MG200xxEI Datasheet

MG200xEI Series
High Isolation, 2W
Compact MiniDIP
DC/DC Converters
Electrical Specifications
Specifications typical @ +25°C, nominal input voltage & rated output current, unless otherwise noted. Specifications subject to change without notice.
Key Features:
• 2W Output Power
• Compact MiniDIP Case
Input
Parameter
Conditions
Min.
5 VDC Input 4.50
12 VDC Input 10.80
15 VDC Input 13.50
24 VDC Input 21.60
Internal Capacitor
Input Voltage Range
• 3,000 VDC Isolation
• High Efficiency
Input Filter
• Single and Dual Outputs
Output
• >3.5 MHour MTBF
Parameter
Output Voltage Accuracy
Line Regulation
Load Regulation, See Note 1
• -40°C to +85°C Operation
• LOW COST
Ripple & Noise (20 MHz), See Note 2
1.5 kV Isolation
Models
Available
Conditions
Min.
Max.
5.50
13.20
16.50
26.40
Units
Typ.
±2.5
Max.
Units
%
%
For VIN Change of 1%
See Model Selection Guide
Output Voltage <12 VDC
60
15 VDC, 24 VDC Output
75
Temperature Coefficient
5 VDC, 12 VDC & 15 VDC Input
24 VDC Input
Output Short Circuit
Typ.
5.0
12.0
15.0
24.0
±1.2
VDC
mV P - P
±0.03
%/°C
Continuous (Autorecovery)
Momentary (1.0 Sec.)
General
Parameter
Isolation Voltage
Isolation Resistance
Isolation Capacitance
Switching Frequency
EMI Characteristics
Parameter
Conditions
60 Seconds
500 VDC
100 kHz, 0.1V
Conditions
EMC Compliance, Single Output
EMC Compliance, Dual Output
Typ.
Max.
20
100
300
Units
VDC
M
pF
kHz
Min.
Conducted
Radiated
EMI Compliance, See Note 4
Min.
3,000
1,000
Electrostatic Discharge (ESD)
Typ.
Max.
Units
CISPR22/EN 55022 Level B
CISPR22/EN 55022 Level B
EN 61000-4-2 Level B Contact ±8 kV
EN 61000-4-2 Level B Contact ±6 kV
Environmental
MicroPower Direct
292 Page Street
Suite D
Stoughton, MA 02072
USA
T: (781) 344-8226
F: (781) 344-8481
E: [email protected]
W: www.micropowerdirect.com
Parameter
Operating Temperature Range
Storage Temperature Range
Cooling
Humidity
Physical
Case Size
Case Material
Weight
Conditions
Min.
Typ.
-40
+25
-55
Free Air Convection
RH, Non-condensing
Ambient
Max.
+85
+125
Units
°C
°C
95
%
0.787 x 0.394 x 0.323 Inches (20.0 x 10.0 x 8.2 mm)
Non-Conductive Black Plastic (UL-94V0)
0.08 Oz (2.4g)
Reliability Specifications
Parameter
MTBF
Conditions
MIL HDBK 217F, 25°C, Gnd Benign
Min.
3.5
Typ.
Max.
Units
MHours
Min.
-0.7
-0.7
-0.7
-0.7
Typ.
Max.
9.0
18.0
21.0
30.0
300
Units
Absolute Maximum Ratings
Parameter
Conditions
Input Voltage Surge (1 Sec)
Lead Temperature
5 VDC Input
12 VDC Input
15 VDC Input
24 VDC Input
1.5 mm From Case For 10 Sec
Caution: Exceeding Absolute Maximum Ratings may damage the module. These are not continuous operating ratings.
