Digital E3 Modulevel® Liquid Level Displacer Transmitter D E S C R I P T I O N The Digital E3 Modulevel® is an advanced, intrinsically safe two-wire instrument utilizing simple buoyancy principle to detect and convert liquid level changes into a stable output signal. The linkage between the level sensing element and output electronics provides a simple mechanical design and construction. The vertical in-line design of the transmitter results in low instrument weight and simplified installation. The instrument comes in a variety of configurations and pressure ratings for varied applications. The Digital E3 MODULEVEL has microprocessor-based electronics with 4 –20 mA/HART® or FOUNDATION fieldbus™ output. E3 supports the FDT/DTM standard and a PACTware™ PC software package allows for additional configuration and trending capabilities. T E C H N O L O G Y Changing buoyancy forces caused by liquid level change act upon the spring supported displacer causing vertical motion of the core within a linear variable differential transformer. As the core position changes with liquid level, voltages are induced across the secondary windings of the LVDT. These signals are processed in the electronic circuitry and converted to a useable output signal. The enclosing tube acts as a static isolation barrier between the LVDT and the process media. A P P L I C A T I O N S MEDIA: Liquids or slurries, clean or dirty, light hydrocarbons to heavy acids (SG=0.23 to 2.20) VESSELS: Process & storage, bridles, bypass chambers, interface, sumps & pits up to unit pressure & temperature ratings. CONDITIONS: Most liquid level measurement and control applications including those with varying dielectric, vapors, turbulence, foam, buildup, bubbling or boiling and high fill/empty rates. Also, liquid/liquid interface level measurement or density control. F E A T U R E S • Two-wire, loop-powered, transmitter for level, interface or density measurement • No level change needed for configuration; no field calibration necessary. • Non-interacting zero and span • Emission and immunity compliance to EN 61326 • Specific gravity adjustment without stopping process • Signal damping adjustment • Safety Integrity Level (SIL) value of 2, SFF value of 92.3% • 15-unit multi-drop capability • 4 –20 mA output signal • Two-line, 8-character LCD and 3-button keypad • Continuous self-test with 22 mA, 3.6 mA or Hold fault indication fully compliant with NAMUR NE 43 • Comprehensive diagnostics with faults, warnings & status history • HART or FOUNDATION fieldbus digital communications • PACTware PC program using HART communication for advanced configuration and troubleshooting (see bulletin 59-101) • IS, XP and Non-incendive approvals by FM, CSA, ATEX, IEC I N T E R F A C E E3 MODULEVEL is capable of tracking the interface level of two immiscible liquids with different densities. Each unit is custom-made with a displacer specially designed for the user’s application. This allows it to detect the position of a clean interface or an emulsion layer and convert it into a stable 4 –20 mA signal. Contact the factory for assistance in specifying an E3 for interface service. Note that for proper interface detection, the entire displacer must always be immersed in liquid. D E N S I T Y • Standard output range from 3.8 to 20.5 mA • 11 VDC turn on voltage • Maximum loop resistance of 620 ohms at 24 VDC • Process temperatures to +600° F (+315° C) for non-steam applications • Level ranges from 14 to 120+ inches (356 to 3048+ mm) • Specific gravity as low as 0.23 • Cast aluminum or stainless steel, TYPE 4X, Cl I Div 1 Groups B, C, D housing • Field wiring in isolated junction box • Head rotatable through 360° • Accepted proven LVDT/range spring technology • Range spring suppresses effects of turbulence to produce stable output signal. • Flanged top mounting or external cage with side/side or side/bottom connections • Special options, materials of construction and custom engineered features available (consult factory). • Spring protector standard • Signal sampling 15 times per second 2 Yet another capability of E3 MODULEVEL is to track the changing density of a liquid over a known density range and convert that into a stable 4–20 mA output signal. As the density of the liquid changes, so does the mass of the liquid displaced by the specially designed displacer. The resulting change in buoyancy force on the displacer causes the movement of the LVDT core necessary to convert the density change to the 4–20 mA signal. PACTware™ P C S O F T W A R E PACTware PC software and the Field Device Tool (FDT) standard take level measurement to a new degree of setup efficiency and user-friendliness. PACTware adds a graphical software interface for increased ease of use. Simply connect your PC through a serial interface to the HART loop and all functionality can be accessed conveniently, and safely. Refer to Magnetrol® PACTware bulletins 59-101 & 59-601 for more information. S P E C I F I C A T I O N S F U N C T I O N A L System Design Measurement Principle Buoyancy – continuous displacement utilizing a precision range spring Input Measured Variable Level, determined by LVDT core movement affected by Physical Range Up to 120" (300 cm) based on displacer length (consult factory for longer ranges) buoyancy force changes on continuous displacer Output Type 4 to 20 mA with HART Version 5.x 3.8 to 20.5 mA useable (meets NAMUR NE 43) FOUNDATION fieldbus, H1 (31.25 kbits⁄sec), Available blocks AI_1, PID_1, RB_1, TB_1 LAS capable, ITK 5.0 interoperability tested Resolution Analog: 0.01 mA, Display: 0.1%, Level Units: 0.01 inch Loop Resistance (maximum) 620 ohms @ 24 VDC Diagnostic Alarm 3.6, 22 mA or HOLD selectable (meets NAMUR NE 43) Damping Adjustable 0-45 seconds Sampling Rate Transmitter 15 times per second User Interface Keypad Indication 3-button menu-driven data entry and system security 2-line × 8-character LCD display Power Measured at instrument terminals 11 to 36 VDC FOUNDATION fieldbus (Direct Current) HART, 9 to 32 VDC This device provides only Functional Isolation. Current 22.5 mA maximum HART, 17 mA (maximum current draw) FOUNDATION fieldbus This device provides only Functional Isolation. Housing Material Aluminum A356-T6 (<0.20% copper), optional 316 stainless steel Cable Entry 3 Ingress Protection TYPE 4X, IP66 ⁄4" NPT and M20 Chamber Materials Carbon steel Wetted parts 316/316L and Inconel® (spring) Process connections Tank Top: 3", 4", 6" ANSI Flange Chambered: 11⁄2", 2" NPT, Socketweld, ANSI Flanges 316/316L stainless steel Process Conditions Process temperature range Steam applications: -20° to +500° F (-29° to +260° C) Process pressure range 5150 psig @ +100° F (355 bar @ +38° C) Non-steam applications: -20° to +600° F (-29° to +315° C) Environment