ALUMINUM ELECTROLYTIC CAPACITORS ZT 4.5mmL Chip Type, Wide Temperature Range series WT Chip type with 4.5mm height, operating over wide temperature range of – 40 to +105°C. Designed for surface mounting on high density PC board. Applicable to automatic mounting machine fed with carrier tape. Compliant to the RoHS directive (2011/65/EU). Smaller ZT Smaller ZG Specifications Item Performance Characteristics Category Temperature Range – 40 to +105°C Rated Voltage Range 6.3 to 50V Rated Capacitance Range 0.1 to 100µF Capacitance Tolerance ± 20% at 120Hz, 20°C Leakage Current After 2 minutes' application of rated voltage, leakage current is not more than 0.01CV or 3 (µA) , whichever is greater. Measurement frequency : 120Hz at 20°C Tangent of loss angle (tan δ) 6.3 0.38 Rated voltage (V) tan δ (MAX.) 10 0.32 16 0.20 25 0.16 35 0.14 50 0.14 Measurement frequency : 120Hz Stability at Low Temperature 6.3 6 10 Rated voltage (V) Z– 25°C / Z+20°C Impedance ratio Z– 40°C / Z+20°C ZT / Z20 (MAX.) 10 5 10 25 3 6 35 3 4 50 3 4 Within ±25% of the initial capacitance value (16V or less) Within ±20% of the initial capacitance value (25V or more) tan δ 300% or less than initial specified value Leakage current Less than or equal to the initial specified value Capacitance change The specifications listed at right shall be met when the capacitors are restored to 20°C after the rated voltage is applied for 1000 hours at 105°C. Endurance 16 3 6 After storing the capacitors under no load at 105°C for 1000 hours and then performing voltage treatment based on JIS C 5101-4 clause 4.1 at 20°C, they shall meet the specified values for the endurance characteristics listed above. The capacitors are kept on a hot plate for 30 seconds, which Capacitance change Within ±10% of the initial capacitance value is maintained at 250°C. The capacitors shall meet the tan δ Less than or equal to the initial specified value characteristic requirements listed at right when they are Leakage current Less than or equal to the initial specified value removed from the plate and restored to 20°C. Shelf Life Resistance to soldering heat Black print on the case top. Marking Chip Type Type numbering system (Example : 16V 10µF) 4.5 0.5 MAX. +0.1 –0.2 Voltage mark for 6.3V is 6V . 2 3 4 5 6 7 8 9 10 11 12 13 14 U Z T 1 C 1 0 0 MC L 1 GB Taping code A±0.3 A + – 0.3 φD±0.5 A2P 10 16V C±0.2 B±0.2 Plastic platform Voltage 0.3 MAX. Lot No. E Capacitance 1 Positive 105°C Marking φD A B C E 4 1.8 4.3 4.3 1.0 (mm) 5 6.3 2.1 2.4 5.3 6.6 5.3 6.6 1.3 2.2 Configuration Capacitance tolerance (±20%) Rated capacitance (10µF) Rated voltage (16V) Series name Negative 0.5 to 0.8 Type Dimensions 6.3 0J V Cap. (µF) 0.1 0.22 0.33 0.47 1 2.2 3.3 4.7 10 22 33 47 100 Code 0R1 R22 R33 R47 010 2R2 3R3 4R7 100 220 330 470 101 4 5 5 6.3 10 1A 19 26 32 52 5 5 6.3 16 1C 24 30 40 4 5 6.3 6.3 25 1E 16 26 35 44 4 5 6.3 6.3 35 1V 11 20 33 42 4 5 6.3 50 1H 13 22 36 4 4 4 4 4 4 4 5 6.3 Case size φ D (mm) 0.9 2.2 2.8 3.3 5.4 9.6 12 16 26 Rated ripple Rated ripple current (mArms) at 105°C 120Hz Frequency coefficient of rated ripple current Frequency Coefficient 50 Hz 0.70 120 Hz 1.00 300 Hz 1.17 1 kHz 1.36 10 kHz or more 1.50 Taping specifications are given in page 23. Recommended land size, soldering by reflow are given in page 18, 19. Please select UX(p.158), UJ(p.164) series if high C/V products are reqired. Please refer to page 3 for the minimum order quantity. CAT.8100C