www.micropowerdirect.com
VDC
°C
www.micropowerdirect.com
Model Selection Guide
Input
Model
Number
Voltage (VDC)
Output
Load
Capacitive
Efficiency Fuse Rating
Load
Regulation
Slow-Blow
(µF Max)
(%, Typ)
Output
Current (mA)
Voltage
Current
Current
Full-Load No-Load
(VDC)
(mA, Max)
(mA, Min)
(mA)
Nominal
Range
MG205S-05EI
5
4.5 - 5.5
500
25
5.0
400
40.0
12.0
220
80
1,000
MG205S-12EI
5
4.5 - 5.5
476
25
12.0
167
17.0
8.0
220
84
1,000
MG205S-15EI
5
4.5 - 5.5
476
25
15.0
133
13.0
7.0
220
84
1,000
MG205D-05EI
5
4.5 - 5.5
500
25
±5.0
±200
±20.0
12.0
100
80
1,000
MG205D-12EI
5
4.5 - 5.5
476
25
±12.0
±83
±8.0
8.0
100
84
1,000
MG205D-15EI
5
4.5 - 5.5
476
25
±15.0
±67
±7.0
7.0
100
84
1,000
MG212S-05EI
12
10.8 - 13.2
205
15
5.0
400
40.0
12.0
220
81
500
MG212S-15EI
12
10.8 - 13.2
198
15
15.0
133
13.0
7.0
220
84
500
MG212D-15EI
12
10.8 - 13.2
198
15
±15.0
±67
±7.0
7.0
100
84
500
MG215D-15EI
15
13.5 - 16.5
157
10
±15.0
±67
±7.0
7.0
100
85
300
MG224S-05EI
24
21.6 - 26.4
101
8
5.0
400
40.0
12.0
220
82
250
MG224S-09EI
24
21.6 - 26.4
99
8
9.0
222
22.0
9.0
220
84
250
MG224S-15EI
24
21.6 - 26.4
99
8
15.0
133
13.0
7.0
220
84
250
MG224D-12EI
24
21.6 - 26.4
99
8
±12.0
±83
±8.0
8.0
100
84
250
MG224D-15EI
24
21.6 - 26.4
99
8
±15.0
±67
±7.0
7.0
100
84
250
Notes:
1. Output load regulation is specified for a load change of 10% to 100%.
2. When measuring output ripple, it is recommended that an external 1 µF ceramic capacitor & 10 µF electrolytic
capacitor be placed in parallel from the +Vout pin to the -Vout pin for single output models, or from each output
to common for dual output models.
3. Operation at no load will not damage these units, however, they may not meet all specifications.
4. These converters are specified for operation without external components. However, in some applications the
addition of input/output capacitors will enhance stability and reduce output ripple. The simple connection shown
below will typically meet EN 55022 Class B. For dual output units, a capacitor should be connected from each
output to common.
VIN
5 VDC
12 VDC
15 VDC
24 VDC
C1
4.7 µF/50V
2.2 µF/50V
2.2 µF/50V
1.0 µF/50V
C2
--470 pF/3 kV
470 pF/3 kV
470 pF/3 kV
L1
6.8 µH
6.8 µH
6.8 µH
6.8 µH
VOUT
5 VDC
9 VDC
12 VDC
15 VDC
±5 VDC
±12 VDC
±15 VDC
C3
10 µF
4.7 µF
2.2 µF
1.0 µF
4.7 µF
1.0 µF
0.47 µF
% Typ.
Derating Curve
Mechanical Dimensions
5. It is recommended that a fuse be used on the input of a power supply for
protection. See the Model Selection table above for the correct rating.
Pin Connections
Pin
Single
Dual
Pin
Single
Dual
1
-VIN
-VIN
9
No Pin
Common
7
NC
NC
10
-VOUT
-VOUT
8
+VOUT
+VOUT
14
+VIN
+VIN
NC = No Connection
MicroPower Direct
We Power Your Success - For Less!
292 Page Street Ste D Stoughton, MA 02072
•
TEL: (781) 344-8226
•
Notes:
• All dimensions are typical in inches (mm)
• Tolerance x.xx = ±0.02 (±0.50)
• Pin 1 is marked by a “dot” or indentation on the unit
FAX: (781) 344-8481
•
E-Mail: [email protected]