Electronics Operating Temperature -40 to +176° F (-40 to +80° C) Display Function Operating Temperature -5 to +160° F (-20 to +70° C) Storage Temperature -50 to +185° F (-40 to +85° C) Humidity 0-99%, non-condensing Electromagnetic Compatibility Meets CE Requirement: EN 61326 Shock Class Vibration Class ANSI/ISA-S71.03 Class SA1 ANSI/ISA-S71.03 Class VC2 Altitude ≤2000 m Pollution Degree 2 Maximum process temperatures are based on ambient temperatures less than or equal to +120° F (+49° C). Higher ambient temperatures require reduced process temperatures. Consult factory for low temperature applications down to -330° F (-200° C) With aluminum housing only. Does not apply to models with 316 SS transmitter housings. 3 S P E C I F I C A T I O N S P E R F O R M A N C E : L E V E L Reference Conditions Water @ +70° F (+21° C) with 14" displacer, wet calibration Linearity ±0.20% of full span Repeatability ±0.05% of full span Ambient temperature effect Maximum zero shift is 0.017%/°F over ambient temperature range Operating Temp. range: -40° to +176° F (-40° to +80° C) LCD Temp. Range: -5° to +160° F (-20° to +70° C) Hysteresis ±0.20% of full span Response Time <1 second Warm-up Time <5 seconds SIL Suitable for use in SIL 2 environments with SFF of 92.3% P E R F O R M A N C E : I N T E R F A C E L E V E L D E N S I T Y & Linearity ±0.70% of full span Repeatability ±0.40% of full span Ambient temperature effect Maximum zero shift is 0.017%/°F over ambient temperature range 1200 Allowable Loop Resistance vs. Supply Voltage The displacer must always be completely immersed in process liquid when the E3 is used in interface or density service. Top mounted models require liquid level to exceed the top of the displacer by 2" at all times to ensure optimal performance. 20.5 mA 1000 Ω 800 620 600 400 200 24 VDC 0 A G E N C Y A P P R O V A L S AGENCY MODEL FM XEXX-XXXX with transmitter codes: 11 0 10 20 30 40 VDC APPROVAL x11, x12, x13, x14 x21, x22, x23, x24 x31, x32, x33, x34 Explosion Proof Class I, Div. 1; Groups B, C, D Class II, Div. 1; Groups E, F, G x41, x42, x43, x44 Class III, T5 x51, x52, x53, x54 Type 4X, IP66 x61, x62, x63, x64 XEXX-XXXX with transmitter codes: x15, x16, x17, x18 x25, x26, x27, x28 x35, x36, x37, x38 x45, x46, x47, x48 XEXX-XXXX with transmitter codes: Class II, Div. 1; Groups E, F, G Class III, T4 x55, x56, x57, x58 Entity x65, x66, x67, x68 Type 4X, IP66 x11, x12, x13, x14 Class I, Div. 2; Groups A, B, C, D x21, x22, x23, x24 x31, x32, x33, x34 Non-Incendive Class II, Div. 2; Groups E, F, G x41, x42, x43, x44 Class III, Div. 2; T4 x51, x52, x53, x54 Type 4X, IP66 x61, x62, x63, x64 4 Intrinsically Safe Class I, Div. 1; Groups A, B, C, D A G E N C Y A P P R O V A L S AGENCY MODEL CSA XEXX-XXXX with transmitter codes: APPROVAL x11, x13 x21, x23 x31, x33 Explosion Proof Class I, Div. 1; Groups B, C, D Class II, Div. 1; Groups E, F, G x41, x43 Class III, T5 x51, x53 Type 4X, IP66 x61, x63 XEXX-XXXX x15, x17 with transmitter codes: x25, x27 x35, x37 x45, x47 x55, x57 XEXX-XXXX with transmitter codes: Intrinsically Safe Class I, Div. 1; Groups A, B, C, D Class II, Div. 1; Groups E, F, G Class III, T4 Entity x65, x67 Type 4X, IP66 x11, x13 Suitable for: x21, x23 x31, x33 Class I, Div. 2; Groups A, B, C, D Class II, Div. 2; Groups E, F, G x41, x43 Class III, T4 x51, x53 Type 4X, IP66 x61, x63 ATEX XEXX-XXXX, EXX-XXXX