MG100xEI Series High Isolation, 1W Compact MiniDIP DC/DC Converters Electrical Specifications Specifications typical @ +25°C, nominal input voltage & rated output current, unless otherwise noted. Specifications subject to change without notice. Key Features: • 1W Output Power Input Parameter • Compact MiniDIP Case • 3,000 VDC Isolation Input Voltage Range • High Efficiency • Single and Dual Outputs Input Filter • >3.5 MHour MTBF Output • -40°C to +105°C Operation Parameter Output Voltage Accuracy • LOW COST Line Regulation, For VIN Change of 1% Load Regulation, See Note 1 Ripple & Noise (20 MHz) Temperature Coefficient Output Short Circuit Conditions Min. 3.3 VDC Input 2.97 5 VDC Input 4.50 12 VDC Input 10.80 15 VDC Input 13.50 24 VDC Input 21.60 Internal Capacitor Typ. 3.3 5.0 12.0 15.0 24.0 Max. 3.63 5.50 13.20 16.50 26.40 Units Conditions Typ. ±2.5 Max. Units % Min. 3.3 VOUT Models All Other Models See Model Selection Guide See Note 2 60 ±1.5 ±1.2 ±0.03 VDC % mV P - P %/°C Continuous (Autorecovery) General Parameter Isolation Voltage Isolation Resistance Isolation Capacitance Switching Frequency EMI Characteristics Parameter Conditions 60 Seconds 500 VDC 100 kHz, 0.1V Conditions EMC Compliance, Single Output EMC Compliance, Dual Output Typ. Max. 20 100 300 Units VDC M pF kHz Min. Conducted Radiated EMI Compliance, See Note 4 Min. 3,000 1,000 Electrostatic Discharge (ESD) Typ. Max. Units CISPR22/EN 55022 Level B CISPR22/EN 55022 Level B EN 61000-4-2 Level B Contact ±8 kV EN 61000-4-2 Level B Contact ±6 kV Environmental MicroPower Direct 292 Page Street Suite D Stoughton, MA 02072 USA Parameter Operating Temperature Range Storage Temperature Range Cooling Humidity Physical Case Size Case Material Weight Conditions Min. Typ. -40 +25 -55 Free Air Convection RH, Non-condensing Ambient Max. +105 +125 Units °C °C 95 % 0.787 x 0.394 x 0.276 Inches (20.0 x 10.0 x 7.0 mm) Non-Conductive Black Plastic (UL-94V0) 0.07 Oz (2.1g) Reliability Specifications Parameter MTBF Conditions MIL HDBK 217F, 25°C, Gnd Benign Min. 3.5 Typ. Max. Units MHours Conditions 3.3 VDC Input 5 VDC Input 12 VDC Input 15 VDC Input 24 VDC Input 1.5 mm From Case For 10 Sec Min. -0.7 -0.7 -0.7 -0.7 -0.7 Typ. Max. 5.0 9.0 18.0 21.0 30.0 300 Units Absolute Maximum Ratings T: (781) 344-8226 F: (781) 344-8481 E: [email protected] W: www.micropowerdirect.com Parameter Input Voltage Surge (1 Sec) Lead Temperature Caution: Exceeding Absolute Maximum Ratings may damage the module. These are not continuous operating ratings. www.micropowerdirect.com VDC °C www.micropowerdirect.com Model Selection Guide Model Number MG103S-03EI MG103S-05EI MG105S-03EI MG105S-05EI MG105S-12EI MG105S-15EI MG105S-24EI MG105D-05EI MG105D-12EI MG105D-15EI MG105D-24EI MG112S-03EI MG112S-05EI MG112S-12EI MG112S-15EI MG112S-24EI MG112D-05EI MG112D-12EI MG112D-15EI MG112D-24EI MG115S-05EI MG115S-15EI MG115D-05EI MG115D-15EI MG124S-03EI MG124S-05EI MG124S-12EI MG124S-15EI MG124S-24EI MG124D-05EI MG124D-12EI MG124D-15EI MG124D-24EI Input Voltage (VDC) Current (mA) Nominal Range Full-Load No-Load 3.3 2.97 - 3.63 415 30 3.3 2.97 - 3.63 388 30 5 4.50 - 5.50 267 20 5 4.50 - 5.50 250 20 5 4.50 - 5.50 250 20 5 4.50 - 5.50 247 20 5 4.50 - 5.50 247 20 5 4.50 - 5.50 253 20 5 4.50 - 5.50 252 20 5 4.50 - 5.50 252 20 5 4.50 - 5.50 249 20 12 10.8 - 13.2 111 15 12 10.8 - 13.2 104 15 12 10.8 - 13.2 104 15 12 10.8 - 13.2 103 15 12 10.8 - 13.2 103 15 12 10.8 - 13.2 105 15 12 10.8 - 13.2 105 15 12 10.8 - 13.2 103 15 12 10.8 - 13.2 103 15 15 13.5 - 16.5 83 10 15 13.5 - 16.5 84 10 15 13.5 - 16.5 83 10 15 13.5 - 16.5 82 10 24 21.6 - 26.4 55 7 24 21.6 - 26.4 53 7 24 21.6 - 26.4 51 7 24 21.6 - 26.4 51 7 24 21.6 - 26.4 51 7 24 21.6 - 26.4 53 7 24 21.6 - 26.4 51 7 24 21.6 - 26.4 52 7 24 21.6 - 26.4 52 7 Voltage Output Current (VDC) (mA, Max) 3.3 5.0 3.3 5.0 12.0 15.0 24.0 ±5.0 ±12.0 ±15.0 ±24.0 3.3 5.0 12.0 15.0 24.0 ±5.0 ±12.0 ±15.0 ±24.0 5.0 15.0 ±5.0 ±15.0 3.3 5.0 12.0 15.0 24.0 ±5.0 ±12.0 ±15.0 ±24.0 303 200 303 200 83 67 42 ±100 ±42 ±34 ±21 303 200 83 67 42 ±100 ±42 ±34 ±21 200 67 ±100 ±34 303 200 83 67 42 ±100 ±42 ±34 ±21 Notes: 1. Output load regulation is specified for a load change of 10% to 100%. 2. When measuring output ripple, it is recommended that an external 1 µF ceramic capacitor & 10 µF electrolytic capacitor be placed in parallel from the +Vout pin to the -Vout pin for single output models, or from each output to common for dual output models. 3. Operation at no load will not damage these units, however, they may not meet all specifications. 4. These converters are specified for operation without external components. However, in some applications the addition of input/output capacitors will enhance stability and reduce output ripple. The simple connection shown below will typically meet EN 55022 Class B. For dual output units, a capacitor should be connected from each output to common. Output Load Fuse Rating Regulation Capacitive Efficiency Slow-Blow Load (%, Typ) (mA) (mA, Min) % Typ. (µF Max) 31.0 18.0 220 73 750 20.0 12.0 220 78 750 31.0 18.0 220 75 750 20.0 12.0 220 80 750 9.0 8.0 220 80 750 7.0 7.0 220 81 750 5.0 6.0 220 81 750 ±10.0 12.0 100 79 750 ±5.0 8.0 100 80 750 ±4.0 7.0 100 81 750 ±3.0 6.0 100 81 750 31.0 18.0 220 75 250 20.0 12.0 220 80 250 9.0 8.0 220 80 250 7.0 7.0 220 81 250 5.0 6.0 220 81 250 ±10.0 12.0 100 80 250 ±5.0 8.0 100 80 250 ±4.0 7.0 100 81 250 ±3.0 6.0 100 81 250 20.0 12.0 220 80 200 7.0 7.0 220 81 200 ±10.0 12.0 100 80 200 ±4.0 7.0 100 81 200 31.0 18.0 220 75 100 20.0 12.0 220 79 100 9.0 8.0 220 81 100 7.0 7.0 220 81 100 5.0 6.0 220 81 100 ±10.0 12.0 100 79 100 ±5.0 8.0 100 81 100 ±4.0 7.0 100 81 100 ±3.0 6.0 100 81 100 Current Derating Curve Mechanical Dimensions VIN 3.3 VDC 5 VDC 12 VDC 15 VDC 24 VDC C1 4.7 µF/50V 4.7 µF/50V 4.7 µF/50V 4.7 µF/50V 4.7 µF/50V L1 6.8 µH 6.8 µH 6.8 µH 6.8 µH 6.8 µH VOUT 3.3 VDC 5 VDC 12 VDC 15 VDC 24 VDC ±5 VDC ±12 VDC ±15 VDC ±24 VDC C2 10 µF 10 µF 2.2 µF 1.0 µF 1.0 µF 4.7 µF 1.0 µF 0.47 µF 0.47 µF 5. It is recommended that a fuse be used on the input of a power supply for protection. See the Model Selection table above for the correct rating. Pin Connections Pin 1 7 8 Single -VIN NC +VOUT Dual -VIN NC +VOUT Pin 9 10 14 Single No Pin -VOUT +VIN Dual Common -VOUT +VIN NC = No Connection MicroPower Direct We Power Your Success - For Less! 292 Page Street Ste D Stoughton, MA 02072 • TEL: (781) 344-8226 • Notes: • All dimensions are typical in inches (mm) • Tolerance x.xx = ±0.02 (±0.50) • Pin 1 is marked by a “dot” or indentation on the unit FAX: (781) 344-8481 • E-Mail: [email protected]