1
E2
E3
e
L
N
INCHES
MIN. NOM. MAX.
.200
.015
.140
.175
.015
.023
.015 .018 .021
.065
.045
.008
.014
.008 .010 .012
1.242 1.250 1.270
.308
.325
.280 .288 .296
.300 REF
.410
.325
.100 BSC
.200
.125
24
Package Diagrams
24-Pin Plastic DIP
Dimensions in Inches
-BN/2
b1
1
E
WITH
LEAD FINISH
6
5
CL
E1
(c)
c1
N
(b)
SEE
DETAIL
A
BASE METAL
SECTION Z-Z
CL
c
BASE PLANE
-A-
6
5
eA
D
eB
Z Z
4
A2 A
7
-C.015
SEATING
PLANE
A1
10
b
.010
GAGE
PLANE
-H-
e
b2
L
D1 4x
M
C
5
eC
DETAIL A
NOTES:
1. CONTROLLING DIMENSION:
INCH.
2. DIMENSIONING AND TOLERANCING PER
ANSI Y14.5M
3. DISTANCE BETWEEN LEADS INCLUDING DAMBAR
PROTRUSIONS TO BE .005 MINIMUM.
4. DIMENSIONS A, A1 & L ARE MEASURED WITH
THE PACKAGE SEATED IN JEDEC SEATING
PLANE GAUGE GS-3.
5. DIMENSIONS D, D1 AND E1
DO NOT INCLUDE MOLD FLASH OR PROTRUSIONS.
MOLD FLASH OR PROTRUSIONS SHALL NOT EXCEED .010
6. E AND eA MEASURED WITH THE LEADS CONSTRAINED
TO BE PERPENDICULAR TO DATUM -C7. eB AND eC ARE MEASURED AT THE LEAD TIPS
WITH THE LEADS UNCONSTRAINED.
8. N IS THE MAXIMUM NUMBER OF LEAD
POSITIONS.
9. POINTED OR ROUNDED LEAD TIPS ARE PREFERRED
TO EASE INSERTION
10. b2 MAXIMUM DIMENSIONS DOES NOT
INCLUDE DAMBAR PROTRUSIONS. DAMBAR
PROTRUSIONS SHALL NOT EXCEED .010
11. DATUM PLANE -H- COINCIDENT WITH THE BOTTOM
OF LEAD , WHERE LEAD EXITS BODY
N = 24
6
S
Y
M
B
O
L
MIN. NOM.
MAX.
A
A1
A2
b
b1
b2
c
c1
D
D1
E
E1
e
eA
eB
eC
L
.015
.115 .130
.014 .018
.014 .018
.045 .060
.008 .010
.008 .010
1.230 1.250
.005 .300 .310
.240 .250
.100 BSC
.300 BSC
.000
.115 .130
.210
.195
.022
.020
.070
.014
.011
1.280
.325
.280
INCHES
N
O
.430
.060
.150
T
E
4
4
10
5
5
6
5
6
7
7
Package Diagrams
24-Pin QFNS Package
Dimensions in Millimeters
2X
0.15 C A
2X
N
PIN #1 ID FIDUCIAL 4
LOCATED IN THIS AREA
D2
D
A
L
24X
0.15 C B
1
N
1
4
PIN 1 ID AREA
E2
E
e
B
b
0.10
M
C A B
5
0.50 TYP
4X
TOP VIEW
BOTTOM VIEW
VIEW A
VIEW A
A
C
0.08 C
SIDE VIEW
6
SEATING
PLANE
A1
A3
NOTES: UNLESS OTHERWISE SPECIFIED
SYMBOL
1.
DIMENSIONS AND TOLERANCES
PER ANSI Y14.5M.
2.
ALL DIMENSIONS ARE IN MILLIMETERS.
3.
DRAWING CONFORMS TO JEDEC MO-220, VARIATION VGGD-9.
MIN.
NOM.
MAX.
A
0.80
0.90
1.00
A1
0.00
0.02
0.05
A3
D2
4
EXACT SHAPE AND SIZE OF THIS
FEATURE IS OPTIONAL.
5
DIMENSION b APPLIES TO PLATED
TERMINAL AND IS MEASURED BETWEEN
0.15 AND 0.30 mm FROM TERMINAL TIP.
6
APPLIES TO EXPOSED PORTION OF TERMINALS.
0.2 REF
D
4.0 BSC
1.05
E
2.45
4.0 BSC
E2
1.05
-
2.45
b
0.18
0.25
0.30
e
L
7
-
0.50 BSC
0.45
0.50
0.55
Package Diagrams
25-Ball WLCS Package
Dimensions in Millimeters
8
Package Diagrams
28-Pin LCC Package
Dimensions in Inches
D4
D2
.010
X 45
.020
E2
E4
4
.030
X 45
.050
(3 PLACES)
A1
L (27 PLACES)
A
B
e
.030
3
E
.050
D
RADIUS
(TYPICAL)
A2
L1
S
Y
M
B
O
L
3
NOTES:
1.
DIMENSIONING AND TOLERANCING PER
ANSI Y14.5.
2.
ALL DIMENSIONS ARE IN INCHES.
3.
DIMENSIONS D AND E MAY HAVE MATERIAL PROTRUSION
OF .010 INCHES MAXIMUM ABOVE THE DIMENSION SHOWN
NOT TO EXCEED .005 INCHES MAXIMUM PER SIDE.
4.
FLATNESS TOLERANCE IS .004 INCHES PER INCH.
9
INCHES
MIN.
MAX.
A .054
.074
.089
A1 .064
.015
A2 .007
.022
.028
B
.440
.460
D
.300
D2
.403
D4 .370
.440
.460
E
E2
.300
E4 .370
.403
e
.050 BSC
L
.042
.058
L1 .075
.095
Package Diagrams
28-Pin PLCC Package
Dimensions in Inches
.007
S
H A-B
S
D S
D
D1
.007
.002
-A-B-
6
S H A-B
A-B S
S D S
-D-
4
PIN 1 ID ZONE
1
28
D3
6
-D-
E E1
7
-A-
D3
-B-
4
4
7
E3
E3
//
.007
.002
S H A-B
A-B S
S D S
H A-B
D S
7
.007
S
Y
M
B
O
L
A
A1
A2
D
D1
D2
D3
E
E1
E2
E3
N
S
MIN. NOM. MAX.
.165
.090
.062
.485
.450
.191
.485
.450
.191
.172
.105
.490
.453
.205
.125
.490
.453
.205
.125
28
.180
.120
.083
.495
.456
.219
S
0.050
(N-4PLACES)
DETAIL "J"
D/E
.021
.013
.0105
.0075
8
.0125
.0075
.495
.456
.219
-H-
A
.018
.013
8
SECTION A-A
.004
-CSEATING PLANE
A A
D2/E2
NOTES:
ALL DIMENSIONS AND TOLERANCES CONFORM TO ANSI Y14.5M-1982
2.
ALL DIMENSIONS IN INCHES
3
-HDATUM PLANE
LOCATED AT TOP OF MOLD PARTING LINE AND
COINCIDENT WITH TOP OF LEAD WHERE LEAD EXITS PLASTIC BODY
4
TO BE DETERMINED WHERE CENTER LEADS
DATUMS A-B AND -DEXIT PLASTIC BODY AT DATUM PLANE -H-
5
TO BE MEASURED AT SEATING PLANE
6
DIMENSIONS D1 AND E1 DO NOT INCLUDE MOLD PROTRUSION.
ALLOWABLE PROTRUSION IS .010 PER SIDE.
-C-
TOP POINT OF MEASUREMENT IS DATUM -H- ; BOTTOM POINT OF
MEASUREMENT IS AT MAJOR FLAT AREA OF LOWER PLASTIC SURFACE
DEFINED BY D3/E3
8
DIMENSION APPLIES TO BASE METAL ONLY
5
-A-B-D-
.032
.026
.007
S
H A-B
S
D S
.045 MIN.
CONTACT POINT
7
.020
(MIN)
D2/E2
5
1.
3
A2
A1
.025 MIN.
-C-
SEATING PLANE
.021
.013
.007
DETAIL "J"
10
M C A-B
(TYP ALL SIDES)
S
D S
C
Package Diagrams
28-Pin Plastic DIP Package
Dimensions in Inches
1
N/2
NOTE:
1 CONTROLLING DIMENSION: INCHES
2 DIMENSIONING AND TOLERANCING
PER ANSI Y14.5M-1982
3 ALL END LEADS IN THIS FAMILY ARE 1/2 LEADS
4 DIMENSION A, A1, AND L ARE MEASURED WITH THE
PACKAGE SEATED IN JEDEC SEATING PLANE GAUGE GS-3
5 D AND E1 DIMENSIONS DO NOT INCLUDE MOLD
FLASH OR PROTRUSION. MOLD FLASH AND
PROTRUSION SHALL NOT EXCEED 0.010
6 E AND eA MEASURED WITH THE LEADS
CONSTRAINED TO BE PERPENDICULAR TO PLANE A
7 eB AND eC ARE MEASURED AT THE LEAD TIPS
WITH THE LEADS UNCONSTRAINED. eC MUST BE
ZERO OR GREATER
8 N IS THE NUMBER OF TERMINAL POSITIONS
9 B1 AND B2 MAXIMUM DIMENSIONS DO NOT INCLUDE
DAMBAR PROTRUSIONS. DAMBAR PROTRUSIONS
SHALL NOT EXCEED 0.010
-C-
E1
N
E
S
Y
M
B
O
L
CL
eA
eC
A
A1
A2
B
B1
B2
C
D
D1
E
E1
e
eA
eB
eC
L
N
C
eB
-B-
D
D1
L
SEATING PLANE
A2
-AA1
B2
4x
A
e
B
+
B1
11
0.015 M
0.010 M
A B
A
C
INCHES
MIN. NOM.
MAX.
.180
.015
.150
.120 .135
.022
.014 .018
.060
.045 .050
.030 .040 .045
.008 .010 .015
1.345 1.365 1.385
1.300 BSC
.300 .310 .325
.275 .285
.295
.100 BSC
.300 BSC
.430
.060
.000
.110 .130 .150
28
Package Diagrams
28-Pin SSOP Package
Dimensions in Millimeters
+
3
D
5
e
0.15 M C
A S
B S
b
-AA
Pin 1 Identifier
3
2
- C -
1
0.10
A1
SEATING
PLANE
E
C
SIDE VIEW
-BE1
A2
3
N
+
0.20 M
C
A S
B S
PARTING LINE
TOP VIEW
SEE
DETAIL "A"
S
Y
M
B
O
L
COMMON
DIMENSIONS
MIN.
NOM.
MAX.
A
A1
A2
b
b1
c
c1
D
E1
-0.05
1.65
0.22
0.22
0.09
0.09
9.90
5.00
e
E
L
L1
N
OC
R1
7.40
0.55
0
0.09
2 NX R R1
GAUGE PLANE
OC
-2.0
--1.85
1.75
0.38
0.30
0.33
-0.25
0.21
0.15
10.20
10.50
5.30
5.60
0.65 BSC
7.80
8.20
0.75
0.95
1.25 REF.
28
4
--
END VIEW
A
0.25 BSC
A
L
4
SEATING PLANE
L1
DETAIL 'A'
WITH LEAD FINISH
b1
8
--
c
c1
(b)
5
SECTION A-A
BASE METAL
6
NOTES:
1. CONTROLLING DIMENSION: MILLIMETERS.
2. DIMENSIONING & TOLERANCES PER ANSI.Y14.5M-1982.
3. "D" & "E1" DO NOT INCLUDE MOLD FLASH OR
PROTRUSIONS, BUT DO INCLUDE MOLD MISMATCH
AND ARE MEASURED AT THE PARTING LINE.
MOLD FLASH OR PROTRUSIONS SHALL NOT
EXCEED 0.20mm PER SIDE.
5. DIMENSION b DOES NOT INCLUDE DAMBAR PROTRUSION/INTRUSION.
ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.13mm TOTAL IN
EXCESS OF b DIMENSION AT MAXIMUM MATERIAL CONDITION.
DAMBAR INTRUSION SHALL NOT REDUCE DIMENSION b BY MORE
THAN 0.07mm AT LEAST MATERIAL CONDITION.
6. THESE DIMENSIONS APPLY TO THE FLAT SECTION OF THE LEAD
BETWEEN 0.10 & 0.25mm FROM THE LEAD TIP
4. TO BE DETERMINED AT THE SEATING PLANE
7. "N" IS THE NUMBER OF TERMINAL POSITIONS
12
Package Diagrams
32-Pin QFNS Package Option 1: Power Manager II, iCE40
Dimensions in Millimeters
2X
0.15
D
A
C A
D2
2X
N
0.15
C B
L
32X
3
PIN #1 ID FIDUCIAL
LOCATED IN THIS AREA
N
1
1
3
PIN 1 ID AREA
E2
E
e
B
TOP VIEW
0.50 TYP
VIEW A
4X
b
M
C A B
BOTTOM VIEW
VIEW A
C
0.10
A
SIDE VIEW
0.08
C
SEATING
PLANE
A3
5
A1
SYMBOL
MIN.
NOM.
MAX.
NOTES: UNLESS OTHERWISE SPECIFIED
A
0.80
0.90
1.00
1.
DIMENSIONS AND TOLERANCES
PER ANSI Y14.5M.
A1
0.00
0.02
0.05
A3
0.2 REF
ALL DIMENSIONS ARE IN MILLIMETERS.
D
5.0 BSC
EXACT SHAPE AND SIZE OF THIS
FEATURE IS OPTIONAL.
D2
DIMENSION b APPLIES TO PLATED
TERMINAL AND IS MEASURED BETWEEN
0.15 AND 0.30 mm FROM TERMINAL TIP.
E2
1.25
2.70
3.75
b
0.18
0.24
0.30
2.
3
4
1.25
E
3.75
5.0 BSC
e
5
2.70
0.50 BSC
APPLIES TO EXPOSED PORTION OF TERMINALS.
L
13
0.30
0.40
0.50
4
Package Diagrams
32-Pin QFNS Package Option 2: MachXO2
Dimensions in Millimeters
2X
0.15
C A
D
A
D2
2X
N
0.15
L
C B
3
PIN #1 ID FIDUCIAL
(CORNER CHAMFER)
32
32X
1
1
3
PIN 1 ID AREA
E2
E
e
B
b
TOP VIEW
0.45 TYP
4X
VIEW A
0.10
M
C
5
CA B
BOTTOM VIEW
VIEW A
A
C
SIDE VIEW
0.08
SEATING
PLANE
A1
A3
SYMBOL
MIN.
NOM.
MAX.
NOTES: UNLESS OTHERWISE SPECIFIED
A
0.50
0.55
0.60
1.
DIMENSIONS AND TOLERANCES
PER ANSI Y14.5M.
A1
0.00
0.02
0.05
ALL DIMENSIONS ARE IN MILLIMETERS.
D
3
EXACT SHAPE AND SIZE OF THIS
FEATURE IS OPTIONAL.
D2
DIMENSION b APPLIES TO PLATED
TERMINAL AND IS MEASURED BETWEEN
0.15 AND 0.30 mm FROM TERMINAL TIP.
E2
4
3.10
3.20
3.30
b
0.20
0.25
0.30
2.
A3
0.2 REF
5.0 BSC
3.10
E
0.50 BSC
APPLIES TO EXPOSED PORTION OF TERMINALS.
L
14
3.30
5.0 BSC
e
5
3.20
0.35
0.40
0.45
4
Package Diagrams
36-Ball ucBGA Package
Dimensions in Millimeters
6
M
e
5
aaa (4X)
PIN #1 ID FIDUCIAL
LOCATED IN THIS AREA
D
A
B
6
5
4
3
2
1
A
S
B
C
E
N
D
E
F
e
6
4X
S
b
A2
A
bbb
3
C
.15 M C A B
.05 M C
4
ddd
C
C
A1
NOTES: UNLESS OTHERWISE SPECIFIED
1.
DIMENSIONS AND TOLERANCES
PER ANSI Y14.5M.
2.
ALL DIMENSIONS ARE IN MILLIMETERS.
3
DIMENSION "b" IS MEASURED AT THE
MAXIMUM SOLDER BALL DIAMETER,
PARALLEL TO PRIMARY DATUM C
SYMBOL
MIN.
NOM.
A
-
-
A1
0.10
-
-
A2
-
-
0.90
D/E
2.50 BSC
M/N
2.00 BSC
S
0.20 BSC
b
4
PRIMARY DATUM C AND SEATING
PLANE ARE DEFINED BY THE SPHERICAL
CROWNS OF THE SOLDER BALLS.
5
BILATERAL TOLERANCE ZONE IS APPLIED
TO EACH SIDE OF THE PACKAGE BODY.
6
EXACT SHAPE AND SIZE OF THIS FEATURE
IS OPTIONAL.
0.20
1.00
0.30
0.40 BSC
e
15
0.25
MAX.
aaa
-
-
0.10
bbb
-
-
0.10
ddd
-
-
0.10
Package Diagrams
44-Pin JLCC Package
Dimensions in Inches
(N PLACES)
D
.011 M
D1
A
B
L
B2
D2
E2
C
L1
Q
L2
B
B
R
E1
E
DETAIL A
B1
C
C1
BASE METAL
B
DETAIL A
A1
SECTION B-B
A
-A.004
SEATING
PLANE
WITH
LEAD FINISH
.050
.020 MIN.
D4
E4
S
Y
INCHES
M
B
O
L
NOTES:
1.
DIMENSIONING AND TOLERANCING PER ANSI Y14.5M.
2.
ALL DIMENSIONS ARE IN INCHES.
3.
CORNER CHAMFERS AND/OR NOTCHES ARE OPTIONAL.
16
A
A1
B
B1
B2
C
C1
D/E
D1/E1
D2/E2
D4/E4
L
L1
L2
Q
R
N
MAX.
MIN.
.115
.190
.065 REF
.023
.013
.020
.013
.035
.022
.007
.013
.010
.007
.675 .690 .700
.620
.660
.500 BSC
.630 BSC
.005
.020
.025
.003
.020
.040
44
Package Diagrams
44-Pin PLCC Package
Dimensions in Inches
.007
S
H A-B
S
D S
D
D1
.007
.002
-A-B-
6
S H A-B
A-B S
S D S
-D1
D3
4
PIN 1 ID ZONE
44
6
-D-
E E1
7
-A-
D3
-B-
4
4
7
E3
E3
//
7
.007
.002
.007
S
Y
M
B
O
L
A
A1
A2
D
D1
D2
D3
E
E1
E2
E3
N
S
S H A-B
A-B S
S D S
H A-B
D S
MIN. NOM. MAX.
.165
.090
.062
.685
.650
.291
.685
.650
.291
.172
.105
.690
.653
.305
.225
.690
.653
.305
.225
44
.180
.120
.083
.695
.656
.319
S
0.050
(N-4PLACES)
DETAIL "J"
D/E
.021
.013
.0105
.0075
.0125
.0075
.695
.656
.319
8
A
.018
.013
8
SECTION A-A
-H-
.004
-CSEATING PLANE
A A
D2/E2
NOTES:
ALL DIMENSIONS AND TOLERANCES CONFORM TO ANSI Y14.5M-1982
2.
ALL DIMENSIONS IN INCHES
3
-HDATUM PLANE
LOCATED AT TOP OF MOLD PARTING LINE AND
COINCIDENT WITH TOP OF LEAD WHERE LEAD EXITS PLASTIC BODY
4
DATUMS A-B AND -DTO BE DETERMINED WHERE CENTER LEADS
EXIT PLASTIC BODY AT DATUM PLANE -H-
5
TO BE MEASURED AT SEATING PLANE -C-
6
DIMENSIONS D1 AND E1 DO NOT INCLUDE MOLD PROTRUSION.
ALLOWABLE PROTRUSION IS .010 PER SIDE.
7
TOP POINT OF MEASUREMENT IS DATUM -H- ; BOTTOM POINT OF
MEASUREMENT IS AT MAJOR FLAT AREA OF LOWER PLASTIC SURFACE
DEFINED BY D3/E3
8
DIMENSION APPLIES TO BASE METAL ONLY
.020
(MIN)
D2/E2
5
1.
3
A2
A1
5
-A-B-D-
.032
.026
.007
S
H A-B
S
D S
.045 MIN.
CONTACT POINT
.025 MIN.
-C-
SEATING PLANE
.021
.013
.007
DETAIL "J"
17
M C A-B
(TYP ALL SIDES)
S
D S
C
Package Diagrams
44-Pin TQFP Package (1.0mm thick)
Dimensions in Millimeters
PIN 1 INDICATOR
0.20 C A-B
D 44X
D
3
A
MARKING
ORIENTATION
e
E1
E
B
3
D
8
D1
3
TOP VIEW
4X
0.20 H A-B
D
BOTTOM VIEW
SIDE VIEW
SEE DETAIL 'A'
b
0.20 M C A-B
SEATING PLANE
D
C
A
0.10 C
1
SECTION B-B
B
0-7∞
L
1.00 REF.
DETAIL 'A'
BASE METAL
NOTES:
1.
DIMENSIONING AND TOLERANCING PER ANSI Y14.5 - 1982.
2.
ALL DIMENSIONS ARE IN MILLIMETERS.
3.
DATUMS A, B AND D TO BE DETERMINED AT DATUM PLANE H.
