Surface Mount Polymer-Tantalum Capacitor NTPS Series FEATURES • Low ESR and Very High Capacitance • Values from 47μF to 1,500μF • B (3.5mm x 2.8mm) and D (7.3mm x 4.3mm) Case Size CHARACTERISTICS Capacitance Range Capacitance Tolerance Rated Voltage Range @ 105°C (Vdc) 47µF to 1,500µF ±20% (M) 2.0Vdc ~ 10Vdc -55°C ~ +105°C (Some parts require voltage derating for operation above +85°C. See part number tables for details) Operating Temperature Range Dissipation Factor Leakage Current @ +25°C (After 5 Minutes at Rated Voltage) See Specifications Table Z-55°C/Z+20°C within 0.6 ~ 2.0 Z+105°C/Z+20°C within 0.6 ~ 2.0 ∆C ±10% of initial measured value, LC = Less than 300% spec. max. value DF = Less than 200% of specified max. value ∆C -20% ~ +50% Max, LC = <300% of specified max. value DF = 150% of specified max. value Impedance Ratio Resistance to Soldering Heat (+260°C for 5 Seconds) Moisture Resistance (500 hours; 90~95% RH @ +60°C) Load Life at Rated Voltage 2,000 hours @ 105°C (except B) B & +85°C parts 1,000 hours @ +105°C ∆C ±20% Max, LC = Less than initial specification DF = 150% of specified max. value B case size: 1%/1000 hours at +105°C and rated voltage Other sizes: 0.5%/1000 hours at +105°C and rated voltage B case size: 1%/1000 hours at +85°C and rated voltage Other sizes: 0.5%/1000 hours at +85°C and rated voltage Base Failure Rate * Recommended voltage derating is 90% of rated voltage for < 8V parts and 80% derating for 10V parts. STANDARD VALUES AND CASE SIZES Rated Voltage Surge Voltage Capacitance (µF) Code 47 476 68 686 100 107 120 127 150 157 220 227 330 337 470 477 680 687 1000 108 1500 158 2.0 2.3 Case Size B B - 2.5 2.9 Case Size B, D2 B, D2 D2 D D9 D9 4.0 4.6 Case Size B B, D2 B, D2 D2 D - 6.3 7.2 Case Size B, D2 B B, D2 B, D2 D2, D, D9 D1, D9 D9 - 8.0 9.2 Case Size B - 10 12 Case Size B D2 D D9 - PART NUMBER SYSTEM NTPS 227 M 6.3 D2 (25) F Series RoHS Compliant ESR Code (See specifications tables) Case Size Code Voltage Code Tolerance Code (M = ± 20%) Capacitance Code (1st two digits signficant, 3rd is multiplier) PRECAUTIONS Please review the notes on correct use, safety and precautions found on pages T10 & T11 of NIC’s Electrolytic Capacitor catalog. Also found at www.niccomp.com/precautions If in doubt or uncertainty, please review your specific application - process details with NIC’s technical support personnel: [email protected] 1 NIC COMPONENTS CORP. www.niccomp.com www.lowESR.com www.RFpassives.com SPECIFICATIONS ARE SUBJECT TO CHANGE