Surface Mount Polymer-Tantalum Capacitor NTPL Series FEATURES • Values from 4.7μF to 150μF • Ultra Low Profile (0.9mm Height) • P & B4 Case Sizes (2.0mm x 1.25mm & 3.5mm x 2.8mm) CHARACTERISTICS Capacitance Range Capacitance Tolerance Rated Voltage Range @ 85°C (Vdc) Operating Temperature Range Dissipation Factor Leakage Current @ +25°C (After 5 Minutes at Rated Voltage) Capacitance Change With Temperature 4.7µF to 150µF ±20% (M) 2.5Vdc ~ 10Vdc -55°C ~ +85°C See Specifications Table -55°C ∆C ±20% ∆C ± 10% of intial measured value Resistance to Soldering Heat LC = Less than 300% of specified max. value (+260°C for 5 Seconds) DF less than 200% of specified max. value Moisture Resistance ∆C -20% ~ +40% Max, LC = <300% of specified max. value (500 hours; 90~95% RH @ +60°C) DF = 150% of specified max. value Load Life at Rated Voltage ∆C ±20% initial measure value, LC = Less than specified max. value (1,000 hours @ 85°C) DF = 150% of specified max. value Base Failure Rate 1%/1000 hours at +85°C and rated voltage * Parts with rated voltage <8V recommended derating is 90% of the rated voltage. For parts with rated voltage >8V recommended derating is 80% of the rated voltage. STANDARD VALUES AND CASE SIZES Rated Voltage @ +85°C Surge Voltage @ +85°C Capacitance (µF) Code 4.7 475 10 106 22 226 47 476 68 686 100 107 150 157 2.5 2.9 Case Size P P - 4.0 4.6 Case Size P - 6.3 7.2 Case Size P P P B4 10 12 Case Size P - PART NUMBER SYSTEM NTPL 476 M 6.3 P (150) F Series RoHS Compliant ESR Code Case Size Code Voltage Code Tolerance Code (M = ± 20%) Capacitance Code (1st two digits signficant, 3rd is multiplier) PRECAUTIONS Please review the notes on correct use, safety and precautions found on pages T10 & T11 of NIC’s Electrolytic Capacitor catalog. Also found at www.niccomp.com/precautions If in doubt or uncertainty, please review your specific application - process details with NIC’s technical support personnel: [email protected] 1 NIC COMPONENTS CORP. www.niccomp.com www.lowESR.com www.RFpassives.com SPECIFICATIONS ARE SUBJECT TO CHANGE www.SMTmagnetics.com Surface Mount Polymer-Tantalum Capacitor NTPL Series STANDARD PART NUMBERS AND SPECIFICATIONS NIC Part Number Rated Dissipation Factor ESR (mΩ) Voltage @ +20°C/120Hz @+20°C/100KHz (Vdc) +85°C Capacitance Value (μF) Ripple Current Rating (mA) @ +45°C 100KHz ~ 500KHz Max. LC (mA) after 5 min. 47 0.10 150 23.5 2.5 100 0.10 150 50.0 68 4.0 0.10 150 54.4 10 0.10 250 6.3 22 0.10 150 27.7 6.3 47 0.10 150 59.2 150 0.10 100 94.5 4.7 10 0.10 300 4.7 *Due to character limitation voltage code is "6" instead of "6.3" for the NTPL157M6B4(100)F part. 510 510 510 400 510 510 670 360 NTPL476M2.5P(150)F NTPL107M2.5P(150)F NTPL686M4P(150)F NTPL106M6.3P(250)F NTPL226M6.3P(150)F NTPL476M6.3P(150)F NTPL157M6B4(100)F* NTPL475M10P(300)F Part Marking P Case Size CASE DIMENSIONS (mm) Case Size L H P B4 2.0 ± 0.1 3.5 ± 0.2 0.9 ± 0.1 0.9 ± 0.1 W1 1.25 ± 0.1 2.80 ± 0.2 W2 T 0.9 ± 0.1 2.2 ± 0.1 0.5 ± 0.1 0.8 ± 0.2 Capacitance Code Anode (+) Identifier e H T T L W2 Rated Voltage Code Lot Code Part Marking B4 Case Size W1 Capacitance Code Anode (+) Identifier e 2.5V g 4.0V j 6.3V CAPACITANCE CODES s 4.7mF A7 10mF J7 22mF A 10V A ±0.1 1.65 3.20 B ±0.1 2.40 3.80 C ±0.3 8.0 8.0 j L Rated Voltage Code S7 47mF W7 68mF A8 100mF D ±0.1 3.5 3.5 E ±0.1 1.75 1.75 F ±0.1 4.0 4.0 G ±0.1 2.0 2.0 J H ±0.1 4.0 4.0 J +0.1 φ1.5 φ1.5 K ±0.2 1.3 1.4 t ±0.1 0.25 0.25 Reel Qty 180mm Reel 3,000 3,000 G H B C D E t Lot Code E8 150mF TAPE SPECIFICATIONS (mm) Case Size P B4 A8 + VOLTAGE CODES g J K 2 NIC COMPONENTS CORP. www.niccomp.com A F www.lowESR.com www.RFpassives.com SPECIFICATIONS ARE SUBJECT TO CHANGE www.SMTmagnetics.com Surface Mount Polymer-Tantalum Capacitor NTPL Series REEL SPECIFICATIONS (mm) Tape Width 8mm W2 A +0.0/-3.0 B ± 2.0 C ± 0.2 W1 ± 0.5 W2 ± 1.0 φ180 φ60 φ13 9.0 11.4 C A B B W1 MAXIMUM OF 2 REFLOW PASSES UNDER BELOW CONDITIONS 250°C REFLOW TEMPERATURES/DURATIONS Peak Temperature 250°C 5 seconds 220 200 Cool Down 150 Pre-heat 150°C ~ 180°C 120 sec. max. 100 25 0 Ramp-up 25°C ~ 150°C 60 sec. max. Peak Temperature 260°C 5 seconds 260 Temperature - Deg. C 250 Temperature - Deg. C 260°C REFLOW TEMPERATURES/DURATIONS FOR NTPL475M10P(300)F & NTPL157M6B4(100)F ONLY Time above 220°C 40 sec. max. 180°C ~ 220°C 30 sec. max. 217 200 Pre-heat 150°C ~ 200°C 180 sec. max. 100 25 0 Time Cool Down 150 Time above 217°C 90 sec. max. Ramp-up 25°C ~ 150°C 60 sec. max. 200°C ~ 217°C 6 sec. max. Time RECOMMENDED LAND PATTERN (mm) Case Size P B4 S max. 0.6 1.4 X min. 1.0 1.6 Y min. 0.9 2.7 Y X S X 1. NTPL series maximum storage period is 18 months. The NTPL parts are moisture sensitive (MSL 3) and are shipped in moisture control bags. After opening the bag capacitors should be stored <30˚C, relative humidity of <60% maximum and soldered within 168 hours. 250°C & 260°C PEAK REFLOW TEMPERATURE Case Size Time Conditions MSL All Sizes 168 hours <30°C/60% RH 3 2. The parts should be soldered using the minimum amount of heat required. 3 NIC COMPONENTS CORP. www.niccomp.com www.lowESR.com www.RFpassives.com SPECIFICATIONS ARE SUBJECT TO CHANGE www.SMTmagnetics.com