G100E Series Low Cost, 1W MiniDIP Single & Dual Output DC/DC Converters Electrical Specifications Specifications typical @ +25°C, nominal input voltage & rated output current, unless otherwise noted. Specifications subject to change without notice. Key Features: • 1W Output Power • Compact “MiniDIP” Case Input Parameter Conditions Input Voltage Range • EN 60950 Approved (UL) • Single & Dual Outputs • 1,000 VDC Isolation • >3.5 MHour MTBF • 24 Standard Models • LOWEST COST!! Input Filter Reverse Polarity Input Current Min. Typ. 5 VDC Input 4.5 5.0 12 VDC Input 10.8 12.0 24 VDC Input 21.6 24.0 Internal Capacitor Max. 5.5 13.2 26.4 Units 0.3 A Max. ±3.0 ±1.0 Units % % % VDC Output Parameter Output Voltage Accuracy Output Voltage Balance Line Regulation Load Regulation, See Note 1 Ripple & Noise (20 MHz) Output Power Protection Temperature Coefficient Output Short Circuit Conditions Min. Typ. ±1.0 Dual Output , Balanced Loads ±0.1 For Vin Change of 1% ±1.2 See Model Selection Guide Single Output, See Note 3 75 Dual Output, See Note 3 50 120 ±0.02 Momentary (1.0 Sec.) 100 750 ±0.03 mV P - P % %/ºC General Parameter Isolation Voltage Isolation Resistance Isolation Capacitance Switching Frequency Conditions 60 Seconds 500 VDC 100 kHz, 1V Min. 1,000 1,000 Typ. Max. Units VDC M pF kHz Max. +85 +125 Units ºC ºC 95 % 60 100 Environmental Parameter Operating Temperature Range Storage Temperature Range Cooling Humidity Physical Case Size Case Material Weight MicroPower Direct Reliability Specifications 292 Page Street Suite D Stoughton, MA 02072 USA Parameter MTBF Safety Standards Safety Approvals T: (781) 344-8226 F: (781) 344-8481 E: [email protected] W: www.micropowerdirect.com Absolute Maximum Ratings Conditions Min. Typ. -40 +25 -55 Free Air Convection RH, Non-condensing Ambient 0.79 x 0.39 x 0.28 Inches (20.0 x 10.0 x 7.0 mm) Non-Conductive Black Plastic (UL94-V0) 0.07 Oz (2.1g) Conditions Min. Typ. MIL HDBK 217F, 25ºC, Gnd Benign 3.5 UL 1950, EN 60950 UL, cUL; File No. E245422 Parameter Conditions Input Voltage Surge (1 Sec) Lead Temperature Internal Power Dissipation 5 VDC Input 12 VDC Input 24 VDC Input 1.5 mm From Case For 10 Sec All Models Min. -0.7 -0.7 -0.7 Typ. Max. Units MHours Max. 9.0 18.0 30.0 300 450 Units Caution: Exceeding Absolute Maximum Ratings may damage the module. These are not continuous operating ratings. www.micropowerdirect.com VDC ºC mW www.micropowerdirect.com Model Selection Guide Model Number G101E G102E G103E G104E G105E G106E G107E G108E G111E G112E G113E G114E G115E G116E G117E G118E G121E G122E G123E G124E G125E G126E G127E G128E Input Voltage (VDC) Current (mA) Voltage Nominal Range Full-Load No-Load (VDC) 5 4.5 - 5.5 286 30 5.0 5 4.5 - 5.5 256 30 9.0 5 4.5 - 5.5 256 30 12.0 5 4.5 - 5.5 250 30 15.0 5 4.5 - 5.5 278 30 ±5.0 5 4.5 - 5.5 260 30 ±9.0 5 4.5 - 5.5 253 30 ±12.0 5 4.5 - 5.5 250 30 ±15.0 12 10.8 - 13.2 117 15 5.0 12 10.8 - 13.2 109 15 9.0 12 10.8 - 13.2 107 15 12.0 12 10.8 - 13.2 105 15 15.0 12 10.8 - 13.2 116 15 ±5.0 12 10.8 - 13.2 107 15 ±9.0 12 10.8 - 13.2 105 15 ±12.0 12 10.8 - 13.2 107 15 ±15.0 24 21.6 - 26.4 57 8 5.0 24 21.6 - 26.4 53 8 9.0 24 21.6 - 26.4 53 8 12.0 24 21.6 - 26.4 52 8 15.0 24 21.6 - 26.4 57 8 ±5.0 24 21.6 - 26.4 52 8 ±9.0 24 21.6 - 26.4 52 8 ±12.0 24 21.6 - 26.4 52 8 ±15.0 Output Current Current Load Regulation (mA, Max) (mA, Min) (%, Max) 20.0 12.0 9.0 7.0 ±10.0 ±6.0 ±5.0 ±4.0 20.0 12.0 9.0 7.0 ±10.0 ±6.0 ±5.0 ±4.0 20.0 12.0 9.0 7.0 ±10.0 ±6.0 ±5.0 ±4.0 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 15 200.0 111.0 83.0 67.0 ±100.0 ±56.0 ±42.0 ±33.0 200.0 111.0 83.0 67.0 ±100.0 ±56.0 ±42.0 ±33.0 200.0 111.0 83.0 67.0 ±100.0 ±56.0 ±42.0 ±33.0 Efficiency Fuse Rating Slow-Blow (%, Typ) (mA) 70 78 78 80 72 77 79 80 71 76 78 79 72 78 79 78 73 78 78 79 73 79 80 80 500 500 500 500 500 500 500 500 200 200 200 200 200 200 200 200 100 100 100 100 100 100 100 100 Derating Curve Other input/output combinations are available (i.e. 3.3 VDC). Contact the factory for details at: [email protected] Notes: 1. Output load regulation is specified for a load change of 10% to 100%. 2. These units should not be operated with a load under 10% of full load. Operation at no-load may cause damage to the unit. 3. These converters will operate without external components. However, when measuring output ripple, it is recommended that an external ceramic capacitor be placed from the +Vout pin to the -Vout pin for single output units and from each outOutput Capacitor Input Vin Vout put to common for dual Capacitor Single Dual output units. An input 4.7 µF 5 VDC 10.0 µF 4.7 µF capacitor will enhance 5 VDC stability over temperature 12 VDC 2.2 µF 9 VDC 4.7 µF 2.2 µF and input line variations. 24 VDC 1.0 µF 12 VDC 2.2 µF 1.0 µF Recommended capacitor 15 VDC 1.0 µF 0.47 µF values are given in the table above. For applications requiring very low output noise levels, a simple LC filter should be effective. 4. Dual output units may be connected to provide a 10V, 18V, 24V or 30 VDC output. To do this, connect the load across the positive (+Vout) and negative (-Vout) outputs and float the output common. 5. It is recommended that a fuse be used on the input of a power supply for protection. See the Model Selection table above for the correct rating. Mechanical Dimensions Pin Connections Pin Single Dual 1 -Vin -Vin 7 NC NC 8 -Vout Common NC = No Connection Pin Single Dual 9 11 14 +Vout -Vout +Vin +Vout No Pin +Vin Notes: • All dimensions are typical in inches (mm) • Tolerance x.xx = ±0.01 (±0.25) • Pin 1 is marked by a “dot” or indentation on the top of the unit MicroPower Direct We Power Your Success - For Less! 292 Page Street Ste D Stoughton, MA 02072 • TEL: (781) 344-8226 • FAX: (781) 344-8481 • E-Mail: [email protected]