MD100x Datasheet - Micropower Direct

MD100x-xx Series
Isolated, 1W SIP,
Single & Dual Output
DC/DC Converters
Electrical Specifications
Specifications typical @ +25°C, nominal input voltage & rated output current, unless otherwise noted. Specifications subject to change without notice.
Key Features:
Input
Parameter
• 1W Output Power
• 1 kV to 6kV Isolation
• 96 Standard Models
Input Voltage Range
• Miniature SIP Case
• Efficiency to 86%
Input Filter
• -40°C to +85°C Operation
Parameter
Output Voltage Accuracy
Line Regulation
Load Regulation
Ripple & Noise (20 MHz)
Temperature Coefficient
Output Short Circuit
• Industry Standard Pin-Out
• Low Cost
Conditions
Min.
3.3 VDC Input 2.97
5 VDC Input
4.5
12 VDC Input 10.8
15 VDC Input 13.5
24 VDC Input 21.6
48 VDC Input 43.2
Capacitor Filter
Typ.
3.3
5.0
12.0
15.0
24.0
48.0
Max.
3.63
5.5
13.2
16.5
26.4
52.8
Units
Conditions
Typ.
±3.0
±1.2
±10
75
Max.
±0.02
Units
%
%
%
mV P - P
%/°C
Max.
Units
VDC
Output
Min.
For VIN Change of 1%
See Note 1
Momentary (0.5 Sec)
General
Parameter
Conditions
1xxx-xx Models
1xxx-xxI Models
1xxx-xxI4 Models
1xxx-xxI5 Models
1xxx-xxI6 Models
500 VDC
Isolation Voltage, 3 Sec
Isolation Resistance
Isolation Capacitance
Switching Frequency
EMI Characteristics
Parameter
Radiated Emissions
Conducted Emissions
ESD
RS
EFT
Surge
CS
PFMF
Standard
See Note 3
See Note 4
See Note 4
EN 55022
EN 55022
EN 61000-4-2
EN 61000-4-3
EN 61000-4-4
EN 61000-4-5
EN 61000-4-6
EN 61000-4-8
Min.
1,000
3,000
4,000
5,200
6,000
Typ.
VDC
1,000
60
80
M
pF
kHz
Level
Class B
Class B
Criteria A; ±6 kV Contact, ±8 kV Air
Criteria A; 10V/m
Criteria A; ±2 kV
Criteria A; ±2 kV
Criteria A; 10 Vrms
Criteria A ; 1A/m
Environmental
MicroPower Direct
292 Page Street
Suite D
Stoughton, MA 02072
USA
T: (781) 344-8226
F: (781) 344-8481
E: [email protected]
W: www.micropowerdirect.com
Parameter
Operating Temperature Range
Operating Temperature Range
Storage Temperature Range
Cooling
Humidity
Physical
Case Size
Case Material
Weight
Conditions
Ambient
Case
Min.
-40
Typ.
+25
-40
Free Air Convection
RH, Non-condensing
Max.
+85
+100
+125
Units
°C
°C
°C
95
%
0.76 x 0.24 x 0.39 Inches (19.5 x 6.0 x 10.0 mm)
Non-Conductive Black Plastic (UL94-V0)
0.08 Oz (2.3g)
Reliability Specifications
Parameter
MTBF
Conditions
MIL HDBK 217F, 25°C, Gnd Benign
Min.
1.121
Typ.
Max.
Units
MHours
Conditions
3.3 VDC Input
5 VDC Input
12 VDC Input
15 VDC Input
24 VDC Input
48 VDC Input
1.5 mm From Case for 10 Sec
Min.
-0.7
-0.7
-0.7
-0.7
-0.7
-0.7
Typ.
Max.
