ALUMINUM ELECTROLYTIC CAPACITORS WP 5.5mmL Chip Type, Bi-Polarized series Designed for surface mounting on high density PC board. Applicable to automatic mounting machine fed with carrier tape. Compliant to the RoHS directive (2011/65/EU). WP Smaller ZP Specifications Item Performance Characteristics Category Temperature Range –40 to +85°C Rated Voltage Range 6.3 to 50V Rated Capacitance Range 0.1 to 100µF Capacitance Tolerance ±20% at 120Hz, 20°C Leakage Current After 2 minutes' application of rated voltage, leakage current is not more than 0.05CV or 10 (µA) ,whichever is greater. Measurement frequency : 120Hz at 20°C 6.3 0.24 Rated voltage (V) tan δ (MAX.) Tangent of loss angle (tan δ) 10 0.20 16 0.17 25 0.17 35 0.15 50 0.15 Measurement frequency : 120Hz 6.3 4 8 Rated voltage (V) Z– 25°C / Z+20°C Impedance ratio Stability at Low Temperature ZT / Z20 (MAX.) Z– 40°C / Z+20°C 10 3 6 The specifications listed at right shall be met when the capacitors are restored to 20°C after the rated voltage is applied for 1000 hours at 85°C with the polarity inverted every 250 hours. Endurance 16 2 4 35 2 3 50 2 3 Within ±20% of the initial capacitance value 200% or less than the initial specified value Less than or equal to the initial specified value Capacitance change tan δ Leakage current After storing the capacitors under no load at 85°C for 1000 hours and then performing voltage treatment based on JIS C 5101-4 clause 4.1 at 20°C, they shall meet the specified values for the endurance characteristics listed above. The capacitors are kept on a hot plate for 30 seconds, which Within ±10% of the initial capacitance value Capacitance change is maintained at 250°C. The capacitors shall meet the Less than or equal to the initial specified value tan δ characteristic requirements listed at right when they are Less than or equal to the initial specified value Leakage current removed from the plate and restored to 20°C. Shelf Life Resistance to soldering heat Marking Black print on the case top. Chip Type 5.4 Voltage mark for 6.3V is C±0.2 1 +0.1 –0.2 6V . φD 0.5 to 0.8 A B C E Dimensions 6.3 0J V Cap. (µF) 0.1 0.22 0.33 0.47 1 2.2 3.3 4.7 10 22 33 47 100 Code 0R1 R22 R33 R47 010 2R2 3R3 4R7 100 220 330 470 101 5 6.3 6.3 8 28 37 45 82 4 6.3 6.3 8 3 4 5 6 7 8 9 10 11 12 13 14 4 1.8 4.3 4.3 1.0 Taping code Configuration Capacitance tolerance (±20%) 5 2.1 5.3 5.3 1.3 10 1A 2 UWP 1 C 1 0 0 M C L 1 G B E B±0.2 φD±0.5 A2 10 16V Plastic platform 0.3 MAX. A±0.2 A±0.2 Voltage Lot No. 0.5 MAX. Type numbering system (Example : 16V 10µF) Capacitance 25 2 4 (mm) 6.3 8 2.4 3.3 6.6 8.3 6.6 8.3 2.2 2.3 Rated capacitance (10µF) Rated voltage (16V) Series name Type 16 1C 17 33 41 61 4 5 6.3 6.3 8 25 1E 12 23 37 49 75 5 5 6.3 8 8 35 1V 12 16 27 50 61 4 5 5 6.3 8 8.4 16 18 29 54 50 1H 4 1.0 4 2.0 4 2.8 4 4.0 4 8.4 5 13 5 17 6.3 20 8 36 Allowable ripple Rated Case size ripple φ D (mm) Rated ripple current (mArms) at 85°C 120Hz Frequency coefficient of rated ripple current Frequency Coefficient 50 Hz 0.70 120 Hz 1.00 300 Hz 1.17 1 kHz 1.36 10 kHz or more 1.50 Taping specifications are given in page 23. Recommended land size, soldering by reflow are given in page 18, 19. Please select UN(p.162) series if high C/V products are reqired. Please refer to page 3 for the minimum order quantity. CAT.8100D