MMD DF1

D & F Series Crystal
 HC-49/S SMD Crystal
 3rd Lead Ground Option Available
 Wide Frequency Range
 Fundamental or 3rd OT AT Cut
Frequency Range
3.200MHz to 80.000MHz
Frequency Tolerance / Stability
(See Part Number Guide for Options)
Operating Temperature Range
(See Part Number Guide for Options)
Storage Temperature
-55°C to +125°C
Aging
±5ppm / first year Max
Shunt Capacitance
7pF Max
Load Capacitance
20pF Standard
(See Part Number Guide for Options)
Equivalent Series Resistance
See ESR Chart
Mode of Operation
See ESR Chart
Drive Level
1mW Max
Environmental & Mechanical Detail
Shock
MIL-STD-883, Method 2002 Cond B
Solderability
MIL-STD-883, Method 2003
Solvent Resistance
MIL-STD-202, Method 215
Vibration
MIL-STD-883, Method 2007, Cond A
Gross Leak Test
MIL-STD-883, Method 1014, Cond C
Fine Leak Test
MIL-STD-883, Method 1014, Cond A2
MSL
Level 1 per IPC/JEDEC J-STD 20
Marking Detail
Line 1: MXX.XXX
XX.XXX = Frequency in MHz
Line 2: SYMCCL
S = Internal Code
YM = Date Code (Year/Month)
CC = Crystal Parameters Code
L = Denotes RoHS Compliant
MMD Monitor/Quartztek
30400 Esperanza, Rancho Santa Margarita, CA, 92688
Phone: (949) 709-5075, Fax: (949) 709-3536, www.mmdcomp.com
[email protected]
Revision:
Specifications are subject to change without notice.
10/20/10 P
Pg 1 of 4
ESR Chart
Frequency Range
ESR (Ohms)
Mode / Cut
3.200MHz to 3.999MHz
150 Max
Fund / AT
4.000MHz to 4.999MHz
120 Max
Fund / AT
5.000MHz to 5.999MHz
100 Max
Fund / AT
6.000MHz to 7.999MHz
90 Max
Fund / AT
8.000MHz to 9.999MHz
70 Max
Fund / AT
10.000MHz to 11.999MHz
50 Max
Fund / AT
12.000MHz to 14.999MHz
50 Max
Fund / AT
15.000MHz to 19.999MHz
40 Max
Fund / AT
20.000MHz to 33.000MHz
30 Max
Fund / AT
24.576MHz to 29.999MHz
100 Max
3rd OT / AT
30.000MHz to 80.000MHz
80 Max
3rd OT / AT
Part Number Guide
Frequency
D = HC-49/US SMD (4.5mm*)
F = HC-49/US SMD (3.5mm*)
*Max Height
RoHS Compliant
Blank = Not Compliant
F = Is Compliant
Load Capacitance
S = Series
20 = 20pF (Standard)
XX = XXpF (8pF to 50pF)
Temperature
Tolerance/Stability**
A = ±50 ppm / ±100 ppm
B = ±30 ppm / ± 50 ppm
C = ±15 ppm / ± 30 ppm
D = ±10 ppm / ± 15 ppm
E = ±50 ppm / ± 50 ppm
N = ±10 ppm / ± 10 ppm
Mode of Operation***
1 = Fundamental
3 = 3rd Overtone
Operating Temperature
A = 0°C to +70°C
B = -20°C to +70°C
C = -40°C to +85°C
I = -40°C to +105°C
Value Added Options
Blank = No Added Options
T = Tape and Reel
3 = 3rd Lead
* Please consult with MMD sales department for any other parameters or options.
** Not all Frequency Tolerance/Stability options available at this temperature range.
***Mode is dependant upon Frequency. See ESR Chart
MMD Monitor/Quartztek
30400 Esperanza, Rancho Santa Margarita, CA, 92688
Phone: (949) 709-5075, Fax: (949) 709-3536, www.mmdcomp.com
[email protected]
Revision:
Specifications are subject to change without notice.
10/20/10 P
Pg 2 of 4
Mechanical Details
13.20 [.520]
MAX
MXXXXX
SYMCCL
D = 4.50 [.177] MAX
F = 3.50 [.138] MAX
0.79 [.031]
11.70 [.461]
MAX
4.88 [.192]
5.00 [.197]
MAX
DIMENSION IN BRACKETS ARE IN INCHES
2.00 [.079]
5.50 [.217]
PIN CONNECTIONS
PIN 1
CRYSTAL
CRYSTAL
PIN 2
15.00 [.591]
4.00 [.157]
SUGGESTED
LAND PATTERN
Tape & Reel
Pitch
Tape Width
REEL DIA
DIRECTION OF FEED
PITCH
TAPE WIDTH
REEL DIA
COUNT.
12.00 [.628]
24.00 [.945]
330 [13]
1000
NOTES: UNLESS OTHERWISE SPECIFIED
1. Applicable Standards / Specifications
ANSI Y14.5M, Dimensions and Tolerances
EIA-481-B, 8 mm through 200mm Embossed Carrier Taping and 8 mm and 12 mm
Punched Carrier Taping of Surface Mount Components for Automatic Handling.
2. Dimensions are in millimeters.
3. Tolerances are ±0.1 [.004] mm unless otherwise specified.
4. Do not scale drawing.
MMD Monitor/Quartztek
30400 Esperanza, Rancho Santa Margarita, CA, 92688
Phone: (949) 709-5075, Fax: (949) 709-3536, www.mmdcomp.com
[email protected]
Revision:
Specifications are subject to change without notice.
10/20/10 P
Pg 3 of 4
3rd Lead Mechanical Details
MXXXXX
SYMCCL
4.80 [.189]
MAX
4.20 [.165]
MAX
0.65 [.026]
1
12.70 [.500]
MAX
3
11.50 [.453]
MAX
4.40 [.173]
2
0.95 [.037]
DIMENSION IN BRACKETS ARE IN INCHES
1.50 [.059]
5.00 [.197]
4.00 [.157]
1.50 [.059]
4.00 [.157]
PIN CONNECTIONS
CRYSTAL
PIN 1
CRYSTAL
PIN 2
PIN 3
CASE GROUND
5.00 [.197]
SUGGESTED
LAND PATTERN
3rd Lead Tape & Reel Dimensions
Pitch
Tape Width
REEL DIA
PITCH
TAPE WIDTH
REEL DIA
COUNT
12.00 [.471]
24.00 [.942]
330 [13.0]
1000pcs
NOTES: UNLESS OTHERWISE SPECIFIED
Applicable Standards / Specifications
ANSI Y14.5M, Dimensions and Tolerances
EIA-481-B, 8 mm through 200mm Embossed Carrier Taping and 8 mm and 12 mm
Punched Carrier Taping of Surface Mount Components for Automatic Handling.
Dimensions are in millimeters.
Tolerances are ±0.10 [.004] mm unless otherwise specified.
Do not scale drawing.
MMD Monitor/Quartztek
30400 Esperanza, Rancho Santa Margarita, CA, 92688
Phone: (949) 709-5075, Fax: (949) 709-3536, www.mmdcomp.com
[email protected]
Revision:
Specifications are subject to change without notice.
10/20/10 P
Pg 4 of 4