PDF

ALUMINUM ELECTROLYTIC CAPACITORS
CB
Chip Type, Long Life Assurance
series
Chip type with load life of 7000 hours at +105°C.
Applicable to automatic mounting machine fed with carrier tape.
Compliant to the RoHS directive (2011/65/EU).
CB
UL
Long Life
Low
Impedance
CW
Specifications
Item
Performance Characteristics
Category Temperature Range
–25 to +105°C
Rated Voltage Range
6.3 to 50V
Rated Capacitance Range
0.1 to 1000µF
Capacitance Tolerance
± 20% at 120Hz, 20°C
Leakage Current
After 2 minutes' application of rated voltage, leakage current is not more than 0.03 CV or 4 (µA) , whichever is greater.
Measurement frequency : 120Hz at 20°C
Rated voltage (V)
tan δ (MAX.)
Tangent of loss angle (tan δ)
6.3
0.32
10
0.28
16
0.26
25
0.16
35
0.14
50
0.14
Measurement frequency : 120Hz
Rated voltage (V)
Stability at Low Temperature
Impedance ratio
ZT / Z20 (MAX.)
6.3
10
16
25
35
50
4
3
2
2
2
2
Z– 25°C / Z+20°C
The specifications listed at right shall be met
when the capacitors are restored to 20°C
after the rated voltage is applied for 7000
hours at 105°C.
Endurance
Capacitance change
tan δ
Leakage current
Within ±30% of the initial capacitance value
300% or less than the initial specified value
Less than or equal to the initial specified value
After storing the capacitors under no load at 105°C for 1000 hours and then performing voltage treatment based on JIS C 5101-4
clause 4.1 at 20°C, they shall meet the specified values for the endurance characteristics listed above.
The capacitors are kept on a hot plate for 30 seconds, which is
Capacitance change Within ±10% of the initial capacitance value
maintained at 250°C. The capacitors shall meet the characteristic
Less than or equal to the initial specified value
tan δ
requirements listed at right when they are removed from the plate
Less than or equal to the initial specified value
Leakage current
and restored to 20°C.
Shelf Life
Resistance to soldering
heat
Black print on the case top.
Marking
Chip Type
Type numbering system (Example : 16V 100µF)
(φ4 to φ6.3)
Positive
L±0.3
Capacitance
Lot No.
3
4
5
6
7
8
9 10 11 12 13 14
Taping code
E
B±0.2
φD±0.5
A2
100C
CB
C±0.2
2
A±0.2 A±0.2
0.3MAX.
Series
1
UCB 1 C 1 0 1 MC L 1 GS
0.5MAX.
Plastic platform
Voltage ( C : 16V )
Configuration
Capacitance tolerance (±20%)
Rated capacitance (100µF)
Rated voltage (16V)
Negative
H
φD
4 to 6.3
8 • 10
Code
CL
NL
Series name
Type
Positive
0.3MAX.
C±0.2
E
B±0.2
A2
220V
CB
φD±0.5
Series
L±0.5
Lot No.
Voltage
V
6.3
Code j
Capacitance
10
A
16
C
Pressure relief vent
25
E
35
V
H
(mm)
φD
A±0.2 A±0.2
Plastic platform
0.5MAX.
(φ8 to φ10 )
Voltage ( V : 35V )
Trade mark
Negative
×L
10 × 10
4×7
5×7
6.3 × 7
6.3 × 8.7
8 × 10
A
1.8
2.1
2.4
2.4
2.9
3.2
B
4.3
5.3
6.6
6.6
8.3
10.3
C
4.3
5.3
6.6
6.6
8.3
10.3
E
1.0
1.3
2.2
2.2
3.1
4.5
L
7.0
7.0
7.0
8.7
10
10
H
0.5 to 0.8
0.5 to 0.8
0.5 to 0.8
0.5 to 0.8
0.8 to 1.1
0.8 to 1.1
50
H
Dimension table in next page.
CAT.8100D
ALUMINUM ELECTROLYTIC CAPACITORS
CB
series
Dimensions
Cap.(µF)
V
6.3
10
16
25
35
50
Code
0J
1A
1C
1E
1V
1H
0.1
0R1
4 ×7
1.0
0.22
R22
4 ×7
2.6
0.33
R33
4 ×7
3.2
0.47
R47
4 ×7
3.8
1
010
4 ×7
2.2
2R2
4 ×7
11
3.3
3R3
4 ×7
14
4.7
4R7
4 ×7
15
4 ×7
18
5 ×7
25
5 ×7
30
6.3 ×7
42
57
10
100
22
220
33
330
47
470
5 ×7
36
100
101
6.3 ×7
60
220
221
6.3 ×8.7
101
330
331
160
470
471
1000
102
4 ×7
22
8 ×10
5 ×7
8 ×10
48
6.3 ×8.7
63
50
6.3 ×8.7
6.3 ×8.7
81
116
8 ×10
6.2
8 ×10
77
8 ×10
92
10 ×10
10 ×10
151
216
10 ×10
313
6.3 ×7
6.3 ×7
141
10 ×10
35
254
Case size Rated
φ D × L (mm) ripple
Rated ripple current (mArms) at 105°C 120Hz
Frequency coefficient of rated ripple current
Frequency
Coefficient
50 Hz
0.70
120 Hz
1.00
300 Hz
1.17
1 kHz
1.36
10 kHz or more
1.50
Taping specifications are given in page 23.
Recommended land size, soldering by reflow are given
in page 18, 19.
Please refer to page 3 for the minimum order quantity.
CAT.8100D