ALUMINUM ELECTROLYTIC CAPACITORS LH Chip Type, High Voltage. High Reliability. series Chip type, High voltage and High Reliability. Load life of 4000 hours at +125°C. Applicable to automatic mounting machine using carrier tape. Adapted to the RoHS directive (2011/65/EU). LH Long Life LT Specifications Item Category Temperature Range Rated Voltage Range Rated Capacitance Range Capacitance Tolerance Leakage Current Performance Characteristics –40 to +125°C 160 to 450V 2.2 to 27µF ± 20% at 120Hz, 20°C After 1 minute's application of rated voltage, leakage current is not more than 0.04CV+100 (µA). Measurement frequency : 120Hz at 20°C Rated voltage (V) tan δ (MAX.) Tangent of loss angle (tan δ) 160 0.20 200 0.20 250 0.25 400 0.25 450 0.30 Measurement frequency : 120Hz Rated voltage (V) Impedance ratio Z–40°C / Z+20°C ZT / Z20 (MAX.) Stability at Low Temperature 160 200 250 400 450 6 6 10 10 15 Within ±30% of the initial capacitance value 300% or less than the intial specified value Less than or equal to the initial specified value After storing the capacitors under no load at 125°C for 1000 hours and then performing voltage treatment based on JIS C 5101-4 clause 4.1 at 20°C, they shall meet the specified values for the endurance characteristics listed above. The capacitors are kept on a hot plate for 30 seconds, Within ±10% of the initial capacitance value Capacitance change which is maintained at 250°C and then performing voltage treatment based on JIS C 5101-4 clause 4.1 at 20°C, they Less than or equal to the initial specified value tan δ shall meet the characteristic requirements listed at right Less than or equal to the initial specified value Leakage current when they are removed from the plate. Black print on the case top. Shelf Life Resistance to soldering heat Marking Chip Type Type numbering system (Example : 400V 5.6µF) Plastic platform 0.3MAX. Voltage(2G : 400V) Series C±0.2 2 3 4 5 6 7 8 9 10 11 12 13 14 U L H 2 G 5 R 6 MNL 1 GS A±0.2 Taping code Configuration A±0.2 E B±0.2 φD±0.5 A2 5.6 2G LH Lot No. Capacitance 1 Positive 0.5MAX. (φ8 × 10L, φ10) Trade mark Capacitance change tan δ Leakage current The specifications listed at right shall be met when the capacitors are restored to 20°C after the rated voltage is applied for 4000 hours at 125°C. Endurance L±1.0 Rated capacitance (5.6µF) Negative H Pressure relief vent Capacitance tolerance (±20%) Rated voltage (400V) Series name (mm) φD × L A B C E L H 8 × 10 10 × 10 2.9 3.2 10.3 8.3 10.3 8.3 3.1 4.5 10 10 0.8 to 1.1 0.8 to 1.1 Type 10 × 13.5 3.2 10.3 10.3 4.5 13.5 0.8 to 1.1 Voltage V Code 160 200 250 400 450 2C 2D 2E 2G 2W Dimensions Cap.(µF) 2.2 3.3 3.9 5.6 7.5 10 12 15 18 22 27 160 2C V Code 2R2 3R3 3R9 5R6 7R5 100 120 150 180 220 270 200 2D 8 × 10 45 10 × 10 60 10 × 13.5 65 250 2E 8 × 10 45 10 × 10 60 10 × 13.5 65 400 2G 8 × 10 30 10 × 10 10 × 13.5 45 50 8 × 10 30 10 × 10 10 × 13.5 45 50 8 × 10 450 2W 20 10 × 10 10 × 13.5 35 40 Case size φ D × L (mm) Rated ripple Rated ripple current (mArms) at 125°C 120Hz Frequency coefficient of rated ripple current Frequency Coefficient 50 Hz 0.70 120 Hz 1.00 300 Hz 1.17 1 kHz 1.36 10 kHz or more 1.50 Taping specifications are given in page 23. Recommended land size, soldering by reflow are given in page 18, 19. Please refer to page 3 for the minimum order quantity. CAT.8100D