PLANAR TRANSFORMERS HIGH FREQUENCY 150 WATT PP25D SERIES • • • • • • • • • Power Rating Up to 150 Watts High Efficiency of over 98% High Power Density of 600 Watts Per Cubic Inch Footprint 23.5 mm X 20.10 mm Lower Profile of 9.12 mm High Isolation (operational) 1500 Vdc High Frequency 200 kHz – 700 kHz Operating Temperature -40ºC to +125ºC Custom Design Available ELECTRICAL PARAMETERS @ 25°C Part Number PP25D- Primary Inductance (μH MIN) Leakage Inductance (μH MAX) 0802 151.0 0902 191.0 1002 DC Resistance Turns Ratio (mΩ MAX) Primary Secondary Primary Secondary Isolation (VDC) Figure A Aux 0.43 18.0 18.0 0.85 & 0.85 4T/4T 1T & 1T 1500 A 0.43 18.0 20.0 0.85 & 0.85 4T/5T 1T & 1T 1500 A 236.0 0.48 20.0 20.0 0.85 & 0.85 5T/5T 1T & 1T 1500 A 1102 286.0 0.55 20.0 25.0 0.85 & 0.85 5T/6T 1T & 1T 1500 A 1202 340.0 0.60 25.0 25.0 0.85 & 0.85 6T/6T 1T & 1T 1500 A 0803 151.0 0.43 18.0 18.0 1.70 & 1.70 4T/4T 2T & 1T 1500 B 0903 191.0 0.43 18.0 20.0 1.70 & 1.70 4T/5T 2T & 1T 1500 B 1003 236.0 0.48 20.0 20.0 1.70 & 1.70 5T/5T 2T & 1T 1500 B 1103 286.0 0.55 20.0 25.0 1.70 & 1.70 5T/6T 2T & 1T 1500 B 1203 340.0 0.60 25.0 25.0 1.70 & 1.70 6T/6T 2T & 1T 1500 B 0804 151.0 0.43 18.0 18.0 7.00 4T/4T 4T 1500 C 0904 191.0 0.43 18.0 20.0 7.00 4T/5T 4T 1500 C 1004 236.0 0.48 20.0 20.0 7.00 5T/5T 4T 1500 C 1104 286.0 0.55 20.0 25.0 7.00 5T/6T 4T 1500 C 1204 340.0 0.60 25.0 25.0 7.00 6T/6T 4T 1500 C NOTES: 1. The inductance is measured with both primary windings connected in series Pin (2--5) with Pin (3--4) shorted 2. The leakage inductance is measured in winding Pin (2 -4) with all other winding shorted 3. All specifications typical at TA=25°C Product performance is limited to specified parameters. Data is subject to change without prior notice. Tel: 310-325-1043 Fax: 310-325-1044 www.mpsind.com [email protected] PLANAR TRANSFORMERS HIGH FREQUENCY 150 WATT PP25D SERIES DIMENSIONS (mm) SUGGESTED PAD LAYOUT SCHEMATICS Figure A Figure B Product performance is limited to specified parameters. Data is subject to change without prior notice. Tel: 310-325-1043 Fax: 310-325-1044 Figure C Dimensions Unless otherwise specified, all tolerances are: inch: .XX : ±0.015 .XXX : ±0.004 mm: X,X : ±0,38 X,XX : ±0,10 www.mpsind.com [email protected]