www.SMTmagnetics.com Surface Mount Polymer-Tantalum Capacitor NTPS Series -55°C ~ +85°C (+105°C with derating) STANDARD VALUES AND SPECIFICATIONS Dissipation Rated Voltage LC (mA) Ripple Current Rated Voltage Factor ESR (mΩ) Derated for after Rating, (mA) @ +45°C (Vdc) @ @+20°C/100KHz Operation >+85°C * 5 minutes 100KHz ~ 500KHz <+85°C* +20°C/120Hz (Vdc) NTPS337M2B(13)F 330 2.0 1.8 132 0.08 13/300KHz 2000 NTPS477M2B(11)F 470 2.0 1.8 188 0.10 11/300KHz 2300 NTPS227M2.5B(25)F 220 2.5 2.0 55 0.08 25 1600 NTPS337M2.5B(35)F 330 2.5 2.0 82.5 0.08 35 1400 NTPS157M4B(35)F 150 4.0 3.2 60 0.08 35 1400 NTPS227M4B(35)F 220 4.0 3.2 88 0.08 35 1400 NTPS107M6.3B(35)F 100 6.3 5.0 63 0.08 35 1400 NTPS127M6.3B(35)F 120 6.3 5.0 75.6 0.08 35 1400 NTPS157M6.3B(25)F 150 6.3 5.0 94.5 0.08 25 1600 NTPS157M6.3B(35)F 150 6.3 5.0 94.5 0.08 35 1400 NTPS227M6.3B(35)F 220 6.3 5.0 138.6 0.10 35 1400 NTPS337M6.3D2(25)F 330 6.3 5.0 207.9 0.10 25 2400 NTPS337M6.3D(9)F 330 6.3 5.0 207.9 0.10 9/500KHz 3900 NTPS337M6.3D9(10)F 330 6.3 5.0 207.9 0.10 10 4400 NTPS477M6.3D1(35)F 470 6.3 5.0 296.1 0.10 35 1700 NTPS107M8B(35)F 100 8.0 6.3 80 0.08 35 1400 NTPS476M10B(35)F 47 10 8.0 47 0.08 35 1400 * Recommended voltage derating is 90% of rated voltage for < 8V parts and 80% derating for 10V parts. NIC Part Number Capacitance Value (μF) -55°C ~ +105°C STANDARD VALUES AND SPECIFICATIONS NIC Part Number Capacitance Rated Voltage Value (μF) (Vdc) +105°C* LC (mA) after 5 minutes Dissipation Factor ESR (mΩ) @ +20°C/120Hz @+20°C/100KHz NTPS337M2B(15)F 330 2.0 132 0.08 15 NTPS227M2.5B(21)F 220 2.5 55 0.08 21 NTPS227M2.5B(35)F 220 2.5 55 0.08 35 NTPS227M2.5B(15)F 220 2.5 110 0.08 15/300kHz NTPS227M2.5D2(25)F 220 2.5 55 0.10 25 NTPS227M2.5D2(9)F 220 2.5 55 0.10 9 NTPS227M2.5D2(15)F 220 2.5 55 0.10 15 NTPS227M2.5D2(18)F 220 2.5 55 0.10 18 NTPS337M2.5D2(25)F 330 2.5 82.5 0.10 25 NTPS337M2.5D2(9)F 330 2.5 82.5 0.10 9 NTPS337M2.5D2(7)F 330 2.5 82.5 0.10 7 NTPS337M2.5D2(18)F 330 2.5 82.5 0.10 18 NTPS337M2.5D2(12)F 330 2.5 82.5 0.10 12 NTPS337M2.5D2(15)F 330 2.5 82.5 0.10 15 NTPS477M2.5D2(18)F 470 2.5 117.5 0.10 18 NTPS477M2.5D2(9)F 470 2.5 117.5 0.10 9 NTPS477M2.5D2(15)F 470 2.5 117.5 0.10 15 NTPS477M2.5D2(12)F 470 2.5 117.5 0.10 12 NTPS477M2.5D2(7)F 470 2.5 117.5 0.10 7 NTPS687M2.5D(15)F 680 2.5 170 0.10 15 NTPS687M2.5D(12)F 680 2.5 170 0.10 12 NTPS108M2.5D9(15)F 1000 2.5 250 0.15 15 NTPS158M2.5D9(15)F 1500 2.5 375 0.15 15 NTPS158M2.5D9(12)F 1500 2.5 375 0.15 12 NTPS107M4B(35)F 100 4.0 40 0.08 35 NTPS157M4D2(18)F 150 4.0 60 0.10 18 * Recommended voltage derating is 90% of rated voltage for < 8V parts and 80% derating for 10V parts. Ripple Current Rating, (mA) @ +45°C 100KHz ~ 500KHz 2000 1700 1400 1800 2400 3900 3100 2800 2400 3900 4400 2800 3500 3100 2800 3900 3100 3500 4400 3100 3500 3900 3900 4400 1400 2800 CONTINUE ON NEXT PAGE 2 NIC COMPONENTS CORP. www.niccomp.com www.lowESR.com www.RFpassives.com SPECIFICATIONS ARE SUBJECT TO CHANGE www.SMTmagnetics.com Surface Mount Polymer-Tantalum Capacitor NTPS Series -55°C ~ +105°C STANDARD VALUES AND SPECIFICATIONS NIC Part Number Capacitance Rated Voltage Value (μF) (Vdc) +105°C* LC (mA) after 5 minutes Dissipation Factor ESR (mΩ) @ +20°C/120Hz @+20°C/100KHz NTPS227M4D2(25)F 220 4.0 88 0.10 25 NTPS227M4D2(18)F 220 4.0 88 0.10 18 NTPS227M4D2(15)F 220 4.0 88 0.10 15 NTPS337M4D2(25)F 330 4.0 132 0.10 25 NTPS337M4D2(18)F 330 4.0 132 0.10 18 NTPS477M4D(18)F 470 4.0 188 0.10 18 NTPS477M4D(10)F 470 4.0 188 0.10 10 NTPS477M4D(12)F 470 4.0 188 0.10 12 NTPS477M4D(15)F 470 4.0 188 0.10 15 NTPS477M4D(25)F 470 4.0 188 0.10 25 NTPS107M6.3B(25)F 100 6.3 63 0.08 25 NTPS107M6.3D2(25)F 100 6.3 63 0.10 25 NTPS107M6.3D2(18)F 100 6.3 63 0.10 18 NTPS157M6.3D2(25)F 150 6.3 94.5 0.10 25 NTPS157M6.3D2(18)F 150 6.3 94.5 0.10 18 NTPS157M6.3D2(15)F 150 6.3 94.5 0.10 15 NTPS227M6.3D2(25)F 220 6.3 138.6 0.10 25 NTPS227M6.3D2(18)F 220 6.3 138.6 0.10 18 NTPS337M6.3D(25)F 330 6.3 207.9 0.10 25 NTPS337M6.3D(18)F 330 6.3 207.9 0.10 18 NTPS337M6.3D(15)F 330 6.3 207.9 0.10 15 NTPS477M6.3D9(25)F 470 6.3 296.1 0.15 25 NTPS477M6.3D9(18)F 470 6.3 296.1 0.15 18 NTPS687M6.3D9(25)F 680 6.3 428.4 0.15 25 NTPS687M6.3D9(18)F 680 6.3 428.4 0.15 18 NTPS686M10D2(25)F 68 10 68 0.10 25 NTPS227M10D(25)F 220 10 220 0.10 25 NTPS227M10D(18)F 220 10 220 0.10 18 NTPS337M10D9(25)F 330 10 330 0.10 25 * Recommended voltage derating is 90% of rated voltage for < 8V parts and 80% derating for 10V parts. Ripple Current Rating, (mA) @ +45°C 100KHz ~ 500KHz 2400 2800 3100 2400 2800 2800 4400 3500 3100 2400 1600 2400 2800 2400 2800 3100 2400 2800 2400 2800 3100 3000 3500 3000 3500 2400 2400 2800 3000 CASE DIMENSIONS (mm) Case Size L H B D1 D2 D D9 3.5 ± 0.2 7.3 ± 0.3 7.3 ± 0.3 7.3 ± 0.3 7.3 ± 0.3 1.9 ± 0.1 1.4 ± 0.1 1.9 +0.1/-0.2 2.8 ± 0.2 3.8 ± 0.2 W1 W2 2.8 ± 0.2 4.3 ± 0.2 4.3 ± 0.2 4.3 ± 0.2 4.3 ± 0.2 T 2.2 ± 0.1 2.4 ± 0.1 2.4 ± 0.1 2.4 ± 0.1 2.4 ± 0.1 0.8 ± 0.2 1.1 ± 0.2 1.3 ± 0.2 1.3 ± 0.2 1.3 ± 0.2 L W1 H W2 T 3 NIC COMPONENTS CORP. www.niccomp.com T www.lowESR.com www.RFpassives.com SPECIFICATIONS ARE SUBJECT TO