D200E Series Low Cost, 2W SIP Single & Dual Output DC/DC Converters Electrical Specifications Specifications typical @ +25°C, nominal input voltage & rated output current, unless otherwise noted. Specifications subject to change without notice. Key Features: Input • 2W Output Power • Miniature SIP Case • UL Approved (File E245422) • Single & Dual Outputs • 1,000 VDC Isolation • >3.5 MHour MTBF • 24 Standard Models • LOWEST COST!! Parameter Conditions Input Voltage Range Input Filter Reverse Polarity Input Current Min. Typ. 5 VDC Input 4.5 5.0 12 VDC Input 10.8 12.0 24 VDC Input 21.6 24.0 Internal Capacitor Max. 5.5 13.2 26.4 Units 0.3 A Max. ±3.0 ±1.0 Units % % % 150 mV P - P % %/ºC VDC Output Parameter Output Voltage Accuracy Output Voltage Balance Line Regulation Load Regulation, See Note 1 Ripple & Noise (20 MHz) Output Power Protection Temperature Coefficient Output Short Circuit Conditions Min. Typ. ±1.0 Dual Output , Balanced Loads ±0.1 For Vin Change of 1% ±1.2 See Model Selection Guide See Note 3 100 120 ±0.02 Momentary (1.0 Sec.) ±0.03 General Parameter Isolation Voltage Isolation Resistance Isolation Capacitance Switching Frequency Conditions 60 Seconds 500 VDC 100 kHz, 1V Min. 1,000 1,000 Typ. Max. Units VDC M pF kHz Max. +85 +125 Units ºC ºC 95 % 60 75 Environmental Parameter Operating Temperature Range Storage Temperature Range Cooling Humidity Physical Case Size (5V 12V & 24V Input Models) Case Material Weight Conditions Min. Typ. -40 +25 -55 Free Air Convection RH, Non-condensing Ambient 0.77 x 0.28 x 0.40 Inches (19.6 x 7.0 x 10.2 mm) Non-Conductive Black Plastic (UL94-V0) 0.07 Oz (2.1g) Reliability Specifications MicroPower Direct 292 Page Street Suite D Stoughton, MA 02072 USA Parameter MTBF Safety Standards Safety Approvals Conditions Min. Typ. MIL HDBK 217F, 25ºC, Gnd Benign 3.5 UL 1950, EN 60950, IEC 60950 UL, cUL; File No. E245422 Max. Units MHours Max. 9.0 18.0 30.0 300 450 Units Absolute Maximum Ratings T: (781) 344-8226 F: (781) 344-8481 E: [email protected] W: www.micropowerdirect.com Parameter Conditions Input Voltage Surge (1 Sec) Lead Temperature Internal Power Dissipation 5 VDC Input 12 VDC Input 24 VDC Input 1.5 mm From Case For 10 Sec All Models Min. -0.7 -0.7 -0.7 Typ. Caution: Exceeding Absolute Maximum Ratings may damage the module. These are not continuous operating ratings. www.micropowerdirect.com VDC ºC mW www.micropowerdirect.com Model Selection Guide Model Number D201E D202E D203E D204E D205E D206E D207E D208E D211E D212E D213E D214E D215E D216E D217E D218E D221E D222E D223E D224E D225E D226E D227E D228E Input Voltage (VDC) Current (mA) Voltage Nominal Range Full-Load No-Load (VDC) 5 4.5 - 5.5 494 30 5.0 5 4.5 - 5.5 488 30 9.0 5 4.5 - 5.5 476 30 12.0 5 4.5 - 5.5 476 30 15.0 5 4.5 - 5.5 488 30 ±5.0 5 4.5 - 5.5 482 30 ±9.0 5 4.5 - 5.5 470 30 ±12.0 5 4.5 - 5.5 470 30 ±15.0 12 10.8 - 13.2 203 15 5.0 12 10.8 - 13.2 201 15 9.0 12 10.8 - 13.2 196 15 12.0 12 10.8 - 13.2 196 15 15.0 12 10.8 - 13.2 201 15 ±5.0 12 10.8 - 13.2 198 15 ±9.0 12 10.8 - 13.2 194 15 ±12.0 12 10.8 - 13.2 194 15 ±15.0 24 21.6 - 26.4 100 8 5.0 24 21.6 - 26.4 99 8 9.0 24 21.6 - 26.4 97 8 12.0 24 21.6 - 26.4 97 8 15.0 24 21.6 - 26.4 99 8 ±5.0 24 21.6 - 26.4 98 8 ±9.0 24 21.6 - 26.4 96 8 ±12.0 24 21.6 - 26.4 96 8 ±15.0 Output Current Current Load Regulation (mA, Max) (mA, Min) (%, Max) 40.0 23.0 17.0 14.0 ±20.0 ±12.0 ±9.0 ±7.0 40.0 23.0 17.0 14.0 ±20.0 ±12.0 ±9.0 ±7.0 40.0 23.0 17.0 14.0 ±20.0 ±12.0 ±9.0 ±7.0 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 400.0 222.0 167.0 133.0 ±200.0 ±111.0 ±83.0 ±67.0 400.0 222.0 167.0 133.0 ±200.0 ±111.0 ±83.0 ±67.0 400.0 222.0 167.0 133.0 ±200.0 ±111.0 ±83.0 ±67.0 Notes: 1. Output load regulation is specified for a load change of 10% to 100%. 2. These units should not be operated with a load under 10% of full load. Operation at no-load may cause damage to the unit. 3. These converters will operate without external components. However, when measuring output ripple, it is recommended that an external ceramic capacitor be placed from the +Vout pin to the -Vout pin for single output units and from each output to common for dual output units. An input capacitor will enhance stability over temperature and input line variations. Recommended capacitor values are given in the table below. For applications requiring very low output noise levels, a simple LC filter should be effective. Input Capacitor 5 VDC 4.7 µF 12 VDC 2.2 µF 24 VDC 1.0 µF Vin Vout 5 VDC 9 VDC 12 VDC 15 VDC Rating Efficiency Fuse Slow-Blow (%, Typ) (mA) 81 82 84 84 82 83 85 85 82 83 85 85 83 84 86 86 83 84 86 86 84 85 87 87 1,000 1,000 1,000 1,000 1,000 1,000 1,000 1,000 500 500 500 500 500 500 500 500 200 200 200 200 200 200 200 200 Mechanical Dimensions Output Capacitor Single Dual 10.0 µF 4.7 µF 4.7 µF 2.2 µF 2.2 µF 1.0 µF 1.0 µF 0.47 µF 4. Dual output units may be connected to provide a 10V, 18V, 24V or 30 VDC output. To do this, connect the load across the positive (+Vout) and negative (-Vout) outputs and float the output common 5. It is recommended that a fuse be used on the input of a power supply for protection. See the Model Selection table above for the correct rating. Derating Curve Notes: • All dimensions are typical in inches (mm) • Tolerance x.xx = ±0.01 (±0.25) • Pin 1 is marked by a “dot” or indentation on the side of the unit Pin Connections MicroPower Direct Pin Single Dual 1 2 4 5 6 +Vin -Vin -Vout No Pin +Vout +Vin -Vin -Vout Common +Vout We Power Your Success - For Less! 292 Page Street Ste D Stoughton, MA 02072 • TEL: (781) 344-8226 • FAX: (781) 344-8481 • E-Mail: [email protected]