Surface Mount Polymer-Tantalum Capacitor FEATURES • Ultra Low ESR and High Ripple Current Ratings • High Capacitance (up to 680μF) • Low Profile (2.8mm height) • D Case Size (7.3mm x 4.3mm) CHARACTERISTICS Capacitance Range Capacitance Tolerance Rated Voltage Range @ 105°C (Vdc) Operating Temperature Range Dissipation Factor Leakage Current @ +25°C (After 5 Minutes at Rated Voltage) Capacitance Change With Temperature Resistance to Soldering Heat (+260°C for 5 Seconds) Moisture Resistance (500 hours; 90~95% RH @ +60°C) Load Life at Rated Voltage (2,000 hours @ 105°C) Base Failure Rate NTPF Series 150µF to 680µF ±20% (M) 4.0Vdc ~ 10Vdc -55°C ~ +105°C See Specifications Table -55°C ∆C ±20% ∆C ±10% of initial measured value, LC = Less than 300% of specified max. value, DF = Less than 200% of specified max. value ∆C -20% ~ +40% Max, LC = <300% of specified max. value DF = 150% of specified max. value ∆C ±20% Max, LC = Less than specified max. value DF = 150% of specified max. value 0.5%/1000 hours at +105°C and rated voltage * Parts with rated voltage >10V recommended derating is 80% of the rated voltage. For parts with rated voltage <10V recommended derating is 90% of the rated voltage. STANDARD VALUES AND CASE SIZES Rated Voltage @ +105°C 4.0 Surge Voltage @ +105°C 4.6 Capacitance (µF) Code Case Size 150 157 220 227 330 337 D 470 477 D 680 687 D9 6.3 7.2 Case Size D D D9 - 10 12 Case Size D - PART NUMBER SYSTEM NTPF 227 M 6.3 D (9) F Series RoHS Compliant (9) ESR in milli-ohms Case Size Code Voltage Code Tolerance Code (M = ± 20%) Capacitance Code (1st two digits signficant, 3rd is multiplier) PRECAUTIONS Please review the notes on correct use, safety and precautions found on pages T10 & T11 of NIC’s Electrolytic Capacitor catalog. Also found at www.niccomp.com/precautions If in doubt or uncertainty, please review your specific application - process details with NIC’s technical support personnel: [email protected] 1 NIC COMPONENTS CORP. www.niccomp.com www.lowESR.com www.RFpassives.com SPECIFICATIONS ARE SUBJECT TO CHANGE www.SMTmagnetics.com Surface Mount Polymer-Tantalum Capacitor NTPF Series STANDARD PART NUMBERS AND SPECIFICATIONS NIC Part Number Capacitance Value (μF) NTPF337M4D(12)F NTPF477M4D(10)F NTPF687M4D9(10)F NTPF227M6.3D(12)F NTPF227M6.3D(9)F NTPF337M6.3D(9)F NTPF477M6.3D9(10)F NTPF157M10D(15)F Leakage Dissipation Factor ESR (mΩ) Current (mA) @ +20°C/120Hz @+20°C/100KHz after 5 minutes Rated Voltage (Vdc) +105°C 330 470 680 220 220 330 470 150 132.0 188.0 272.0 138.6 138.6 207.9 296.1 150.0 4.0 6.3 10 0.10 0.10 0.10 0.10 0.10 0.10 0.10 0.10 Ripple Current Rating (mA) @ +45°C 100KHz ~ 500KHz 12 10 10 12 9 9 10 15 4000 4400 4400 4000 4600 3900 4400 3600 CASE DIMENSIONS (mm) Case Size L H D D9 7.3 ± 0.3 7.3 ± 0.3 2.8 ± 0.2 3.8 ± 0.2 W1 W2 4.3 ± 0.2 4.3 ± 0.2 T 2.4 ± 0.1 2.4 ± 0.1 L 1.3 ± 0.2 1.3 ± 0.2 W1 H W2 T j 6.3V A 10V Capacitance A ±0.1 4.5 4.5 B ±0.1 7.7 7.7 C ±0.3 12.0 12.0 D ±0.1 5.5 5.5 E ±0.1 1.75 1.75 F ±0.1 8.0 8.0 H ±0.1 4.0 4.0 J J -0/+0.1 φ1.5 φ1.5 K ±0.2 3.2 4.2 t ±0.1 0.30 0.30 Reel Qty 330mm Reel 2,500 2,000 G H B C D E t G ±0.1 2.0 2.0 Lot Code Voltage Code CARRIER DIMENSIONS AND REEL QUANTITIES Case Size D D9 Series Code j 15 F g 4.0V Black Body Anode (+) Identifier + VOLTAGE CODES 220 T K 2 NIC COMPONENTS CORP. www.niccomp.com A www.lowESR.com F www.RFpassives.com SPECIFICATIONS ARE SUBJECT TO CHANGE www.SMTmagnetics.com Surface Mount Polymer-Tantalum Capacitor NTPF Series REEL SPECIFICATIONS (mm) Tape Width 12mm W2 A ±2.0 B ± 2.0 C ± 0.2 W1 ± 0.5 W2 ± 1.0 φ330 φ80 φ13 13.5 17.5 C A B B W1 MAXIMUM OF 2 REFLOW PASSES UNDER BELOW CONDITIONS Peak Temperature 250°C 5 seconds 250 220 200 Cool Down 150 Pre-heat 150°C ~ 180°C 120 sec. max. 100 25 0 Ramp-up 25°C ~ 150°C 60 sec. max. Time above 220°C 40 sec. max. 180°C ~ 220°C 30 sec. max. 260°C REFLOW TEMPERATURES/DURATIONS (Exception: NTPF157M10D(15F) is 250°C only) Temperature - Deg. C Temperature - Deg. C 250°C REFLOW TEMPERATURES/DURATIONS Peak Temperature 260°C 5 seconds 260 217 200 Cool Down 150 Pre-heat 150°C ~ 200°C 180 sec. max. 100 25 0 Time Time above 217°C 90 sec. max. 200°C ~ 217°C 6 sec. max. Ramp-up 25°C ~ 150°C 60 sec. max. Time RECOMMENDED LAND PATTERN (mm) Case Size D, D9 S max. 3.7 X min. 2.4 Y min. 2.9 Y X S X 1. NTPF parts are moisture sensitive and are shipped in moisture control bags. After opening the bag capacitors should be stored at <30˚C, relative humidity of <60% maximum and soldered within timeframe shown in the tables below. 2. The parts should be soldered using the minimum amount of heat required. 3 250°C PEAK REFLOW TEMPERATURE Case Size Time Conditions All Sizes 4 weeks <30°C/60% RH MSL 2a 260°C PEAK REFLOW TEMPERATURE Case Size Time Conditions All Sizes 168 hours <30°C/60% RH MSL 3 NIC COMPONENTS CORP. www.niccomp.com www.lowESR.com www.RFpassives.com SPECIFICATIONS ARE SUBJECT TO CHANGE www.SMTmagnetics.com