HA13165H Multiple Voltage Regulator for Car Audio REJ03F0223-0100 Rev.1.00 Jan 16, 2007 Description The HA13165H is a compact multiple voltage regulator for car audio system. This IC has seven output system, these are 5.7 V output for a microcontroller, 7 V output for CD driver, 8.5 V output for audio control, 10 V output for illuminations, 5.0 V output for independent from microcontroller line, and high side switch for remote-ANT and remote-external AMP. Functions General • ACC power monitor circuit is built-in as to detect low voltage. • Low saturation output (PNP output) used for audio output. • Adjustable voltage for illumination output by changing an external resistor. Protections • Output current limit circuit to avoid device destruction caused by shorted output, etc. • High surge input protector against VCC and ACC. • Built in a thermal shutdown circuit to prevent against the thermal destruction. Rev.1.00 Jan 16, 2007 page 1 of 9 HA13165H Pin Description and Equivalent Circuit Function Pin No. Pin Name Specification 1 — NC 2 ANT OUT VCC-1 V/500 mA min Equivalent Circuit Vcc Vcc Normal Operation TSD 24 V Surge Input — — — — Output voltage is VCC-1 V when M or H level to CTRL pin and H level to ANTCTRL. 0V 0V 0V Connected to ACC. — — — 5.7 V 5.7 V 0V Output voltage is 5 V when M or H level applied to CTRL pin. 0V 0V 0V Output for ACC detector 0V 5V (ACC Hi) 0V L: ANT output OFF H: ANT output ON — — — Connected to VCC — — — 90 kΩ 10 kΩ 3 ACC IN — 45 kΩ 15 kΩ 4 VDD OUT 5.7 V/100 mA min Regular 5.7 V. Vcc Vcc 175 kΩ 50 kΩ 5 SW5V OUT 5.0 V/100 mA min VDD Vcc 6 COMP OUT 5.0 V/100 mA min 50 kΩ 7 ANT CTRL — 51 kΩ 49 kΩ 8 VCC — Rev.1.00 Jan 16, 2007 page 2 of 9 HA13165H Pin Description and Equivalent Circuit (cont.) Function Pin No. 9 Pin Name BATT DET Specification Equivalent Circuit — 10 AUDIO OUT 8.5 V/500 mA min Surge Input TSD 24 V Detect Detect Not detect Output voltage is 8.5 V when M or H level applied to CTRL pin. 0V 0V 0V L: BIAS OFF M: BIAS ON H: CD ON — — — Output voltage is 7 V when H level applied to CTRL pin. 0V 0V 0V Adjustment pin for ILM output voltage. — — — Output voltage is 10 V when M or H level applied to CTRL pin 0V 0V 0V Connected to GND — — — Low battery detect. VDD 250 kΩ Normal Operation 10 kΩ Vcc Vcc 77.3 kΩ 12.3 kΩ 11 CTRL — 65 kΩ 35 kΩ 12 CD OUT 7.0 V/1.3 A min Vcc Vcc 64.7 kΩ 12.4 kΩ 13 ILM AJ — 14 ILM OUT 10.0 V/500 mA min Vcc Vcc 33.4 kΩ 5 kΩ 15 GND — Rev.1.00 Jan 16, 2007 page 3 of 9 HA13165H Timing Chart VCC 8.5 V 9.25 V VDD OUT CTRL ANT CTRL AUDIO OUT CD OUT ILM OUT SW5V OUT ANT OUT ACC IN 2.8 V COMP OUT B.DET current Rev.1.00 Jan 16, 2007 page 4 of 9 2.5 V HA13165H Block Diagram VCC ANT OUT 8 3 ACC IN + − Surge protector 2 0.1 µF +B ACC 9 BATT.DET + − 1 BIAS ANT CTRL CTRL CD OUT TSD 6 + − 7 4 + 10 µF VDD OUT 11 0.1 µF + − 12 0.1 µF AUDIO OUT COMP OUT 5 − + − + 10 14 ILM OUT 0.1 µF 15 GND Rev.1.00 Jan 16, 2007 page 5 of 9 SW5V OUT TAB GND 13 ILM AJ HA13165H Absolute Maximum Ratings (Ta = 25°C) Item Operating power supply voltage Symbol Rating 18 Unit V Note Vcc DC supply voltage Peak voltage Vcc(DC) Vcc(PEAK) 24 50 V V 1 2 Power dissipation Junction temperature Pd Tj 36 150 W °C 3 Operating temperature Storage temperature Topr Tstg –40 to +85 –55 to +125 °C °C Notes: Recommended power supply voltage range 10 to 16 V. 1. Applied time is less than 60 s. 2. Surge pulse as input. 