6.0
7.0
15.0
18.0
28.0
54.0
260
Units
Absolute Maximum Ratings
Parameter
Input Voltage Surge (0.1 Sec)
Lead Temperature
Caution: Exceeding Absolute Maximum Ratings may damage the module. These are not continuous operating ratings.
www.micropowerdirect.com
VDC
°C
www.micropowerdirect.com
Model Selection Guide
Input
Model
Number
MD103S-03xx
MD103S-05xx
MD103S-07xx
MD103S-09xx
MD103S-12xx
MD103S-15xx
MD103S-18xx
MD103S-24xx
MD103D-03xx
MD103D-05xx
MD103D-07xx
MD103D-09xx
MD103D-12xx
MD103D-15xx
MD103D-18xx
MD103D-24xx
MD105S-03xx
MD105S-05xx
MD105S-07xx
MD105S-09xx
MD105S-12xx
MD105S-15xx
MD105S-18xx
MD105S-24xx
MD105D-03xx
MD105D-05xx
MD105D-07xx
MD105D-09xx
MD105D-12xx
MD105D-15xx
MD105D-18xx
MD105D-24xx
MD112S-03xx
MD112S-05xx
MD112S-07xx
MD112S-09xx
MD112S-12xx
MD112S-15xx
MD112S-18xx
MD112S-24xx
MD112D-03xx
MD112D-05xx
MD112D-07xx
MD112D-09xx
MD112D-12xx
MD112D-15xx
MD112D-18xx
MD112D-24xx
MD115S-03xx
MD115S-05xx
MD115S-07xx
MD115S-09xx
MD115S-12xx
MD115S-15xx
MD115S-18xx
MD115S-24xx
MD115D-03xx
MD115D-05xx
MD115D-07xx
MD115D-09xx
MD115D-12xx
MD115D-15xx
MD115D-18xx
MD115D-24xx
Voltage (VDC)
Nominal
3.3
3.3
3.3
3.3
3.3
3.3
3.3
3.3
3.3
3.3
3.3
3.3
3.3
3.3
3.3
3.3
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
12
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
15
Output
Current (mA)
Voltage
Range
Full-Load No-Load (VDC)
2.97 - 3.63
399
28
3.3
2.97 - 3.63
389
22
5.0
2.97 - 3.63
389
25
7.2
2.97 - 3.63
379
35
9.0
2.97 - 3.63
394
30
12.0
2.97 - 3.63
389
30
15.0
2.97 - 3.63
415
30
18.0
2.97 - 3.63
415
30
24.0
2.97 - 3.63
459
30
±3.3
2.97 - 3.63
433
30
±5.0
2.97 - 3.63
421
30
±7.2
2.97 - 3.63
404
26
±9.0
2.97 - 3.63
384
30
±12.0
2.97 - 3.63
389
25
±15.0
2.97 - 3.63
404
25
±18.0
2.97 - 3.63
404
25
±24.0
4.5 - 5.5
256
15
3.3
4.5 - 5.5
247
17
5.0
4.5 - 5.5
247
16
7.2
4.5 - 5.5
244
15
9.0
4.5 - 5.5
253
17
12.0
4.5 - 5.5
233
17
15.0
4.5 - 5.5
241
16
18.0
4.5 - 5.5
244
20
24.0
4.5 - 5.5
299
20
±3.3
4.5 - 5.5
270
20
±5.0
4.5 - 5.5
253
15
±7.2
4.5 - 5.5
247
15
±9.0
4.5 - 5.5
250
20
±12.0
4.5 - 5.5
244
20
±15.0
4.5 - 5.5
247
22
±18.0
4.5 - 5.5
247
22
±24.0
10.8 - 13.2
111
12
3.3
10.8 - 13.2
105
14
5.0
10.8 - 13.2
111
14
7.2
10.8 - 13.2
104
9
9.0
10.8 - 13.2
105
13
12.0
10.8 - 13.2
102
10
15.0
10.8 - 13.2
103
11
18.0
10.8 - 13.2
110
20
24.0
10.8 - 13.2
123
13
±3.3
10.8 - 13.2
113
10
±5.0
10.8 - 13.2
110
10
±7.2
10.8 - 13.2
107
13
±9.0
10.8 - 13.2
102
10
±12.0
10.8 - 13.2
102
10
±15.0