4.
DIMENSIONS D1 AND E1 DO NOT INCLUDE MOLD PROTRUSION.
ALLOWABLE MOLD PROTRUSION IS 0.254 MM ON D1 AND E1
DIMENSIONS.
6.
SECTION B-B:
THESE DIMENSIONS APPLY TO THE FLAT SECTION OF THE
LEAD BETWEEN 0.10 AND 0.25 MM FROM THE LEAD TIP.
7.
A1 IS DEFINED AS THE DISTANCE FROM THE SEATING PLANE
TO THE LOWEST POINT ON THE PACKAGE BODY.
SYMBOL
MIN.
NOM.
MAX.
A
-
-
1.20
A1
0.05
-
0.15
A2
.95
1.00
1.05
D
12.00 BSC
D1
10.00 BSC
E
12.00 BSC
10.00 BSC
E1
5. THE TOP OF PACKAGE MAY BE SMALLER THAN THE BOTTOM
OF THE PACKAGE BY 0.15 MM.
8.
0.20 MIN.
A1
c1
b
0.25
B
LEAD FINISH
b
c
GAUGE PLANE
H
A2
L
EXACT SHAPE OF EACH CORNER IS OPTIONAL.
18
0.45
0.60
N
44
e
0.80 BSC
0.75
0.37
0.45
0.30
0.35
0.40
0.09
0.15
0.20
0.09
0.13
0.16
b
0.30
b1
c
c1
Package Diagrams
44-Pin TQFP Package (1.4mm thick)
Dimensions in Millimeters
PIN 1 INDICATOR
0.20 C A-B
D 44X
D
3
A
MARKING
ORIENTATION
e
E1
E
B
3
D
8
D1
3
TOP VIEW
4X
0.20 H A-B
D
BOTTOM VIEW
SIDE VIEW
SEE DETAIL 'A'
b
0.20 M C A-B
SEATING PLANE
D
C
A
0.10 C
1
SECTION B-B
0.20 MIN.
A1
c1
b
0.25
B
LEAD FINISH
b
c
GAUGE PLANE
H
A2
B
0-7∞
L
1.00 REF.
DETAIL 'A'
BASE METAL
NOTES:
1.
DIMENSIONING AND TOLERANCING PER ANSI Y14.5 - 1982.
2.
ALL DIMENSIONS ARE IN MILLIMETERS.
3.
DATUMS A, B AND D TO BE DETERMINED AT DATUM PLANE H.
4.
DIMENSIONS D1 AND E1 DO NOT INCLUDE MOLD PROTRUSION.
ALLOWABLE MOLD PROTRUSION IS 0.254 MM ON D1 AND E1
DIMENSIONS.
5. THE TOP OF PACKAGE MAY BE SMALLER THAN THE BOTTOM
OF THE PACKAGE BY 0.15 MM.
6.
SECTION B-B:
THESE DIMENSIONS APPLY TO THE FLAT SECTION OF THE
LEAD BETWEEN 0.10 AND 0.25 MM FROM THE LEAD TIP.
7.
A1 IS DEFINED AS THE DISTANCE FROM THE SEATING PLANE
TO THE LOWEST POINT ON THE PACKAGE BODY.
8.
EXACT SHAPE OF EACH CORNER IS OPTIONAL.
SYMBOL
MIN.
NOM.
MAX.
A
-
-
1.60
A1
0.05
-
0.15
A2
1.35
1.40
1.45
D
12.00 BSC
D1
10.00 BSC
E
12.00 BSC
E1
10.00 BSC
L
19
0.45
0.60
N
44
e
0.80 BSC
0.75
b
0.30
0.37
0.45
b1
0.30
0.35
0.40
c
0.09
0.15
0.20
c1
0.09
0.13
0.16
Package Diagrams
48-Pin TQFP Package (1.0mm thick)
Dimensions in Millimeters
0.20 C A-B
PIN 1 INDICATOR
D 48X
D
3
A
MARKING
ORIENTATION
B
e
D
8
E1
E
3
D1
3
TOP VIEW
4X
0.20 H A-B
D
BOTTOM VIEW
SEE DETAIL 'A'
SEATING PLANE
b
0.08 M C A-B
C
D
A
GAUGE PLANE
H
A2
0.25
B
LEAD FINISH
b
0.08 C
A1
c1
c
b
SECTION B-B
0-7∞
L
DETAIL 'A'
1
B
0.20 MIN.
BASE METAL
NOTES:
1.00 REF.
SYMBOL
MIN.
NOM.
MAX.
A
-
-
1.20
-
0.15
1.00
1.05
A1
0.05
1.
DIMENSIONING AND TOLERANCING PER ANSI Y14.5 - 1982.
A2
.95
2.
ALL DIMENSIONS ARE IN MILLIMETERS.
D
9.00 BSC
3.
DATUMS A, B AND D TO BE DETERMINED AT DATUM PLANE H.
D1
7.00 BSC
4.
DIMENSIONS D1 AND E1 DO NOT INCLUDE MOLD PROTRUSION.
ALLOWABLE MOLD PROTRUSION IS 0.254 MM ON D1 AND E1
DIMENSIONS.
E
9.00 BSC
E1
7.00 BSC
5. THE TOP OF PACKAGE MAY BE SMALLER THAN THE BOTTOM
OF THE PACKAGE BY 0.15 MM.
L
N
48
6.
SECTION B-B:
THESE DIMENSIONS APPLY TO THE FLAT SECTION OF THE
LEAD BETWEEN 0.10 AND 0.25 MM FROM THE LEAD TIP.
e
0.50 BSC
b
0.17
0.22
0.27
7.
A1 IS DEFINED AS THE DISTANCE FROM THE SEATING PLANE
TO THE LOWEST POINT ON THE PACKAGE BODY.
b1
0.17
0.20
0.23
c
0.09
0.15
0.20
8.
EXACT SHAPE OF EACH CORNER IS OPTIONAL.
c1
0.09
0.13
0.16
20
0.45
0.60
0.75
Package Diagrams
48-Pin TQFP Package (1.4mm thick)
Dimensions in Millimeters
PIN 1 INDICATOR
0.20 C A-B
D
0.20 H A-B D
D
D1
N
3. A
1
MARKING
ORIENTATION
B
e
D
8. 4X
E1
E
3.
3.
SEE DETAIL "A"
H
b
0.08
C
M C A -B D
A
SEATING PLANE
B
0.08 C
LEAD FINISH
b
GAUGE PLANE
0.25
A2
A1
B
0.20 MIN.
0-7∞
L
1.00 REF.
c
c1
b
DETAIL "A"
1
BASE METAL
SECTION B - B
NOTES:
1.
DIMENSIONING AND TOLERANCING PER ANSI Y14.5 - 1982.
2.
ALL DIMENSIONS ARE IN MILLIMETERS.
3.
DATUMS A, B AND D TO BE DETERMINED AT DATUM PLANE H.
4.
DIMENSIONS D1 AND E1 DO NOT INCLUDE MOLD PROTRUSION.
ALLOWABLE MOLD PROTRUSION IS 0.254 MM ON D1 AND E1
DIMENSIONS.
5. THE TOP OF PACKAGE MAY BE SMALLER THAN THE BOTTOM
OF THE PACKAGE BY 0.15 MM.
6.
A1 IS DEFINED AS THE DISTANCE FROM THE SEATING PLANE
TO THE LOWEST POINT ON THE PACKAGE BODY.
8.
EXACT SHAPE OF EACH CORNER IS OPTIONAL.
MIN.
NOM.
MAX.
A
-
-
1.60
A1
0.05
-
0.15
A2
1.35
1.40
1.45
D
9.00 BSC
D1
7.00 BSC
E
9.00 BSC
E1
7.00 BSC
L
SECTION B-B:
THESE DIMENSIONS APPLY TO THE FLAT SECTION OF THE
LEAD BETWEEN 0.10 AND 0.25 MM FROM THE LEAD TIP.
7.
SYMBOL
21
0.45
0.60
N
48
e
0.50 BSC
0.75
b
0.17
0.22
0.27
b1
0.17
0.20
0.23
c
0.09
0.15
0.20
c1
0.09
0.13
0.16
Package Diagrams
48-Pin QFNS Package
Dimensions in Millimeters
2X
0.15
D
A
2X
N
PIN #1 ID FIDUCIAL
LOCATED IN THIS AREA
D2
C A
0.15
C B
L
48X
3
N
1
1
3
PIN 1 ID AREA
E2
E
e
B
TOP VIEW
0.50 TYP
b
0.10
M
C A B
4
BOTTOM VIEW
4X
VIEW A
VIEW A
C
A
SIDE VIEW
0.08
SEATING
PLANE
A3
SYMBOL
C
5
A1
MIN.
NOM.
MAX.
NOTES: UNLESS OTHERWISE SPECIFIED
A
0.80
0.90
1.00
1.
DIMENSIONS AND TOLERANCES
PER ANSI Y14.5M.
A1
0.00
0.02
0.05
A3
0.2 REF
ALL DIMENSIONS ARE IN MILLIMETERS.
D
7.0 BSC
EXACT SHAPE AND SIZE OF THIS
FEATURE IS OPTIONAL.
D2
DIMENSION b APPLIES TO PLATED
TERMINAL AND IS MEASURED BETWEEN
0.15 AND 0.30 mm FROM TERMINAL TIP.
E2
3.00
-
5.80
b
0.18
0.24
0.30
2.
3
4
3.00
E
5.80
7.0 BSC
e
5
-
0.50 BSC
APPLIES TO EXPOSED PORTION OF TERMINALS.
L
22
0.30
0.40
0.50
Package Diagrams
49-Ball caBGA Package
Dimensions in Millimeters
5
(4X)
aaa
A1 BALL I.D.
IDENTIFIER
M
A
D
B
7
6
5
4
3
2
1
A
B
S
C
D
E
N
E
F
G
e
e
S
6
4X
3
A2
A
b
.15 M C A B
.08 M C
bbb
ddd
C
C
4
C
A1
SYMBOL
NOTES: UNLESS OTHERWISE SPECIFIED
1.
DIMENSIONS AND TOLERANCES
PER ANSI Y14.5M.
2.
ALL DIMENSIONS ARE IN MILLIMETERS.
3
DIMENSION "b" IS MEASURED AT THE
MAXIMUM SOLDER BALL DIAMETER,
PARALLEL TO PRIMARY DATUM C
4
PRIMARY DATUM C AND SEATING
PLANE ARE DEFINED BY THE SPHERICAL
CROWNS OF THE SOLDER BALLS.
5
BILATERAL TOLERANCE ZONE IS APPLIED
TO EACH SIDE OF THE PACKAGE BODY.
6
EXACT SHAPE AND SIZE OF THIS FEATURE
IS OPTIONAL.
MIN.
MAX.
A
1.30
1.40
1.50
A1
0.31
0.36
0.41
A2
0.99
1.04
1.09
D/E
7.00 BSC
M/N
4.80 BSC
S
0 BSC
b
0.40
e
23
NOM.
0.46
0.52
0.80 BSC
aaa
-
-
0.10
bbb
-
-
0.10
ddd
-
-
0.12
Package Diagrams
49-Ball ucBGA Package
Dimensions in Millimeters
5
aaa (4X)
6
M
e
7
6
5
4
D
PIN #1 ID FIDUCIAL
LOCATED IN THIS AREA
3
2
A
B
1
A
B
C
E
N
D
E
F
G
e
4X
6
bbb
3
A2
A
b
C
.15 M C A B
.05 M C
4
ddd
C
C
A1
NOTES: UNLESS OTHERWISE SPECIFIED
1.
DIMENSIONS AND TOLERANCES
PER ANSI Y14.5M.
2.
ALL DIMENSIONS ARE IN MILLIMETERS.
3
DIMENSION "b" IS MEASURED AT THE
MAXIMUM SOLDER BALL DIAMETER,
PARALLEL TO PRIMARY DATUM C
SYMBOL
MIN.
NOM.
A
-
-
A1
0.10
-
-
A2
-
-
0.90
D/E
3.00 BSC
M/N
2.40 BSC
b
0.20
PRIMARY DATUM C AND SEATING
PLANE ARE DEFINED BY THE SPHERICAL
CROWNS OF THE SOLDER BALLS.
5
BILATERAL TOLERANCE ZONE IS APPLIED
TO EACH SIDE OF THE PACKAGE BODY.
6
EXACT SHAPE AND SIZE OF THIS FEATURE
IS OPTIONAL.
24
1.00
0.30
0.40 BSC
e
4
0.25
MAX.
aaa
-
-
0.10
bbb
-
-
0.10
ddd
-
-
0.10
Package Diagrams
56-Ball csBGA Package
Dimensions in Millimeters
5
(4X)
aaa
A1 BALL I.D.
IDENTIFIER
M
D
A
B
10 9
8
7
6
5
4
3
2
1
A
B
C
S
D
E
N
F
E
G
H
J
K
e
e
4X
S
6
b
3
.15 M C A B
.05 M C
bbb
C
A1
NOTES: UNLESS OTHERWISE SPECIFIED
1.
DIMENSIONS AND TOLERANCES
PER ANSI Y14.5M.
2.
ALL DIMENSIONS ARE IN MILLIMETERS.
C
C
ddd
4
3
A2
A
DIMENSION "b" IS MEASURED AT THE
MAXIMUM SOLDER BALL DIAMETER,
PARALLEL TO PRIMARY DATUM C
MIN.
A
1.10
A1
0.15
-
-
A2
-
-
1.10
PRIMARY DATUM C AND SEATING
PLANE ARE DEFINED BY THE SPHERICAL
CROWNS OF THE SOLDER BALLS.
5
BILATERAL TOLERANCE ZONE IS APPLIED
TO EACH SIDE OF THE PACKAGE BODY.
6
EXACT SHAPE AND SIZE OF THIS FEATURE
IS OPTIONAL.
1.23
6.00 BSC
M/N
4.50 BSC
S
0.25 BSC
0.25
0.30
1.35
0.35
0.50 BSC
e
25
NOM.
D/E
b
4
MAX.
SYMBOL
aaa
-
-
0.10
bbb
-
-
0.10
ddd
-
-
0.08
Package Diagrams
64-Ball csBGA Package
Dimensions in Millimeters
aaa (4X)
5
6
M
D
A
PIN #1 ID FIDUCIAL
LOCATED IN THIS AREA
e
8
7
6
5
4
3
2
B
1
A
B
S
C
D
E
N
E
F
G
H
e
4X
S
6
bbb
3
A2
A
b
C
.15 M C A B
.05 M C
4
ddd
C
C
A1
NOTES: UNLESS OTHERWISE SPECIFIED
1.
DIMENSIONS AND TOLERANCES
PER ANSI Y14.5M.
2.
ALL DIMENSIONS ARE IN MILLIMETERS.
3
DIMENSION "b" IS MEASURED AT THE
MAXIMUM SOLDER BALL DIAMETER,
PARALLEL TO PRIMARY DATUM C
SYMBOL
MIN.
NOM.
A
0.90
1.00
A1
0.15
-
-
A2
-
-
0.85
D/E
5.00 BSC
M/N
3.50 BSC
S
0.25 BSC
b
4
PRIMARY DATUM C AND SEATING
PLANE ARE DEFINED BY THE SPHERICAL
CROWNS OF THE SOLDER BALLS.
5
BILATERAL TOLERANCE ZONE IS APPLIED
TO EACH SIDE OF THE PACKAGE BODY.
6
EXACT SHAPE AND SIZE OF THIS FEATURE
IS OPTIONAL.
0.25
1.10
0.35
0.50 BSC
e
26
0.30
MAX.
aaa
-
-
0.10
bbb
-
-
0.10
ddd
-
-
0.08
Package Diagrams
64-Pin QFNS Package
Dimensions in Millimeters
2X
A
0.15
D
C A
PIN #1 ID FIDUCIAL
LOCATED IN THIS AREA
D2
2X
0.15
N
C B
1
L
64X
3
N
1
3
PIN 1 ID
E
E2
e
B
TOP VIEW
b
0.10
M
C A B
0.50 TYP
4X
BOTTOM VIEW
VIEW A
C
VIEW A
A
SIDE VIEW
SEATING
PLANE
0.08
A3
2.
3
4
A1
MIN.
NOM.
MAX.
A
0.80
0.90
1.00
DIMENSIONS AND TOLERANCES
PER ANSI Y14.5M.
A1
0.00
0.02
0.05
A3
0.2 REF
ALL DIMENSIONS ARE IN MILLIMETERS.
D
9.0 BSC
EXACT SHAPE AND SIZE OF THIS
FEATURE IS OPTIONAL.
D2
DIMENSION b APPLIES TO PLATED
TERMINAL AND IS MEASURED BETWEEN
0.15 AND 0.30 mm FROM TERMINAL TIP.
E2
5.00
-
7.50
b
0.18
0.24
0.30
5.00
E
-
7.50
9.0 BSC
e
5
5
SYMBOL
NOTES: UNLESS OTHERWISE SPECIFIED
1.
C
0.50 BSC
APPLIES TO EXPOSED PORTION OF TERMINALS.
L
27
0.30
0.40
0.50
4
Package Diagrams
64-Ball ucBGA Package
Dimensions in Millimeters
aaa (4X)
5
6
M
e
8
7
6
5
D
PIN #1 ID FIDUCIAL
LOCATED IN THIS AREA
4
3
2
A
B
1
A
B
S
C
D
E
N
E
F
G
H
e
4X
S
6
bbb
3
A2
A
b
C
.15 M C A B
.05 M C
4
ddd
C
C
A1
NOTES: UNLESS OTHERWISE SPECIFIED
1.
DIMENSIONS AND TOLERANCES
PER ANSI Y14.5M.
2.
ALL DIMENSIONS ARE IN MILLIMETERS.
3
DIMENSION "b" IS MEASURED AT THE
MAXIMUM SOLDER BALL DIAMETER,
PARALLEL TO PRIMARY DATUM C
SYMBOL
MIN.
NOM.
A
-
-
A1
0.10
-
-
A2
-
-
0.90
D/E
4.00 BSC
M/N
2.80 BSC
S
0.20 BSC
b
4
PRIMARY DATUM C AND SEATING
PLANE ARE DEFINED BY THE SPHERICAL
CROWNS OF THE SOLDER BALLS.
5
BILATERAL TOLERANCE ZONE IS APPLIED
TO EACH SIDE OF THE PACKAGE BODY.
6
EXACT SHAPE AND SIZE OF THIS FEATURE
IS OPTIONAL.
0.20
1.00
0.30
0.40 BSC
e
28
0.25
MAX.
aaa
-
-
0.10
bbb
-
-
0.10
ddd
-
-
0.08
Package Diagrams
64-Pin TQFP Package
Dimensions in Millimeters
PIN 1 INDICATOR
0.20 C A-B
D 64X
D
3
A
MARKING
ORIENTATION
e
E1
E
B
3
D
8
D1
3
TOP VIEW
4X
0.20 H A-B
D
BOTTOM VIEW
SIDE VIEW
SEE DETAIL 'A'
b
0.08 M C A-B
D 64X
SEATING PLANE
C
A
0.08 C
1
SECTION B-B
0.20 MIN.
A1
c1
b
0.25
B
LEAD FINISH
b
c
GAUGE PLANE
H
A2
B
0-7∞
L
1.00 REF.
DETAIL 'A'
BASE METAL
NOTES:
1.
DIMENSIONING AND TOLERANCING PER ANSI Y14.5 - 1982.
2.
ALL DIMENSIONS ARE IN MILLIMETERS.
3.
DATUMS A, B AND D TO BE DETERMINED AT DATUM PLANE H.
4.
DIMENSIONS D1 AND E1 DO NOT INCLUDE MOLD PROTRUSION.
ALLOWABLE MOLD PROTRUSION IS 0.254 MM ON D1 AND E1
DIMENSIONS.
5. THE TOP OF PACKAGE MAY BE SMALLER THAN THE BOTTOM
OF THE PACKAGE BY 0.15 MM.
6.
SECTION B-B:
THESE DIMENSIONS APPLY TO THE FLAT SECTION OF THE
LEAD BETWEEN 0.10 AND 0.25 MM FROM THE LEAD TIP.
7.
A1 IS DEFINED AS THE DISTANCE FROM THE SEATING PLANE
TO THE LOWEST POINT ON THE PACKAGE BODY.
8.
EXACT SHAPE OF EACH CORNER IS OPTIONAL.
SYMBOL
MIN.
NOM.
MAX.
A
-
-
1.60
A1
0.05
-
0.15
A2
1.35
1.40
1.45
D
12.00 BSC
D1
10.00 BSC
E
12.00 BSC
E1
10.00 BSC
L
29
0.45
0.60
N
64
e
0.50 BSC
0.75
b
0.17
0.22
0.27
b1
0.17
0.20
0.23
c
0.09
-
0.20
c1
0.09
-
0.16
Package Diagrams
68-Pin JLCC Package
Dimensions in Inches
D
(N PLACES)
D1
.011 M
D2
E2
A
B
B2
L
C
L1
Q
L2
B
B
R
DETAIL A
E1
E
B1
WITH
LEAD FINISH
C
C1
BASE METAL
B
SECTION B-B
DETAIL A
A1
S
A
-A.004
Y
INCHES
M
B
O
L
SEATING
PLANE
.050
.020 MIN.