x1E, x1F, x1G, x1H Flameproof with transmitter codes x2E, x2F, x2G, x2H ATEX Ex II 1/2 G Ex d IIC T6 x3E, x3F, x3G, x3H EN 60079-0, EN 60079-1, EN 60079-26 94/9/EC Intrinsically Safe XEXX-XXXX, EXX-XXXX x1A, x1B, x1C, x1D with transmitter codes x2A, x2B, x2C, x2D ATEX Ex II 1 G Ex ia IIC T4 x3A, x3B, x3C, x3D EN 60079-0, EN 60079-11, EN 60079-26, EN 60079-27 94/9/EC XEXX-XXXX, EXX-XXXX x1A, x1B, x1C, x1D Non-Sparking with transmitter codes x2A, x2B, x2C, x2D ATEX Ex II 3 G Ex ic II T6 x3A, x3B, x3C, x3D EN 60079-0 EN 60079-11 94/9/EC IEC XEXX-XXXX, EXX-XXXX with transmitter codes x1E, x1F, x1G, x1H Flameproof x2E, x2F, x2G, x2H IECEx Ex d IIC T6 Ga/Gb x3E, x3F, x3G, x3H IEC 60079-0, IEC 60079-1, IEC 60079-26 XEXX-XXXX, EXX-XXXX with transmitter codes x1A, x1B, x1C, x1D Intrinsically Safe x2A, x2B, x2C, x2D IECEx Ex ia IIC T4 Ga x3A, x3B, x3C, x3D IEC 60079-0, IEC 60079-11, IEC 60079-26, IEC 60079-27 See appropriate Installation & Operating Manual for entity parameters for IS installation. On remote electronics housing only, seal is required within 18 inches. These units have been tested to EN 61326 and are in compliance with the EMC Directive 2004/108/EC. 5 D I M E N S I O N A L STANDARD I N C H E S PRESSURE S P E C I F I C A T I O N S MODELS E3A, E3B, E3C, E3D, E3E, E3F ( M M ) 4.02 (102) 4.02 (102) ¾" NPT Dual Conduit Entries ¾" NPT Dual Conduit Entries 4.02 (102) ¾" NPT Dual Conduit Entries A A ANSI standard flange B D C 0.87 (22) 2.81 (71) 3.86 (98) Level range 3.95 (100) H 10.32 (262) J 8.10 (206) 4.04 (103) E 70° Dia. F HT Integral Side/Bottom Mount Fourth Digit Codes A, B, C E3A/E3B Series with Integral Top Mounting Fourth Digit Codes J, K, L Integral Transmitter Head 2.84 502 (72) (128) 3.99 (101) ¾" NPT Dual Conduit Entries 10.32 (262) A minus 3.34 (85) 3.85 (98) A minus 3.34 (85) D Level range Level range G G E F 1" NPT drain (plug not provided) Remote Side/Side Mount Fourth Digit Codes A, B, C 5.31 (135) 45° 6.25 (159) D 4.02 (102) 3.96 (101) 8.73 (222) 15.95 (405) 6 6.28 (159) 5.42 (138) 6.48 (165) 2.39 (61) Up to 75' (23 m) of connecting cable part number 037-3226-0XX or 037-3227-0XX, run in conduit. Last 2 digits in part number are cable length in feet. Cable must be ordered separately. E F 1" NPT drain (plug not provided) Remote Side/Side Mount Fourth Digit Codes A, B, C 15.95 (405) D I M E N S I O N A L I N C H E S S P E C I F I C A T I O N S ( M M ) Cage Pressure Rating Process Conn. Size Dimension Spring S.G. Range B C D E F G H J 0.23 – 0.54 6.75 (171) 9.31 (236) 9.31 (236) 3.19 (81) 7.00 (178) 3.00 (76) 3.00 + range (76 + range) 5.43 (138) 0.55 – 1.09 4.75 (121) 7.31 (186) 7.31 (186) 3.19 (81) 7.00 (178) 3.00 (76) 3.00 + range (76 + range) 5.43 (138) 1.10 – 2.20 4.75 (121) 7.31 (186) 7.31 (186) 3.19 (81) 7.00 (178) 3.00 (76) 3.00 + range (76 + range) 5.43 (138) 0.23 – 0.54 6.75 (171) 9.31 (236) 9.31 (236) 3.31 (84) 7.13 (181) 3.00 (76) 3.00 + range (76 + range) 5.43 (138) 0.55 – 1.09 4.75 (121) 7.31 (186) 7.31 (186) 3.31 (84) 7.13 (181) 3.00 (76) 3.00 + range (76 + range) 5.43 (138) 1.10 – 2.20 4.75 (121) 7.31 (186) 7.31 (186) 3.31 (84) 7.13 (181) 3.00 (76) 3.00 + range (76 + range) 5.43 (138) 11⁄2" 0.55 – 1.09 6.75 (171) 9.31 (236) 9.31 (236) 3.19 (81) 7.00 (178) 3.00 (76) 3.00 + range (76 + range) 5.43 (138) 2" 0.55 – 1.09 6.75 (171) 9.31 (236) 9.31 (236) 3.31 (84) 7.13 (181) 3.00 (76) 3.00 + range (76 + range) 5.43 (138) 