Surface Mount Polymer-Tantalum Capacitor FEATURES • Low ESR and High Voltage • Values from 2.7μF to 150μF • Voltage Ratings to 35V • B (3.5mm x 2.8mm) & D Case Size (7.3mm x 4.3mm) CHARACTERISTICS Capacitance Range Capacitance Tolerance Rated Voltage Range @ 105°C (Vdc) Operating Temperature Range Dissipation Factor Leakage Current @ +25°C (After 5 Minutes at Rated Voltage) NTPH Series 2.7µF to 150µF ±20% (M) 16Vdc ~ 35Vdc* -55°C ~ +105°C See Specifications Table Impedance Ratio +105°C Z+105°C/Z+20°C within 0.6 ~ 1.0 ∆C ± 10% of initial measured value, LC = Less than 300% of specified max. value DF = Less than 200% of specified max. value ∆C -20% ~ +40% of initial measured value, LC = <300% of specified max. value DF = 150% of specified max. value ∆C ±20% of initial value, LC = Less than specified max. value DF = 150% of specified max. value 0.5%/1000 hours at +105°C and rated voltage Z-55°C/Z+20°C within 1.0 ~ 2.0 Resistance to Soldering Heat (+250°C for 10 Seconds) Moisture Resistance (500 hours; 90~95% RH @ +60°C) Load Life at Rated Voltage (2,000 hours @ 105°C) Base Failure Rate * Recommended derating is 90% of the rated voltage. STANDARD VALUES AND CASE SIZES Rated Voltage @ +105°C 16 20 Surge Voltage @ +15°C ~+35°C 20 23 Capacitance (µF) Code Case Size Case Size 2.7 275 3.9 395 5.6 565 8.2 825 B 10 106 B 15 156 B 22 226 B, V 33 336 D5, V V 47 476 D1, V D1, V 68 686 V 100 107 V D 150 157 D - 25 29 Case Size B B, V D1, V V - 35 40 Case Size B3 B V - PART NUMBER SYSTEM NTPH 336 M 16 D5 (40) F Series RoHS Compliant ESR Code Case Size Code Voltage Code Tolerance Code (M = ± 20%) Capacitance Code (1st two digits signficant, 3rd is multiplier) PRECAUTIONS Please review the notes on correct use, safety and precautions found on pages T10 & T11 of NIC’s Electrolytic Capacitor catalog. Also found at www.niccomp.com/precautions If in doubt or uncertainty, please review your specific application - process details with NIC’s technical support personnel: [email protected] 1 NIC COMPONENTS CORP. www.niccomp.com www.lowESR.com www.RFpassives.com SPECIFICATIONS ARE SUBJECT TO CHANGE www.SMTmagnetics.com Surface Mount Polymer-Tantalum Capacitor NTPH Series STANDARD PART NUMBERS AND SPECIFICATIONS NIC Part Number Leakage Current (mA) after 5 minutes Capacitance Rated Voltage Value (μF) (Vdc) +105°C NTPH106M16B(100)F NTPH156M16B(90)F NTPH336M16D5(40)F NTPH336M16V(70)F NTPH476M16D1(55)F NTPH476M16V(55)F NTPH476M16V(40)F NTPH686M16V(50)F NTPH107M16V(50)F NTPH157M16D(50)F NTPH825M20B(100)F NTPH226M20B(90)F NTPH226M20V(80)F NTPH336M20V(60)F NTPH476M20D1(55)F NTPH476M20V(55)F NTPH107M20D(55)F NTPH565M25B(100)F NTPH156M25B(100)F NTPH156M25V(90)F NTPH156M25V(45)F NTPH226M25D1(70)F NTPH226M25V(60)F NTPH226M25V(45)F NTPH336M25V(60)F NTPH275M35B3(300)F NTPH395M35B(400)F NTPH106M35V(120)F 10 15 33 33 47 47 47 68 100 150 8.2 22 22 33 47 47 100 5.6 15 15 15 22 22 22 33 2.7 3.9 10 Dissipation Factor ESR (mΩ) @ +20°C/120Hz @+20°C/100KHz 48.0 72.0 52.8 52.8 75.2 75.2 75.2 108.8 160.0 240.0 49.2 132.0 44.0 66.0 94.0 94.0 200.0 42.0 112.5 38.0 38.0 55.0 55.0 55.0 82.5 47.3 40.9 35.0 16 20 25 35 0.10 0.10 0.10 0.10 0.10 0.10 0.10 0.10 0.10 0.10 0.10 0.10 0.10 0.10 0.10 0.10 0.10 0.10 0.10 0.10 0.10 0.10 0.10 