D4
E4
NOTES:
1.
DIMENSIONING AND TOLERANCING PER ANSI Y14.5M.
2.
ALL DIMENSIONS ARE IN INCHES.
3.
CORNER CHAMFERS AND/OR NOTCHES ARE OPTIONAL.
30
A
A1
B
B1
B2
C
C1
D/E
D1/E1
D2/E2
D4/E4
L
L1
L2
Q
R
N
MAX.
MIN.
.115
.190
.080 REF
.023
.013
.020
.013
.035
.022
.007
.013
.010
.007
.975 .990 1.000
.920
.960
.800 BSC
.930 BSC
.005
.020
.025
.003
.020
.040
68
Package Diagrams
68-Pin PLCC Package
Dimensions in Inches
.007
S
H A-B
S
D S
D
D1
.007
.002
-A-B-
6
S H A-B
A-B S
S D S
-D1
D3
4
PIN 1 ID ZONE
68
6
-D-
E E1
7
-A-
D3
-B-
4
4
7
E3
E3
//
7
.007
.002
.007
S
Y
M
B
O
L
A
A1
A2
D
D1
D2
D3
E
E1
E2
E3
N
S
S H A-B
A-B S
S D S
H A-B
D S
MIN. NOM. MAX.
.165
.090
.062
.985
.950
.441
.985
.950
.441
.172
.105
.990
.954
.455
.375
.990
.954
.455
.375
68
.180
.120
.083
.995
.958
.469
S
0.050
(N-4PLACES)
DETAIL "J"
D/E
.021
.013
.0105
.0075
.0125
.0075
8
A
.995
.958
.469
.018
.013
8
SECTION A-A
-H-
.004
-CSEATING PLANE
A A
D2/E2
NOTES:
ALL DIMENSIONS AND TOLERANCES CONFORM TO ANSI Y14.5M-1982
2.
ALL DIMENSIONS IN INCHES
3
-HLOCATED AT TOP OF MOLD PARTING LINE AND
DATUM PLANE
COINCIDENT WITH TOP OF LEAD WHERE LEAD EXITS PLASTIC BODY
4
TO BE DETERMINED WHERE CENTER LEADS
DATUMS A-B AND -D-HEXIT PLASTIC BODY AT DATUM PLANE
5
TO BE MEASURED AT SEATING PLANE
6
DIMENSIONS D1 AND E1 DO NOT INCLUDE MOLD PROTRUSION.
ALLOWABLE PROTRUSION IS .010 PER SIDE.
7
-H- ; BOTTOM POINT OF
TOP POINT OF MEASUREMENT IS DATUM
MEASUREMENT IS AT MAJOR FLAT AREA OF LOWER PLASTIC SURFACE
DEFINED BY D3/E3
8
DIMENSION APPLIES TO BASE METAL ONLY
-C-
.020
(MIN)
D2/E2
5
1.
3
A2
A1
5
-A-B-D-
.032
.026
.007
S
H A-B
S
D S
.045 MIN.
CONTACT POINT
.025 MIN.
-C-
SEATING PLANE
.021
.013
.007
DETAIL "J"
31
M C A-B
(TYP ALL SIDES)
S
D S
C
Package Diagrams
81-Ball csBGA Package
Dimensions in Millimeters
6
PIN #1 ID FIDUCIAL
LOCATED IN THIS AREA
M
5
aaa (4X)
D
A
B
9
8
7
6
5
4
3
2
1
e
A
B
C
D
E
E
N
F
G
H
J
e
4X
6
A2
A
b
3
bbb
.15 M C A B
.05 M C
4
ddd
C
C
C
A1
NOTES: UNLESS OTHERWISE SPECIFIED
1.
DIMENSIONS AND TOLERANCES
PER ANSI Y14.5M.
2.
ALL DIMENSIONS ARE IN MILLIMETERS.
3
DIMENSION "b" IS MEASURED AT THE
MAXIMUM SOLDER BALL DIAMETER,
PARALLEL TO PRIMARY DATUM C
4
PRIMARY DATUM C AND SEATING
PLANE ARE DEFINED BY THE SPHERICAL
CROWNS OF THE SOLDER BALLS.
5
BILATERAL TOLERANCE ZONE IS APPLIED
TO EACH SIDE OF THE PACKAGE BODY.
6
EXACT SHAPE AND SIZE OF THIS FEATURE
IS OPTIONAL.
SYMBOL
MIN.
NOM.
A
-
-
A1
0.10
-
-
A2
-
-
0.90
D/E
5.00 BSC
M/N
4.00 BSC
b
0.20
1.00
0.30
0.50 BSC
e
32
0.25
MAX.
aaa
-
-
0.10
bbb
-
-
0.10
ddd
-
-
0.10
Package Diagrams
81-Ball ucBGA Package
Dimensions in Millimeters
aaa (4X)
5
6
M
e
9
8
7
6
5
D
PIN #1 ID FIDUCIAL
LOCATED IN THIS AREA
4
3
2
A
B
1
A
B
C
D
E
N
E
F
G
H
J
e
4X
6
A2
A
b
bbb
3
C
.15 M C A B
.05 M C
4
ddd
C
C
A1
NOTES: UNLESS OTHERWISE SPECIFIED
1.
DIMENSIONS AND TOLERANCES
PER ANSI Y14.5M.
2.
ALL DIMENSIONS ARE IN MILLIMETERS.
3
DIMENSION "b" IS MEASURED AT THE
MAXIMUM SOLDER BALL DIAMETER,
PARALLEL TO PRIMARY DATUM C
SYMBOL
MIN.
NOM.
A
-
-
A1
0.10
-
-
A2
-
-
0.90
D/E
4.00 BSC
M/N
3.20 BSC
b
0.20
PRIMARY DATUM C AND SEATING
PLANE ARE DEFINED BY THE SPHERICAL
CROWNS OF THE SOLDER BALLS.
5
BILATERAL TOLERANCE ZONE IS APPLIED
TO EACH SIDE OF THE PACKAGE BODY.
6
EXACT SHAPE AND SIZE OF THIS FEATURE
IS OPTIONAL.
33
1.00
0.30
0.40 BSC
e
4
0.25
MAX.
aaa
-
-
0.10
bbb
-
-
0.10
ddd
-
-
0.10
Package Diagrams
84-Pin CPGA Package
Dimensions in Inches
.145
.070
-AD
1.180
1.140
.008
3
.30 M C A M B M
.10 M C
E
1.180
1.140
3
X
X
.100
.200
.100
-B-
.100
.075
.045
.080 MAX.
-C-
.020
.016
BASE METAL
.0215
.0165
SECTION X-X
NOTES:
1.
DIMENSIONING AND TOLERANCING PER ANSI Y14.5M.
2.
ALL DIMENSIONS ARE IN INCHES.
3.
DIMENSIONS D AND E MAY HAVE MATERIAL PROTRUSION OF
.006 INCHES MAXIMUM ABOVE THE DIMENSION SHOWN
NOT TO EXCEED .003 INCHES MAXIMUM PER SIDE.
34
SEATING PLANE
Package Diagrams
84-Pin PLCC Package
Dimensions in Inches
D1
.007
.002
-A-B-
6
S H A-B
A-B S
S D S
-D1
D3
4
PIN 1 ID ZONE
84
6
-D-
E E1
7
-A-
D3
-B-
4
4
7
E3
E3
//
7
.007
.002
.007
S
Y
M
B
O
L
A
A1
A2
D
D1
D2
D3
E
E1
E2
E3
N
S
S H A-B
A-B S
S D S
H A-B
D S
MIN. NOM. MAX.
.165
.090
.059
1.185
1.150
.541
1.185
1.150
.541
.172
.105
1.190
1.154
.555
.475
1.190
1.154
.555
.475
84
.180
.120
.080
1.195
1.158
.569
S
0.050
(N-4PLACES)
DETAIL "J"
D/E
.021
.013
.0105
.0075
.0125
.0075
1.195
1.158
.569
8
A
.018
.013
8
SECTION A-A
-H-
.004
-CSEATING PLANE
A A
D2/E2
NOTES:
ALL DIMENSIONS AND TOLERANCES CONFORM TO ANSI Y14.5M-1982
2.
ALL DIMENSIONS IN INCHES
3
-HDATUM PLANE
LOCATED AT TOP OF MOLD PARTING LINE AND
COINCIDENT WITH TOP OF LEAD WHERE LEAD EXITS PLASTIC BODY
4
TO BE DETERMINED WHERE CENTER LEADS
DATUMS A-B AND -D-HEXIT PLASTIC BODY AT DATUM PLANE
5
TO BE MEASURED AT SEATING PLANE
6
DIMENSIONS D1 AND E1 DO NOT INCLUDE MOLD PROTRUSION.
ALLOWABLE PROTRUSION IS .010 PER SIDE.
7
-H- ; BOTTOM POINT OF
TOP POINT OF MEASUREMENT IS DATUM
MEASUREMENT IS AT MAJOR FLAT AREA OF LOWER PLASTIC SURFACE
DEFINED BY D3/E3
8
DIMENSION APPLIES TO BASE METAL ONLY
-C-
.020
(MIN)
D2/E2
5
1.
3
A2
A1
5
-A-B-D-
.032
.026
.007
S
H A-B
S
D S
.045 MIN.
CONTACT POINT
.025 MIN.
-C-
SEATING PLANE
.021
.013
.007
DETAIL "J"
35
M C A-B
(TYP ALL SIDES)
S
D S
C
Package Diagrams
84-Pin QFN Package
Dimensions in Millimeters
2X
A
0.15
D
C A
0.10
2X
0.15
N
M
C A B
C B
PIN #1 ID FIDUCIAL
LOCATED IN THIS AREA
D2
A36
1
A36
B27
A1
B36
B1
B27
3
3
A48
PIN 1 ID
E
E2
B19
B9
B18
A25
B10
A24
0.10
M
A13
VIEW B
B
TOP VIEW
A12
BOTTOM VIEW
84X
VIEW A
0.10
0.05
C
M
C A B
4
C
b
e
SIDE VIEW
SEATING
PLANE
84X
0.10
M
C A B
M
g
A
L
S
0.08
A3
A1
C
VIEW B
5
f
VIEW A
SYMBOL
MIN.
NOM.
MAX.
A
0.75
0.85
0.95
A1
0.00
0.02
0.05
A3
NOTES: UNLESS OTHERWISE SPECIFIED
0.15 REF
D
7.0 BSC
1.
DIMENSIONS AND TOLERANCES
PER ANSI Y14.5M.
2.
ALL DIMENSIONS ARE IN MILLIMETERS.
E2
4.30
-
4.50
EXACT SHAPE AND SIZE OF THIS
FEATURE IS OPTIONAL.
b
0.17
0.22
0.70
e
0.50 BSC
4
DIMENSION b APPLIES TO PLATED
TERMINAL AND IS MEASURED BETWEEN
0.15 AND 0.30 mm FROM TERMINAL TIP.
f
0.50 BSC
g
0.65 BSC
5
APPLIES TO EXPOSED PORTION OF TERMINALS.
D2
4.30
E
3
4.50
7.0 BSC
S
36
-
0.25 BSC
L
0.30
0.40
0.50
M
0.30
0.40
0.50
C A B
Package Diagrams
100-Ball caBGA Package
Dimensions in Millimeters
5
(4X)
aaa
A
D
M
A1 BALL I.D.
IDENTIFIER
10
9
8
7
6
5
4
3
2
B
1
A
B
C
S
D
E
F
e
E
N
G
H
J
K
e
S
4X
b
6
A2
A
3
.15 M C A B
.08 M C
A1
bbb
ddd
C
4
C
SYMBOL
NOTES: UNLESS OTHERWISE SPECIFIED
1.
DIMENSIONS AND TOLERANCES
PER ANSI Y14.5M.
2.
ALL DIMENSIONS ARE IN MILLIMETERS.
3
DIMENSION "b" IS MEASURED AT THE
MAXIMUM SOLDER BALL DIAMETER,
PARALLEL TO PRIMARY DATUM C
4
PRIMARY DATUM C AND SEATING
PLANE ARE DEFINED BY THE SPHERICAL
CROWNS OF THE SOLDER BALLS.
5
BILATERAL TOLERANCE ZONE IS APPLIED
TO EACH SIDE OF THE PACKAGE BODY.
6
EXACT SHAPE AND SIZE OF THIS FEATURE
IS OPTIONAL.
C
MIN.
MAX.
A
1.30
1.40
1.50
A1
0.31
0.36
0.41
A2
0.99
1.04
1.09
D/E
10.00 BSC
M/N
7.20 BSC
S
0.40 BSC
b
0.40
e
37
NOM.
0.46
0.52
0.80 BSC
aaa
-
-
0.10
bbb
-
-
0.10
ddd
-
-
0.12
Package Diagrams
100-Ball csBGA Package
Dimensions in Millimeters
5
(4X)
aaa
A1 BALL I.D.
IDENTIFIER
M
D
A
B
14 13 12 11 10 9
8
7
6
5
4
3
2
1
A
B
C
D
E
S
F
G
H
N
E
J
K
L
M
N
P
e
e
6
4X
S
3
bbb
.15 M C A B
.05 M C
ddd
C
C
C
4
A1
NOTES: UNLESS OTHERWISE SPECIFIED
1.
DIMENSIONS AND TOLERANCES
PER ANSI Y14.5M.
2.
ALL DIMENSIONS ARE IN MILLIMETERS.
3
A2
A
b
DIMENSION "b" IS MEASURED AT THE
MAXIMUM SOLDER BALL DIAMETER,
PARALLEL TO PRIMARY DATUM C
SYMBOL
MIN.
A
0.90
A1
0.15
-
-
A2
-
-
1.10
PRIMARY DATUM C AND SEATING
PLANE ARE DEFINED BY THE SPHERICAL
CROWNS OF THE SOLDER BALLS.
5
BILATERAL TOLERANCE ZONE IS APPLIED
TO EACH SIDE OF THE PACKAGE BODY.
6
EXACT SHAPE AND SIZE OF THIS FEATURE
IS OPTIONAL.
8.00 BSC
M/N
6.50 BSC
S
0.25 BSC
0.25
e
38
1.23
D/E
b
4
NOM.
0.30
MAX.
1.35
0.35
0.50 BSC
aaa
-
-
0.10
bbb
-
-
0.10
ddd
-
-
0.08
Package Diagrams
100-Ball fpBGA Package
Dimensions in Millimeters
(4X)
aaa
10
9
8
7
6
A
D
M
e
5
5
4
3
2
A1 BALL I.D.
IDENTIFIER
1
B
A
B
C
D
E
N
F
E
G
S
H
J
K
e
S
4X
b
3
6
A2
A
.25 M C A B
.10 M C
bbb
ddd
C
SYMBOL
NOTES: UNLESS OTHERWISE SPECIFIED
DIMENSIONS AND TOLERANCES
PER ANSI Y14.5M.
2.
ALL DIMENSIONS ARE IN MILLIMETERS.
C
C
4
1.
A1
MIN.
3
4
PRIMARY DATUM C AND SEATING
PLANE ARE DEFINED BY THE SPHERICAL
CROWNS OF THE SOLDER BALLS.
5
BILATERAL TOLERANCE ZONE IS APPLIED
TO EACH SIDE OF THE PACKAGE BODY.
6
EXACT SHAPE AND SIZE OF THIS FEATURE
IS OPTIONAL.
A
1.30
1.50
1.70
0.30
0.50
0.70
1.10 REF
D/E
11.00 BSC
M/N
9.00 BSC
S
0.50 BSC
b
0.40
0.55
0.70
1.00 BSC
e
39
MAX.
A1
A2
DIMENSION "b" IS MEASURED AT THE
MAXIMUM SOLDER BALL DIAMETER,
PARALLEL TO PRIMARY DATUM C
NOM.
aaa
-
-
0.20
bbb
-
-
0.25
ddd
-
-
0.20
Package Diagrams
100-Pin PQFP Package
Dimensions in Millimeters
PIN 1 INDICATOR
0.25 C A-B
D 4X
E
E1
-A-
3
N
1
TOP VIEW
3
-D-
BOTTOM VIEW
D
D1
0.20 H A-B
D 4X
8
3
-B-
SEE DETAIL "A"
0.40 MIN.
e
(N-4)X
0° MIN.
SEATING
PLANE
DETAIL "A"
-H-
-CA
0.12 M
C A-B D
A2
0.13/0.30 R.
b
0.13
R. MIN.
GAGE PLANE
B
0.25
b
SECTION B - B
c
0.10 C
LEAD FINISH
B
A1
0-7°
L
1.60 REF.
c1
b1
BASE METAL
SYMBOL
MIN.
NOM.
MAX.
NOTES:
A
-
-
3.40
1.0 DIMENSIONING AND TOLERANCING PER ANSI Y14.5 - 1982.
A1
0.25
-
0.50
2.0 ALL DIMENSIONS ARE IN MILLIMETERS.
A2
2.50
2.70
2.90
3. DATUMS A, B AND D TO BE DETERMINED AT DATUM PLANE H.
4.0 DIMENSIONS D1 AND E1 DO NOT INCLUDE MOLD PROTRUSION.
ALLOWABLE MOLD PROTRUSION IS 0.254 MM ON D1 AND E1
DIMENSIONS.
5.0 THE TOP OF PACKAGE MAY BE SMALLER THAN THE BOTTOM
OF THE PACKAGE BY 0.15 MM.
D
23.20 BSC
D1
20.00 BSC
E
17.20 BSC
E1
14.00 BSC
L
0.73
N
6.0 SECTION B-B:
THESE DIMENSIONS APPLY TO THE FLAT SECTION OF THE
LEAD BETWEEN 0.10 AND 0.25 MM FROM THE LEAD TIP.
0.88
1.03
100
e
0.65 BSC
b
0.22
-
0.40
b1
0.22
0.30
0.36
8. EXACT SHAPE OF EACH CORNER IS OPTIONAL.
c
0.11
-
0.23
9. EXACT SHAPE OF EXPOSED HEATSINK IS OPTIONAL.
c1
0.11
0.15
0.19
7.0 A1 IS DEFINED AS THE DISTANCE FROM THE SEATING PLANE
TO THE LOWEST POINT ON THE PACKAGE BODY.
40
Package Diagrams
100-Pin TQFP Package Option 1: MachXO2, MachXO
Dimensions in Millimeters
0.20 C A-B
PIN 1 INDICATOR
D 100X
D
3
MARKING
ORIENTATION
A
E
E1
B
3
e
D
8
D1
3
TOP VIEW
4X
0.20 H A-B
D
BOTTOM VIEW
SIDE VIEW
SEE DETAIL 'A'
b
0.20 M C A-B
SEATING PLANE
D
C
A
0.10 C
1
SECTION B-B
0.20 MIN.
A1
c1
b
0.25
B
LEAD FINISH
b
c
GAUGE PLANE
H
A2
B
1.00 REF.
DETAIL 'A'
BASE METAL
SYMBOL
A
NOTES:
1.
DIMENSIONING AND TOLERANCING PER ANSI Y14.5 - 1982.
2.
ALL DIMENSIONS ARE IN MILLIMETERS.
3.
DATUMS A, B AND D TO BE DETERMINED AT DATUM PLANE H.
4.
DIMENSIONS D1 AND E1 DO NOT INCLUDE MOLD PROTRUSION.
ALLOWABLE MOLD PROTRUSION IS 0.254 MM ON D1 AND E1
DIMENSIONS.
MIN.
NOM.
MAX.
-
-
1.60
A1
0.05
-
0.15
A2
1.35
1.40
1.45
D
16.00 BSC
D1
14.00 BSC
E
16.00 BSC
E1
5. THE TOP OF PACKAGE MAY BE SMALLER THAN THE BOTTOM
OF THE PACKAGE BY 0.15 MM.
L
14.00 BSC
0.45
0.60
6.
SECTION B-B:
THESE DIMENSIONS APPLY TO THE FLAT SECTION OF THE
LEAD BETWEEN 0.10 AND 0.25 MM FROM THE LEAD TIP.
N
100
e
0.50 BSC
b
0.17
7.
A1 IS DEFINED AS THE DISTANCE FROM THE SEATING PLANE
TO THE LOWEST POINT ON THE PACKAGE BODY.
b1
c
c1
8.
0-7∞
L
EXACT SHAPE OF EACH CORNER IS OPTIONAL.
41
0.75
0.22
0.27
0.17
0.20
0.23
0.09
0.15
0.20
0.09
0.13
0.16
Package Diagrams
100-Pin VQFP Package Option 2: iCE40
Dimensions in Millimeters
0.20 C A-B
PIN 1 INDICATOR
D 100X
D
N
1
3
A
MARKING
ORIENTATION
E1
E
B
3
e
D
8
TOP VIEW
D1
3
4X
0.20 H A-B
D
BOTTOM VIEW
SIDE VIEW
SEE DETAIL 'A'
b
0.20 M C A-B
SEATING PLANE
D
C
A
0.08 C
c1
b
1
SECTION B-B
0.20 MIN.
A1
0-7°
1.00 REF.
DETAIL 'A'
BASE METAL
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5 - 1982.
2. ALL DIMENSIONS ARE IN MILLIMETERS.
DATUMS A, B AND D TO BE DETERMINED AT DATUM PLANE H.
