b.Push dim MEAN WELL's AC/DC LED PSU Dimming control mechanism DAP-04 Installation Manual AC/L AC source F 90 M M V+ AC/DC VLED PSU1 DIM+ AC/N DIM- ~ Lamp 1 Bau ar t gepr uft Si cherhei t eg el ma ge od o s be wac g SELV Pushing time <0.05 sec Turn ON/OFF 0.1~1 sec Dimming up or down 1.5~10 sec Setting light to 100% >11 sec ww w.t uv.co m ID 20000 00000 V+ AC/DC VLED PSU4 DIM+ AC/N DIMAC/L Features: •Universal AC input/Full range (up to 305V) •Convert DALI signal to PWM signal •4 DALI addressable output channels •Built-in push dim function •Comply with DALI standards (IEC62386-101,102,207) •Linear or logarithm dimming curve selectable (meet IEC62382-207) •PWM active high or active low selectable by jumper •Dimming range:1~100% •Fully isolated plastic case •Class Ⅱ power unit, no FG •IP20 design •Power consumption < 0.5W •3 years warranty •Built-in relay for ON/OFF control of MEAN WELL's AC/DC LED power supply Lamp 4 LED Light Fixture AC/L DIM1+ AC/N + DIM2 Push + DIM3 + DIM4 DAP-04 - Push dimmer •It will always dim up when light intensity is lower than 10%, whereas it will always dim down when light intensity is higher than 90% •Factory default dimming setting : 100% ※Note: Only use Normally Open Push Button without light indicator . Wiring: c.Dimming with LED PSU ON/OFF •Use wires with an adequate cross-section (see 3) Relay or magnetic switch •Use suitable mounting tools to do the wiring and mounting (see 3) •Use a Miniature Circuit Breaker (MCB) with an adequate current rating to protect the lighting system (see 4) AC source ~ + Environmental limitations: AC/L V+ AC/N V- MEAN WELL AC/DC LED PSU DIM+ Relay •Maximum ambient temperature must not exceed 60℃ Cautions: AC/N + DAP-04 manufacturers may be incompatible with the DAP-04 Settings and connections: 1.Terminal Block Pin Assignments LED Li ght Fixture DIM- AC/N Figure 1 DAP-04 •Only can be used with MEANWELL's LED Power Supply Units (PSUs) equipped with 3 in 1 dimming function. LED PSUs made by other V- MEAN WELL AC/DC LED PSU DIM+ Relay + DIM1 - •This unit must be installed by a qualified electrician + DIM1 - Figure 2 The DAP-04 is equipped with a relay that can be used to turn ON/OFF MEAN WELL LED PSUs. The relay is in the closed position when the DIM1 generates dimming signal; the relay is in the open position when there is no output signal on the DIM1. ※Note: An additional magnetic switch is needed when the total input current of the selected LED PSUs is higher