ALUMINUM ELECTROLYTIC CAPACITORS UT 6mmL Chip Type , Wide Temperature Range series Chip type with load life 2000 hours at +105°C. Designed for surface mounting on high density PC board. Applicable to automatic mounting machine fed with carrier tape. Compliant to the RoHS directive (2002/95/EC). UA Long Life UT Long Life WT UX Higher C/V Specifications Item Performance Characteristics Category Temperature Range – 55 to +105°C Rated Voltage Range 4 to 50V Rated Capacitance Range 0.1 to 100µF Capacitance Tolerance ± 20% at 120Hz, 20°C Leakage Current After 2 minutes' application of rated voltage, leakage current is not more than 0.01 CV or 3 (µA) , whichever is greater. Measurement frequency :120Hz, Temperature : 20°C Tangent of loss angle (tan δ) 4 0.37 Rated voltage (V) tan δ (MAX.) 6.3 0.28 10 0.24 16 0.20 25 0.16 35 0.13 50 0.12 Measurement frequency :120Hz 4 6 12 Rated voltage (V) Z– 25°C / Z+20°C Impedance ratio Z– 40°C / Z+20°C ZT / Z20 (MAX.) Stability at Low Temperature 6.3 3 8 16 2 4 25 2 3 35 2 3 50 2 3 Within ±25% of the initial capacitance value (16V or less) Within ±20% of the initial capacitance value (25V or more) 200% or less than the initial specified value Less than or equal to the initial specified value Capacitance change tan δ Leakage current The specifications listed at right shall be met when the capacitors are restored to 20°C after the rated voltage is applied for 2000 hours at 105°C. Endurance 10 3 5 After storing the capacitors under no load at 105°C for 1000 hours and then performing voltage treatment based on JIS C 5101-4 clause 4.1 at 20°C, they shall meet the specified values for the endurance characteristics listed above. The capacitors are kept on a hot plate for 30 seconds, which is Capacitance change Within ±10% of the initial capacitance value maintained at 250°C. The capacitors shall meet the characteristic Less than or equal to the initial specified value tan δ requirements listed at right when they are removed from the plate Less than or equal to the initial specified value Leakage current and restored to 20°C. Shelf Life Resistance to soldering heat Black print on the case top. Marking Type numbering system (Example : 16V 10µF) Chip Type 1 Positive Plastic platform 0.3MAX. C±0.2 B±0.2 0.5 to 0.8 5.8±0.3 Voltage mark for 6.3V is A±0.2 φD±0.5 X2P 10 16V Voltage E Lot No. A±0.2 Capacitance 2 3 4 5 6 7 8 9 10 11 12 13 14 UU T 1 C 1 0 0 M C L 1 GS 0.5MAX. 105°C Marking φD 4 A B C E 1.8 4.3 4.3 1.0 5 2.1 5.3 5.3 1.3 Taping code (mm) 6.3 2.4 6.6 6.6 2.2 Configuration Capacitance tolerance (±20%) Rated capacitance (10µF) Rated voltage (16V) Series name Negative Type 6V . Dimensions V Cap.(µF) 0.1 0.22 0.33 0.47 1 2.2 3.3 4.7 10 22 33 47 100 4 0G Code 0R1 R22 R33 R47 010 2R2 3R3 4R7 100 220 330 470 101 4 5 5 6.3 6.3 0J 22 30 36 60 4 5 5 6.3 10 1A 22 30 36 60 5 5 6.3 6.3 16 1C 27 35 46 60 4 5 6.3 6.3 25 1E 18 30 40 50 4 5 6.3 6.3 35 1V 13 23 38 48 4 5 6.3 50 1H 15 25 42 4 4 4 4 4 4 4 5 6.3 1.0 2.6 3.2 3.8 6.2 11 14 19 30 Case size φ D (mm) Allowable Rated ripple ripple Rated ripple current (mArms) at 105°C 120Hz Frequency coefficient of rated ripple current Frequency Coefficient 50 Hz 0.70 120 Hz 1.00 300 Hz 1.17 1 kHz 1.36 10 kHz or more 1.50 Taping specifications are given in page 23. Recommended land size, soldering by reflow are given in page 18, 19. Please select UX(p.104), UJ(p.108) series if high C/V products are required. Please refer to page 3 for the minimum order quantity. CAT.8100Z