4. DIMENSIONS D1 AND E1 DO NOT INCLUDE MOLD PROTRUSION.
ALLOWABLE MOLD PROTRUSION IS 0.254 MM ON D1 AND E1
DIMENSIONS.
MIN.
-
-
1.20
0.05
-
0.15
A2
0.95
1.00
1.05
D
16.00 BSC
D1
14.00 BSC
E
16.00 BSC
E1
14.00 BSC
6. SECTION B-B:
THESE DIMENSIONS APPLY TO THE FLAT SECTION OF THE
LEAD BETWEEN 0.10 AND 0.25 MM FROM THE LEAD TIP.
e
b
0.17
7. A1 IS DEFINED AS THE DISTANCE FROM THE SEATING PLANE
TO THE LOWEST POINT ON THE PACKAGE BODY.
b1
c
c1
0.45
N
42
MAX.
A1
L
EXACT SHAPE OF EACH CORNER IS OPTIONAL.
NOM.
A
5. THE TOP OF PACKAGE MAY BE SMALLER THAN THE BOTTOM
OF THE PACKAGE BY 0.15 MM.
8.
B
L
SYMBOL
3.
0.25
B
LEAD FINISH
b
c
GAUGE PLANE
H
A2
0.60
0.75
100
0.50 BSC
0.22
0.27
0.17
0.20
0.23
0.09
0.15
0.20
0.09
0.13
0.16
Package Diagrams
120-Pin PQFP Package
Dimensions in Millimeters
PIN 1 INDICATOR
0.25 C A-B
D 4X
D
D1
N
1
TOP VIEW
3
3
B
A
BOTTOM VIEW
E
E1
0.20 H A-B
D
8
3
SEE DETAIL "A"
0.20 MIN.
SEATING
PLANE
0° MIN.
e
(N-4)X
C
DETAIL "A"
H
A
A2
0.13/0.30 R.
b
0.20 M
C A-B D
0.13
R. MIN.
GAGE PLANE
B
0.25
b
SECTION B - B
D 4X
c
LEAD FINISH
0.10 C
B
A1
0-7°
L
1.60 REF.
c1
b1
BASE METAL
SYMBOL
MIN.
NOM.
MAX.
NOTES:
A
-
-
4.10
1.0 DIMENSIONING AND TOLERANCING PER ANSI Y14.5 - 1982.
A1
0.25
-
0.50
2.0 ALL DIMENSIONS ARE IN MILLIMETERS.
A2
3.20
3.40
3.60
3. DATUMS A, B AND D TO BE DETERMINED AT DATUM PLANE H.
D
31.20 BSC
4.0 DIMENSIONS D1 AND E1 DO NOT INCLUDE MOLD PROTRUSION.
ALLOWABLE MOLD PROTRUSION IS 0.254 MM ON D1 AND E1
DIMENSIONS.
D1
28.00 BSC
E
31.20 BSC
E1
5.0 THE TOP OF PACKAGE MAY BE SMALLER THAN THE BOTTOM
OF THE PACKAGE BY 0.15 MM.
L
28.00 BSC
0.73
N
6.0 SECTION B-B:
THESE DIMENSIONS APPLY TO THE FLAT SECTION OF THE
LEAD BETWEEN 0.10 AND 0.25 MM FROM THE LEAD TIP.
0.88
1.03
120
e
0.80 BSC
b
0.29
-
0.45
b1
0.29
0.35
0.41
8. EXACT SHAPE OF EACH CORNER IS OPTIONAL.
c
0.11
-
0.23
9. EXACT SHAPE OF EXPOSED HEATSINK IS OPTIONAL.
c1
0.11
0.15
0.19
7.0 A1 IS DEFINED AS THE DISTANCE FROM THE SEATING PLANE
TO THE LOWEST POINT ON THE PACKAGE BODY.
43
Package Diagrams
121-Ball csBGA Package
Dimensions in Millimeters
6
PIN #1 ID FIDUCIAL
LOCATED IN THIS AREA
M
11
10
9
8
7
6
5
4
3
2
5
aaa (4X)
D
A
1
B
A
e
B
C
D
E
N
F
E
G
H
J
K
L
e
4X
6
A2
A
b
3
bbb
.15 M C A B
.05 M C
4
ddd
C
C
C
A1
NOTES: UNLESS OTHERWISE SPECIFIED
1.
DIMENSIONS AND TOLERANCES
PER ANSI Y14.5M.
2.
ALL DIMENSIONS ARE IN MILLIMETERS.
3
DIMENSION "b" IS MEASURED AT THE
MAXIMUM SOLDER BALL DIAMETER,
PARALLEL TO PRIMARY DATUM C
SYMBOL
MIN.
NOM.
A
-
-
A1
0.10
-
-
A2
-
-
0.90
D/E
6.00 BSC
M/N
5.00 BSC
b
0.20
PRIMARY DATUM C AND SEATING
PLANE ARE DEFINED BY THE SPHERICAL
CROWNS OF THE SOLDER BALLS.
5
BILATERAL TOLERANCE ZONE IS APPLIED
TO EACH SIDE OF THE PACKAGE BODY.
6
EXACT SHAPE AND SIZE OF THIS FEATURE
IS OPTIONAL.
44
1.00
0.30
0.50 BSC
e
4
0.25
MAX.
aaa
-
-
0.10
bbb
-
-
0.10
ddd
-
-
0.10
Package Diagrams
121-Ball ucBGA Package
Dimensions in Millimeters
6
PIN #1 ID FIDUCIAL
LOCATED IN THIS AREA
M
5
aaa (4X)
D
A
B
11 10 9
e
8
7
6
5
4
3
2
1
A
B
C
D
E
F
E
N
G
H
J
K
L
e
4X
6
A2
A
b
3
bbb
.15 M C A B
.05 M C
4
ddd
C
C
C
A1
NOTES: UNLESS OTHERWISE SPECIFIED
1.
DIMENSIONS AND TOLERANCES
PER ANSI Y14.5M.
2.
ALL DIMENSIONS ARE IN MILLIMETERS.
3
DIMENSION "b" IS MEASURED AT THE
MAXIMUM SOLDER BALL DIAMETER,
PARALLEL TO PRIMARY DATUM C
4
PRIMARY DATUM C AND SEATING
PLANE ARE DEFINED BY THE SPHERICAL
CROWNS OF THE SOLDER BALLS.
5
BILATERAL TOLERANCE ZONE IS APPLIED
TO EACH SIDE OF THE PACKAGE BODY.
6
EXACT SHAPE AND SIZE OF THIS FEATURE
IS OPTIONAL.
SYMBOL
MIN.
NOM.
A
-
-
A1
0.10
-
-
A2
-
-
0.90
D/E
5.00 BSC
M/N
4.00 BSC
b
0.20
1.00
0.30
0.40 BSC
e
45
0.25
MAX.
aaa
-
-
0.10
bbb
-
-
0.10
ddd
-
-
0.10
Package Diagrams
128-Pin PQFP Package
Dimensions in Millimeters
PIN 1 INDICATOR
0.25 C A-B
D 4X
D
D1
N
1
TOP VIEW
3
3
B
A
BOTTOM VIEW
E
E1
0.20 H A-B
D
8
3
SEE DETAIL "A"
0.20 MIN.
SEATING
PLANE
0° MIN.
e
(N-4)X
C
DETAIL "A"
H
A
A2
0.13/0.30 R.
b
0.20 M
C A-B D
0.13
R. MIN.
GAGE PLANE
B
0.25
b
SECTION B - B
D 4X
c
LEAD FINISH
0.10 C
B
A1
L
1.60 REF.
c1
0-7°
b1
BASE METAL
SYMBOL
MIN.
NOM.
MAX.
NOTES:
A
-
-
4.10
1.0 DIMENSIONING AND TOLERANCING PER ANSI Y14.5 - 1982.
A1
0.25
-
0.50
2.0 ALL DIMENSIONS ARE IN MILLIMETERS.
A2
3.20
3.40
3.60
3. DATUMS A, B AND D TO BE DETERMINED AT DATUM PLANE H.
D
31.20 BSC
4.0 DIMENSIONS D1 AND E1 DO NOT INCLUDE MOLD PROTRUSION.
ALLOWABLE MOLD PROTRUSION IS 0.254 MM ON D1 AND E1
DIMENSIONS.
D1
28.00 BSC
E
31.20 BSC
E1
5.0 THE TOP OF PACKAGE MAY BE SMALLER THAN THE BOTTOM
OF THE PACKAGE BY 0.15 MM.
L
28.00 BSC
0.73
N
6.0 SECTION B-B:
THESE DIMENSIONS APPLY TO THE FLAT SECTION OF THE
LEAD BETWEEN 0.10 AND 0.25 MM FROM THE LEAD TIP.
0.88
1.03
128
e
0.80 BSC
b
0.29
-
0.45
b1
0.29
0.35
0.41
8. EXACT SHAPE OF EACH CORNER IS OPTIONAL.
c
0.11
-
0.23
9. EXACT SHAPE OF EXPOSED HEATSINK IS OPTIONAL.
c1
0.11
0.15
0.19
7.0 A1 IS DEFINED AS THE DISTANCE FROM THE SEATING PLANE
TO THE LOWEST POINT ON THE PACKAGE BODY.
46
Package Diagrams
128-Pin TQFP Package
Dimensions in Millimeters
PIN 1 INDICATOR
0.20 C A-B
D
D
D1
0.20 H A-B D
N
1
3. A
e
MARKING
ORIENTAION
B
D
E1
E
3.
3.
8. 4X
SEE DETAIL "A"
H
b
0.07
M C A -B D
C
A
SEATING PLANE
B
0.08 C
A1
LEAD FINISH
b
GAUGE PLANE
0.25
A2
B
0.20 MIN.
0-7∞
L
1.00 REF.
c
c1
b
DETAIL "A"
1
BASE METAL
SECTION B - B
NOTES:
1.
DIMENSIONING AND TOLERANCING PER ANSI Y14.5 - 1982.
2.
ALL DIMENSIONS ARE IN MILLIMETERS.
3.
DATUMS A, B AND D TO BE DETERMINED AT DATUM PLANE H.
4.
DIMENSIONS D1 AND E1 DO NOT INCLUDE MOLD PROTRUSION.
ALLOWABLE MOLD PROTRUSION IS 0.254 MM ON D1 AND E1
DIMENSIONS.
A1 IS DEFINED AS THE DISTANCE FROM THE SEATING PLANE
TO THE LOWEST POINT ON THE PACKAGE BODY.
8.
EXACT SHAPE OF EACH CORNER IS OPTIONAL.
NOM.
MAX.
-
-
1.60
A1
0.05
-
0.15
A2
1.35
1.40
1.45
D
16.00 BSC
D1
14.00 BSC
E
16.00 BSC
L
SECTION B-B:
THESE DIMENSIONS APPLY TO THE FLAT SECTION OF THE
LEAD BETWEEN 0.10 AND 0.25 MM FROM THE LEAD TIP.
7.
MIN.
A
E1
5. THE TOP OF PACKAGE MAY BE SMALLER THAN THE BOTTOM
OF THE PACKAGE BY 0.15 MM.
6.
SYMBOL
47
14.00 BSC
0.45
0.60
N
128
e
0.40 BSC
0.75
b
0.13
b1
0.13
0.16
0.19
c
0.09
0.15
0.20
c1
0.09
0.13
0.16
0.18
0.23
Package Diagrams
132-Ball csBGA Package Option 1: MachXO2, MachXO, LatticeXP2
Dimensions in Millimeters
5
(4X)
aaa
A1 BALL I.D.
IDENTIFIER
M
D
A
B
14 13 12 11 10 9
8
7
6
5
4
3
2
1
A
B
C
D
E
S
F
G
H
N
E
J
K
L
M
N
P
e
e
6
4X
S
3
bbb
.15 M C A B
.05 M C
ddd
C
C
C
4
A1
NOTES: UNLESS OTHERWISE SPECIFIED
1.
DIMENSIONS AND TOLERANCES
PER ANSI Y14.5M.
2.
ALL DIMENSIONS ARE IN MILLIMETERS.
3
A2
A
b
DIMENSION "b" IS MEASURED AT THE
MAXIMUM SOLDER BALL DIAMETER,
PARALLEL TO PRIMARY DATUM C
PRIMARY DATUM C AND SEATING
PLANE ARE DEFINED BY THE SPHERICAL
CROWNS OF THE SOLDER BALLS.
5
BILATERAL TOLERANCE ZONE IS APPLIED
TO EACH SIDE OF THE PACKAGE BODY.
6
EXACT SHAPE AND SIZE OF THIS FEATURE
IS OPTIONAL.
A
0.90
A1
0.15
-
-
A2
-
-
1.10
1.23
D/E
8.00 BSC
M/N
6.50 BSC
S
0.25 BSC
0.25
0.30
1.35
0.35
0.50 BSC
e
48
MAX.
MIN.
b
4
NOM.
SYMBOL
aaa
-
-
0.10
bbb
-
-
0.10
ddd
-
-
0.08
Package Diagrams
132-Ball csBGA Package Option 2: iCE40
Dimensions in Millimeters
5
(4X)
aaa
A1 BALL I.D.
IDENTIFIER
M
D
A
B
14 13 12 11 10 9
8
7
6
5
4
3
2
1
A
B
C
D
E
S
F
G
H
N
E
J
K
L
M
N
P
e
e
6
4X
S
3
bbb
.15 M C A B
.08 M C
ddd
C
C
C
4
A1
NOTES: UNLESS OTHERWISE SPECIFIED
1.
DIMENSIONS AND TOLERANCES
PER ANSI Y14.5M.
2.
ALL DIMENSIONS ARE IN MILLIMETERS.
3
A2
A
b
DIMENSION "b" IS MEASURED AT THE
MAXIMUM SOLDER BALL DIAMETER,
PARALLEL TO PRIMARY DATUM C
MIN.
NOM.
A
-
-
A1
0.15
-
-
A2
-
-
0.85
D/E
8.00 BSC
M/N
6.50 BSC
S
0.25 BSC
b
4
PRIMARY DATUM C AND SEATING
PLANE ARE DEFINED BY THE SPHERICAL
CROWNS OF THE SOLDER BALLS.
5
BILATERAL TOLERANCE ZONE IS APPLIED
TO EACH SIDE OF THE PACKAGE BODY.
6
EXACT SHAPE AND SIZE OF THIS FEATURE
IS OPTIONAL.
0.25
0.30
1.00
0.35
0.50 BSC
e
49
MAX.
SYMBOL
aaa
-
-
0.10
bbb
-
-
0.10
ddd
-
-
0.08
Package Diagrams
132-Ball ucBGA Package
Dimensions in Millimeters
PIN #1 ID FIDUCIAL
LOCATED IN THIS AREA
M
5
aaa (4X)
6
D
A
B
12 11 10 9
e
8
7
6
5
4
3
2
1
A
B
C
D
S
E
F
E
N
G
H
J
K
L
M
e
S
6
4X
b
A2
A
3
bbb
.15 M C A B
.05 M C
4
ddd
C
C
C
A1
NOTES: UNLESS OTHERWISE SPECIFIED
1.
DIMENSIONS AND TOLERANCES
PER ANSI Y14.5M.
2.
ALL DIMENSIONS ARE IN MILLIMETERS.
3
DIMENSION "b" IS MEASURED AT THE
MAXIMUM SOLDER BALL DIAMETER,
PARALLEL TO PRIMARY DATUM C
4
PRIMARY DATUM C AND SEATING
PLANE ARE DEFINED BY THE SPHERICAL
CROWNS OF THE SOLDER BALLS.
5
BILATERAL TOLERANCE ZONE IS APPLIED
TO EACH SIDE OF THE PACKAGE BODY.
6
EXACT SHAPE AND SIZE OF THIS FEATURE
IS OPTIONAL.
SYMBOL
MIN.
NOM.
A
-
-
A1
0.10
-
-
A2
-
-
0.90
D/E
6.00 BSC
M/N
4.40 BSC
S
0.20 BSC
b
0.20
1.00
0.30
0.40 BSC
e
50
0.25
MAX.
aaa
-
-
0.10
bbb
-
-
0.10
ddd
-
-
0.08
Package Diagrams
133-Pin CPGA Package
Dimensions in Inches
.145
.070
-A-
D
1.480
1.440
.008
3
.30 M C A M B M
.10 M C
.050
E
1.480
1.440
3
X
X
.100
.200
.100
.050
-B-
.100
.075
.045
.080 MAX.
SEATING PLANE
-C-
.020
.016
BASE METAL
.0215
.0165
SECTION X-X
NOTES:
1.
DIMENSIONING AND TOLERANCING PER ANSI Y14.5M.
2.
ALL DIMENSIONS ARE IN INCHES.
3.
DIMENSIONS D AND E MAY HAVE MATERIAL PROTRUSION OF
.006 INCHES MAXIMUM ABOVE THE DIMENSION SHOWN
NOT TO EXCEED .003 INCHES MAXIMUM PER SIDE.
51
Package Diagrams
144-Ball csBGA Package
Dimensions in Millimeters
PIN #1 ID FIDUCIAL
LOCATED IN THIS AREA
M
5
aaa (4X)
6
D
A
B
12 11 10 9
8
7
6
5
4
3
2
1
A
e
B
C
D
E
F
S
E
N
G
H
J
K
L
M
e
6
4X
S
b
3
A2
A
bbb
.15 M C A B
.05 M C
4
ddd
C
C
C
A1
NOTES: UNLESS OTHERWISE SPECIFIED
1.
DIMENSIONS AND TOLERANCES
PER ANSI Y14.5M.
2.
ALL DIMENSIONS ARE IN MILLIMETERS.
3
DIMENSION "b" IS MEASURED AT THE
MAXIMUM SOLDER BALL DIAMETER,
PARALLEL TO PRIMARY DATUM C
MIN.
A
0.90
A1
0.15
-
-
A2
-
-
0.85
PRIMARY DATUM C AND SEATING
PLANE ARE DEFINED BY THE SPHERICAL
CROWNS OF THE SOLDER BALLS.
5
BILATERAL TOLERANCE ZONE IS APPLIED
TO EACH SIDE OF THE PACKAGE BODY.
6
EXACT SHAPE AND SIZE OF THIS FEATURE
IS OPTIONAL.
7.00 BSC
M/N
5.50 BSC
S
0.25 BSC
0.25
0.30
MAX.
1.10
0.35
0.50 BSC
e
52
1.00
D/E
b
4
NOM.
SYMBOL
aaa
-
-
0.10
bbb
-
-
0.10
ddd
-
-
0.08
Package Diagrams
144-Ball fpBGA Package
Dimensions in Millimeters
A1 CORNER
INDEX AREA
5
aaa
(4X)
A
D
M
B
B
12 11 10
9
8
7
6
5
4
3
2
1
A
B
S
C
D
E
F
N
G
E
C
H
J
K
L
M
e
e
S
3
6
4X
b
A
.25 M C A B
.10 M C
ccc
bbb
ddd
A2
A1
C
C
C
4
C
NOTES: UNLESS OTHERWISE SPECIFIED
SYMBOL
1.
2.
3
4
MIN.
NOM.
MAX.
DIMENSIONS AND TOLERANCES
PER ANSI Y14.5M.
A
1.30
1.70
2.10
A1
0.30
0.50
0.70
ALL DIMENSIONS ARE IN MILLIMETERS.
A2
0.30
0.50
0.70
B/C
11.00
11.60
12.20
DIMENSION "b" IS MEASURED AT THE
MAXIMUM SOLDER BALL DIAMETER,
PARALLEL TO PRIMARY DATUM C
D/E
13.00 BSC
M/N
11.00 BSC
0.50 BSC
S
PRIMARY DATUM C AND SEATING
PLANE ARE DEFINED BY THE SPHERICAL
CROWNS OF THE SOLDER BALLS.
b
0.50
e
5
BILATERAL TOLERANCE ZONE IS APPLIED
TO EACH SIDE OF THE PACKAGE BODY.
6
EXACT SHAPE AND SIZE OF THIS FEATURE
IS OPTIONAL.
53
0.60
0.70
1.00 BSC
aaa
-
-
0.20
bbb
-
-
0.25
ccc
-
-
0.35
ddd
-
-
0.20
Package Diagrams
144-Pin TQFP Package
Dimensions in Millimeters
PIN 1 INDICATOR
0.20 C A-B
D
D
D1
0.20 H A-B D
N
1
3. A
e
MARKING
ORIENTATION
B
D
E1
E
3.
3.
8. 4X
SEE DETAIL "A"
H
b
0.08
M C A -B D
C
A
SEATING PLANE
B
0.08 C
A1
LEAD FINISH
b
GAUGE PLANE
0.25
A2
B
0.20 MIN.
0-7∞
L
1.00 REF.
c
c1
DETAIL "A"
b
1
BASE METAL
SECTION B - B
SYMBOL
A
NOTES:
1.
DIMENSIONING AND TOLERANCING PER ANSI Y14.5 - 1982.
2.
ALL DIMENSIONS ARE IN MILLIMETERS.
3.
DATUMS A, B AND D TO BE DETERMINED AT DATUM PLANE H.
4.
DIMENSIONS D1 AND E1 DO NOT INCLUDE MOLD PROTRUSION.
ALLOWABLE MOLD PROTRUSION IS 0.254 MM ON D1 AND E1
DIMENSIONS.
6.
7.
8.