10.8 - 13.2
102
10
±18.0
10.8 - 13.2
111
20
±24.0
13.5 - 16.5
83
10
3.3
13.5 - 16.5
82
7
5.0
85
10
7.2
13.5 - 16.5
13.5 - 16.5
85
10
9.0
13.5 - 16.5
83
8
12.0
13.5 - 16.5
84
12
15.0
13.5 - 16.5
83
10
18.0
13.5 - 16.5
80
5
24.0
13.5 - 16.5
89
20
±3.3
13.5 - 16.5
89
20
±5.0
13.5 - 16.5
89
18
±7.2
13.5 - 16.5
87
18
±9.0
13.5 - 16.5
87
20
±12.0
13.5 - 16.5
87
20
±15.0
13.5 - 16.5
89
15
±18.0
13.5 - 16.5
89
15
±24.0
I/O Isolation
Models are available with input/output isolation
levels ranging from 1 kVDC to 6 kVDC. To order
units with higher isolation levels an “Ix” is added to
the Model number, as shown in the table at right.
292 Page Street Ste D Stoughton, MA 02072
Current
Current
(mA, Max)
(mA, Min)
303
200
139
111
83
67
56
42
±152
±100
±69
±56
±42
±33
±28
±21
303
200
139
111
83
67
56
42
±152
±100
±69
±56
±42
±33
±28
±21
303
200
139
111
83
67
56
42
±152
±100
±69
±56
±42
±33
±28
±21
303
200
139
111
83
67
56
42
±152
±100
±69
±56
±42
±33
±28
±21
Model No
MD1xxx-xx
MD1xxx-xxI
MD1xxx-xxI4
MD1xxx-xxI5
MD1xxx-xxI6
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
±0.0
±0.0
±0.0
±0.0
±0.0
±0.0
±0.0
±0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
±0.0
±0.0
±0.0
±0.0
±0.0
±0.0
±0.0
±0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
±0.0
±0.0
±0.0
±0.0
±0.0
±0.0
±0.0
±0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
±0.0
±0.0
±0.0
±0.0
±0.0
±0.0
±0.0
±0.0
Efficiency
(%, Typ)
Fuse
Reflected Capacitive
Ripple
Rating
Load
Current
Slow-Blow
(µF, Max)
(mA Pk-Pk)
76
78
78
80
77
78
73
73
66
70
72
75
77
78
75
75
78
81
81
82
79
86
83
82
67
74
79
81
80
82
81
81
75
79
75
80
79
82
81
76
68
74
76
78
82
82
82
75
80
81
78
78
80
79
80
83
75
75
75
77
77
77
75
75
20.0
20.0
20.0
20.0
20.0
20.0
20.0
20.0
20.0
20.0
20.0
20.0
20.0
20.0
20.0
20.0
20.0
20.0
20.0
20.0
20.0
20.0
20.0
20.0
20.0
20.0
20.0
20.0
20.0
20.0
20.0
20.0
20.0
20.0
20.0
20.0
20.0
20.0
20.0
20.0
20.0
20.0
20.0
20.0
20.0
20.0
20.0
20.0
20.0
20.0
20.0
20.0
20.0
20.0
20.0
20.0
20.0
20.0
20.0
20.0
20.0
20.0
20.0
20.0
(mA)
220
220
220
220
220
220
220
220
±100
±100
±100
±100
±100
±100
±100
±100
220
220
220
220
220
220
220
220
±100
±100
±100
±100
±100
±100
±100
±100
220
220
220
220
220
220
220
220
±100
±100
±100
±100
±100
±100
±100
±100
220
220
220
220
220
220
220
220
±100
±100
±100
±100
±100
±100
±100
±100
1,000
1,000
1,000
1,000
1,000
1,000
1,000
1,000
1,000
1,000
1,000
1,000
1,000
1,000
1,000
1,000
500
500
500
500
500
500
500