than 8A or used with LED PSUs whose inrush current is greater than 50A, please refer to the figure 2. d.Synchronization operation Dimmi nga bl e AC/ L AC/ N PUSH DA+ DA- TB2 TB1 RY+ RY- D IM1+ D IM1D IM2+ D IM2D IM3+ D IM3D IM4+ D IM4- DIM+ ACT-HI AC/L Lamp 1 + + DIM1 + DIM2 - Dimmi nga bl e L ED p ow er L ED p ower DIM- Dimmi nga bl e Up t o 20 unit s DIM+ + DIM- DIM+ + L ED p ow er DIM- DIM+ + DIM- DAP-04 + DIM3 + DIM4 - MEAN WELL's AC/DC LED PSU V+ AC/DC VLED PSU1 DIM+ AC/N DIM- Dimmi nga bl e Up t o 20 unit s L ED p ower 2.Connection of Dimming Functions a.DALI ~ ~ AC/L AC/N V+ AC/L AC source LED Light Fixture DIM- AC/L •Only install the unit at indoor environments AC source Function No change of state Up to 4 channels The DAP-04 is equipped with 4 DALI channels, each channel can drive up to 20 LED PSUs, allowing a total of 80 LED PSUs to be connected to the DALI/PWM converter. (Each channel is individually addressable, light intensity of LED PSUs connected to the same channel will be the same; the maximum allowable voltage drop between the DAP-04 and LED PSUs should not be higher than 0.5V; Maximum cable length for 1.31mm 2 cables is 300m.) ※Note: Light intensity of LEDs in the same group may be decreased when one of the LED PSUs is AC OFF. 3.Recommended Screwdriver, Wire and Torque Setting Type AC/L V+ AC/DC VLED PSU4 DIM+ AC/N DIM- DALI Bus DALI c ontroller AC/L DIM1+ AC/N + DIM2 DALI+ + DALI- DIM3 + DIM4 DAP-04 Lamp 4 LED Light Fixture The cover (the blue ones) TB1(ACL/N,PUSH,DALI±,RY±) ψ1.02mm-ψ1.628mm Stranded wire 0.823-2.08mm American wire gauge 14-18AWG 16-18AWG Wire stripping length 10mm(0.39") 10mm(0.39") 3mm Slotted 3mm Slotted 3-4kp(6.61-8.81lb F) 3-4kp(6.61-8.81lb F) Screwdriver 5mm Phillips Recommended tightening torque 4.6kgf-cm(4lb-in) Suggested push-down strength Up to 4 channels ※Note: Choose a suitable cable for connecting the DAP-04 and DALI controller and make sure the maximum voltage drop between these two units should not be higher than 2V. (Maximum cable length for 1.5mm 2 cables is 300m.) TB2(DIM1±,2±,3±,4±) Solid wire 2 ψ1.02mm-ψ1.29mm 0.823-1.31mm 2 4.Suggested Maximum Number of the DAP-04 Units that can be Connected to a MCB at 230Vac Model B10 B16 C10 C16 DAP-04 10 16 17 27 ※Note: These calculated values are based on MCB S201 series manufactured by ABB. MEAN WELL ENTERPRISES CO., LTD. No.28, Wuquan 3rd Rd., Wugu Dist., New Taipei City 248, Taiwan (R.O.C.) http://www.meanwell.com Version 0 b.