3. Ta = 25°C. : Permissible power dissipation when using a heat sink of infinite area. Refer to the derating curves below. Power dissipation Pd (W) 20 15 thin = 1.6 mm, 100 cm Aluminum heat sink 11.0 W thin = 1.6 mm, 50 cm Aluminum heat sink 10 8.7 W 5 w/o heat sink 1.8 W 0 0 25 50 75 100 125 Ambient temperature Ta (°C) Rev.1.00 Jan 16, 2007 page 6 of 9 150 175 HA13165H Electrical Characteristics (unless otherwise noted, Vcc = 13.2 V, Ta = 25°C) Item Standby current CTRL L level (STBY mode) Symbol IST VCL Min — 0 Typ 460 — Max 700 1.0 Unit µA V CTRL M level (CD OFF mode) CTRL H level (CD ON mode) VCM VCH 2.0 4.0 — — 3.0 – V V ANT CTRL L level (ANT OFF mode) ANT CTRL H level (ANT ON mode) VACL VACH 0 3.0 — — 2.0 – V V VDD OUT Output voltage Voltage regulation Vo1 ∆Vo11 5.45 — 5.7 10 5.95 50 V mV Io1 = 80 mA Vcc = 10 to 16 V, Io1 = 80 mA Load regulation Minimum I/O voltage differential ∆Vo12 ∆Vo13 — — 50 1.0 100 1.5 mV V Io1 = 0 to 80 mA Io1 = 80 mA Output current capacity Ripple rejection ratio Io1 SVR1 100 50 250 60 — — mA dB Vo1 ≥ 5.45 V f = 100 Hz, Io1 = 80 mA Output voltage Voltage regulation Vo2 ∆Vo21 6.7 — 7.0 40 7.3 100 V mV Io2 = 1.0 A Vcc = 10 to 16V, Io2 = 1.0 A Load regulation Minimum I/O voltage differential ∆Vo22 ∆Vo23 — — 70 1.0 150 1.5 mV V Io2 = 10m to 1.0 A Io2 = 1.0 A Output current capacity Ripple rejection ratio Io2 SVR2 1.3 45 2.0 50 — — A dB Vo2 ≥ 6.7 V f = 100 Hz, Io2 = 1.0 A Output voltage Voltage regulation Vo3 ∆Vo31 8.0 — 8.5 30 9.0 90 V mV Io3 = 400 mA Vcc = 10 to 16 V, Io3 = 400 mA Load regulation Minimum I/O voltage differential ∆Vo32 ∆Vo33 — — 100 0.4 200 0.9 mV V Io3 = 10 to 400 mA Io3 = 400 mA Output current capacity Ripple rejection ratio Io3 SVR3 500 40 850 50 — — mA dB Vo3 ≥ 8.0 V f = 100 Hz, Io3 = 400 mA Output voltage Voltage regulation Vo4 ∆Vo41 9.35 — 9.85 40 10.35 100 V mV Io4 = 400 mA Vcc = 12.5 to 16 V, Io4 = 400 mA Load regulation Minimum I/O voltage differential ∆Vo42 ∆Vo43 — — 50 1.0 100 1.5 mV V Io4 = 10 to 400 mA Io4 = 400 mA Output current capacity Ripple rejection ratio Io4 SVR4 500 32 900 40 — — mA dB Vo4 ≥ 9.35 V f = 100 Hz, Io4 = 400 mA Differential I/O voltage Load regulation ∆Vo51 ∆Vo52 — — 1.0 350 1.5 600 V mV Io5 = 500 mA Io5 = 10 to 500 mA Output current capacity Output voltage Io5 Vo6 500 4.6 900 5.0 — 5.4 mA V Vo5 ≥ 11.7 V Io6 = 80 mA, VDD = no load Output current capacity Output voltage Io6 Vo7 100 4.6 300 5.0 — 5.4 mA V Vo6 ≥ 4.6 V Io7 = 40 mA, VDD = no load Output current capacity Rise threshold voltage Io7 VTHH7 100 2.6 300 2.8 — 3.0 mA V Vo7 ≥ 4.6 V Hysteresis range Threshold voltage ∆VTH7 VTHH8 0.2 8.3 0.3 8.6 0.4 8.9 V V Hysteresis range Output current capacity ∆VTH8 Io8 0.55 200 0.75 — 0.95 — V µA CD OUT AUDIO OUT ILM OUT ANT OUT SW5V OUT ACC OUT BATT. DET Rev.1.00 Jan 16, 2007 page 7 of 9 Test Condition ACC = 0 V, CTRL = 0 V Vo = 0.3 V HA13165H Evaluation Circuit HA13165H NC 1 ANT OUT 2 ACC IN 3 C2 VDD OUT 4 SW5V COMP ANT OUT OUT CTRL 5 6 7 VCC 8 BATT AUDIO DET OUT CTRL 9 10 11 C3 0.1 µF ANT C8 + 0.1 µF VDD SW5V COMP CD OUT 12 ILM AJ 13 C9 10 µF BATT.DET AUDIO ILM OUT 14 GND 15 C10 0.1 µF CD 0.1 µF ILM SW1 SW4 100 µF ACC Rev.1.00 Jan 16, 2007 page 8 of 9 C6 C7 + ANT CTRL VCC SW2 SW3 R2 3.3 kΩ R3 3.3 kΩ 0.1 µF CTRL 5V HA13165H Package Dimensions JEITA Package Code P-HSIP15-14.3x19.66-1.27 RENESAS Code PRSS0015DA-C Previous Code SP-15TGV MASS[Typ.] 3.0g Unit : mm 20.5 MAX 19.66 19.0 3.3MiN ±0.3 2-C3.0 ±0.2 3.5 TYP 3.8MAX 1.1MiN 1.28 TYP 1.50MAX ±0.2 17.9 7.8 13.8 11.3 ±0.3 3.0 ±0.2 φ 3.6 1.11±0.25 0.6 ±0.1 1.27 ±0.25 2.54 *1 ±0.25 0.25 *1 +0.10 -0.05 1.8 ±0.25 3.5 ±0.5 6.04 *1 ±0.5 *1 Note) 1. Dimension "*1" is the value after bending. ( Ni/Pd/Au plating ) Rev.1.00 Jan 16, 2007 page 9 of 9 Sales Strategic Planning Div. Nippon Bldg., 2-6-2, Ohte-machi, Chiyoda-ku, Tokyo 100-0004, Japan Notes: 1. This document is provided for reference purposes only so that Renesas customers may select the appropriate Renesas products for their use. Renesas neither makes warranties or representations with respect to the accuracy or completeness of the information contained in this document nor grants any license to any intellectual property rights or any other rights of Renesas or any third party with respect to the information in this document. 