Surface Mount Polymer-Tantalum Capacitor NTPG Series FEATURES • Values from 33μF to 220μF • Low Profile (1.1mm ~ 1.4mm) • B Case Size (3.5mm x 2.8mm) CHARACTERISTICS Capacitance Range Capacitance Tolerance Rated Voltage Range @ 85°C (Vdc) Operating Temperature Range Dissipation Factor Leakage Current @ +25°C (After 5 Minutes at Rated Voltage) Capacitance Change With Temperature 33µF to 220µF ±20% (M) 2.5Vdc ~ 12.5Vdc -55°C ~ +105°C (voltage derating above +85°C, see specifications table) See Specifications Table -55°C ∆C ±20% ∆C ± 10% of intial measured value Resistance to Soldering Heat LC = Less than 300% of specified max. value (+260°C for 5 Seconds) DF less than 200% of specified max. value Moisture Resistance ∆C -20% ~ +40% Max, LC = <300% of specified max. value (500 hours; 90~95% RH @ +60°C) DF = 150% of specified max. value Load Life at Rated Voltage ∆C ±20% initial measure value, LC = Less than specified max. value (1,000 hours @ 85°C) DF = 150% of specified max. value Base Failure Rate 1%/1000 hours at +85°C and rated voltage * Parts with rated voltage <8V recommended derating is 90% of the rated voltage. For parts with rated voltage >8V recommended derating is 80% of the rated voltage. STANDARD VALUES AND CASE SIZES Rated Voltage @ +85°C 2.5 Surge Voltage @ +85°C 2.9 Derated Voltage @ 105°C 2.0 Capacitance (µF) Code Case Size 33 336 47 476 100 107 150 157 220 227 B3, B2 4.0 4.6 3.2 Case Size B3 6.3 7.2 5.0 Case Size B2 B3 - 8 10 12.5 9.2 12 14 6.3 8 10 Case Size Case Size Case Size B2 B2 B2 - PART NUMBER SYSTEM NTPG 157 M 6.3 B3 (35) F Series RoHS Compliant ESR Code Case Size Code Voltage Code Tolerance Code (M = ± 20%) Capacitance Code (1st two digits signficant, 3rd is multiplier) PRECAUTIONS Please review the notes on correct use, safety and precautions found on pages T10 & T11 of NIC’s Electrolytic Capacitor catalog. Also found at www.niccomp.com/precautions If in doubt or uncertainty, please review your specific application - process details with NIC’s technical support personnel: [email protected] 1 NIC COMPONENTS CORP. www.niccomp.com www.lowESR.com www.RFpassives.com SPECIFICATIONS ARE SUBJECT TO CHANGE www.SMTmagnetics.com Surface Mount Polymer-Tantalum Capacitor NTPG Series STANDARD PART NUMBERS AND SPECIFICATIONS NIC Part Number Capacitance Value (μF) NTPG227M2.5B2(70)F NTPG227M2.5B3(30)F NTPG227M4B3(70)F NTPG107M6.3B2(70)F NTPG107M6.3B2(55)F NTPG157M6.3B3(70)F NTPG157M6.3B3(35)F NTPG476M8B2(70)F NTPG476M10B2(70F NTPG336M12B2(70)F 220 220 220 100 100 150 150 47 47 33 Rated Voltage Rated Max. LC Derated for Dissipation Factor ESR (mΩ) Voltage (mA) Operation >+85°C @ +20°C/120Hz @+20°C/100KHz (Vdc) +85°C after 5 min. (Vdc) 0.10 70 55 2.5 2.0 0.10 30/300KHz 110 4.0 3.2 0.10 70 88 0.10 70 63 0.10 55 63 6.3 5.0 0.10 70 94.5 0.10 35/300KHz 189 8.0 6.3 0.10 70 37.6 10 8.0 0.10 70 47 12.5 10 0.10 70 41.3 Ripple Current Rating (mA) @ +45°C 100KHz ~ 500KHz 1,000 1,400 1,000 1,000 1,100 1,000 1,200 1,000 1,000 1,000 CASE DIMENSIONS (mm) Case Size B2 B3 L H W1 W2 T 3.5 +0.3/-0.1 1.1 ± 0.1 2.8 +0.3/-0.1 2.2 ± 0.1 3.5 +0.3/-0.1 1.4 ± 0.1 2.8 +0.3/-0.1 2.2 ± 0.1 L 0.8 ± 0.2 0.8 ± 0.2 W1 H W2 T VOLTAGE CODES e 2.5V g 4.0V j 6.3V CAPACITANCE CODES N7 33mF S7 47mF A8 100mF k 8.0V A 10V E8 150mF J8 220mF Black Body Anode (+) Identifier B 12.5V A8 + T j L Rated Voltage Code Lot Code Capacitance Code TAPE SPECIFICATIONS (mm) Case Size B3, B2 A ±0.1 3.25 B ±0.1 3.90 C ±0.3 8.0 D ±0.1 3.5 E ±0.1 1.75 F ±0.1 4.0 J H ±0.1 4.0 J +0.1 φ1.5 K ±0.2 1.7 t ±0.1 0.25 Reel Qty 180mm Reel 2,500 G H B C D E t G ±0.1 2.0 K 2 NIC COMPONENTS CORP. www.niccomp.com A F www.lowESR.com www.RFpassives.com SPECIFICATIONS ARE SUBJECT TO CHANGE www.SMTmagnetics.com Surface Mount Polymer-Tantalum Capacitor NTPG Series REEL SPECIFICATIONS (mm) Tape Width 8mm W2 A +0.0/-3.0 B ± 2.0 C ± 0.2 W1 ± 0.5 W2 ± 1.0 φ180 φ60 φ13 9.0 11.4 C A B B W1 MAXIMUM OF 2 REFLOW PASSES UNDER BELOW CONDITIONS 260°C REFLOW TEMPERATURES/DURATIONS Peak Temperature 250°C 5 seconds 250 Temperature - Deg. C Temperature - Deg. C 250°C REFLOW TEMPERATURES/DURATIONS 220 200 Cool Down 150 Pre-heat 150°C ~ 180°C 120 sec. max. 100 25 0 Ramp-up 25°C ~ 150°C 60 sec. max. Time above 220°C 40 sec. max. 180°C ~ 220°C 30 sec. max. Peak Temperature 260°C 5 seconds 260 217 200 Cool Down 150 Pre-heat 150°C ~ 200°C 180 sec. max. 100 25 Ramp-up 25°C ~ 150°C 60 sec. max. 0 Time Time above 217°C 90 sec. max. 200°C ~ 217°C 6 sec. max. Time RECOMMENDED LAND PATTERN (mm) Case Size B3, B2 S max. 1.4 X min. 1.6 Y min. 2.7 Y X S X 1. NTPG parts are moisture sensitive (MSL 3) and are shipped in moisture control bags. After opening the bag capacitors should be stored <30˚C, relative humidity of <60% maximum and soldered within 168 hours. 250°C & 260°C PEAK REFLOW TEMPERATURE Case Size Time Conditions MSL All Sizes 168 hours <30°C/60% RH 3 2. The parts should be soldered using the minimum amount of heat required. 3 NIC COMPONENTS CORP. www.niccomp.com www.lowESR.com www.RFpassives.com SPECIFICATIONS ARE SUBJECT TO CHANGE www.SMTmagnetics.com