500
500
500
500
500
500
500
500
500
300
300
300
300
300
300
300
300
300
300
300
300
300
300
300
300
200
200
200
200
200
200
200
200
200
200
200
200
200
200
200
200
Isolation Level
1 kVDC
3 kVDC
4 kVDC
5.2 kVDC
6 kVDC
• TEL: (781) 344-8226 • FAX: (781) 344-8481 • E-Mail: [email protected]
www.micropowerdirect.com
Model Selection Guide
Input
Model
Number
MD124S-03xx
MD124S-05xx
MD124S-07xx
MD124S-09xx
MD124S-12xx
MD124S-15xx
MD124S-18xx
MD124S-24xx
MD124D-03xx
MD124D-05xx
MD124D-07xx
MD124D-09xx
MD124D-12xx
MD124D-15xx
MD124D-18xx
MD124D-24xx
MD148S-03xx
MD148S-05xx
MD148S-07xx
MD148S-09xx
MD148S-12xx
MD148S-15xx
MD148S-18xx
MD148S-24xx
MD148D-03xx
MD148D-05xx
MD148D-07xx
MD148D-09xx
MD148D-12xx
MD148D-15xx
MD148D-18xx
MD148D-24xx
Voltage (VDC)
Nominal
24
24
24
24
24
24
24
24
24
24
24
24
24
24
24
24
48
48
48
48
48
48
48
48
48
48
48
48
48
48
48
48
Output
Current (mA)
Voltage
Range
Full-Load No-Load (VDC)
21.6 - 26.4
56
8
3.3
21.6 - 26.4
54
6
5.0
21.6 - 26.4
57
6
7.2
21.6 - 26.4
55
6
9.0
21.6 - 26.4
53
6
12.0
21.6 - 26.4
52
5
15.0
21.6 - 26.4
51
5
18.0
21.6 - 26.4
52
8
24.0
21.6 - 26.4
62
7
±3.3
21.6 - 26.4
56
6
±5.0
21.6 - 26.4
53
7
±7.2
21.6 - 26.4
53
7
±9.0
21.6 - 26.4
52
6
±12.0
21.6 - 26.4
52
8
±15.0
21.6 - 26.4
51
6
±18.0
21.6 - 26.4
51
8
±24.0
43.2 - 52.8
29
5
3.3
43.2 - 52.8
29
5
5.0
43.2 - 52.8
28
5
7.2
43.2 - 52.8
27
5
9.0
43.2 - 52.8
27
5
12.0
43.2 - 52.8
27
5
15.0
43.2 - 52.8
28
5
18.0
43.2 - 52.8
27
6
24.0
43.2 - 52.8
34
6
±3.3
43.2 - 52.8
31
5
±5.0
43.2 - 52.8
29
5
±7.2
43.2 - 52.8
29
5
±9.0
43.2 - 52.8
28
6
±12.0
43.2 - 52.8
27
5
±15.0
43.2 - 52.8
28
5
±18.0
43.2 - 52.8
28
6
±24.0
Notes:
1. Load regulation is measured over a range of 20% IOUT to 100% IOUT. Load
regulation for 3.3 VDC output models is specified at ±20% typical.
2. Operation at no-load will not damage the unit, but they may not meet all specifications.
3. With the addition of input filter components, all models will meet EN 55022 class B.
A suggested circuit is shown in the connection diagram below. Contact the factory
for more information.
4. To meet the requirements of EN 61000-4-4 and EN 61000-4-5, external components are needed. The connection diagram below shows an external input filter
that would typically achieve this. Contact the factory for more information.
5. It is recommended that a fuse be used on the input of a power supply for protection.
See the Model Selection tables for the correct rating.