按壓調光 明緯AC/DC LED電源 DAP-04安裝使用手冊 調光控制操作 交流電源 F 90 M M AC/L 交流/直流 LED 電源1 AC/N ~ V+ VDIM+ DIM- 燈具1 Bau ar t gepr uft Si cherhei t eg el ma ge od o s be wac g SELV 功能 按壓時間 無動作 <0.05秒 開關 0.1~1秒 調光 1.5~10秒 重置 >11秒 ww w.t uv.co m ID 20000 00000 AC/L 交流/直流 LED 電源4 AC/N ㈵色 : •90~305VAC交流輸入 •DALI訊號轉PWM訊號 •四組可定址DALI輸出通道 • 內建按壓 調光(PUSH DIM)功能 •符合DALI規範(IEC62386-101,102,207) •可選擇線性或對數調光模式(符合IEC62386-207規範) •可選擇PWM輸出的邏輯準位 •絕緣塑膠外殼 •調光範圍:1~100% •IP20等級 •消耗瓦數<0.5W •三年保固 •內建繼電器可對所搭接之MW交流/直流LED電源供應器作開/關控制 燈具4 •當亮度小於10%時，亮度僅能往上調亮。當調光亮度大於90%時， 亮度僅能往下調暗 LED燈組 AC/L DIM1+ AC/N + DIM2 Push + DIM3 + DIM4 DAP-04 - •Class Ⅱ 電源，無FG 接線 : V+ VDIM+ DIM- 按壓開關 • 出廠預設亮度為全亮(100%) ※請注意僅能使用無指示燈的按鈕開關。 •配線時請使用建議的線材(請參考第3項) c.調光加㆖ON/OFF功能 • 配線時 請 使用建議工具(請參考第3項) 繼電器或電磁閥 •請選用適當電流容量的MCB(miniature circuit breaker)，可以保護整個照明系統(請參考第4項) ~ 交流電源 使用環境 : + • 最高環境溫度 請勿 超過60℃ •只限 用於 室內環境 AC/L V+ AC/N V- 繼電器 • 本產品僅能由合格的電氣 工程人員安裝 ~ AC/N + 繼電器 + DIM1 - DAP-04 1.端子台腳位定義 圖1 DAP-04 + DIM1 - 圖2 d.同步操作功能 AC/ L AC/ N PUSH D A+ D A- TB2 TB1 R Y+ R Y- 三 合一 可 調光 DIM1+ DIM1DIM2+ DIM2DIM3+ DIM3DIM4+ DIM4- DIM+ ACT-HI AC/L 交流/直流 LED 電源1 AC/N AC/L 交流/直流 LED 電源4 AC/N DALI匯流排 V+ VDIM+ DIM- 燈具 1 AC/L DIM1+ AC/N + DIM2 DALI+ + DALI- DIM3 + DIM4 DAP-04 燈具 4 LED燈組 DIM- DIM+ + DIM- ※請注意DALI控制線長度選用，應確保DALI控制器與最遠的DAP-04之線壓降須小於2V;使用1.5mm 2線材時，最長可為300公尺。 + DIM- LE D電源 DIM+ + DIM- 最多可接4組 3.建議的安裝線材與工具 側蓋(藍色) TB1(ACL/N,PUSH,DALI±,RY±) TB2(DIM1±,2±,3±,4±) 單芯 線 ψ1.02mm-ψ1.628mm ψ1.02mm-ψ1.29mm 多芯 絞線 0.823-2.08mm 2 0.823-1.31mm 2 美規線 14-18AWG 16-18AWG 剝線長度 10mm(0.39") 10mm(0.39") 3mm 一字 3mm 一字 3-4kp(6.61-8.81lb F) 3-4kp(6.61-8.81lb F) 安裝工具 5mm 十字 建議鎖附力矩 4.6kgf-cm(4lb-in) 建議按壓力矩 最多可接4組DALI定址通道 DIM+ 三 合一 可 調光 最多可 接2 0組 DAP-04內建4組通道，每個通道最多可連接20台明緯LED電源，四個通道最多共可接80台明緯LED電源。 2 (每個通道皆可獨立控制，接在同一組通道的明緯LED電源的亮度一致，DAP-04與LED電源的連接線壓降應小於0.5V;使用1.31mm 線材 時，最長可為300公尺。) ※請注意當其中一台LED電源市電OFF時，可能會導致其他LED電源輸出調光亮度下降。 型式 V+ VDIM+ DIM- 三 合一 可 調光 LE D電源 DAP-04 + DIM3 + DIM4 - 明緯AC/DC LED電源 + + DIM1 + DIM2 - 三 合一 可 調光 LE D電源 最多可 接2 0組 LE D電源 2.調光功能的連接方式 a.DALI調光 DALI 控制器 LED燈組 DAP-04內建繼電器可以開/關明緯的LED電源，當DIM1調光輸出時，繼電器為接合狀態，當DIM1無輸出時，繼電器為開路狀態。 ※請注意當選用的明緯LED電源的輸入電流大於8A，或是湧浪電流大於50A的機型，內建繼電器需搭配額外電磁開關使用(參考 圖2)。 設定與連接 : ~ V- 明緯 交流/直流LED 電源 DIM+ DIM- AC/N •DAP-04搭配之LED電源僅能是明緯具三合一可調光之機種，無法與其它LED電源品牌產品搭用 交流電源 - AC/L AC/N ㊟意事㊠ : 交流電源 LED燈組 DIM- AC/L V+ AC/L 明緯 交流/直流LED 電源 DIM+ 4.於230V在同㆒個MCB迴路㆘，建議最大的安裝台數 型式 B10 B16 C10 C16 DAP-04 10 16 17 27 ※此計 算參 數皆以ABB S201估算 。 明緯 企業 股份有 限公司 248 新 北市 五股區 五權三 路28號 http://www.meanwell.com 版 本0