T Series Crystal 3.2mm X 2.5mm SMD Wide Frequency Range RoHS Compliant Tight Tolerance and Stability Frequency Range 12.000MHz to 54.000MHz Frequency Tolerance / Stability (See Part Number Guide for Options) Operating Temperature Range (See Part Number Guide for Options) Storage Temperature -40°C to +85°C Aging ±5ppm / first year max Shunt Capacitance 5pF Max Load Capacitance (See Part Number Guide for Options) Equivalent Series Resistance (ESR) See ESR Chart Drive Level 10µW Typ / 100µW Max Insulation Resistance 500 Megaohms Min at 100VDC ±15VDC ESR Chart Frequency Range ESR (Ohms) Mode / Cut 12.000MHz to 19.999MHz 100 Max Fund / AT 20.000MHz to 29.999MHz 80 Max Fund / AT 30.000MHz to 54.000MHz 50 Max Fund / AT Marking Detail Environmental & Mechanical Detail Shock MIL-STD-883, Method 2002 Cond B Solderability MIL-STD-883, Method 2003 Solvent Resistance MIL-STD-202, Method 215 Vibration MIL-STD-883, Method 2007, Cond A Gross Leak Test MIL-STD-883, Method 1014, Cond C Fine Leak Test MIL-STD-883, Method 1014, Cond A2 MSL Level 1 per IPC/JEDEC J-STD 20 First Line = MXX.X (not to exceed 5 characters) M XX.X = MMD Device Frequency = (four digits including decimal point) Second Line = SYWW (not to exceed 5 characters) S YYWW = Internal Code = Date Code (Year/Week) MMD Monitor/Quartztek 30400 Esperanza, Rancho Santa Margarita, CA, 92688 Phone: (949) 709-5075, Fax: (949) 709-3536, www.mmdcomp.com [email protected] Revision: Specifications are subject to change without notice. 04/19/11 H Pg 1 of 2 Part Number Guide T Frequency 1 3.2mm x 2.5mm 4 pads Load Capacitance XX = XXpF (8pF to 50pF) Temperature Tolerance/Stability B = ±30 ppm / ±50 ppm F = ±30 ppm / ±30 ppm G = ±10 ppm / ±30 ppm N = ±10 ppm / ±10 ppm P = ±20 ppm / ±20 ppm Operating Temperature A = 0°C to +70°c B = -20°C to +70°c C = -40°C to +85°c D = -10°C to +60°c E = -10°C to +70°c Packaging Mode of Operation Blank = Bulk T = Tape and Reel 1 = Fundamental Please Consult with MMD Sales Department for any other Parameters or Options Mechanical Details PIN 1 2 3 4 3.45 [.136] MAX CONNECTION CRYSTAL NC CRYSTAL NC MXX.XXX SYMCCL 0.75 [.030] MAX 2.00 [.079] 2.75 [.108] MAX 1 2 4 3 2.12 [.083] 1.70 [.067] 1.60 [.063] 1.20 [.047] 0.91 [.036] 1.12 [.044] 1.50 [.059] SUGGESTED LAND PATTERN DIMENSIONS IN BRACKETS ARE IN INCHES Tape and Reel PITCH 16.00 REEL DIA Q1 Q2 Q1 Q2 Q3 Q4 Q3 Q4 PITCH TAPE WIDTH REEL DIA COUNT PIN 1 ORIENT. 4.00 [.157] 8.00 [.315] 180 [7.0] 1000 Q1 NOTES: UNLESS OTHERWISE SPECIFIED 1. Applicable Standards / Specifications ANSI Y14.5M, Dimensions and Tolerances EIA-481-B, 8 mm through 200mm Embossed Carrier Taping and 8 mm and 12 mm Punched Carrier Taping of Surface Mount Components for Automatic Handling. 2. Dimensions are in millimeters [inch]. 3. Tolerances are ±0.1 [.004] mm unless otherwise specified. 4. Do not scale drawing. DIRECTION OF FEED MMD Monitor/Quartztek 30400 Esperanza, Rancho Santa Margarita, CA, 92688 Phone: (949) 709-5075, Fax: (949) 709-3536, www.mmdcomp.com [email protected] Revision: Specifications are subject to change without notice. 04/19/11 H Pg 2 of 2