MTTB Series – 5 X 3.2 Ceramic SMD VCTCXO Low Profile SMD Device Hermetically Sealed Tight Stability Over Temperature Low Power Consumption Frequency Range Frequency Stability vs Temperature* Frequency vs Time Operating Temperature Range Storage Temperature Range Supply Voltage (±10%) 10.000MHZ to 32.000MHZ (See Frequency Stability vs Temperature Table) ±1 ppm per year (See Frequency Stability vs Temperature Table) -40°C to +85°C +2.6 VDC to +2.8VDC +3.0 VDC to +3.3VDC +2.6 VDC to +2.8VDC +3.0 VDC to +3.3VDC Vc = +1.40VDC Vc = +1.50VDC Vc = +1.40VDC Vc = +1.50VDC Control Voltage +0.40VDC to +0.50VDC to +0.40VDC to +0.50VDC to +2.40VDC +2.80VDC +2.40VDC +2.80VDC Supply Current 1.5mA max 5mA max Output Type Clipped Sinewave HCMOS Logic “1” = 90% of Vdd Min Output Level 0.9 – 1.4 Vp-p Logic “0” = 10% of Vdd Max Load 10k Ohms // 10pF 15pF Harmonics -10dBc max Frequency Tunning Range ±3 ppm to ±25 ppm Phase Noise -135dBc/Hz max (at 1kHz offset) Start-up Time 2ms max (Output level will be 90% from the final value) * Inclusive of Temperature., Load, and Voltage Environmental & Mechanical Detail Shock Solderability Solvent Resistance Vibration Gross Leak Test Fine Leak Test MSL MIL-STD-883, Method 2002, Condition B MIL-STD-883, Method 2003 MIL-STD-883, Method 215 MIL-STD-883, Method 2007, Condition A MIL-STD-883, Method 1014, Condition C MIL-STD-883, Method 1014, Condition A-2 Level 1 per IPC/JEDEC J-STD 20 Phase Noise Marking Detail Line 1 = MXXXXX M = XXXXX = Line 2 = SYYWWL S = = YYWW MMD Frequency in MHZ Internal Code 4 Digit Date Code (Year / Week) Denotes RoHS Compliant L = Line 3 = XXXXX Internal use only May vary with lots Black dot to denote Pin 1 MMD Monitor/Quartztek 30400 Esperanza, Rancho Santa Margarita, CA, 92688 Phone: (949) 709-5075, Fax: (949) 709-3536, www.mmdcomp.com [email protected] Revision: Revisions only with customer approval MTTB121120J Pg 1 of 2 Part Number Guide Frequency Stability vs Temperature Table Code A G C D E F Stability Temp 0°C TO +50°C 0°C TO +70°C -20°C TO +70°C -30°C TO +70°C -30°C TO +80°C -40°C TO +85°C 10 ±1.0ppm ● ● ● ● ● ● Tape & Reel Dimensions 15 20 ±1.5ppm ±2.0ppm ● ● ● ● ● ● ● ● ● ● ● ● ● = Available 25 ±2.5ppm ● ● ● ● ● ● 30 ±3.0ppm ● ● ● ● ● ● 50 ±5.0ppm ● ● ● ● ● ● Mechanical Details PITCH TAPE WIDTH REEL DIA Q1 Q2 Q1 Q2 Q3 Q4 Q3 Q4 PITCH TAPE WIDTH REEL DIA QTY PER REEL PIN 1 ORIENT. 8.00 [.315] 12.00 [.472] 330[13 IN] 1000 Q1 DIRECTION OF FEED NOTES: UNLESS OTHERWISE SPECIFIED 1. Applicable Standards / Specifications ANSI Y14.5M, Dimensions and Tolerances EIA-481-B, 8 mm through 200mm Embossed Carrier Taping and 8 mm and 12 mm Punched Carrier Taping of Surface Mount Components for Automatic Handling. 2. Dimensions are in millimeters. 3. Tolerances are ±0.10 [.004] mm unless otherwise specified. 4. Do not scale drawing. MMD Monitor/Quartztek 30400 Esperanza, Rancho Santa Margarita, CA, 92688 Phone: (949) 709-5075, Fax: (949) 709-3536, www.mmdcomp.com [email protected] Revision: Revisions only with customer approval MTTB121120J Pg 2 of 2