SECTION B-B:
THESE DIMENSIONS APPLY TO THE FLAT SECTION OF THE
LEAD BETWEEN 0.10 AND 0.25 MM FROM THE LEAD TIP.
A1 IS DEFINED AS THE DISTANCE FROM THE SEATING PLANE
TO THE LOWEST POINT ON THE PACKAGE BODY.
EXACT SHAPE OF EACH CORNER IS OPTIONAL.
54
NOM.
MAX.
-
-
1.60
A1
0.05
-
0.15
A2
1.35
1.40
1.45
D
22.00 BSC
D1
20.00 BSC
E
22.00 BSC
E1
20.00 BSC
L
5. THE TOP OF PACKAGE MAY BE SMALLER THAN THE BOTTOM
OF THE PACKAGE BY 0.15 MM.
MIN.
0.45
0.60
N
144
e
0.50 BSC
0.75
b
0.17
0.22
0.27
b1
0.17
0.20
0.23
c
0.09
0.15
0.20
c1
0.09
0.13
0.16
Package Diagrams
160-Pin PQFP Package
Dimensions in Millimeters
PIN 1 INDICATOR
0.25 C A-B
D 4X
D
D1
N
1
TOP VIEW
3
3
B
A
BOTTOM VIEW
E
E1
0.20 H A-B
D
8
3
SEE DETAIL "A"
0.20 MIN.
SEATING
PLANE
0° MIN.
e
(N-4)X
C
DETAIL "A"
H
A
A2
0.13/0.30 R.
b
0.13 M
C A-B D
0.13
R. MIN.
GAGE PLANE
B
0.25
b
SECTION B - B
D 4X
c
LEAD FINISH
0.10 C
B
A1
0-7°
L
1.60 REF.
c1
b1
BASE METAL
SYMBOL
MIN.
NOM.
MAX.
NOTES:
A
-
-
4.10
1.0 DIMENSIONING AND TOLERANCING PER ANSI Y14.5 - 1982.
A1
0.25
-
0.50
2.0 ALL DIMENSIONS ARE IN MILLIMETERS.
A2
3.20
3.40
3.60
3. DATUMS A, B AND D TO BE DETERMINED AT DATUM PLANE H.
D
31.20 BSC
4.0 DIMENSIONS D1 AND E1 DO NOT INCLUDE MOLD PROTRUSION.
ALLOWABLE MOLD PROTRUSION IS 0.254 MM ON D1 AND E1
DIMENSIONS.
D1
28.00 BSC
E
31.20 BSC
E1
5.0 THE TOP OF PACKAGE MAY BE SMALLER THAN THE BOTTOM
OF THE PACKAGE BY 0.15 MM.
L
28.00 BSC
0.73
N
6.0 SECTION B-B:
THESE DIMENSIONS APPLY TO THE FLAT SECTION OF THE
LEAD BETWEEN 0.10 AND 0.25 MM FROM THE LEAD TIP.
0.88
1.03
160
e
0.65 BSC
b
0.22
-
0.40
b1
0.22
0.30
0.36
8. EXACT SHAPE OF EACH CORNER IS OPTIONAL.
c
0.11
-
0.23
9. EXACT SHAPE OF EXPOSED HEATSINK IS OPTIONAL.
c1
0.11
0.15
0.19
7.0 A1 IS DEFINED AS THE DISTANCE FROM THE SEATING PLANE
TO THE LOWEST POINT ON THE PACKAGE BODY.
55
Package Diagrams
176-Pin TQFP Package
Dimensions in Millimeters
PIN 1 INDICATOR
0.20 C A-B
D
D
D1
0.20 H A-B D
N
1
3. A
e
MARKING
ORIENTATION
B
D
E1
E
3.
3.
SEE DETAIL "A"
8. 4X
H
b
0.08
M C A -B D
C
SEATING PLANE
GAUGE PLANE
0.25
A2
B
0.08 C
LEAD FINISH
b
A
A1
B
0.20 MIN.
0-7∞
L
1.00 REF.
c
c1
b
DETAIL "A"
1
BASE METAL
SECTION B - B
NOTES:
SYMBOL
MIN.
NOM.
MAX.
A
-
-
1.60
A1
0.05
-
0.15
1.35
1.40
1.45
1.
DIMENSIONING AND TOLERANCING PER ANSI Y14.5 - 1982.
A2
2.
ALL DIMENSIONS ARE IN MILLIMETERS.
D
26.00 BSC
3.
DATUMS A, B AND D TO BE DETERMINED AT DATUM PLANE H.
D1
24.00 BSC
4.
DIMENSIONS D1 AND E1 DO NOT INCLUDE MOLD PROTRUSION.
ALLOWABLE MOLD PROTRUSION IS 0.254 MM ON D1 AND E1
DIMENSIONS.
E
26.00 BSC
E1
24.00 BSC
L
5. THE TOP OF PACKAGE MAY BE SMALLER THAN THE BOTTOM
OF THE PACKAGE BY 0.15 MM.
6.
7.
8.
SECTION B-B:
THESE DIMENSIONS APPLY TO THE FLAT SECTION OF THE
LEAD BETWEEN 0.10 AND 0.25 MM FROM THE LEAD TIP.
A1 IS DEFINED AS THE DISTANCE FROM THE SEATING PLANE
TO THE LOWEST POINT ON THE PACKAGE BODY.
EXACT SHAPE OF EACH CORNER IS OPTIONAL.
56
0.45
0.60
N
176
e
0.50 BSC
0.22
0.75
b
0.17
0.27
b1
0.17
0.20
0.23
c
0.09
0.15
0.20
c1
0.09
0.13
0.16
Package Diagrams
184-Ball csBGA Package
Dimensions in Millimeters
5
aaa
A1 BALL I.D.
IDENTIFIER
M
(4X)
D
A
B
S
N
E
e
e
6
4X
S
3
A2
A
b
bbb C
.15 M C A B
.05 M C
ddd C
C
4
A1
SYMBOL
A
A1
NOTES: UNLESS OTHERWISE SPECIFIED
1.
DIMENSIONS AND TOLERANCES
PER ANSI Y14.5M.
2.
ALL DIMENSIONS ARE IN MILLIMETERS.
A2
3
DIMENSION "b" IS MEASURED AT THE
MAXIMUM SOLDER BALL DIAMETER,
PARALLEL TO PRIMARY DATUM C
4
PRIMARY DATUM C AND SEATING
PLANE ARE DEFINED BY THE SPHERICAL
CROWNS OF THE SOLDER BALLS.
5
BILATERAL TOLERANCE ZONE IS APPLIED
TO EACH SIDE OF THE PACKAGE BODY.
6
EXACT SHAPE AND SIZE OF THIS FEATURE
IS OPTIONAL.
MIN.
1.20
0.16
-
D/E
8.00 BSC
M/N
6.50 BSC
S
0.25 BSC
b
0.25
e
57
NOM.
1.35
-
0.30
MAX.
1.50
1.34
0.35
0.50 BSC
aaa
-
-
0.10
bbb
-
-
0.10
ddd
-
-
0.08
Package Diagrams
196-Ball csBGA Package
Dimensions in Millimeters
5
(4X)
aaa
A1 BALL I.D.
IDENTIFIER
M
D
A
B
14 13 12 11 10 9
8
7
6
5
4
3
2
1
A
B
C
D
E
S
F
G
H
N
E
J
K
L
M
N
P
e
e
6
4X
S
3
bbb
.15 M C A B
.08 M C
ddd
C
C
C
4
A1
NOTES: UNLESS OTHERWISE SPECIFIED
1.
DIMENSIONS AND TOLERANCES
PER ANSI Y14.5M.
2.
ALL DIMENSIONS ARE IN MILLIMETERS.
3
A2
A
b
DIMENSION "b" IS MEASURED AT THE
MAXIMUM SOLDER BALL DIAMETER,
PARALLEL TO PRIMARY DATUM C
MIN.
NOM.
A
-
-
A1
0.15
-
-
A2
-
-
0.85
D/E
8.00 BSC
M/N
6.50 BSC
S
0.25 BSC
b
4
PRIMARY DATUM C AND SEATING
PLANE ARE DEFINED BY THE SPHERICAL
CROWNS OF THE SOLDER BALLS.
5
BILATERAL TOLERANCE ZONE IS APPLIED
TO EACH SIDE OF THE PACKAGE BODY.
6
EXACT SHAPE AND SIZE OF THIS FEATURE
IS OPTIONAL.
0.25
0.30
1.00
0.35
0.50 BSC
e
58
MAX.
SYMBOL
aaa
-
-
0.10
bbb
-
-
0.10
ddd
-
-
0.08
Package Diagrams
208-Ball ftBGA Package
Dimensions in Millimeters
5
(4X)
A1 BALL I.D.
IDENTIFIER
M
16
14
15
12
13
10
11
8
9
aaa
6
7
4
5
D
A
2
3
B
1
A
B
C
D
E
F
S
G
H
J
N
E
K
L
M
N
P
R
T
e
e
6
4X
S
b
3
bbb
ddd
C
C
C
4
A1
NOTES: UNLESS OTHERWISE SPECIFIED
1.
DIMENSIONS AND TOLERANCES
PER ANSI Y14.5M.
2.
ALL DIMENSIONS ARE IN MILLIMETERS.
3
A2
A
.25 M C A B
.10 M C
DIMENSION "b" IS MEASURED AT THE
MAXIMUM SOLDER BALL DIAMETER,
PARALLEL TO PRIMARY DATUM C
MIN.
A
1.25
A1
0.30
-
-
A2
-
-
1.25
PRIMARY DATUM C AND SEATING
PLANE ARE DEFINED BY THE SPHERICAL
CROWNS OF THE SOLDER BALLS.
5
BILATERAL TOLERANCE ZONE IS APPLIED
TO EACH SIDE OF THE PACKAGE BODY.
6
EXACT SHAPE AND SIZE OF THIS FEATURE
IS OPTIONAL.
1.40
17.0 BSC
M/N
15.0 BSC
S
0.50 BSC
0.40
0.50
1.55
0.60
1.0 BSC
e
59
NOM.
D/E
b
4
MAX.
SYMBOL
aaa
-
-
0.20
bbb
-
-
0.25
ddd
-
-
0.12
Package Diagrams
208-Ball fpBGA Package
Dimensions in Millimeters
A1 CORNER
INDEX AREA
5
aaa
(4X)
A
D
M
B
B
16 15 14 13 12 11 10
9
8
7
6
5
4
3
2
1
A
B
C
D
S
E
F
G
H
E
C
N
J
K
L
M
N
P
R
T
e
e
S
3
A
.25 M C A B
.10 M C
A2
A1
ccc
bbb
ddd
C
C
C
4
C
SYMBOL
NOTES: UNLESS OTHERWISE SPECIFIED
1.
DIMENSIONS AND TOLERANCES
PER ANSI Y14.5M.
2.
ALL DIMENSIONS ARE IN MILLIMETERS.
3
6
4X
b
DIMENSION "b" IS MEASURED AT THE
MAXIMUM SOLDER BALL DIAMETER,
PARALLEL TO PRIMARY DATUM C
4
PRIMARY DATUM C AND SEATING
PLANE ARE DEFINED BY THE SPHERICAL
CROWNS OF THE SOLDER BALLS.
5
BILATERAL TOLERANCE ZONE IS APPLIED
TO EACH SIDE OF THE PACKAGE BODY.
6
EXACT SHAPE AND SIZE OF THIS FEATURE
IS OPTIONAL.
MIN.
MAX.
A
1.30
1.70
2.10
A1
0.30
0.50
0.70
A2
0.30
0.50
0.70
B/C
14.80
15.30
15.80
D/E
17.00 BSC
M/N
15.00 BSC
S
b
0.50 BSC
0.50
e
60
NOM.
0.60
0.70
1.00 BSC
aaa
-
-
0.20
bbb
-
-
0.25
ccc
-
-
0.35
ddd
-
-
0.20
Package Diagrams
208-Pin PQFP Package
Dimensions in Millimeters
PIN 1 INDICATOR
0.25 C A-B
D 4X
D
D1
N
1
TOP VIEW
3
3
B
A
BOTTOM VIEW
E
E1
0.20 H A-B
D
8
3
SEE DETAIL "A"
0.20 MIN.
SEATING
PLANE
0° MIN.
e
(N-4)X
C
DETAIL "A"
H
A
A2
0.08/0.25 R.
b
0.08 M
C A-B D
0.08
R. MIN.
GAGE PLANE
B
0.25
b
SECTION B - B
D 4X
c
LEAD FINISH
0.08 C
B
A1
0-8°
L
1.30 REF.
c1
b1
BASE METAL
SYMBOL
MIN.
NOM.
MAX.
NOTES:
A
-
-
4.10
1.0 DIMENSIONING AND TOLERANCING PER ANSI Y14.5 - 1982.
A1
0.25
-
0.50
2.0 ALL DIMENSIONS ARE IN MILLIMETERS.
A2
3.20
3.40
3.60
3. DATUMS A, B AND D TO BE DETERMINED AT DATUM PLANE H.
D
30.60 BSC
4.0 DIMENSIONS D1 AND E1 DO NOT INCLUDE MOLD PROTRUSION.
ALLOWABLE MOLD PROTRUSION IS 0.254 MM ON D1 AND E1
DIMENSIONS.
D1
28.00 BSC
E
30.60 BSC
E1
5.0 THE TOP OF PACKAGE MAY BE SMALLER THAN THE BOTTOM
OF THE PACKAGE BY 0.15 MM.
L
6.0 SECTION B-B:
THESE DIMENSIONS APPLY TO THE FLAT SECTION OF THE
LEAD BETWEEN 0.10 AND 0.25 MM FROM THE LEAD TIP.
28.00 BSC
0.45
0.60
N
208
e
0.50 BSC
0.75
b
0.17
-
0.27
b1
0.17
0.20
0.23
8. EXACT SHAPE OF EACH CORNER IS OPTIONAL.
c
0.09
-
0.20
9. EXACT SHAPE OF EXPOSED HEATSINK IS OPTIONAL.
c1
0.09
0.12
0.16
7.0 A1 IS DEFINED AS THE DISTANCE FROM THE SEATING PLANE
TO THE LOWEST POINT ON THE PACKAGE BODY.
61
Package Diagrams
225-Ball ucBGA Package
Dimensions in Millimeters
aaa (4X)
6
PIN #1 ID FIDUCIAL
LOCATED IN THIS AREA
M
5
D
A
B
15 14 13 12 11 10 9
8
7
6
5
4
3
1
2
A
e
B
C
D
E
F
G
E
N
H
J
K
L
M
N
P
R
e
4X
6
b
3
A2
A
.15 M C A B
.05 M C
C
bbb
4
ddd
C
C
A1
NOTES: UNLESS OTHERWISE SPECIFIED
1.
DIMENSIONS AND TOLERANCES
PER ANSI Y14.5M.
2.
ALL DIMENSIONS ARE IN MILLIMETERS.
3
DIMENSION "b" IS MEASURED AT THE
MAXIMUM SOLDER BALL DIAMETER,
PARALLEL TO PRIMARY DATUM C
SYMBOL
MIN.
NOM.
A
-
-
A1
0.10
-
-
A2
-
-
0.90
D/E
7.00 BSC
M/N
5.60 BSC
b
0.20
PRIMARY DATUM C AND SEATING
PLANE ARE DEFINED BY THE SPHERICAL
CROWNS OF THE SOLDER BALLS.
5
BILATERAL TOLERANCE ZONE IS APPLIED
TO EACH SIDE OF THE PACKAGE BODY.
6
EXACT SHAPE AND SIZE OF THIS FEATURE
IS OPTIONAL.
62
1.00
0.30
0.40 BSC
e
4
0.25
MAX.
aaa
-
-
0.10
bbb
-
-
0.10
ddd
-
-
0.10
Package Diagrams
256-Ball caBGA Package
Dimensions in Millimeters
5
(4X)
A1 CORNER
INDEX AREA
M
16
14
15
12
13
10
11
8
9
aaa
6
7
4
5
D
A
2
3
B
1
A
B
C
D
E
F
S
G
H
J
N
E
K
L
M
N
P
R
T
e
e
4X
S
6
b
A2
A
3
.15 M C A B
.08 M C
bbb
ddd
C
C
C
4
A1
NOTES: UNLESS OTHERWISE SPECIFIED
A
MIN.
-
NOM.
-
A1
0.25
-
-
A2
0.65
-
-
SYMBOL
1.
DIMENSIONS AND TOLERANCES
PER ANSI Y14.5M.
2.
ALL DIMENSIONS ARE IN MILLIMETERS.
3
DIMENSION "b" IS MEASURED AT THE
MAXIMUM SOLDER BALL DIAMETER,
PARALLEL TO PRIMARY DATUM C
4
PRIMARY DATUM C AND SEATING
PLANE ARE DEFINED BY THE SPHERICAL
CROWNS OF THE SOLDER BALLS.
5
BILATERAL TOLERANCE ZONE IS APPLIED
TO EACH SIDE OF THE PACKAGE BODY.
6
EXACT SHAPE AND SIZE OF THIS FEATURE
IS OPTIONAL.
7.
REFERENCE JEDEC MO-275, VARIATION JJAB-2.
D/E
14.0 BSC
M/N
12.0 BSC
S
0.40 BSC
b
0.40
0.50
0.80 BSC
e
63
0.45
MAX.
1.70
aaa
-
-
0.15
bbb
-
-
0.20
ddd
-
-
0.20
Package Diagrams
256-Ball ftBGA Package Option 1: ispMACH 4000, MachXO, LatticeXP2
Dimensions in Millimeters
5
(4X)
16
14
15
12
13
10
11
8
9
aaa
A1 BALL I.D.
IDENTIFIER
M
6
7
4
5
D
A
2
3
B
1
A
B
C
D
E
F
S
G
H
J
N
E
K
L
M
N
P
R
T
e
e
6
4X
S
b
A2
A
3
.25 M C A B
.10 M C
bbb
ddd
C
C
4
C
A1
SYMBOL
NOTES: UNLESS OTHERWISE SPECIFIED
1.
DIMENSIONS AND TOLERANCES
PER ANSI Y14.5M.
2.
ALL DIMENSIONS ARE IN MILLIMETERS.
3
DIMENSION "b" IS MEASURED AT THE
MAXIMUM SOLDER BALL DIAMETER,
PARALLEL TO PRIMARY DATUM C
4
PRIMARY DATUM C AND SEATING
PLANE ARE DEFINED BY THE SPHERICAL
CROWNS OF THE SOLDER BALLS.
5
BILATERAL TOLERANCE ZONE IS APPLIED
TO EACH SIDE OF THE PACKAGE BODY.
6
EXACT SHAPE AND SIZE OF THIS FEATURE
IS OPTIONAL.
MIN.
A
1.25
A1
0.30
-
A2
-
-
1.40
D/E
17.0 BSC
M/N
15.0 BSC
S
0.50 BSC
b
0.40
e
64
NOM.
0.50
MAX.
1.55
1.25
0.60
1.00 BSC
aaa
-
-
0.20
bbb
-
-
0.25
ddd
-
-
0.12
Package Diagrams
256-Ball ftBGA Package Option 2: LatticeECP3
Dimensions in Millimeters
5
(4X)
16
14
15
12
13
10
11
8
9
aaa
A1 CORNER
INDEX AREA
M
6
7
4
5
D
A
2
3
B
1
A
B
C
D
E
F
S
G
H
J
N
E
K
L
M
N
P
R
T
e
e
6
4X
S
b
3
bbb
ddd
C
C
C
4
A1
NOTES: UNLESS OTHERWISE SPECIFIED
1.
DIMENSIONS AND TOLERANCES
PER ANSI Y14.5M.
2.
ALL DIMENSIONS ARE IN MILLIMETERS.
3
A2
A
.25 M C A B
.10 M C
DIMENSION "b" IS MEASURED AT THE
MAXIMUM SOLDER BALL DIAMETER,
PARALLEL TO PRIMARY DATUM C
SYMBOL
MIN.
NOM.
A
1.30
1.70
2.10
A1
0.30
0.50
0.70
A2
1.40 REF
D/E
17.0 BSC
M/N
15.0 BSC
S
0.50 BSC
b
4
PRIMARY DATUM C AND SEATING
PLANE ARE DEFINED BY THE SPHERICAL
CROWNS OF THE SOLDER BALLS.
5
BILATERAL TOLERANCE ZONE IS APPLIED
TO EACH SIDE OF THE PACKAGE BODY.
6
EXACT SHAPE AND SIZE OF THIS FEATURE
IS OPTIONAL.
0.50
0.70
1.0 BSC
e
65
0.60
MAX.
aaa
-
-
0.20
bbb
-
-
0.25
ddd
-
-
0.20
Package Diagrams
256-Ball ftBGA Package Option 3: MachXO2
Dimensions in Millimeters
5
(4X)
A1 BALL I.D.
IDENTIFIER
M
16
14
15
12
13
10
11
8
9
aaa
6
7
4
5
D
A
2
3
B
1
A
B
C
D
E
F
S
G
H
J
N
E
K
L
M
N
P
R
T
e
e
6
4X
S
b
3
.25 M C A B
.10 M C
bbb
ddd
C
C
C
4
A1
NOTES: UNLESS OTHERWISE SPECIFIED
1.
DIMENSIONS AND TOLERANCES
PER ANSI Y14.5M.