0.10 0.10 0.10 0.10 0.10 100 90 40 70 55 55 40 50 50 50 100 90 80 60 55 55 55 100 100 90 45 70 60 45 60 300 400 120 Ripple Current Rating (mA) @ +105°C 100KHz ~ 500KHz 800 1,000 1,800 1,400 1,500 1,450 1,800 1,500 1,800 1,800 800 1,000 1,300 1,400 1,500 1,450 1,700 800 900 1,000 100KHz < 300KHz 1,500 100KHz < 300KHz 1,400 1,400 1,500 100KHz < 300KHz 1,400 800 500 1,000 CASE DIMENSIONS (mm) Case Size L H B3 B D1 D D5 V 3.5 ± 0.2 3.5 ± 0.2 7.3 ± 0.2 7.3 ± 0.3 7.3 ± 0.2 7.3 ± 0.2 1.4 ± 0.1 1.9 ± 0.1 1.4 ± 0.1 2.8 ± 0.2 1.15 ± 0.05 1.9 ± 0.1 W1 W2 2.8 ± 0.2 2.8 ± 0.2 4.3 ± 0.2 4.3 ± 0.2 4.3 ± 0.2 4.3 ± 0.2 L 2.2 ± 0.1 2.2 ± 0.1 2.4 ± 0.1 2.4 ± 0.1 2.4 ± 0.1 2.4 ± 0.1 T 0.8 ± 0.2 0.8 ± 0.2 1.3 ± 0.2 1.3 ± 0.2 1.3 ± 0.2 1.3 ± 0.2 W1 H W2 T 2 T NIC COMPONENTS CORP. www.niccomp.com www.lowESR.com www.RFpassives.com SPECIFICATIONS ARE SUBJECT TO CHANGE www.SMTmagnetics.com Surface Mount Polymer-Tantalum Capacitor VOLTAGE CODES C 16V D 20V 1E* 25V NTPH Series V 35V Letter "E" for B3 and B case sizes B3 and B CASE SIZE CAPACITANCE CODES Code Cap. (mF) L6 2.7 Q6 3.9 U6 5.6 Y6 8.2 A7 10 E7 15 J7 22 B3 & B Anode (+) Identifier Q6 + V c Rated Voltage Code Lot Code Capacitance Code NTPH156M25V(45)F & NTPH226M25V(45)F D1, D, D5 & V Anode (+) Identifier 22 1E 34 + Rated Voltage Code 22 + Anode (+) Identifier 1E L Rated Voltage Code Lot Code Capacitance (mF) Special Performance Code V Lot Code Capacitance (mF) CARRIER DIMENSIONS AND REEL QUANTITIES Case Size B3 B D1 D D5 V A ±0.1 3.3 3.3 4.5 4.5 4.5 4.5 B ±0.1 3.8 3.8 7.5 7.7 7.5 7.5 C ±0.3 8.0 8.0 12.0 12.0 12.0 12.0 D ±0.1 3.5 3.5 5.5 5.5 5.5 5.5 E ±0.1 1.75 1.75 1.75 1.75 1.75 1.75 F ±0.1 4.0 4.0 8.0 8.0 8.0 8.0 H ±0.1 4.0 4.0 4.0 4.0 4.0 4.0 J J -0.0/+0.1 f1.5 f1.5 f1.5 f1.5 φ1.5 φ1.5 K ±0.2 2.1 2.1 2.4 3.2 1.7 2.4 t ±0.1 0.20 0.25 0.30 0.30 0.30 0.30 Reel Quantity 180mm Reel 336Mm Reel 2,000 n/a 2,000 n/a n/a 3,000 n/a 2,500 n/a 4,500 n/a 3,000 G H B C D E t G ±0.1 2.0 2.0 2.0 2.0 2.0 2.0 K 3 NIC COMPONENTS CORP. www.niccomp.com A www.lowESR.com F www.RFpassives.com SPECIFICATIONS ARE SUBJECT TO CHANGE www.SMTmagnetics.com Surface Mount Polymer-Tantalum Capacitor NTPH Series REEL SPECIFICATIONS (mm) Tape Width 8mm 12mm W2 A B ± 2.0 C ± 0.2 W1 ± 0.5 W2 ± 1.0 φ180 -0/+3 φ330 ±2.0 φ60 φ80 φ13 φ13 9.0 13.5 11.4 17.5 C A B B W1 MAXIMUM OF 2 REFLOW PASSES UNDER BELOW CONDITIONS Temperature - Deg. C 250°C REFLOW TEMPERATURES/DURATIONS Peak Temperature 250°C 10 seconds 250 217 200 Cool Down 150 Pre-heat 150°C ~ 180°C 120 sec. max. 100 25 0 Time above 217°C 60 sec. max. Time above 200°C 70 sec. max. Ramp-up 25°C ~ 150°C 60 sec. max. Time RECOMMENDED LAND PATTERN (mm) Case Size B3, B D1, D, D5, V S max. 1.4 3.7 X min. 1.6 2.4 Y min. 2.7 2.9 Y X S X 1. NTPH parts are moisture sensitive (MSL 3) and are shipped in moisture control bags. After opening the bag capacitors should be stored at <30˚C, relative humidity of <60% maximum and soldered within 168 hours. 250°C PEAK REFLOW TEMPERATURE Case Size Time Conditions All Sizes 168 hours <30°C/60% RH MSL 3 2. The parts should be soldered using the minimum amount of heat required. 4 NIC COMPONENTS CORP. www.niccomp.com www.lowESR.com www.RFpassives.com SPECIFICATIONS ARE SUBJECT TO CHANGE www.SMTmagnetics.com