T Series.pub - MMD Components

T Series Crystal
 3.2mm X 2.5mm SMD
 Wide Frequency Range
 RoHS Compliant
 Tight Tolerance and Stability
Frequency Range
12.000MHz to 54.000MHz
Frequency Tolerance / Stability
(See Part Number Guide for Options)
Operating Temperature Range
(See Part Number Guide for Options)
Storage Temperature
-40°C to +85°C
Aging
±5ppm / first year max
Shunt Capacitance
5pF Max
Load Capacitance
(See Part Number Guide for Options)
Equivalent Series Resistance (ESR)
See ESR Chart
Drive Level
10µW Typ / 100µW Max
Insulation Resistance
500 Megaohms Min at 100VDC ±15VDC
ESR Chart
Frequency Range
ESR (Ohms)
Mode / Cut
12.000MHz to 19.999MHz
100 Max
Fund / AT
20.000MHz to 29.999MHz
80 Max
Fund / AT
30.000MHz to 54.000MHz
50 Max
Fund / AT
Marking Detail
Environmental & Mechanical Detail
Shock
MIL-STD-883, Method 2002 Cond B
First Line = MXX.XXX
Solderability
MIL-STD-883, Method 2003
M
Solvent Resistance
MIL-STD-202, Method 215
XX.XXX
Vibration
MIL-STD-883, Method 2007, Cond A
Gross Leak Test
MIL-STD-883, Method 1014, Cond C
Fine Leak Test
MIL-STD-883, Method 1014, Cond A2
MSL
Level 1 per IPC/JEDEC J-STD 20
= MMD
= Device Frequency
Second Line = SYYWW
S
YYWW
= Internal Code
= Date Code (Year/Week)
MMD Monitor/Quartztek
30400 Esperanza, Rancho Santa Margarita, CA, 92688
Phone: (949) 709-5075, Fax: (949) 709-3536, www.mmdcomp.com
[email protected]
Revision:
Specifications are subject to change without notice.
06/25/13 J
Pg 1 of 2
Part Number Guide
T
1
Frequency
3.2mm x 2.5mm
4 pads
Load Capacitance
XX = XXpF (8pF to 50pF)
Temperature
Tolerance/Stability
B = ±30 ppm / ±50 ppm
F = ±30 ppm / ±30 ppm
G = ±10 ppm / ±30 ppm
N = ±10 ppm / ±10 ppm
P = ±20 ppm / ±20 ppm
Operating Temperature
A = 0°C to +70°c
B = -20°C to +70°c
C = -40°C to +85°c
D = -10°C to +60°c
E = -10°C to +70°c
Packaging
Mode of Operation
1 = Fundamental
Blank = Bulk
T = Tape and Reel
Please Consult with MMD Sales Department for any other Parameters or Options
Mechanical Details
Tape and Reel
PITCH
16.00
REEL DIA
Q1 Q2
Q1 Q2
Q3 Q4
Q3 Q4
PITCH
TAPE WIDTH
REEL DIA
COUNT
PIN 1 ORIENT.
4.00 [.157]
8.00 [.315]
180 [7.0]
1000
Q1
NOTES: UNLESS OTHERWISE SPECIFIED
1. Applicable Standards / Specifications
ANSI Y14.5M, Dimensions and Tolerances
EIA-481-B, 8 mm through 200mm Embossed Carrier Taping and 8 mm and 12 mm
Punched Carrier Taping of Surface Mount Components for Automatic Handling.
2. Dimensions are in millimeters [inch].
3. Tolerances are ±0.1 [.004] mm unless otherwise specified.
4. Do not scale drawing.
DIRECTION OF FEED
MMD Monitor/Quartztek
30400 Esperanza, Rancho Santa Margarita, CA, 92688
Phone: (949) 709-5075, Fax: (949) 709-3536, www.mmdcomp.com
[email protected]
Revision:
Specifications are subject to change without notice.
06/25/13 J
Pg 2 of 2