70 Maxess Road ? Melville, New York 11747

6/4/99
70 Maxess Road ! Melville, New York 11747
(631) 396-7500 ! Fax (631) 396-7575
PART MARKING GUIDE
PRODUCTS: SMT THICK FILM CHIP RESISTORS AND ARRAYS
SERIES: NRC AND NRSN
Please be advised NIC Component NRC series of thick film chip resistors are marked with three digit
(for E-24 5% tolerance values) or four digits (for E-96 1% tolerance values) resistance value marking
codes. This marking is in compliance with EIA-575, the standard for chip resistors. Section 1.2.3
"Resistance", of the EIA standard, details the coding of the 3 and 4 digit marking codes. Table III
shows designation 3-digit and 4-digit codes covering resistance values from 0.1ohm to 10 Meg-ohm.
Table IV identifies the industry standard 1% (F) and 5% (J) tolerance values. Unfortunately Table IV
contains several typographical errors, so please refer to the attached NIC Standard Resistance Values
table for correct resistance values.
COMPONENT MARKING:
Please note the following marking systems are used on all 0603 (5% tolerance) and larger sizes (1%
and 5% tolerance) chip resistor products.
Marking is white lettering on black.
E24 Values ( ±5% tolerance)
471
3 digit (±5% tolerance part)
470Ω example shown
3-digit codes (5% tolerances) breakdown as follows:
• First and Second digits identify the resistance value.
• The Third digit indicates the number of zeros.
• "R" is used as decimal point on values below 10 ohms.
Examples: 1.5 ohm = "1R5", 33 ohm = "330", 470 ohm = "471" code, 1200 ohm = "122" code, 10,000
ohm = "103", 560,000 ohm = "564" and 1,000,000 ohm = "105"
“332” = 3300Ω
Ω
“220” = 22Ω
Ω
“220” = 22Ω
Ω
8 TERMINAL
4 ELEMENT
RESISTOR ARRAY
“102” = 1000Ω
Ω
10 TERMINAL
8 ELEMENT
RESISTOR ARRAY
ISO 9002 REGISTERED
6/4/99
70 Maxess Road ! Melville, New York 11747
(631) 396-7500 ! Fax (631) 396-7575
Part Marking continued…
E96 Values ( ±1% tolerance)
4 digit (±1% tolerance part)
107,000Ω example shown.
1073
4-digit codes (1% tolerances) breakdown as follows:
• First, Second and Third digits identify the resistance value.
• The Fourth digit indicates the number of zeros.
• "R" is used as decimal point on values below 100 ohms.
Examples: 1.15 ohm = "1R15", 33.2 ohm = "33R2", 475 ohm = "4750" code, 1270 ohm = "1271" code,
10,500 ohm = "1052", 562,000 ohm = "5623" and 1,000,000 ohm = "1004"
“1003” = 100,000Ω
Ω
Special Cases: Non-standard value ±1% (F) tolerance chip resistors.
Please be advise ±1% (F) tolerance chip resistors supplied in the following non-standard E96 values
will be marked with 3-digit codes:
1. E24 (±5% tolerance) values:
120,160,180,220,240,270,300,330,360,390,430,470,510,560,620,680,820 and 910.
Ωand below 10Ω
Ω.
2. Values above 1 MegΩ
For example:
• P/N: NRC10F1005TR (10 MegΩ±1%) is a special value and is supplied marked with 3-digit code; “106”.
•
P/N: NRC12F4702TR (47KΩ±1%) is a standard E24 value in special ±1% (F) tolerance and is
supplied marked with 3-digit code; “473”.
0603 SIZE E96 (±1% TOLERANCE):
Due to limited space special 3-digit codes, per JIS-C-5201 (see example below), are used for 0603 size
(±1% tolerance) parts.
"07" is code for "115" value
1
"B" is code for 10 multiplier
Ω
"07B" is marking code for 1150Ω
10C
"10" is JIS C 5201 code for "124" value
2
"C" is JIS C 5201 code for 10 multiplier
Ω
"10C" is marking code for 12,400Ω
0402 SIZE PARTS: 0402 size parts are too small to resistance value mark
ISO 9002 REGISTERED
6/4/99
70 Maxess Road ! Melville, New York 11747
(631) 396-7500 ! Fax (631) 396-7575
Part Marking continued…
Standard Resistance Values
(PER EIA-575 & RS 460)
E12
E24
10
12
15
18
22
27
33
39
47
56
68
82
91
10
11
12
13
15
16
18
20
22
24
27
30
33
36
39
43
47
51
56
62
68
75
82
91
E96
10.0
10.2
10.5
10.7
11.0
11.3
11.5
11.8
12.1
12.4
12.7
13.0
13.3
13.7
14.0
14.3
14.7
15.0
15.4
15.8
16.2
16.5
16.9
17.4
17.8
18.2
18.7
19.1
19.6
20.0
20.5
21.0
21.5
22.1
22.6
23.2
23.7
2.43
24.9
25.5
26.1
26.7
27.4
28.0
28.7
29.4
30.1
30.9
31.6
32.4
33.2
34.0
34.8
35.7
36.5
37.4
38.3
39.2
40.2
41.2
42.2
43.2
44.2
45.3
ISO 9002 REGISTERED
46.4
47.5
48.7
49.9
51.1
52.3
53.6
54.9
56.2
57.6
59.0
60.4
61.9
63.4
64.9
66.5
68.1
69.8
71.5
73.2
75.0
76.8
78.7
80.6
82.5
84.5
86.6
88.7
90.9
93.1
95.3
97.6