11⁄2" 0.55 – 1.09 6.75 (171) 9.31 (236) 9.31 (236) 3.19 (81) 7.00 (178) 3.44 (87) 3.44 + range (87 + range) 6.43 (163) 2" 0.55 – 1.09 6.75 (171) 9.31 (236) 9.31 (236) 3.31 (84) 8.13 (207) 3.44 (87) 3.44 + range (87 + range) 7.43 (189) 11⁄2" 0.55 – 1.09 6.75 (171) 9.31 (236) 9.31 (236) 4.00 (102) 9.00 (229) 3.44 (87) 3.44 + range (87 + range) 10.21 (259) 2" 0.55 – 1.09 6.75 (171) 9.31 (236) 9.31 (236) 4.38 (111) 9.81 (249) 3.44 (87) 3.44 + range (87 + range) 11.08 (281) 11⁄2" 150#, 300# & 600# ANSI 2" 900# ANSI 1500# ANSI 2500# ANSI “A” Dimension Cage Press. Rating Fourth Digit of Model Number Head Flange Size 3" 150# ANSI 4" 6" 3" 300# ANSI 4" 6" 3" 600# ANSI 4" 6" 3" 900# ANSI 4" 6" 3" 1500# ANSI 4" 6" 4" 2500# ANSI 6" A, B, C D, E, F J, K, L M, N, P 16.97 (431) 16.97 (431) 17.03 (433) 17.16 (436) 17.28 (439) 17.47 (444) 17.53 (445) 17.78 (452) 18.16 (461) 17.78 (452) 18.03 (458) 18.47 (469) 18.16 (461) 18.41 (468) 19.53 (496) 19.28 (490) 20.53 (521) 24.97 (634) 24.97 (634) 25.03 (636) 25.16 (639) 25.28 (642) 25.47 (647) 25.53 (648) 25.78 (655) 26.16 (664) 25.78 (655) 26.03 (661) 26.47 (672) 26.16 (664) 26.41 (671) 27.53 (699) 27.28 (693) 28.53 (725) 12.97 (329) 12.97 (329) 13.03 (331) 13.16 (334) 13.28 (337) 13.47 (342) 13.53 (344) 13.78 (350) 14.16 (360) 13.78 (350) 14.03 (356) 14.47 (368) 14.16 (360) 14.41 (366) 15.53 (394) 15.28 (388) 16.53 (420) 20.97 (533) 20.97 (533) 21.03 (534) 21.16 (537) 21.28 (541) 21.47 (545) 21.53 (547) 21.78 (553) 22.16 (563) 21.78 (553) 22.03 (560) 22.47 (571) 22.16 (563) 22.41 (569) 23.53 (598) 23.28 (591) 24.53 (623) 7 N O N - S T E A M M O D E L S E R V I C E N U M B E R Models available for quick shipment, usually within one week after factory receipt of a complete purchase order, through the Expedite Ship Plan (ESP). DESIGN TYPE E3 Standard Construction Electronic MODULEVEL MOUNTING AND CHAMBER MATERIALS Flanged top steel 316 SS A B Cage side/bottom 316 SS steel C D Cage side/side 316 SS steel E F Adjustable 8-foot hanger cable, part number 32-3110-001, required when distance from flange face to top of displacer must be greater than 7.31". Bolting material is alloy steel. SPECIFIC GRAVITY AND PROCESS TEMPERATURE 1&4 Integral or Remote 1&4 1&4 1&4 Transmitter Mounting Use with Mounting/Temp. codes (9th Digit) 3&6 +300° F +400° F +450° F +550° F +600° F maximum process temperature (+150° C) (+200° C) (+230° C) (+290° C) (+315° C) J K L A B C M N P D E F M N P 0.23 – 0.54 specific gravity (up to 600 lbs) 0.55 – 1.09 specific gravity (all pressures) 1.10 – 2.20 specific gravity (up to 600 lbs) PROCESS CONNECTION SIZE & TYPE External Cage 11⁄2" 2" A E R F P Q 3" n/a n/a G Top Mount 4" n/a n/a H Type 6" n/a n/a K NPT SW Flange CHAMBER PRESSURE CLASS ANSI Flange rating 150# RF 3 300# RF 4 600# RF 5 900# RF 6 1500# RF 2500# RF 7 8 Pressure rating limited by enclosing tube to 5150 psi @ +100° F For stainless steel construction on 1500# and 2500# models, consult factory Models E3A and E3B with 2500# construction must have a mounting flange 4" or greater LEVEL RANGE 14 356 A All Pressures 32 48 813 1219 B C 60 1524 D 72 1829 E 600# and below 84 96 108 2134 2438 2743 F G H 120 3048 I TRANSMITTER – ELECTRONICS (see opposite page) E 8 3 Inches mm Code N O N - S T E A M M O D E L S E R V I C E N U M B E R OUTPUT/SIL RATING H F 4-20 mA/HART, SIL 2 FOUNDATION fieldbus Digital Communications (English only) MOUNTING/TEMPERATURE