2. Renesas shall have no liability for damages or infringement of any intellectual property or other rights arising out of the use of any information in this document, including, but not limited to, product data, diagrams, charts, programs, algorithms, and application circuit examples. 3. You should not use the products or the technology described in this document for the purpose of military applications such as the development of weapons of mass destruction or for the purpose of any other military use. When exporting the products or technology described herein, you should follow the applicable export control laws and regulations, and procedures required by such laws and regulations. 4. All information included in this document such as product data, diagrams, charts, programs, algorithms, and application circuit examples, is current as of the date this document is issued. Such information, however, is subject to change without any prior notice. Before purchasing or using any Renesas products listed in this document, please confirm the latest product information with a Renesas sales office. Also, please pay regular and careful attention to additional and different information to be disclosed by Renesas such as that disclosed through our website. (http://www.renesas.com ) 5. Renesas has used reasonable care in compiling the information included in this document, but Renesas assumes no liability whatsoever for any damages incurred as a result of errors or omissions in the information included in this document. 6. When using or otherwise relying on the information in this document, you should evaluate the information in light of the total system before deciding about the applicability of such information to the intended application. Renesas makes no representations, warranties or guaranties regarding the suitability of its products for any particular application and specifically disclaims any liability arising out of the application and use of the information in this document or Renesas products. 7. With the exception of products specified by Renesas as suitable for automobile applications, Renesas products are not designed, manufactured or tested for applications or otherwise in systems the failure or malfunction of which may cause a direct threat to human life or create a risk of human injury or which require especially high quality and reliability such as safety systems, or equipment or systems for transportation and traffic, healthcare, combustion control, aerospace and aeronautics, nuclear power, or undersea communication transmission. If you are considering the use of our products for such purposes, please contact a Renesas sales office beforehand. Renesas shall have no liability for damages arising out of the uses set forth above. 8. Notwithstanding the preceding paragraph, you should not use Renesas products for the purposes listed below: (1) artificial life support devices or systems (2) surgical implantations (3) healthcare intervention (e.g., excision, administration of medication, etc.) (4) any other purposes that pose a direct threat to human life Renesas shall have no liability for damages arising out of the uses set forth in the above and purchasers who elect to use Renesas products in any of the foregoing applications shall indemnify and hold harmless Renesas Technology Corp., its affiliated companies and their officers, directors, and employees against any and all damages arising out of such applications. 