CHANGE www.SMTmagnetics.com Surface Mount Polymer-Tantalum Capacitor g 4.0V j 6.3V k 8.0V A 10V B CASE SIZE CAPACITANCE CODES A8 100 C8 120 E8 150 J8 220 N8 330 S8 470 B Anode (+) Identifier D1, D2, D & D9 Anode (+) Identifier N8 d + S7 47 E + Rated Voltage Code Lot Code Capacitance CARRIER DIMENSIONS AND REEL QUANTITIES A ±0.1 3.3 4.7 4.5 4.5 4.5 B ±0.1 3.8 7.8 7.5 7.7 7.7 C ±0.3 8.0 12.0 12.0 12.0 12.0 D ±0.1 3.5 5.5 5.5 5.5 5.5 E ±0.1 1.75 1.75 1.75 1.75 1.75 F ±0.1 4.0 8.0 8.0 8.0 8.0 G ±0.1 2.0 2.0 2.0 2.0 2.0 H ±0.1 4.0 4.0 4.0 4.0 4.0 J K ±0.2 2.1 1.7 2.4 3.2 4.2 t max. 0.35 0.40 0.40 0.40 0.40 Reel Quanty 180mm Reel 330mm Reel 2,000 n/a n/a 4,000 n/a 3,000 n/a 2,500 n/a 2,000 G H B C D E t J +0/-0.1 φ1.5 φ1.5 φ1.5 φ1.5 φ1.5 Lot Code Voltage Code Capacitance Code Case Size B D1 D2 D D9 15 e 2.5V j d 2.0V 220 RATED VOLTAGE CODES NTPS Series A K F REEL SPECIFICATIONS (mm) Tape Width 8mm 12mm W2 A B ± 2.0 C ± 0.2 W1 ± 0.5 W2 ± 1.0 φ180 +0/-3.0 φ330 ±2.0 φ60 φ80 φ13 φ13 9.0 13.5 11.4 17.5 C A B B W1 4 NIC COMPONENTS CORP. www.niccomp.com www.lowESR.com www.RFpassives.com SPECIFICATIONS ARE SUBJECT TO CHANGE www.SMTmagnetics.com Surface Mount Polymer-Tantalum Capacitor NTPS Series MAXIMUM OF TWO REFLOW PASSES Temperature - Deg. C 250°C REFLOW TEMPERATURES/DURATIONS Peak Temperature 250°C 5 seconds 250 220 200 Cool Down 150 Pre-heat 150°C ~ 180°C 120 sec. max. 100 25 0 180°C ~ 220°C 30 sec. max. Ramp-up 25°C ~ 150°C 60 sec. max. Time 260°C REFLOW TEMPERATURES/DURATIONS Temperature - Deg. C Time above 220°C 40 sec. max. RECOMMENDED LAND PATTERN (mm) Peak Temperature 260°C 5 seconds 250 Case Size B D1, D2, D, D9 S max. 1.4 3.7 X min. 1.6 2.4 Y min. 2.7 2.9 217 200 Cool Down 150 100 25 0 Time above 217°C 90 sec. max. Pre-heat 150°C ~ 200°C 180 sec. max. Y 200°C ~ 217°C 6 sec. max. Ramp-up 25°C ~ 150°C 60 sec. max. X S X Time 1. NTPS parts are moisture sensitive and are shipped in moisture control bags. After opening the bag capacitors should be stored at <30˚C, relative humidity of <60% maximum and soldered within the timeframe shown in the tables below. 250°C Peak Reflow Temperature Case Size B D1, D2, D, D9 Time 168 hours 4 weeks Conditions <30°C/60% RH <30°C/60% RH MSL 3 2a 260°C Peak Reflow Temperature Case Size All Sizes Time 168 hours Conditions <30°C/60% RH MSL 3 2. The parts should be soldered using the minimum amount of heat required. 5 NIC COMPONENTS CORP. www.niccomp.com www.lowESR.com www.RFpassives.com SPECIFICATIONS ARE SUBJECT TO CHANGE www.SMTmagnetics.com