Integral Mount Maximum Process Temperature 1 +550° F (+290° C) 3 +551° to +600° F (+291° to +315° C) Remote Mount (FM & CSA only) Maximum Process Temperature 4 6 +550° F (+290° C) +551° to +600° F (+291° to +315° C) Use with Specific Gravity and Process Temperature codes (4th Digit): J, K, L, A, B, C, M, N, P, D, E, F M, N, P Use with Specific Gravity and Process Temperature codes: J, K, L, A, B, C, M, N, P, D, E, F M, N, P HOUSING MATERIAL/CONDUIT ENTRY/APPROVAL Housing Material/Conduit Entry/Approval 1 Cast aluminum, FM/CSA XP, 3⁄4" NPT 2 Cast aluminum, FM XP, M20 3 Cast stainless steel, FM/CSA XP, 3⁄4" NPT 4 Cast stainless steel, FM XP, M20 5 Cast aluminum, FM/CSA IS, 3⁄4" NPT 6 Cast aluminum, FM IS, M20 7 Cast stainless steel, FM/CSA IS, 3⁄4" NPT 8 Cast stainless steel, FM IS, M20 A Cast aluminum, ATEX/IEC IS, 3⁄4" NPT B Cast aluminum, ATEX/IEC IS, M20 C Cast stainless steel, ATEX/IEC IS, 3⁄4" NPT D Cast stainless steel, ATEX/IEC IS, M20 E Cast aluminum, ATEX/IEC XP, 3⁄4" NPT F Cast aluminum, ATEX/IEC XP, M20 G Cast stainless steel, ATEX/IEC XP, 3⁄4" NPT H Cast stainless steel, ATEX/IEC XP, M20 9th Digit 1,3,4,6 1,3,4,6 1,3,4,6 1,3,4,6 1,3,4,6 1,3,4,6 1,3,4,6 1,3,4,6 1,3 1,3 1,3 1,3 1,3 1,3 1,3 1,3 E3X-XXXX (see previous page) E 3 9 S T E A M M O D E L S E R V I C E N U M B E R DESIGN TYPE E3 Standard Construction Electronic MODULEVEL MOUNTING AND CHAMBER MATERIALS Flanged top steel 316 SS A B Cage side/bottom 316 SS steel C D Cage side/side 316 SS steel E F Adjustable 8-foot hanger cable, part number 32-3110-001, required when distance from flange face to top of displacer must be greater than 7.31". Bolting material is alloy steel. SPECIFIC GRAVITY AND PROCESS TEMPERATURE Integral or Integral Remote Remote 1&4 2 5 +300° F +400° F +400° F (+150° C (+200° C) (+200° C) K B K Integral or Integral Remote Transmitter Mounting Remote 2&5 3 6 Use with Mounting/Temp. codes (9th Digit) +450° F +500° F +500° F maximum process temperature (+230° C) (+260° C) (+260° C) N E N 0.55 - 1.09 specific gravity (all pressures) PROCESS CONNECTION SIZE & TYPE External Cage 11⁄2" 2" A E R F P Q 3" n/a n/a G Top Mount 4" 6" n/a n/a n/a n/a H K Type NPT SW Flange CHAMBER PRESSURE CLASS ANSI Flange rating 150# RF 3 300# RF 4 600# RF 5 900# RF 6 1500# RF 2500# RF 7 8 Pressure rating limited by enclosing tube to 5150 psi @ +100° F For stainless steel construction on 1500# and 2500# models, consult factory Models E3A and E3B with 2500# construction must have a mounting flange 4" or greater LEVEL RANGE 14 356 A All Pressures 32 48 813 1219 B C 60 1524 D 72 1829 E 600# and below 84 96 108 2134 2438 2743 F G H 120 3048 I TRANSMITTER – ELECTRONICS (see opposite page) E 10 3 Inches mm Code S T E A M M O D E L S E R V I C E N U M B E R OUTPUT/SIL RATING H F 4-20 mA/HART, SIL 2 FOUNDATION fieldbus Digital Communications (English only) MOUNTING/TEMPERATURE Integral Mount Maximum Process Temperature 1 +300° F (+150° C) 2 +301° to +450° F (+151° to +230° C) 3 +451° to +500° F (+231° to +260° C) Remote Mount (FM & CSA only) 4 5 6 Use with Specific Gravity and Process Temperature codes (4th Digit): K B, N E Maximum Process Temperature Use with Specific Gravity and Process Temperature codes (4th Digit): +300° F (+150° C) +301° to +450° F (+151° to +230° C) +451° to +500° F (+231° to +260° C) K B, K, N E, N HOUSING MATERIAL/CONDUIT ENTRY/APPROVAL Housing Material/Conduit