2.
ALL DIMENSIONS ARE IN MILLIMETERS.
3
A2
A
DIMENSION "b" IS MEASURED AT THE
MAXIMUM SOLDER BALL DIAMETER,
PARALLEL TO PRIMARY DATUM C
MIN.
A
1.40
A1
0.30
-
-
A2
1.00
-
-
PRIMARY DATUM C AND SEATING
PLANE ARE DEFINED BY THE SPHERICAL
CROWNS OF THE SOLDER BALLS.
5
BILATERAL TOLERANCE ZONE IS APPLIED
TO EACH SIDE OF THE PACKAGE BODY.
6
EXACT SHAPE AND SIZE OF THIS FEATURE
IS OPTIONAL.
1.55
17.0 BSC
M/N
15.0 BSC
S
0.50 BSC
0.40
0.50
1.70
0.60
1.0 BSC
e
66
NOM.
D/E
b
4
MAX.
SYMBOL
aaa
-
-
0.20
bbb
-
-
0.25
ddd
-
-
0.12
Package Diagrams
256-Ball fpBGA Package
Dimensions in Millimeters
5
A1 CORNER
INDEX AREA
aaa
(4X)
A
D
M
B
B
16 15 14 13 12 11 10
9
8
7
6
5
4
3
2
1
A
B
C
D
S
E
F
G
H
E
C
N
J
K
L
M
N
P
R
T
e
e
S
3
A
.25 M C A B
.10 M C
A2
A1
ccc
bbb
ddd
C
C
C
4
C
SYMBOL
NOTES: UNLESS OTHERWISE SPECIFIED
1.
DIMENSIONS AND TOLERANCES
PER ANSI Y14.5M.
2.
ALL DIMENSIONS ARE IN MILLIMETERS.
3
6
4X
b
DIMENSION "b" IS MEASURED AT THE
MAXIMUM SOLDER BALL DIAMETER,
PARALLEL TO PRIMARY DATUM C
4
PRIMARY DATUM C AND SEATING
PLANE ARE DEFINED BY THE SPHERICAL
CROWNS OF THE SOLDER BALLS.
5
BILATERAL TOLERANCE ZONE IS APPLIED
TO EACH SIDE OF THE PACKAGE BODY.
6
EXACT SHAPE AND SIZE OF THIS FEATURE
IS OPTIONAL.
MIN.
MAX.
A
1.30
1.70
2.10
A1
0.30
0.50
0.70
A2
0.30
0.50
0.70
B/C
14.80
15.30
15.80
D/E
17.00 BSC
M/N
15.00 BSC
S
b
0.50 BSC
0.50
e
67
NOM.
0.60
0.70
1.00 BSC
aaa
-
-
0.20
bbb
-
-
0.25
ccc
-
-
0.35
ddd
-
-
0.20
Package Diagrams
256-Ball SBGA Package
Dimensions in Millimeters
(4X)
aaa
A1 BALL I.D.
IDENTIFIER
M
5
A
D
B
20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1
A
B
C
D
E
F
G
H
J
K
L
M
N
P
R
T
U
V
W
Y
S
A
A
N
E
e
e
S
b
4X
6
.30 M C A B
.15 M C
3
A1
A4
bbb
C
ddd
Q
A2 A
4
C
C
A-A SECTION VIEW
SYMBOL
NOTES: UNLESS OTHERWISE SPECIFIED
1.
DIMENSIONS AND TOLERANCES
PER ANSI Y14.5M.
2.
ALL DIMENSIONS ARE IN MILLIMETERS.
3
DIMENSION "b" IS MEASURED AT THE
MAXIMUM SOLDER BALL DIAMETER,
PARALLEL TO PRIMARY DATUM C
4
PRIMARY DATUM C AND SEATING
PLANE ARE DEFINED BY THE SPHERICAL
CROWNS OF THE SOLDER BALLS.
5
BILATERAL TOLERANCE ZONE IS APPLIED
TO EACH SIDE OF THE PACKAGE BODY.
6
EXACT SHAPE AND SIZE OF THIS FEATURE
IS OPTIONAL.
MIN.
NOM.
A
-
-
1.70
A1
0.50
0.65
0.80
A2
0.80
0.90
1.00
D/E
27.00 BSC
M/N
24.13 BSC
S
0.635 BSC
b
0.60
e
68
0.75
MAX.
0.90
1.27 BSC
Q
0.25
-
-
A4
0.10
-
-
aaa
-
-
0.20
bbb
-
-
0.25
ddd
-
-
0.20
Package Diagrams
272-Ball BGA Package
Dimensions in Millimeters
5
(4X)
aaa
A
D
M
20
18
19
14
16
17
12
13
15
A1 BALL I.D.
IDENTIFIER
8
10
11
9
4
6
7
5
3
B
B
2
1
A
B
C
D
E
F
G
S
H
J
K
N
L
C
E
M
N
P
R
T
U
V
W
Y
e
e
S
b
6
4X
3
.30 M C A B
.15 M C
A
ccc
bbb
ddd
4
1.
DIMENSIONS AND TOLERANCES
PER ANSI Y14.5M.
2.
ALL DIMENSIONS ARE IN MILLIMETERS.
C
C
SYMBOL
DIMENSION "b" IS MEASURED AT THE
MAXIMUM SOLDER BALL DIAMETER,
PARALLEL TO PRIMARY DATUM C
4
PRIMARY DATUM C AND SEATING
PLANE ARE DEFINED BY THE SPHERICAL
CROWNS OF THE SOLDER BALLS.
5
BILATERAL TOLERANCE ZONE IS APPLIED
TO EACH SIDE OF THE PACKAGE BODY.
6
EXACT SHAPE AND SIZE OF THIS FEATURE
IS OPTIONAL.
C
C
NOTES: UNLESS OTHERWISE SPECIFIED
3
A2
A1
MIN.
MAX.
A
1.90
2.25
2.80
A1
0.50
0.65
0.80
A2
0.28
0.54
0.80
B/C
23.80
24.30
24.80
D/E
27.00 BSC
M/N
24.13 BSC
S
0.635 BSC
b
0.60
0.75
0.90
1.27 BSC
e
69
NOM.
aaa
-
-
0.20
bbb
-
-
0.25
ccc
-
-
0.35
ddd
-
-
0.20
Package Diagrams
284-Ball csBGA Package
Dimensions in Millimeters
5
(4X)
aaa
A1 BALL I.D.
IDENTIFIER
M
D
A
B
14 13 12 11 10 9
8
7
6
5
4
3
2
1
A
B
C
D
E
S
F
G
N
H
E
J
K
L
M
N
P
e
e
6
4X
S
3
bbb
.15 M C A B
.05 M C
ddd
C
C
C
4
A1
NOTES: UNLESS OTHERWISE SPECIFIED
1.
DIMENSIONS AND TOLERANCES
PER ANSI Y14.5M.
2.
ALL DIMENSIONS ARE IN MILLIMETERS.
3
A2
A
b
DIMENSION "b" IS MEASURED AT THE
MAXIMUM SOLDER BALL DIAMETER,
PARALLEL TO PRIMARY DATUM C
SYMBOL
MIN.
NOM.
A
-
-
A1
0.15
-
-
A2
-
-
0.85
D/E
12.00 BSC
M/N
10.50 BSC
S
b
4
PRIMARY DATUM C AND SEATING
PLANE ARE DEFINED BY THE SPHERICAL
CROWNS OF THE SOLDER BALLS.
5
BILATERAL TOLERANCE ZONE IS APPLIED
TO EACH SIDE OF THE PACKAGE BODY.
6
EXACT SHAPE AND SIZE OF THIS FEATURE
IS OPTIONAL.
1.00
0.25 BSC
0.25
0.31
0.37
0.50 BSC
e
70
MAX.
aaa
-
-
0.10
bbb
-
-
0.10
ddd
-
-
0.08
Package Diagrams
320-Ball SBGA Package
Dimensions in Millimeters
5
(4X)
aaa
A
D
A1 BALL I.D.
IDENTIFIER
M
B
23
24
21
22
19
20
17
18
15
16
13
14
9
11
12
10
7
8
5
6
3
4
1
2
A
B
C
D
E
F
G
H
J
K
L
M
N
P
R
T
U
V
W
Y
AA
AB
AC
AD
S
A
e
A
N
E
e
S
b
4X
6
.30 M C A B
.15 M C
3
A1
A2 A
A4
bbb
ddd
Q
C
C
4
C
A-A SECTION VIEW
SYMBOL
NOTES: UNLESS OTHERWISE SPECIFIED
1.
DIMENSIONS AND TOLERANCES
PER ANSI Y14.5M.
2.
ALL DIMENSIONS ARE IN MILLIMETERS.
3
DIMENSION "b" IS MEASURED AT THE
MAXIMUM SOLDER BALL DIAMETER,
PARALLEL TO PRIMARY DATUM C
4
PRIMARY DATUM C AND SEATING
PLANE ARE DEFINED BY THE SPHERICAL
CROWNS OF THE SOLDER BALLS.
5
BILATERAL TOLERANCE ZONE IS APPLIED
TO EACH SIDE OF THE PACKAGE BODY.
6
EXACT SHAPE AND SIZE OF THIS FEATURE
IS OPTIONAL.
MIN.
MAX.
A
-
-
1.70
A1
0.50
0.65
0.80
A2
0.80
0.90
1.00
D/E
31.00 BSC
M/N
29.21 BSC
S
0.635 BSC
b
0.60
e
71
NOM.
0.75
0.90
1.27 BSC
Q
0.25
-
-
A4
0.10
-
-
aaa
-
-
0.20
bbb
-
-
0.25
ddd
-
-
0.20
Package Diagrams
324-Ball ftBGA Package
Dimensions in Millimeters
5
(4X)
A1 BALL I.D.
IDENTIFIER
M
18
16
17
14
15
12
13
10
11
aaa
8
9
6
7
4
5
D
A
2
B
1
3
A
B
C
D
E
F
S
G
H
J
K
N
E
L
M
N
P
R
T
U
V
e
e
6
4X
S
b
A2
A
3
.25 M C A B
.10 M C
bbb
ddd
C
C
C
4
A1
NOTES: UNLESS OTHERWISE SPECIFIED
1.
DIMENSIONS AND TOLERANCES
PER ANSI Y14.5M.
2.
ALL DIMENSIONS ARE IN MILLIMETERS.
3
DIMENSION "b" IS MEASURED AT THE
MAXIMUM SOLDER BALL DIAMETER,
PARALLEL TO PRIMARY DATUM C
MIN.
A
1.25
A1
0.30
-
-
A2
-
-
1.40
PRIMARY DATUM C AND SEATING
PLANE ARE DEFINED BY THE SPHERICAL
CROWNS OF THE SOLDER BALLS.
5
BILATERAL TOLERANCE ZONE IS APPLIED
TO EACH SIDE OF THE PACKAGE BODY.
6
EXACT SHAPE AND SIZE OF THIS FEATURE
IS OPTIONAL.
1.50
19.0 BSC
M/N
17.0 BSC
S
0.50 BSC
0.50
0.60
1.70
0.70
1.0 BSC
e
72
NOM.
D/E
b
4
MAX.
SYMBOL
aaa
-
-
0.20
bbb
-
-
0.25
ddd
-
-
0.20
Package Diagrams
328-Ball csBGA Package
Dimensions in Millimeters
A1 BALL
aaa
5
(4X)
IDENTIFIER
M
19 18 17 16 15 14 13 12 11 10 9
A
D
B
8 7 6 5 4 3 2 1
A
B
C
D
E
F
G
H
J
K
L
M
N
P
R
T
U
V
W
E
N
e
e
4X
6
A2
A
b
bbb
3
C
.15 M C A B
.05 M C
ddd
4
C
C
A1
NOTES: UNLESS OTHERWISE SPECIFIED
1.
DIMENSIONS AND TOLERANCES
PER ANSI Y14.5M.
2.
ALL DIMENSIONS ARE IN MILLIMETERS.
3
DIMENSION "b" IS MEASURED AT THE
MAXIMUM SOLDER BALL DIAMETER,
PARALLEL TO PRIMARY DATUM C
4
PRIMARY DATUM C AND SEATING
PLANE ARE DEFINED BY THE SPHERICAL
CROWNS OF THE SOLDER BALLS.
5
BILATERAL TOLERANCE ZONE IS APPLIED
TO EACH SIDE OF THE PACKAGE BODY.
6
EXACT SHAPE AND SIZE OF THIS FEATURE
IS OPTIONAL.
SYMBOL
MIN.
NOM.
A
1.05
1.35
A1
0.15
-
A2
-
-
D/E
10.0 BSC
M/N
9.00 BSC
b
0.25
1.50
1.20
0.35
0.50 BSC
e
73
0.30
MAX.
aaa
-
-
0.10
bbb
-
-
0.10
ddd
-
-
0.08
Package Diagrams
332-Ball caBGA Package
Dimensions in Millimeters
5
A1 CORNER
INDEX AREA
(4X)
aaa
D
M
20
18
19
16
17
14
15
12
13
10
11
8
9
6
7
4
5
A
2
3
B
1
A
B
C
D
E
F
G
H
S
J
K
L
N
E
M
N
P
R
T
U
V
W
Y
e
e
4X
S
6
b
A2
A
3
.15 M C A B
.08 M C
bbb
ddd
C
C
4
C
A1
NOTES: UNLESS OTHERWISE SPECIFIED
A
MIN.
-
NOM.
-
A1
0.25
-
-
A2
0.65
-
-
SYMBOL
1.
DIMENSIONS AND TOLERANCES
PER ANSI Y14.5M.
2.
ALL DIMENSIONS ARE IN MILLIMETERS.
3
DIMENSION "b" IS MEASURED AT THE
MAXIMUM SOLDER BALL DIAMETER,
PARALLEL TO PRIMARY DATUM C
4
PRIMARY DATUM C AND SEATING
PLANE ARE DEFINED BY THE SPHERICAL
CROWNS OF THE SOLDER BALLS.
5
BILATERAL TOLERANCE ZONE IS APPLIED
TO EACH SIDE OF THE PACKAGE BODY.
6
EXACT SHAPE AND SIZE OF THIS FEATURE
IS OPTIONAL.
D/E
17.0 BSC
M/N
15.2 BSC
S
0.40 BSC
b
0.40
0.50
0.80 BSC
e
74
0.45
MAX.
2.00
aaa
-
-
0.15
bbb
-
-
0.20
ddd
-
-
0.20
Package Diagrams
352-Ball SBGA Package
Dimensions in Millimeters
5
(4X)
aaa
A
D
A1 BALL I.D.
IDENTIFIER
M
B
26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1
A
B
C
D
E
F
G
H
S
J
K
L
M
N
P
R
T
U
V
W
Y
AA
AB
AC
AD
AE
AF
A
e
A
N
E
e
S
6
4X
b
.30 M C A B
.15 M C
3
A1
A2 A
A4
bbb
ddd
Q
C
C
4
C
A-A SECTION VIEW
SYMBOL
NOTES: UNLESS OTHERWISE SPECIFIED
1.
DIMENSIONS AND TOLERANCES
PER ANSI Y14.5M.
2.
ALL DIMENSIONS ARE IN MILLIMETERS.
3
DIMENSION "b" IS MEASURED AT THE
MAXIMUM SOLDER BALL DIAMETER,
PARALLEL TO PRIMARY DATUM C
4
PRIMARY DATUM C AND SEATING
PLANE ARE DEFINED BY THE SPHERICAL
CROWNS OF THE SOLDER BALLS.
5
BILATERAL TOLERANCE ZONE IS APPLIED
TO EACH SIDE OF THE PACKAGE BODY.
6
EXACT SHAPE AND SIZE OF THIS FEATURE
IS OPTIONAL.
NOM.
A
-
-
1.70
A1
0.50
0.65
0.80
A2
0.80
0.90
1.00
D/E
35.00 BSC
M/N
31.75 BSC
S
0.635 BSC
b
0.60
e
75
MAX.
MIN.
0.75
0.90
1.27 BSC
Q
0.25
-
-
A4
0.10
-
-
aaa
-
-
0.20
bbb
-
-
0.25
ddd
-
-
0.20
Package Diagrams
388-Ball BGA Package
Dimensions in Millimeters
5
(4X)
aaa
A
D
A1 BALL I.D.
IDENTIFIER
M
26
24
25
22
23
18
20
21
19
16
17
14
15
12
13
10
11
6
8
9
7
4
5
B
B
2
3
1
A
B
C
D
E
F
G
H
J
S
K
L
M
N
N
P
C
E
R
T
U
V
W
Y
AA
AB
AC
AD
AE
AF
e
e
S
3
A2
A
.30 M C A B
.15 M C
A1
ccc
bbb
ddd
C
C
C
4
C
SYMBOL
NOTES: UNLESS OTHERWISE SPECIFIED
1.
DIMENSIONS AND TOLERANCES
PER ANSI Y14.5M.
2.
ALL DIMENSIONS ARE IN MILLIMETERS.
3
6
4X
b
DIMENSION "b" IS MEASURED AT THE
MAXIMUM SOLDER BALL DIAMETER,
PARALLEL TO PRIMARY DATUM C
4
PRIMARY DATUM C AND SEATING
PLANE ARE DEFINED BY THE SPHERICAL
CROWNS OF THE SOLDER BALLS.
5
BILATERAL TOLERANCE ZONE IS APPLIED
TO EACH SIDE OF THE PACKAGE BODY.
6
EXACT SHAPE AND SIZE OF THIS FEATURE
IS OPTIONAL.
MIN.
MAX.
1.90
2.80
3.25
A1
0.50
0.65
0.80
A2
0.28
0.54
0.80
B/C
29.80
31.80
33.80
D/E
35.00 BSC
M/N
31.75 BSC
S
0.635 BSC
b
0.60
e
76
NOM.
A
0.75
0.90
1.27 BSC
aaa
-
-
0.20
bbb
-
-
0.25
ccc
-
-
0.35
ddd
-
-
0.20
Package Diagrams
388-Ball fpBGA Package
Dimensions in Millimeters
A1 CORNER
INDEX AREA
5
(4X)
aaa
A
D
M
B
B
22 21 20 19 18 17 16 15 14 13 12 11 10
9
8
7
6
5
4
3
2
1
A
B
C
D
E
F
G
S
H
J
K
L
N
M
C
E
N
P
R
T
U
V
W
Y
AA
AB
e
e
S
6
4X
b
A
3
.25 M C A B
.10 M C
ccc
bbb
ddd
C
C
C
4
C
SYMBOL
NOTES: UNLESS OTHERWISE SPECIFIED
1.
DIMENSIONS AND TOLERANCES
PER ANSI Y14.5M.
2.
ALL DIMENSIONS ARE IN MILLIMETERS.
3
A2
A1
DIMENSION "b" IS MEASURED AT THE
MAXIMUM SOLDER BALL DIAMETER,
PARALLEL TO PRIMARY DATUM C
4
PRIMARY DATUM C AND SEATING
PLANE ARE DEFINED BY THE SPHERICAL
CROWNS OF THE SOLDER BALLS.
5
BILATERAL TOLERANCE ZONE IS APPLIED
TO EACH SIDE OF THE PACKAGE BODY.
6
EXACT SHAPE AND SIZE OF THIS FEATURE
IS OPTIONAL.
MIN.
MAX.
A
1.70
2.15
2.60
A1
0.30
0.50
0.70
A2
0.30
0.50
0.70
B/C
19.30
19.80
20.30
D/E
23.00 BSC
M/N
21.00 BSC
0.50 BSC
S
b
0.50
e
77
NOM.
0.60
0.70
1.00 BSC
aaa
-
-
0.20
bbb
-
-
0.25
ccc
-
-
0.35
ddd
-
-
0.20
Package Diagrams
416-Ball fpBGA Package
Dimensions in Millimeters
A1 CORNER
INDEX AREA
5
aaa
(4X)
24
25
20
22
23
21
18
19
16
17
14
15
A
D
M
26
13
8
10
12
9
11
4
6
7
5
B
2
3
B
1
A
B
C
D
E
F
G
H
J
S
K
L
M
N
P
N
C
E
R
T
U
V
W
Y
AA
AB
AC
AD
AE
AF
e
e
S
6
4X
b
3
A
.25 M C A B
.10 M C
A1
ccc
C
bbb
ddd
C
4
C
SYMBOL
NOTES: UNLESS OTHERWISE SPECIFIED
1.
DIMENSIONS AND TOLERANCES
PER ANSI Y14.5M.
2.
ALL DIMENSIONS ARE IN MILLIMETERS.
3
C
DIMENSION "b" IS MEASURED AT THE
MAXIMUM SOLDER BALL DIAMETER,
PARALLEL TO PRIMARY DATUM C
4
PRIMARY DATUM C AND SEATING
PLANE ARE DEFINED BY THE SPHERICAL
CROWNS OF THE SOLDER BALLS.
5
BILATERAL TOLERANCE ZONE IS APPLIED
TO EACH SIDE OF THE PACKAGE BODY.
6
EXACT SHAPE AND SIZE OF THIS FEATURE
IS OPTIONAL.
MIN.
MAX.
1.70
2.15
2.60
A1
0.30
0.50
0.70
A2
0.30
0.50
0.70
B/C
23.80
24.80
25.80
D/E
27.00 BSC
M/N
25.00 BSC
0.50 BSC
S
b
0.50
0.60
0.70
1.00 BSC
e
78
NOM.
