D100EI Series Low Cost, 1W SIP High Isolation DC/DC Converters Electrical Specifications Specifications typical @ +25°C, nominal input voltage & rated output current, unless otherwise noted. Specifications subject to change without notice. Input Key Features: Parameter Conditions • 1W Output Power • Miniature SIP Case • 3,000 VDC Isolation Input Voltage Range • UL Approved (File E245422) Input Filter Reverse Polarity Input Current • Single & Dual Outputs Output • >3.5 MHour MTBF Parameter Output Voltage Accuracy Output Voltage Balance Line Regulation Load Regulation (Note 1) Ripple & Noise (20 MHz) (Note 2) Output Power Protection Temperature Coefficient Output Short Circuit • 24 Standard Models • LOWEST COST!! Min. Typ. 5 VDC Input 4.5 5.0 12 VDC Input 10.8 12.0 24 VDC Input 21.6 24.0 Internal Capacitor Conditions Min. Typ. ±1.0 Dual Output , Balanced Loads ±0.1 For Vin Change of 1% ±1.2 See Model Selection Guide 50 120 ±0.02 Momentary (1.0 Sec.) Max. 5.5 13.2 26.4 Units 0.3 A Max. ±3.0 ±1.0 Units % % % 75 mV P - P % %/ºC ±0.03 VDC General Parameter Isolation Voltage Isolation Resistance Isolation Capacitance Switching Frequency Conditions 60 Seconds 500 VDC 100 kHz, 1V Min. 3,000 1,000 Typ. Max. Units VDC M pF kHz Max. +85 +125 Units ºC ºC 95 % 60 150 Environmental Parameter Operating Temperature Range Storage Temperature Range Cooling Humidity Physical Case Size Case Material Weight Conditions Min. Typ. -40 +25 -55 Free Air Convection RH, Non-condensing Ambient 0.77 x 0.24 x 0.40 Inches (19.6 x 6.0 x 10.2 mm) Non-Conductive Black Plastic (UL94-V0) 0.07 Oz (2.1g) Reliability Specifications MicroPower Direct 292 Page Street Suite D Stoughton, MA 02072 USA Parameter MTBF Safety Standards Safety Approvals Conditions Min. Typ. MIL HDBK 217F, 25ºC, Gnd Benign 3.5 UL 1950, EN 60950, IEC 60950 UL, cUL; File No. E245422 Max. Units MHours Max. 9.0 18.0 30.0 300 450 Units Absolute Maximum Ratings T: (781) 344-8226 F: (781) 344-8481 E: [email protected] W: www.micropowerdirect.com Parameter Conditions Input Voltage Surge (1 Sec) Lead Temperature Internal Power Dissipation 5 VDC Input 12 VDC Input 24 VDC Input 1.5 mm From Case For 10 Sec All Models Min. -0.7 -0.7 -0.7 Typ. Caution: Exceeding Absolute Maximum Ratings may damage the module. These are not continuous operating ratings. www.micropowerdirect.com VDC ºC mW www.micropowerdirect.com Model Selection Guide Model Number D101EI D102EI D103EI D104EI D105EI D106EI D107EI D108EI D111EI D112EI D113EI D114EI D115EI D116EI D117EI D118EI D121EI D122EI D123EI D124EI D125EI D126EI D127EI D128EI Input Voltage (VDC) Current (mA) Voltage Nominal Range Full-Load No-Load (VDC) 5 4.5 - 5.5 286 30 5.0 5 4.5 - 5.5 267 30 9.0 5 4.5 - 5.5 256 30 12.0 5 4.5 - 5.5 250 30 15.0 5 4.5 - 5.5 278 30 ±5.0 5 4.5 - 5.5 267 30 ±9.0 5 4.5 - 5.5 256 30 ±12.0 5 4.5 - 5.5 253 30 ±15.0 12 10.8 - 13.2 115 15 5.0 12 10.8 - 13.2 110 15 9.0 12 10.8 - 13.2 105 15 12.0 12 10.8 - 13.2 103 15 15.0 12 10.8 - 13.2 113 15 ±5.0 12 10.8 - 13.2 110 15 ±9.0 12 10.8 - 13.2 105 15 ±12.0 12 10.8 - 13.2 104 15 ±15.0 24 21.6 - 26.4 57 8 5.0 24 21.6 - 26.4 54 8 9.0 24 21.6 - 26.4 52 8 12.0 24 21.6 - 26.4 51 8 15.0 24 21.6 - 26.4 56 8 ±5.0 24 21.6 - 26.4 55 8 ±9.0 24 21.6 - 26.4 52 8 ±12.0 24 21.6 - 26.4 51 8 ±15.0 Output Current Current Load Regulation (mA, Max) (mA, Min) (%, Max) 20.0 12.0 9.0 7.0 ±10.0 ±6.0 ±5.0 ±4.0 20.0 12.0 9.0 7.0 ±10.0 ±6.0 ±5.0 ±4.0 20.0 12.0 9.0 7.0 ±10.0 ±6.0 ±5.0 ±4.0 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 200.0 111.0 83.0 67.0 ±100.0 ±56.0 ±42.0 ±33.0 200.0 111.0 83.0 67.0 ±100.0 ±56.0 ±42.0 ±33.0 200.0 111.0 83.0 67.0 ±100.0 ±56.0 ±42.0 ±33.0 Rating Efficiency Fuse Slow-Blow (%, Typ) (mA) 70 75 78 80 72 75 78 79 72 76 79 81 74 76 79 80 73 77 80 82 74 76 80 81 500 500 500 500 500 500 500 500 200 200 200 200 200 200 200 200 100 100 100 100 100 100 100 100 Derating Curve Other input/output combinations are available (i.e. 3.3 VDC). Contact the factory for details at: [email protected] Notes: 1. Output load regulation is specified for a load change of 10% to 100%. 2. These units should not be operated with a load under 10% of full load. Operation at no-load may cause damage to the unit. 3. These converters will operate without external components. However, when measuring output ripple, it is recommended that an external ceramic capacitor be placed from the +Vout pin to the -Vout pin for single output units and from each output to common for dual output units. An input capacitor will enhance Output Capacitor Input stability over temperature and Vin Vout Capacitor input line variations. RecomSingle Dual mended capacitor values are 5 VDC 4.7 µF 5 VDC 10.0 µF 4.7 µF given in the table above. For 9 VDC 4.7 µF 2.2 µF applications requiring very 12 VDC 2.2 µF low output noise levels, a 24 VDC 1.0 µF 12 VDC 2.2 µF 1.0 µF simple LC filter should be 15 VDC 1.0 µF 0.47 µF effective. 4. Dual output units may be connected to provide a 10V, 18V, 24V or 30 VDC output. To do this, connect the load across the positive (+Vout) and negative (-Vout) outputs and float the output common 5. It is recommended that a fuse be used on the input of a power supply for protection. See the Model Selection table above for the correct rating. Mechanical Dimensions Pin Connections Pin Single Dual Pin Single Dual 1 2 5 +Vin -Vin -Vout +Vin -Vin -Vout 6 7 No Pin +Vout Common +Vout Notes: • All dimensions are typical in inches (mm) • Tolerance x.xx = ±0.01 (±0.25) • Pin 1 is marked by a “dot” or indentation on the side of the unit MicroPower Direct We Power Your Success - For Less! 292 Page Street Ste D Stoughton, MA 02072 • TEL: (781) 344-8226 • FAX: (781) 344-8481 • E-Mail: [email protected]