Entry/Approval 1 Cast aluminum, FM/CSA XP, 3⁄4" NPT 2 Cast aluminum, FM XP, M20 3 Cast stainless steel, FM/CSA XP, 3⁄4" NPT 4 Cast stainless steel, FM XP, M20 5 Cast aluminum, FM/CSA IS, 3⁄4" NPT 6 Cast aluminum, FM IS, M20 7 Cast stainless steel, FM/CSA IS, 3⁄4" NPT 8 Cast stainless steel, FM IS, M20 A Cast aluminum, ATEX/IEC IS, 3⁄4" NPT B Cast aluminum, ATEX/IEC IS, M20 C Cast stainless steel, ATEX/IEC IS, 3⁄4" NPT D Cast stainless steel, ATEX/IEC IS, M20 E Cast aluminum, ATEX/IEC XP, 3⁄4" NPT F Cast aluminum, ATEX/IEC XP, M20 G Cast stainless steel, ATEX/IEC XP, 3⁄4" NPT H Cast stainless steel, ATEX/IEC XP, M20 9th Digit 1,2,3,4,5,6 1,2,3,4,5,6 1,2,3,4,5,6 1,2,3,4,5,6 1,2,3,4,5,6 1,2,3,4,5,6 1,2,3,4,5,6 1,2,3,4,5,6 1,2,3 1,2,3 1,2,3 1,2,3 1,2,3 1,2,3 1,2,3 1,2,3 E3X-XXXX (see previous page) E 3 11 Q U A L I T Y The quality assurance system in place at Magnetrol® guarantees the highest level of quality throughout the company. MAGNETROL is committed to providing full customer satisfaction both in quality products and quality service. The MAGNETROL quality assurance system is registered to ISO 9001 affirming its commitment to known international quality standards providing the strongest assurance of product/service quality available. Several Electronic MODULEVEL Displacer Transmitters are available for quick shipment, usually within one week after factory receipt of a complete purchase order, through the Expedite Ship Plan (ESP). To take advantage of ESP, simply match the color coded model number codes (standard dimensions apply). E S P Expedite Ship Plan Models covered by ESP service are color coded in the selection data charts. ESP service may not apply to orders of ten units or more. Contact your local representative for lead times on larger volume orders, as well as other products and options. W A R R A N T Y All MAGNETROL electronic level and flow controls are warranted free of defects in materials or workmanship for one full year from the date of original factory shipment. If returned within the warranty period; and, upon factory inspection of the control, the cause of the claim is determined to be covered under the warranty; then, MAGNETROL will repair or replace the control at no cost to the purchaser (or owner) other than transportation. MAGNETROL shall not be liable for misapplication, labor claims, direct or consequential damage or expense arising from the installation or use of equipment. There are no other warranties expressed or implied, except special written warranties covering some MAGNETROL products. For additional information, see Instruction Manual 48-635 or 48-640. 5300 Belmont Road • Downers Grove, Illinois 60515-4499 • 630-969-4000 • Fax 630-969-9489 • www.magnetrol.com 145 Jardin Drive, Units 1 & 2 • Concord, Ontario Canada L4K 1X7 • 905-738-9600 • Fax 905-738-1306 Heikensstraat 6 • B 9240 Zele, Belgium • 052 45.11.11 • Fax 052 45.09.93 Regent Business Ctr., Jubilee Rd. • Burgess Hill, Sussex RH15 9TL U.K. • 01444-871313 • Fax 01444-871317 Copyright © 2012 Magnetrol International, Incorporated. All rights reserved. Printed in the USA. Performance specifications are effective with date of issue and are subject to change without notice. Magnetrol, Magnetrol logotype and Modulevel are registered trademarks of Magnetrol International, Incorporated. BULLETIN: 48-135.4 EFFECTIVE: March 2012 SUPERSEDES: July 2011