SPB05 5W DC-DC Regulated Single Output Converter series ■ Features : ‧2:1 wide input range ‧1500VDC I/O isolation ‧Built-in remote ON/OFF control ‧Built-in EMI filter ‧Protections: Short circuit / Overload ‧Cooling by free air convection ‧Single in line package ‧100% full load burn-in test ‧Low cost / High reliability ‧Modified models available: output 3.3V/9V ‧2 years warranty SPECIFICATION SPB05A-05 ORDER NO. DC VOLTAGE CURRENT RANGE RIPPLE & NOISE (max.) Note.2 80mVp-p Note.3 ±0.5% LINE REGULATION LOAD REGULATION Note.4 ±0.5% VOLTAGE ACCURACY ±2.0% SWITCHING FREQUENCY 100KHz min. EXTERNAL CAPACITANCE LOAD (max.) 220uF A: 9 ~ 18VDC VOLTAGE RANGE SPB05C-12 SPB05A-15 12V 42 ~ 417mA 15V 33 ~ 333mA 90mVp-p 90mVp-p SPB05B-15 SPB05C-15 85% 85% C: 36 ~ 72VDC REMOTE CONTROL PROTECTION Power ON : R.C. ~ -Vin < 1VDC or open ; Power OFF : R.C. ~ -Vin > 4VDC or short Fuse recommended A: 1000mA B: 600mA C: 300mA Slow-Blow Type OVERLOAD 150 ~ 250% rated output power Protection type : Recovers automatically after fault condition is removed PROTECTION 85% 85% 84% All output equipped with short circuit SHORT CIRCUIT Protection type : Recovers automatically after fault condition is removed -40 ~ +80℃ (Refer to "Derating Curve") WORKING TEMP. WORKING HUMIDITY ENVIRONMENT SPB05B-12 FILTER DC CURRENT (Note. 5) B: 18 ~ 36VDC SPB05A-12 81% 83% 83% 85% Full load A: 515mA B: 250mA C: 125mA No load A: 40mA B: 25mA C: 15mA Capacitor Type EFFICIENCY (Typ.) INPUT SPB05C-05 5V 100 ~ 1000mA 5W RATED POWER OUTPUT SPB05B-05 20% ~ 90% RH non-condensing STORAGE TEMP., HUMIDITY -55 ~ +105℃, 10 ~ 95% RH ±0.05% / ℃ (0 ~ 55℃) TEMP. COEFFICIENT VIBRATION 10 ~ 500Hz, 2G 10min./1 cycle, period for 60min. each along X, Y, Z axes WITHSTAND VOLTAGE I/P-O/P:1.5KVDC SAFETY ISOLATION RESISTANCE ISOLATION CAPACITANCE I/P-O/P: 100M Ohms / 500VDC / 25℃/ 70% RH 80pF max. OTHERS EMC EMISSION EMC IMMUNITY MTBF DIMENSION Compliance to EN55022 Class B, FCC part 15 Class B Compliance to EN61000-4-2,3,4,5,6,8 light industry level, criteria A 600Khrs min. MIL-HDBK-217F(25℃) 21.8*9.2*11.1mm or 0.86"*0.36"*0.44" inch (L*W*H) WEIGHT 4.8g Unit:mm(inch) 21.8(0.86) FRONT VIEW 0.5±0.05(0.02) 2.54(0.1) 1 2 3 0.5 (0.02) 5 6 7 8 5.08 (0.2) 17.78(0.7) BOTTOM VIEW 2.4(0.09) Derating Curve Pin Configuration Mechanical Specification 3.81±0.5(0.15) Pin No. Output 1 2 3 5 6 7 8 -Vin + Vin R.C. N.C. + Vo u t - Vo u t N.C. 100 50 -40 0 25 50 60 80 100 2.01(0.08) Ta (℃) NOTE 1.All parameters are specified at normal input, rated load, 25℃ 70% RH ambient. 2.Ripple & noise are measured at 20MHz by using a 12" twisted pair terminated with a 0.1uf & 47uf capacitor. 3.Line regulation is measured from low line to high line at rated load. 4.Load regulation is measured from 10% to 100% rated load. 5.Please prevent the converter from operating in overload or short circuit condition for more than 30 seconds. File Name:SPB05-SPEC 2014-10-09