Product Discontinued (see discontinuation notice at: http://www.niccomp.com/pcn/pdf/EOL-NSPE-U-12052012.pdf) Hybrid Aluminum Electrolytic Capacitors NSPE-U Series • CYLINDRICAL V-CHIP CONSTRUCTION FOR SURFACE MOUNTING • HIGH TEMPERATURE RANGE (+125°C) • ULTRA LOW ESR AND HIGH RIPPLE CURRENT • 8x10.8 ~ 10x10.8mm CASE SIZES • REFLOW SOLDERING RATED TO +260°C (see reflow specifications) RoHS • MEETS THE REQUIREMENTS OF AEC-Q200* Compliant *Contact NIC for supporting test data includes all homogeneous materials CHARACTERISTICS Rated Voltage Range Rated Capacitance Range Operating Temp. Range Capacitance Tolerance Max. Leakage Current After 2 Minutes @ 20°C *See Part Number System for Details 6.3 ~ 16Vdc 22 ~ 560μF -55 ~ +125°C ±20% (M) See Specifications Tables W.V. (Vdc) S.V. (Vdc) Working and Surge Voltage Ratings 6.3 8.2 0.18 Tan δ @ 120Hz/20°C Z -55°C/Z +20°C Z +125°C/Z +20°C W.V. (Vdc) Case Dia. φ8 & 10mm Capacitance Change Tan δ and ESR Leakage Current ESR Impedance Ratio Load Life Test @ 125°C and Rated Voltage 10 16 13 20 0.16 0.14 1 ~ 2.5 0.5 ~ 1.0 6.3 10 16 2000 hrs. Within ±30% of initial measured value Less than 200% of specified max. value Less than specified max. value Less than 200% of specified max. value STANDARD PRODUCTS AND CASE SIZES Dφ x L (mm) 8X10.8 0.18 492 Max. ESR (mΩ) AT 100KHz/20°C 17 10X10.8 0.18 593 16 2190 2000 560 10X10.8 0.18 706 16 2190 2000 NSPE-U101M10V8X10.8LBF 100 8X10.8 0.16 200 20 1680 2000 NSPE-U221M10V8X10.8LBF 220 8X10.8 0.16 440 18 1680 2000 NSPE-U391M10V10X10.8LBF 390 10X10.8 0.16 780 17 2060 2000 NSPE-U220M16V8X10.8LBF 22 8X10.8 0.14 100 28 1380 2000 NSPE-U330M16V8X10.8LBF 33 8X10.8 0.14 106 26 1380 2000 NSPE-U470M16V8X10.8LBF 47 8X10.8 0.14 151 24 1380 2000 NSPE-U680M16V8X10.8LBF 68 8X10.8 0.14 218 22 1380 2000 NSPE-U101M16V10X10.8LBF 100 10X10.8 0.14 320 19 1850 2000 Cap. Working Case Size Max. Tan δ Max. LC (μA) (μF) Voltage (D X L) mm 120Hz/20°C After 2 min.* PART NUMBER NSPE-U391M6.3V8X10.8LBF 390 NSPE-U471M6.3V10X10.8LBF 470 NSPE-U561M6.3V10X10.8LBF 6.3 10 16 For Automotive Applications See Part Numbering System 100Hz 0.05 1KHz 0.20 10KHz 0.50 Load Life Hours (+125°C) 2000 *Please review typical leakage current performance, as shown on NIC load life endurance test report. PART NUMBER SYSTEM RIPPLE CURRENT FREQUENCY CORRECTION FACTORS Cap. μF C < 10 Max. Ripple Current (mA rms) AT 100KHz/125°C 1780 100KHz 1.00 NSPE-U 391 M 6.3V 8x10.8 L B Y F Series RoHS Compliant Sn-Bi Finish, 13" Reel Reflow Temp. Code (N=+260°C) Size in mm Working Voltage Tolerance Code M=20% Capacitance Code in μF, first 2 digits are significant Third digit is no. of zeros, “R” indicates decimal for values under 10μF Optional: Suitable for automotive equipment, sourced to special production and inspection at TS-16949 certified production site PRECAUTIONS Please review the notes on correct use, safety and precautions found on pages T10 & T11 of NIC’s Electrolytic Capacitor catalog. Also found at www.niccomp.com/precautions If in doubt or uncertainty, please review your specific application - process details with NIC’s technical support personnel: [email protected] NIC COMPONENTS CORP. www.niccomp.com www.lowESR.com www.RFpassives.com SPECIFICATIONS ARE SUBJECT TO CHANGE www.SMTmagnetics.com 1 Hybrid Aluminum Electrolytic Capacitors NSPE-U Series Part Marking DIMENSIONS (mm) Case Size 8x10.8 10x10.8 Dφ ±0.5 8.0 10 L max. 10.8 10.8 A, B ±0.2 8.3 10.3 W 0.7 ~ 1.0 1.0 ~ 1.4 + Dφ I ±0.2 2.9 3.2 I P ±0.2 3.2 4.6 Series Code Lot Code - I u__ 220 10V W A L 0.3mm max. Capacitance Value P Voltage B Temperature - Deg. C RECOMMENDED REFLOW SOLDERING PROFILE LAND PATTERN DIM. (mm) Peak Temperature (see table below) 250 230 200 Case Dia. 8 10 Time Above 230°C (40 seconds max.) 150 Time Above 200°C (see table below) 100 A 4.1 4.4 B 2.1 2.5 + Preheat - 120 seconds max. (see table for temperature) P 2.8 4.3 - 50 B Time (Seconds) PEAK TEMPERATURE AND DURATION Preheat Time above Time above Peak Number (120 sec. max.) 200°C 230°C Temperature of Reflow Passes 150°C ~ 190°C 90 sec. max. 40 sec. max. 250°C/5 sec. 2x* 6.3 ~ 10mm 150°C ~ 180°C 60 sec. max. 40 sec. max. 260°C/5 sec. 1x *Two reflow passes are permissible with a cool down to room temperature required between the first and second pass. Diameter A P A TAPING SPECIFICATIONS (mm) 1. Both Leader and Trailer tape: Minimum 40mm (1.57") empty carrier tape pockets. 2. Leader tape: Approximately 20cm of cover tape at leader. 4 + 0.1 3. Connection: Maximum 3 connections (slices) per reel. C ±0.3 24.0 24.0 D ±0.1 11.5 11.5 P ±0.1 16.0 16.0 T ±0.2 11.0 11.0 t max. 0.6 0.6 - D B ±0.5 8.7 10.7 t B 8x10.8 10x10.8 A ±0.5 8.7 10.7 1.75 ± C Case Size 1.75 + 0.15 1.5∅ +0.1/1.5φ+0.1/-0 + A T Qty per Reel 13" (330mm) 300 300 φ13mm ± 0.5mm φ50mm min. 8x10.8 10x10.8 W ±1.0 26 26 Feeding 2mm ± 0.5mm REEL DIMENSIONS (mm) Case Size P φ21mm ± 0.8mm φ330mm ± 2.0mm or φ380mm ± 2.0mm 2 NIC COMPONENTS CORP. www.niccomp.com www.lowESR.com W www.RFpassives.com SPECIFICATIONS ARE SUBJECT TO CHANGE 3mm www.SMTmagnetics.com