A
aaa
-
-
0.20
bbb
-
-
0.25
ccc
-
-
0.35
ddd
-
-
0.20
A2
Package Diagrams
432-Ball SBGA Package
Dimensions in Millimeters
5
(4X)
aaa
A1 BALL I.D.
IDENTIFIER
A
D
M
B
31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1
A
A
B
C
D
E
F
G
H
J
K
L
M
N
P
R
T
U
V
W
Y
AA
AB
AC
AD
AE
AF
AG
AH
AJ
AK
AL
S
A
N
E
e
e
S
6
4X
b
.30 M C A B
.15 M C
3
A1
bbb
A4
ddd
A2 A
C
C
4
C
Q
A-A SECTION VIEW
SYMBOL
NOTES: UNLESS OTHERWISE SPECIFIED
1.
DIMENSIONS AND TOLERANCES
PER ANSI Y14.5M.
2.
ALL DIMENSIONS ARE IN MILLIMETERS.
3
DIMENSION "b" IS MEASURED AT THE
MAXIMUM SOLDER BALL DIAMETER,
PARALLEL TO PRIMARY DATUM C
4
PRIMARY DATUM C AND SEATING
PLANE ARE DEFINED BY THE SPHERICAL
CROWNS OF THE SOLDER BALLS.
5
BILATERAL TOLERANCE ZONE IS APPLIED
TO EACH SIDE OF THE PACKAGE BODY.
6
EXACT SHAPE AND SIZE OF THIS FEATURE
IS OPTIONAL.
MIN.
MAX.
A
-
-
1.70
A1
0.50
0.65
0.80
A2
0.80
0.90
1.00
D/E
40.00 BSC
M/N
38.10 BSC
S
b
0.00 BSC
0.60
e
79
NOM.
0.75
0.90
1.27 BSC
Q
0.25
-
-
A4
0.10
-
-
aaa
-
-
0.20
bbb
-
-
0.25
ddd
-
-
0.20
Package Diagrams
484-Ball fpBGA Package
Dimensions in Millimeters
A1 CORNER
INDEX AREA
(4X)
5
aaa
A
D
M
B
B
22 21 20 19 18 17 16 15 14 13 12 11 10
9
8
7
6
5
4
3
2
1
A
B
C
D
E
F
G
S
H
J
K
L
N
M
C
E
N
P
R
T
U
V
W
Y
AA
AB
e
e
S
6
4X
b
A
3
.25 M C A B
.10 M C
ccc
bbb
ddd
C
C
C
4
C
SYMBOL
NOTES: UNLESS OTHERWISE SPECIFIED
1.
DIMENSIONS AND TOLERANCES
PER ANSI Y14.5M.
2.
ALL DIMENSIONS ARE IN MILLIMETERS.
3
A2
A1
DIMENSION "b" IS MEASURED AT THE
MAXIMUM SOLDER BALL DIAMETER,
PARALLEL TO PRIMARY DATUM C
4
PRIMARY DATUM C AND SEATING
PLANE ARE DEFINED BY THE SPHERICAL
CROWNS OF THE SOLDER BALLS.
5
BILATERAL TOLERANCE ZONE IS APPLIED
TO EACH SIDE OF THE PACKAGE BODY.
6
EXACT SHAPE AND SIZE OF THIS FEATURE
IS OPTIONAL.
MIN.
MAX.
A
1.70
2.15
2.60
A1
0.30
0.50
0.70
A2
0.30
0.50
0.70
B/C
19.30
19.80
20.30
D/E
23.00 BSC
M/N
21.00 BSC
0.50 BSC
S
b
0.50
e
80
NOM.
0.60
0.70
1.00 BSC
aaa
-
-
0.20
bbb
-
-
0.25
ccc
-
-
0.35
ddd
-
-
0.20
Package Diagrams
516-Ball fpBGA Package
Dimensions in Millimeters
A1 CORNER
INDEX AREA
5
aaa
(4X)
A
D
M
30
28
29
26
27
24
25
20
22
23
21
18
19
16
17
14
15
10
12
13
11
8
9
6
7
4
5
2
3
B
B
1
A
B
C
D
E
F
G
H
J
K
L
S
M
N
P
R
OPTIONAL FEATURE
(HEAT SINK)
N
T
E
C
U
6
V
W
Y
AA
AB
AC
AD
AE
AF
AG
AH
AJ
e
AK
b
e
S
4X
.25 M C A B
.10 M C
3
6
A
A1
ccc
C
bbb
ddd
C
4
C
SYMBOL
NOTES: UNLESS OTHERWISE SPECIFIED
1.
DIMENSIONS AND TOLERANCES
PER ANSI Y14.5M.
2.
ALL DIMENSIONS ARE IN MILLIMETERS.
3
C
DIMENSION "b" IS MEASURED AT THE
MAXIMUM SOLDER BALL DIAMETER,
PARALLEL TO PRIMARY DATUM C
4
PRIMARY DATUM C AND SEATING
PLANE ARE DEFINED BY THE SPHERICAL
CROWNS OF THE SOLDER BALLS.
5
BILATERAL TOLERANCE ZONE IS APPLIED
TO EACH SIDE OF THE PACKAGE BODY.
6
EXACT SHAPE AND SIZE OF THIS FEATURE
IS OPTIONAL.
MIN.
MAX.
A
1.70
2.15
2.60
A1
0.30
0.50
0.70
A2
0.30
0.50
0.70
B/C
25.80
27.55
29.30
D/E
31.00 BSC
M/N
29.00 BSC
0.50 BSC
S
b
0.50
0.60
0.70
1.00 BSC
e
81
NOM.
aaa
-
-
0.20
bbb
-
-
0.25
ccc
-
-
0.35
ddd
-
-
0.20
A2
Package Diagrams
672-Ball fpBGA Package
Dimensions in Millimeters
A1 CORNER
INDEX AREA
5
aaa
(4X)
24
25
20
22
23
21
18
19
16
17
14
15
A
D
M
26
13
8
10
12
9
11
6
7
4
5
B
2
3
B
1
A
B
C
D
E
F
G
H
J
S
K
L
M
N
P
N
C
E
R
T
U
V
W
Y
AA
AB
AC
AD
AE
AF
e
e
S
6
4X
b
3
A
.25 M C A B
.10 M C
A1
ccc
C
bbb
ddd
C
4
C
SYMBOL
NOTES: UNLESS OTHERWISE SPECIFIED
1.
DIMENSIONS AND TOLERANCES
PER ANSI Y14.5M.
2.
ALL DIMENSIONS ARE IN MILLIMETERS.
3
C
DIMENSION "b" IS MEASURED AT THE
MAXIMUM SOLDER BALL DIAMETER,
PARALLEL TO PRIMARY DATUM C
4
PRIMARY DATUM C AND SEATING
PLANE ARE DEFINED BY THE SPHERICAL
CROWNS OF THE SOLDER BALLS.
5
BILATERAL TOLERANCE ZONE IS APPLIED
TO EACH SIDE OF THE PACKAGE BODY.
6
EXACT SHAPE AND SIZE OF THIS FEATURE
IS OPTIONAL.
MIN.
MAX.
1.70
2.15
2.60
A1
0.30
0.50
0.70
A2
0.30
0.50
0.70
B/C
23.80
24.80
25.80
D/E
27.00 BSC
M/N
25.00 BSC
S
b
0.50 BSC
0.50
0.60
0.70
1.00 BSC
e
82
NOM.
A
aaa
-
-
0.20
bbb
-
-
0.25
ccc
-
-
0.35
ddd
-
-
0.20
A2
Package Diagrams
676-Ball fpBGA Package
Dimensions in Millimeters
A1 CORNER
INDEX AREA
5
aaa
(4X)
A
D
M
26
28
30
29
27
24
25
20
22
23
21
18
19
16
17
14
15
10
12
13
11
8
9
6
7
4
5
2
3
B
B
1
A
B
C
D
E
F
G
H
J
K
L
S
M
N
P
R
N
T
E
C
U
V
W
Y
AA
AB
AC
AD
AE
AF
AG
AH
AJ
e
AK
b
e
S
4X
.25 M C A B
.10 M C
3
6
A
A1
ccc
C
bbb
ddd
C
4
C
SYMBOL
NOTES: UNLESS OTHERWISE SPECIFIED
1.
DIMENSIONS AND TOLERANCES
PER ANSI Y14.5M.
2.
ALL DIMENSIONS ARE IN MILLIMETERS.
3
C
DIMENSION "b" IS MEASURED AT THE
MAXIMUM SOLDER BALL DIAMETER,
PARALLEL TO PRIMARY DATUM C
4
PRIMARY DATUM C AND SEATING
PLANE ARE DEFINED BY THE SPHERICAL
CROWNS OF THE SOLDER BALLS.
5
BILATERAL TOLERANCE ZONE IS APPLIED
TO EACH SIDE OF THE PACKAGE BODY.
6
EXACT SHAPE AND SIZE OF THIS FEATURE
IS OPTIONAL.
MIN.
MAX.
A
1.70
2.15
2.60
A1
0.30
0.50
0.70
A2
0.30
0.50
0.70
B/C
25.80
27.55
29.30
D/E
31.00 BSC
M/N
29.00 BSC
S
b
0.50 BSC
0.50
0.60
0.70
1.00 BSC
e
83
NOM.
aaa
-
-
0.20
bbb
-
-
0.25
ccc
-
-
0.35
ddd
-
-
0.20
A2
Package Diagrams
676-Ball fcBGA Package
Dimensions in Millimeters
5
A1 CORNER
INDEX AREA
aaa
(4X)
A
D
M
B
26
24
25
20
22
23
21
16
18
19
17
14
15
13
8
10
12
11
6
7
9
4
5
2
3
B
F
1
A
B
C
D
E
F
G
H
J
S
K
L
M
N
P
N
G
C
R
T
U
V
W
Y
AA
AB
AC
AD
AE
AF
e
e
S
4X
6
b
A
ccc
.25 M C A B
.10 M C
3
bbb
4
ddd
C
C
C
NOTES: UNLESS OTHERWISE SPECIFIED
1.
DIMENSIONS AND TOLERANCES
PER ANSI Y14.5M.
2.
ALL DIMENSIONS ARE IN MILLIMETERS.
MIN.
A
2.55
2.90
3.25
A1
0.40
0.50
0.60
1.20 REF
A2
26.55
D/E
4
DIMENSION "b" IS MEASURED AT THE
MAXIMUM SOLDER BALL DIAMETER,
PARALLEL TO PRIMARY DATUM C
F/G
18.55
6
BILATERAL TOLERANCE ZONE IS APPLIED
TO EACH SIDE OF THE PACKAGE BODY.
EXACT SHAPE AND SIZE OF THIS FEATURE
IS OPTIONAL.
84
18.60
18.65
0.50 BSC
0.50
e
5
26.65
25.00 BSC
S
b
26.60
27.00 BSC
M/N
PRIMARY DATUM C AND SEATING
PLANE ARE DEFINED BY THE SPHERICAL
CROWNS OF THE SOLDER BALLS.
NOM.
MAX.
SYMBOL
B/C
3
A2
A1
C
0.60
0.70
1.00 BSC
aaa
-
-
0.20
bbb
-
-
0.25
ccc
-
-
0.35
ddd
-
-
0.20
E
Package Diagrams
680-Ball fpBGA Package
(with or without Internal Heat Spreader)
Dimensions in Millimeters
5
(4X)
aaa
A1 CORNER
INDEX AREA
A
D
M
34
32
33
30
31
28
29
26
27
24
25
22
23
20
21
18
19
16
17
14
15
12
13
10
11
8
9
6
7
4
5
B
B
2
3
1
A
B
C
D
E
F
G
H
J
K
L
M
S
N
P
R
T
U
OPTIONAL FEATURE
(HEAT SINK)
N
V
C
E
W
6
Y
AA
AB
AC
AD
AE
AF
AG
AH
AJ
AK
AL
AM
AN
AP
e
e
S
6
4X
b
A2
A
3
A1
.30 M C A B
.15 M C
ccc
bbb
ddd
C
C
4
C
SYMBOL
NOTES: UNLESS OTHERWISE SPECIFIED
1.
DIMENSIONS AND TOLERANCES
PER ANSI Y14.5M.
2.
ALL DIMENSIONS ARE IN MILLIMETERS.
3
C
DIMENSION "b" IS MEASURED AT THE
MAXIMUM SOLDER BALL DIAMETER,
PARALLEL TO PRIMARY DATUM C
4
PRIMARY DATUM C AND SEATING
PLANE ARE DEFINED BY THE SPHERICAL
CROWNS OF THE SOLDER BALLS.
5
BILATERAL TOLERANCE ZONE IS APPLIED
TO EACH SIDE OF THE PACKAGE BODY.
6
EXACT SHAPE AND SIZE OF THIS FEATURE
IS OPTIONAL.
MIN.
MAX.
A
1.90
2.25
2.60
A1
0.30
0.50
0.70
A2
0.40
0.60
0.80
B/C
29.80
30.30
30.80
D/E
35.00 BSC
M/N
33.00 BSC
S
b
0.50 BSC
0.50
e
85
NOM.
0.60
0.70
1.00 BSC
aaa
-
-
0.20
bbb
-
-
0.25
ccc
-
-
0.35
ddd
-
-
0.20
Package Diagrams
680-Ball fpSBGA Package
Dimensions in Millimeters
A1 BALL I.D.
IDENTIFIER
aaa
5
(4X)
M
38
39
36
37
34
35
32
33
30
31
28
29
26
27
24
25
18
19
21
A
D
20
22
23
16
14
15
17
10
12
13
11
8
9
6
7
4
5
B
2
3
1
A
B
C
D
E
F
G
H
J
K
L
M
N
P
R
T
S
U
V
W
Y
N
E
AA
AB
AC
A
AD
AE
e
AF
AG
AH
AJ
AK
AL
AM
AN
AP
AR
AT
AU
AV
AW
S
e
b
3
4X
.25 M C A B
.10 M C
6
A
A
A2
bbb
A4
C
C
Q
A1
4
A-A SECTION VIEW
SYMBOL
NOTES: UNLESS OTHERWISE SPECIFIED
1.
2.
3
DIMENSIONS AND TOLERANCES
PER ANSI Y14.5M.
NOM.
-
-
1.70
MAX.
A1
0.45
0.53
0.60
A2
0.90
0.98
1.05
ALL DIMENSIONS ARE IN MILLIMETERS.
DIMENSION "b" IS MEASURED AT THE
MAXIMUM SOLDER BALL DIAMETER,
PARALLEL TO PRIMARY DATUM C
4
PRIMARY DATUM C AND SEATING
PLANE ARE DEFINED BY THE SPHERICAL
CROWNS OF THE SOLDER BALLS.
5
BILATERAL TOLERANCE ZONE IS APPLIED
TO EACH SIDE OF THE PACKAGE BODY.
6
MIN.
A
D/E
40.00 BSC
M/N
38.00 BSC
S
b
0.00 BSC
0.50
e
EXACT SHAPE AND SIZE OF THIS FEATURE
IS OPTIONAL.
86
0.65
0.80
1.00 BSC
Q
0.25
-
A4
0.10
-
aaa
-
-
0.20
bbb
-
-
0.25
ddd
-
-
0.20
-
SEATING PLANE
ddd
Package Diagrams
900-Ball fpBGA Package
Dimensions in Millimeters
5
A1 CORNER
INDEX AREA
aaa
(4X)
A
D
M
30
28
29
26
27
24
25
20
22
23
21
18
19
16
17
14
15
10
12
13
11
8
9
6
7
4
5
2
3
B
B
1
A
B
C
D
E
F
G
H
J
K
L
S
M
N
P
R
N
T
E
C
U
V
W
Y
AA
AB
AC
AD
AE
AF
AG
AH
AJ
e
AK
b
e
S
4X
.25 M C A B
.10 M C
3
6
A
A1
ccc
C
bbb
ddd
C
4
C
SYMBOL
NOTES: UNLESS OTHERWISE SPECIFIED
1.
DIMENSIONS AND TOLERANCES
PER ANSI Y14.5M.
2.
ALL DIMENSIONS ARE IN MILLIMETERS.
3
C
DIMENSION "b" IS MEASURED AT THE
MAXIMUM SOLDER BALL DIAMETER,
PARALLEL TO PRIMARY DATUM C
4
PRIMARY DATUM C AND SEATING
PLANE ARE DEFINED BY THE SPHERICAL
CROWNS OF THE SOLDER BALLS.
5
BILATERAL TOLERANCE ZONE IS APPLIED
TO EACH SIDE OF THE PACKAGE BODY.
6
EXACT SHAPE AND SIZE OF THIS FEATURE
IS OPTIONAL.
MIN.
MAX.
A
1.70
2.15
2.60
A1
0.30
0.50
0.70
A2
0.30
0.50
0.70
B/C
25.80
27.55
29.30
D/E
31.00 BSC
M/N
29.00 BSC
S
b
0.50 BSC
0.50
e
87
NOM.
0.60
0.70
1.00 BSC
aaa
-
-
0.20
bbb
-
-
0.25
ccc
-
-
0.35
ddd
-
-
0.20
A2
Package Diagrams
1020-Ball Organic fcBGA Package
Dimensions in Millimeters
5
A1 CORNER
INDEX AREA
aaa
(4X)
A
D
M
B
32
30
31
28
29
26
27
24
25
20
22
23
21
18
19
16
17
14
15
10
12
13
11
8
9
6
7
4
5
B
2
3
1
A
B
C
D
E
F
G
H
J
K
L
M
S
N
P
R
T
U
N
E
C
V
W
Y
AA
AB
AC
AD
AE
AF
AG
AH
AJ
AK
e
AL
AM
4X
e
S
b
6
.25 M C A B
.10 M C
3
A
A2
ccc
bbb
ddd
A1
C
C
C
4
C
SYMBOL
NOTES: UNLESS OTHERWISE SPECIFIED
1.
DIMENSIONS AND TOLERANCES
PER ANSI Y14.5M.
2.
ALL DIMENSIONS ARE IN MILLIMETERS.
MIN.
A
2.52
3.12
3.82
0.30
0.50
0.70
B/C
3
4
1.24 REF
31.10
33.00 BSC
M/N
31.00 BSC
b
BILATERAL TOLERANCE ZONE IS APPLIED
TO EACH SIDE OF THE PACKAGE BODY.
6
EXACT SHAPE AND SIZE OF THIS FEATURE
IS OPTIONAL.
88
32.90
0.50 BSC
0.50
e
5
32.00
D/E
S
PRIMARY DATUM C AND SEATING
PLANE ARE DEFINED BY THE SPHERICAL
CROWNS OF THE SOLDER BALLS.
MAX.
A1
A2
DIMENSION "b" IS MEASURED AT THE
MAXIMUM SOLDER BALL DIAMETER,
PARALLEL TO PRIMARY DATUM C
NOM.
0.60
0.70
1.00 BSC
aaa
-
-
0.20
bbb
-
-
0.25
ccc
-
-
0.35
ddd
-
-
0.20
Package Diagrams
1020-Ball Organic fcBGA Package Rev. 2
Dimensions in Millimeters
5
A1 CORNER
INDEX AREA
aaa
(4X)
A
D
M
32
30
31
28
29
26
27
24
25
20
22
23
21
18
19
B
16
17
14
15
10
12
13
11
8
9
6
7
4
5
2
3
B
F
1
A
B
C
D
E
F
G
H
J
K
L
M
S
N
P
R
T
U
N
G
C
V
W
Y
AA
AB
AC
AD
AE
AF
AG
AH
AJ
AK
e
AL
AM
e
S
b
4X
6
.25 M C A B
.10 M C
3
A
ccc
1020X
bbb
4
ddd
C
C
C
NOTES: UNLESS OTHERWISE SPECIFIED
1.
DIMENSIONS AND TOLERANCES
PER ANSI Y14.5M.
SYMBOL
MIN.
A
2.55
2.90
3.25
A1
0.40
0.50
0.60
32.40
DIMENSION "b" IS MEASURED AT THE
MAXIMUM SOLDER BALL DIAMETER,
PARALLEL TO PRIMARY DATUM C
4
PRIMARY DATUM C AND SEATING
PLANE ARE DEFINED BY THE SPHERICAL
CROWNS OF THE SOLDER BALLS.
5
BILATERAL TOLERANCE ZONE IS APPLIED
TO EACH SIDE OF THE PACKAGE BODY.
32.60
32.80
F/G
33.00 BSC
24.50
S
b
EXACT SHAPE AND SIZE OF THIS FEATURE
IS OPTIONAL.
89
24.60
24.70
31.00 BSC
M/N
0.50 BSC
0.50
e
6
MAX.
ALL DIMENSIONS ARE IN MILLIMETERS.
D/E
3
NOM.
1.20 REF
A2
B/C
2.
A2
A1
C
0.60
0.70
1.00 BSC
aaa
-
-
0.20
bbb
-
-
0.25
ccc
-
-
0.35
ddd
-
-
0.20
E
Package Diagrams
1036-Ball ftSBGA Package
Dimensions in Millimeters
A1 BALL I.D.