9. You should use the products described herein within the range specified by Renesas, especially with respect to the maximum rating, operating supply voltage range, movement power voltage range, heat radiation characteristics, installation and other product characteristics. Renesas shall have no liability for malfunctions or damages arising out of the use of Renesas products beyond such specified ranges. 10. Although Renesas endeavors to improve the quality and reliability of its products, IC products have specific characteristics such as the occurrence of failure at a certain rate and malfunctions under certain use conditions. Please be sure to implement safety measures to guard against the possibility of physical injury, and injury or damage caused by fire in the event of the failure of a Renesas product, such as safety design for hardware and software including but not limited to redundancy, fire control and malfunction prevention, appropriate treatment for aging degradation or any other applicable measures. Among others, since the evaluation of microcomputer software alone is very difficult, please evaluate the safety of the final products or system manufactured by you. 11. In case Renesas products listed in this document are detached from the products to which the Renesas products are attached or affixed, the risk of accident such as swallowing by infants and small children is very high. You should implement safety measures so that Renesas products may not be easily detached from your products. Renesas shall have no liability for damages arising out of such detachment. 12. This document may not be reproduced or duplicated, in any form, in whole or in part, without prior written approval from Renesas. 13. Please contact a Renesas sales office if you have any questions regarding the information contained in this document, Renesas semiconductor products, or if you have any other inquiries. http://www.renesas.com RENESAS SALES OFFICES Refer to "http://www.renesas.com/en/network" for the latest and detailed information. Renesas Technology America, Inc. 450 Holger Way, San Jose, CA 95134-1368, U.S.A Tel: <1> (408) 382-7500, Fax: <1> (408) 382-7501 Renesas Technology Europe Limited Dukes Meadow, Millboard Road, Bourne End, Buckinghamshire, SL8 5FH, U.K. Tel: <44> (1628) 585-100, Fax: <44> (1628) 585-900 Renesas Technology (Shanghai) Co., Ltd. Unit 204, 205, AZIACenter, No.1233 Lujiazui Ring Rd, Pudong District, Shanghai, China 200120 Tel: <86> (21) 5877-1818, Fax: <86> (21) 6887-7898 Renesas Technology Hong Kong Ltd. 7th Floor, North Tower, World Finance Centre, Harbour City, 1 Canton Road, Tsimshatsui, Kowloon, Hong Kong Tel: <852> 2265-6688, Fax: <852> 2730-6071 Renesas Technology Taiwan Co., Ltd. 10th Floor, No.99, Fushing North Road, Taipei, Taiwan Tel: <886> (2) 2715-2888, Fax: <886> (2) 2713-2999 Renesas Technology Singapore Pte. Ltd. 1 Harbour Front Avenue, #06-10, Keppel Bay Tower, Singapore 098632 Tel: <65> 6213-0200, Fax: <65> 6278-8001 Renesas Technology Korea Co., Ltd. Kukje Center Bldg. 18th Fl., 191, 2-ka, Hangang-ro, Yongsan-ku, Seoul 140-702, Korea Tel: <82> (2) 796-3115, Fax: <82> (2) 796-2145 Renesas Technology Malaysia Sdn. Bhd Unit 906, Block B, Menara Amcorp, Amcorp Trade Centre, No.18, Jalan Persiaran Barat, 46050 Petaling Jaya, Selangor Darul Ehsan, Malaysia Tel: <603> 7955-9390, Fax: <603> 7955-9510 © 2007. Renesas Technology Corp., All rights reserved. Printed in Japan. Colophon .7.0