Current
Current
(mA, Max)
(mA, Min)
303
200
139
111
83
67
56
42
±152
±100
±69
±56
±42
±33
±28
±21
303
200
139
111
83
67
56
42
±152
±100
±69
±56
±42
±33
±28
±21
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
±0.0
±0.0
±0.0
±0.0
±0.0
±0.0
±0.0
±0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0
±0.0
±0.0
±0.0
±0.0
±0.0
±0.0
±0.0
±0.0
Efficiency
(%, Typ)
Fuse
Reflected Capacitive
Rating
Ripple
Load
Current
Slow-Blow
(µF, Max)
(mA Pk-Pk)
74
77
73
76
78
80
82
80
67
74
78
78
80
80
81
82
73
73
75
76
76
77
75
76
62
68
72
73
74
77
75
74
20.0
20.0
20.0
20.0
20.0
20.0
20.0
20.0
20.0
20.0
20.0
20.0
20.0
20.0
20.0
20.0
20.0
20.0
20.0
20.0
20.0
20.0
20.0
20.0
20.0
20.0
20.0
20.0
20.0
20.0
20.0
20.0
(mA)
220
220
220
220
220
220
220
220
±100
±100
±100
±100
±100
±100
±100
±100
220
220
220
220
220
220
220
220
±100
±100
±100
±100
±100
±100
±100
±100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
75
75
75
75
75
75
75
75
75
75
75
75
75
75
75
75
Derating Curve
Typical Connection
Recommended values for components are:
For applications that require meeting EMC standards, the diagram
above illustrates a typical connection of the MD100x-xx series.
The units do not require external components to operate as specified.
All components should be mounted as close to the unit as possible.
Component
C1
L1
MD103x-xxxx
470 µF/100V
18 µH
10 µF
C2
C3
C4
MD105x-xxxx
470 µF/100V
18 µH
10 µF
The voltage rating on capacitor C3 needs to be greater than the
isolation voltage rating of the unit.
MD112x-xxxx
470 µF/100V
18 µH
10 µF
MD115x-xxxx
470 µF/100V
18 µH
Capacitor C4 is not required to meet specifications, but may be used
if a lower level of output ripple is required.
MD124x-xxxx
470 µF/100V
18 µH
1210, 2.2 µF/100V
1206, 470 pF/2kV
10 µF
MD148x-xxxx
470 µF/100V
18 µH
1210, 2.2 µF/100V
1206, 470 pF/2kV
10 µF
MicroPower Direct
•
292 Page Street Ste D Stoughton, MA 02072
10 µF
• TEL: (781) 344-8226 • FAX: (781) 344-8481 • E-Mail: [email protected]
www.micropowerdirect.com
Mechanical Dimensions, MD100X-xx Models
Pin Connections
Pin
1
2
4
5
6
Single Output
+VIN
-VIN
-VOUT
No Pin
+VOUT
Pin
1
2
4
5
6
Dual Output
+VIN
-VIN
-VOUT
Common
+VOUT
The width of 48 VDC input units is
0.28 (7.20). All other dimensions
remain the same.
Mechanical Dimensions, MD100X-xxIx Models
Pin Connections
Pin
1
2
5
6
7
Single Output
+VIN
-VIN
-VOUT
No Pin
+VOUT
Pin
1
2
5
6
7
Dual Output
+VIN
-VIN
-VOUT
Common
+VOUT
The width of 48 VDC input units is
0.28 (7.20). All other dimensions
remain the same.
Notes:
• All dimensions are typical in inches (mm)
• General Tolerance x.xx = ±0.02 (±0.5)
• Pin 1 is marked by a “dot” or indentation on the unit
MicroPower Direct
We Power Your Success - For Less!
292 Page Street Ste D Stoughton, MA 02072
•
TEL: (781) 344-8226
•
FAX: (781) 344-8481
•
E-Mail: [email protected]