IDENTIFIER
5
aaa
(4X)
M
A
D
B
44
42
43
40
41
38
39
36
37
34
35
32
33
30
31
28
29
26
27
24
25
22
23
20
21
18
19
16
17
14
15
12
13
10
11
8
9
6
7
4
5
2
3
1
A
C
E
G
J
L
N
R
S
U
W
AA
AC
AE
AG
AJ
A
AL
AN
AR
e
AU
AW
BA
BC
B
D
F
H
K
M
P
T
V
Y
AB
N
AD
E
AF
AH
AK
AM
AP
AT
AV
AY
BB
BD
S
e
3
6
4X
b
A
.30 M C A B
.10 M C
A1
bbb
A4
ddd
C
C
4
C
Q
A-A SECTION VIEW
SYMBOL
NOTES: UNLESS OTHERWISE SPECIFIED
1.
2.
DIMENSIONS AND TOLERANCES
PER ANSI Y14.5M.
ALL DIMENSIONS ARE IN MILLIMETERS.
3
DIMENSION "b" IS MEASURED AT THE
MAXIMUM SOLDER BALL DIAMETER,
PARALLEL TO PRIMARY DATUM C
4
PRIMARY DATUM C AND SEATING
PLANE ARE DEFINED BY THE SPHERICAL
CROWNS OF THE SOLDER BALLS.
5
BILATERAL TOLERANCE ZONE IS APPLIED
TO EACH SIDE OF THE PACKAGE BODY.
6
EXACT SHAPE AND SIZE OF THIS FEATURE
IS OPTIONAL.
MIN.
MAX.
-
-
1.80
A1
0.40
0.55
0.70
A2
0.90
0.98
1.10
D/E
45.00 BSC
M/N
43.00 BSC
0.50 BSC
S
b
0.50
0.65
0.80
1.00 BSC
e
90
NOM.
A
Q
0.25
-
A4
-
0.10
-
-
aaa
-
-
0.20
bbb
-
-
0.35
ddd
-
-
0.20
A2 A
Package Diagrams
1152-Ball Organic fcBGA Package Option 1: LatticeSC/SCM40
Dimensions in Millimeters
5
A1 CORNER
INDEX AREA
aaa
(4X)
A
D
B
M
34
32
33
30
31
28
29
26
27
24
25
20
22
23
21
16
18
19
17
14
15
10
12
13
11
8
9
4
6
5
7
2
3
B
26.6 REF
1
A
B
C
D
E
F
G
H
J
K
L
M
N
S
26.6 REF
P
R
T
U
V
N
W
Y
C
AA
AB
AC
AD
AE
AF
AG
AH
AJ
AK
AL
AM
e
AN
AP
e
S
(1152X)
b
4X
6
.25 M C A B
.10 M C
3
A
ccc
bbb
4
ddd
C
C
C
NOTES: UNLESS OTHERWISE SPECIFIED
1.
DIMENSIONS AND TOLERANCES
PER ANSI Y14.5M.
2.
ALL DIMENSIONS ARE IN MILLIMETERS.
SYMBOL
MIN.
A
2.55
2.90
3.25
A1
0.35
0.50
0.65
B/C
3
4
PRIMARY DATUM C AND SEATING
PLANE ARE DEFINED BY THE SPHERICAL
CROWNS OF THE SOLDER BALLS.
5
BILATERAL TOLERANCE ZONE IS APPLIED
TO EACH SIDE OF THE PACKAGE BODY.
6
EXACT SHAPE AND SIZE OF THIS FEATURE
IS OPTIONAL.
34.25
34.50
D/E
35.00 BSC
M/N
33.00 BSC
S
b
MAX.
34.75
0.50 BSC
0.50
e
91
NOM.
1.20 REF
A2
DIMENSION "b" IS MEASURED AT THE
MAXIMUM SOLDER BALL DIAMETER,
PARALLEL TO PRIMARY DATUM C
A2
A1
C
0.60
0.70
1.00 BSC
aaa
-
-
0.20
bbb
-
-
0.25
ccc
-
-
0.35
ddd
-
-
0.20
E
Package Diagrams
1152-Ball Organic fcBGA Package Option 2: LatticeSC/SCM80 & SC/SCM115
Dimensions in Millimeters
5
aaa
(4X)
A
D
6
M
34
32
33
30
31
28
29
26
27
24
25
20
22
23
21
B
16
18
19
17
14
15
10
12
13
11
8
4
6
7
9
B
2
5
3
1
A
B
C
A1 CORNER
INDEX AREA
D
E
F
G
6
H
J
K
L
M
N
S
P
R
T
U
V
C
N
E
W
Y
AA
AB
AC
AD
AE
AF
AG
AH
AJ
AK
AL
AM
e
AN
AP
e
S
(1152X)
b
4X
6
.25 M C A B
.10 M C
3
A
ccc
bbb
ddd
C
C
4
C
NOTES: UNLESS OTHERWISE SPECIFIED
1.
DIMENSIONS AND TOLERANCES
PER ANSI Y14.5M.
MIN.
A
2.80
3.15
3.50
A1
0.35
0.50
0.65
4
NOM.
1.20 REF
ALL DIMENSIONS ARE IN MILLIMETERS.
B/C
3
MAX.
SYMBOL
A2
2.
DIMENSION "b" IS MEASURED AT THE
MAXIMUM SOLDER BALL DIAMETER,
PARALLEL TO PRIMARY DATUM C
34.30
D/E
35.00 BSC
33.00 BSC
b
BILATERAL TOLERANCE ZONE IS APPLIED
TO EACH SIDE OF THE PACKAGE BODY.
6
EXACT SHAPE AND SIZE OF THIS FEATURE
IS OPTIONAL.
92
34.90
0.50 BSC
0.50
e
5
34.60
M/N
S
PRIMARY DATUM C AND SEATING
PLANE ARE DEFINED BY THE SPHERICAL
CROWNS OF THE SOLDER BALLS.
A2
A1
C
0.60
0.70
1.00 BSC
aaa
-
-
0.20
bbb
-
-
0.25
ccc
-
-
0.35
ddd
-
-
0.23
Package Diagrams
1152-Ball Ceramic fcBGA Package
Dimensions in Millimeters
5
A1 CORNER
INDEX AREA
aaa
(4X)
A
D
M
B
34
32
33
30
31
28
29
26
27
24
25
20
22
23
21
18
19
16
17
14
15
10
12
13
11
8
9
6
4
5
7
B
2
3
1
A
B
C
D
E
F
G
H
J
K
L
M
N
S
P
R
T
U
V
N
E
C
W
Y
AA
AB
AC
AD
AE
AF
AG
AH
AJ
AK
AL
e
AM
AN
AP
e
S
b
4X
6
.25 M C A B
.10 M C
3
A
A2
ccc
bbb
ddd
A1
C
C
C
4
C
SYMBOL
NOTES: UNLESS OTHERWISE SPECIFIED
1.
DIMENSIONS AND TOLERANCES
PER ANSI Y14.5M.
2.
ALL DIMENSIONS ARE IN MILLIMETERS.
MIN.
A
4.00
4.60
5.20
0.30
0.50
0.70
1.40 REF
A2
3
4
PRIMARY DATUM C AND SEATING
PLANE ARE DEFINED BY THE SPHERICAL
CROWNS OF THE SOLDER BALLS.
5
BILATERAL TOLERANCE ZONE IS APPLIED
TO EACH SIDE OF THE PACKAGE BODY.
6
EXACT SHAPE AND SIZE OF THIS FEATURE
IS OPTIONAL.
33.10
34.00
D/E
35.00 BSC
M/N
33.00 BSC
b
34.90
0.50 BSC
S
0.50
0.60
0.70
1.00 BSC
e
93
MAX.
A1
B/C
DIMENSION "b" IS MEASURED AT THE
MAXIMUM SOLDER BALL DIAMETER,
PARALLEL TO PRIMARY DATUM C
NOM.
aaa
-
-
0.20
bbb
-
-
0.25
ccc
-
-
0.35
ddd
-
-
0.20
Package Diagrams
1152-Ball fpBGA Package
Dimensions in Millimeters
5
(4X)
aaa
A1 CORNER
INDEX AREA
A
D
M
34
32
33
30
31
28
29
26
27
24
25
22
23
20
21
18
19
16
17
14
15
12
13
10
11
8
9
6
7
3
B
B
2
4
5
1
A
C
E
G
J
L
S
N
R
U
W
B
D
F
H
K
M
P
T
N
V
C
E
Y
AA
AB
AC
AD
AE
AF
AG
AH
AJ
AK
AL
AM
AN
AP
e
e
S
6
4X
b
A
3
A1
.25 M C A B
.10 M C
bbb
ddd
C
C
C
4
C
NOTES: UNLESS OTHERWISE SPECIFIED
1.
DIMENSIONS AND TOLERANCES
PER ANSI Y14.5M.
2.
ALL DIMENSIONS ARE IN MILLIMETERS.
DIMENSION "b" IS MEASURED AT THE
MAXIMUM SOLDER BALL DIAMETER,
PARALLEL TO PRIMARY DATUM C
3
ccc
4
PRIMARY DATUM C AND SEATING
PLANE ARE DEFINED BY THE SPHERICAL
CROWNS OF THE SOLDER BALLS.
5
BILATERAL TOLERANCE ZONE IS APPLIED
TO EACH SIDE OF THE PACKAGE BODY.
6
EXACT SHAPE AND SIZE OF THIS FEATURE
IS OPTIONAL.
MIN.
A
1.90
2.25
2.60
A1
0.30
0.50
0.70
A2
0.40
0.60
0.80
B/C
29.80
30.30
30.80
D/E
35.00 BSC
M/N
33.00 BSC
0.50 BSC
S
b
Depopulated ball locations are
M12, M23, AC12, and AC23.
94
NOM.
MAX.
SYMBOL
0.50
e
Note:
A2
0.60
0.70
1.00 BSC
aaa
-
-
0.20
bbb
-
-
0.25
ccc
-
-
0.35
ddd
-
-
0.20
Package Diagrams
1156-Ball fpBGA Package
Dimensions in Millimeters
5
(4X)
aaa
A1 CORNER
INDEX AREA
A
D
M
34
32
33
30
31
28
29
26
27
24
25
22
23
20
21
18
19
16
17
14
15
12
13
10
11
8
9
6
7
4
5
B
B
2
3
1
A
B
C
D
E
F
G
H
J
K
L
M
S
N
P
R
T
U
N
V
C
E
W
Y
AA
AB
AC
AD
AE
AF
AG
AH
AJ
AK
AL
AM
AN
AP
e
e
S
6
4X
b
A2
A
3
A1
.25 M C A B
.10 M C
ccc
bbb
ddd
C
C
4
C
SYMBOL
NOTES: UNLESS OTHERWISE SPECIFIED
1.
DIMENSIONS AND TOLERANCES
PER ANSI Y14.5M.
2.
ALL DIMENSIONS ARE IN MILLIMETERS.
3
C
DIMENSION "b" IS MEASURED AT THE
MAXIMUM SOLDER BALL DIAMETER,
PARALLEL TO PRIMARY DATUM C
4
PRIMARY DATUM C AND SEATING
PLANE ARE DEFINED BY THE SPHERICAL
CROWNS OF THE SOLDER BALLS.
5
BILATERAL TOLERANCE ZONE IS APPLIED
TO EACH SIDE OF THE PACKAGE BODY.
6
EXACT SHAPE AND SIZE OF THIS FEATURE
IS OPTIONAL.
MIN.
MAX.
A
1.90
2.25
2.60
A1
0.30
0.50
0.70
A2
0.40
0.60
0.80
B/C
29.80
30.30
30.80
D/E
35.00 BSC
M/N
33.00 BSC
0.50 BSC
S
b
0.50
e
95
NOM.
0.60
0.70
1.00 BSC
aaa
-
-
0.20
bbb
-
-
0.25
ccc
-
-
0.35
ddd
-
-
0.20
Package Diagrams
1704-Ball Organic fcBGA Package
Dimensions in Millimeters
5
aaa
A1 CORNER
INDEX AREA
(4X)
A
D
B
M
40
42
41
38
39
36
37
34
35
32
33
30
31
28
29
26
27
24
25
20
22
23
21
18
19
16
14
15
17
10
12
13
11
8
7
9
4
6
5
B
2
3
1
A
B
C
D
E
F
G
H
J
K
L
M
N
P
R
T
U
S
V
W
Y
AA
AB
E
C
N
AC
AD
AE
AF
AG
AH
AJ
AK
AL
AM
AN
AP
AR
AT
AU
AV
AW
AY
e
BA
BB
(1704X)
b
e
S
4X
6
.25 M C A B
.10 M C
3
A
ccc
bbb
4
ddd
C
C
C
NOTES: UNLESS OTHERWISE SPECIFIED
1.
DIMENSIONS AND TOLERANCES
PER ANSI Y14.5M.
2.
ALL DIMENSIONS ARE IN MILLIMETERS.
SYMBOL
MIN.
A
2.55
2.90
3.25
A1
0.35
0.50
0.65
B/C
3
4
PRIMARY DATUM C AND SEATING
PLANE ARE DEFINED BY THE SPHERICAL
CROWNS OF THE SOLDER BALLS.
5
BILATERAL TOLERANCE ZONE IS APPLIED
TO EACH SIDE OF THE PACKAGE BODY.
41.70
D/E
42.50 BSC
42.50 BSC
b
96
MAX.
42.30
0.50 BSC
0.50
e
6
42.00
M/N
S
EXACT SHAPE AND SIZE OF THIS FEATURE
IS OPTIONAL.
NOM.
1.20 REF
A2
DIMENSION "b" IS MEASURED AT THE
MAXIMUM SOLDER BALL DIAMETER,
PARALLEL TO PRIMARY DATUM C
A2
A1
C
0.60
0.70
1.00 BSC
aaa
-
-
0.20
bbb
-
-
0.25
ccc
-
-
0.35
ddd
-
-
0.23
Package Diagrams
1704-Ball Ceramic fcBGA Package
Dimensions in Millimeters
5
A1 BALL I.D.
IDENTIFIER
aaa
(4X)
A
D
M
40
42
38
39
41
36
37
34
35
32
33
30
31
28
29
26
27
24
25
20
22
23
21
18
19
16
14
15
17
10
12
13
11
8
9
4
6
7
5
B
2
3
1
A
B
C
D
E
F
G
H
J
K
L
M
N
P
R
T
U
S
V
W
Y
AA
AB
E
N
AC
AD
AE
AF
AG
AH
AJ
AK
AL
AM
AN
AP
AR
e
AT
AU
AV
AW
AY
BA
BB
b
3
S
e
.25 M C A B
.10 M C
4X
ccc
bbb
ddd
A
6
A2
A1
C
C
C
4
C
NOTES: UNLESS OTHERWISE SPECIFIED
SYMBOL
MIN.
A
4.30
NOM.
MAX.
4.80
5.30
1.
DIMENSIONS AND TOLERANCES
PER ANSI Y14.5M.
A1
0.30
0.50
0.70
2.
ALL DIMENSIONS ARE IN MILLIMETERS.
A2
1.30
1.60
1.90
DIMENSION "b" IS MEASURED AT THE
MAXIMUM SOLDER BALL DIAMETER,
PARALLEL TO PRIMARY DATUM C
3
D/E
42.50 BSC
M/N
41.00 BSC
S
PRIMARY DATUM C AND SEATING
PLANE ARE DEFINED BY THE SPHERICAL
CROWNS OF THE SOLDER BALLS.
4
b
e
BILATERAL TOLERANCE ZONE IS APPLIED
TO EACH SIDE OF THE PACKAGE BODY.
PACKAGE BODY INCLUDES SUBSTRATE AND LID.
5
MAXIMUM OFFSET: 0.20 mm
6
0.50 BSC
0.50
EXACT SHAPE AND SIZE OF THIS FEATURE
IS OPTIONAL.
97
0.60
0.70
1.00 BSC
aaa
-
-
0.20
bbb
-
-
0.25
ccc
-
-
0.35
ddd
-
-
0.20
Package Diagrams
Revision History
Date
Version
–
–
Change Summary
Previous Lattice releases.
October 2006
01.0
Added 64-pin TQFP and 1704-ball fcBGA package diagrams.
January 2007
01.1
Added Marking Orientation text for all TQFP packages (1.0 mm and 1.4 mm thick).
February 2007
01.2
Revised 1704 fcBGA package drawing: removed lid dimension, clarified package body
dimension as the combination of substrate and lid.
June 2007
01.3
Added 1036 ftSBGA package diagram.
October 2007
01.4
Revised 1036 ftSBGA package diagram. Removed 1036 fpSBGA.
November 2007
01.5
Added 1152-ball fpBGA package diagram.
April 2008
01.6
Added 64-ball csBGA and 144-ball csBGA package diagrams.
November 2008
01.7
Added 64-ball ucBGA and 132-ball ucBGA package diagrams.
December 2008
01.8
Added 32-pin QFNS, 48-pin QFNS and 64-pin QFNS package diagrams.
April 2009
01.9
Added 24-pin QFNS package diagram. Removed discontinued and obsolete packages
(16 SOIC, 20 SOIC, 24 SOIC, 28 SOIC, 16 PDIP, 240 MQFP, 269 fcBGA, 304 MQFP, 600
SBGA).
May 2009
02.0
Added new 256-ball caBGA and 256-ball ftBGA (Option A) packages.
December 2009
02.1
Revised 256-ball caBGA package to specify correct JEDEC reference number.
February 2010
02.2
Revised 256-ball caBGA nominal solder ball diameter from 0.5 mm to 0.45 mm to better
match actual dimension.
March 2010
02.3
Added new 1020-ball Organic fcBGA rev.2, 1152-ball Organic fcBGA, and 1704-ball
Organic fcBGA package drawings. Removed obsolete 492-Ball BGA package.
September 2010
02.4
Revised maximum coplanarity values on Organic 1152 Flip Chip BGA – Option 2 and on
Organic 1704 Flip Chip BGA from 0.20 mm to 0.23 mm.
October 2010
02.5
Added 208-ball ftBGA package.
November 2010
02.6
Added 25-ball WLCS and 332-ball caBGA package drawings. Revised 100-pin PQFP,
120-pin PQFP, 128-pin PQFP, 160-pin PQFP and 208-pin PQFP package drawings.
Removed obsolete packages including 144-, 240- and 304-pin PQFP packages.
May 2011
02.7
Added MachXO2 to the list of applicable products for the 256 ftBGA Option 1 package
outline.
July 2011
02.8
Included revised diagrams for the following packages: 56-ball csBGA, 100-ball csBGA
and 132-ball csBGA. Added new 256-ball ftBGA Option 3 package.
October 2011
02.9
Added 328-ball csBGA package.
October 2011
03.0
Added 49-ball WLCS package and updated 25-ball WLCS package.
December 2011
03.1
Updated WLCS package offering.
February 2012
03.2
Updated document with new corporate logo.
March 2012
03.3
Added new 32-Pin QFNS Package Option 2 for MachXO2. Moved 32-pin QFN (punch
singulated) package drawing to new Package Archive Appendix.
July 2012
03.4
Added 676-ball fcBGA package.
August 2012
03.5
Added 36-ball ucBGA, 49-ball ucBGA, 81-ball ucBGA, 81-ball csBGA, 84-pin QFN, 100pin TQFP Option 2, 121-ball csBGA, 121-ball ucBGA, 132-ball csBGA Option 2, 196-ball
csBGA, 225-ball ucBGA, 284-ball csBGA packages.
September 2012
03.6
Nomenclature change – “iCE40 100-Pin TQFP Package Option 2” changed to “iCE40
100-Pin VQFP Package Option 2”.
October 2012
03.7
Revised 324-ball ftBGA package drawing.
November 2012
03.8
Added iCE40 to the list of applicable products for the 32-pin QFNS Option 1 package.
February 2013
03.9
Added 184-ball csBGA package.
98
Package Diagrams
Appendix A. Package Archive
32-Pin QFN (Punch Singulated) Package
Dimensions in Millimeters
2X
0.25 C
A
4
5.00
A
b
4.75
0.10
M
C A B
D2
PIN #1 ID FIDUCIAL
LOCATED IN THIS AREA
2X
0.25 C
N
N
B
1
3
1
PIN 1 ID
4.75
E2
5.00
L
0.20 C
32X
B
2X
e
B
3
TOP VIEW
0.20 C
A
3.5
2X
4X
0
BOTTOM VIEW
A2
A
5
C
0.08 C
SIDE VIEW
A3
A1
SEATING
PLANE
SYMBOL
NOTES: UNLESS OTHERWISE SPECIFIED
1.
DIMENSIONS AND TOLERANCES
PER ANSI Y14.5M.
2.
ALL DIMENSIONS ARE IN MILLIMETERS.
MIN.
3
4
5
MAX.
-
0.85
1.00
A1
0.00
0.01
0.05
A2
0.00
0.65
1.00
A3
EXACT SHAPE AND SIZE OF THIS
FEATURE IS OPTIONAL.
NOM.
A
0.20 REF
D2
1.25
E2
1.25
2.70
3.25
2.70
3.25
DIMENSION b APPLIES TO PLATED
TERMINAL AND IS MEASURED BETWEEN
0.20 AND 0.25 mm FROM TERMINAL TIP.
b
0.18
0.24
0.30
APPLIES TO EXPOSED PORTION OF TERMINALS.
L
0.30
0.40
0.50
0
-
e
99
0.50 BSC
-
12