ALUMINUM ELECTROLYTIC CAPACITORS UCV Chip Type, Low Impedance. Chip type, low impedance temperature range up to +105°C. Applicable to automatic mounting machine fed with carrier tape. Compliant to the RoHS directive (2011/65/EU). UCM Smaller Higher capacitance UCV Specifications Item Performance Characteristics Category Temperature Range –55 to +105°C Rated Voltage Range 25 to 35V Rated Capacitance Range 220 to 1000µF Capacitance Tolerance ± 20% at 120Hz, 20°C Leakage Current After 2 minutes' application of rated voltage, leakage current is not more than 0.01CV. Tangent of loss angle (tan δ) Rated voltage (V) tan δ (MAX.) 25 0.14 25 2 3 3 Rated voltage (V) Stability at Low Temperature Measurement frequency : 120Hz at 20°C 35 0.12 Z–25°C / Z+20°C Impedance ratio Z–40°C / Z+20°C ZT / Z20 (MAX.) Z–55°C / Z+20°C 35 2 3 3 Resistance to soldering heat Black print on the case top. Marking Type system (Example : 35V: 35V 220µF) Typenumbering numbering system (Example 220µF) Type numbering system (Example : 35V 220µF) Chip Type 1 1 φD±0.5 φD±0.5 Capacitance Capacitance L±0.5 L±0.5 Pressure relief vent Pressure relief vent 25 35 Code 1E 1V 221 331 470 471 560 561 680 681 820 821 1000 102 5 5 6 6 7 7 8 8 9 10 11 12 13 14 9 10 11 12 13 14 Taping code Taping code Size code Size code Configuration Capacitance tolerance (±20%) Capacitance tolerance (±20%) Rated capacitance (220µF) Rated capacitance (220µF) Rated voltage (35V) Rated voltage (35V) Series name Series name Type Type Rated Voltage Rated Voltage V 25 35 V 25 35 Code E V Code E V Standard φD×L Standard φD×L A A B B C C E E L L H H 6.3×7.7 6.3×7.7 2.4 2.4 6.6 6.6 6.6 6.6 2.2 2.2 7.7 0.57.7 to 0.8 0.5 to 0.8 8×10 8×10 2.9 2.9 8.3 8.3 8.3 8.3 3.1 3.1 10 0.810 to 1.1 0.8 to 1.1 Configuration φd Code φd Code 6.3 CL 6.3 CL 8・10 NL 8・10 NL (mm) (mm) 10×10 10×10 3.2 3.2 10.3 10.3 10.3 10.3 4.5 4.5 10 0.810 to 1.1 0.8 to 1.1 Frequency coefficient of rated ripple current V 330 4 4 Negative Negative H H Dimensions 220 3 3 A±0.2 A±0.2A±0.2 A±0.2 EE C±0.2 C±0.2 EE A2A2 680V 680V CV CV Series Series Negative Negative Positive Positive H H Plastic platform Plastic platform 0.3MAX. 0.3MAX. A±0.2 A±0.2A±0.2 A±0.2 (φ 8 to φ10, φ10) (φ 8 to(Vφ10, Voltage : 35V )φ10) 0.5MAX. 0.5MAX. A2A2 220V 220V CV CV φD±0.5 φD±0.5 L± 0.3 L± 0.3 Capacitance Capacitance Voltage (V : 35V ) C±0.2 C±0.2 B±0.2 B±0.2 Series Series Voltage (C:35V) 2 2 UCV 1 V 2 2 1 MC L 1 GS UCV 1 V 2 2 1 MC L 1 GS Positive Positive 0.5MAX. 0.5MAX. Plastic platform Plastic platform 0.3MAX. 0.3MAX. B±0.2 B±0.2 (φ 6.3) (φ 6.3)(C:35V) Voltage Lot No. Lot No. Within ±30% of the initial capacitance value 200% or less than the initial specified value Less than or equal to the initial specified value After storing the capacitors under no load at 105°C for 1000 hours and then performing voltage treatment based on JIS C 5101-4 clause 4.1 at 20°C, they shall meet the specified values for the endurance characteristics listed above. The capacitors are kept on a hot plate for 30 seconds, Within ±10% of the initial capacitance value Capacitance change which is maintained at 250°C. The capacitors shall meet Less than or equal to the initial specified value tan δ the characteristic requirements listed at right when they Less than or equal to the initial specified value Leakage current are removed from the plate and restored to 20°C. Shelf Life Trade mark Trade mark Capacitance change tan δ Leakage current The specifications listed at right shall be met when the capacitors are restored to 20°C after the rated voltage is applied for 2000 hours at 105°C. Endurance Lot No. Lot No. Measurement frequency : 120Hz 6.3 × 7.7 0.16 600 8 × 10 0.08 850 10 × 10 0.06 1190 0 Frequency0/ Coefficient 6.3 × 7.7 0.16 600 8 × 10 0.08 850 10 × 10 0.06 1190 Impedance Rated ripple × 50Hz 0.35 120Hz 0.50 MAX. Impedance (Ω) at 20℃ 100kHz, MAX. Impedance (Ω) at 20℃ 100kHz, Rated ripple current(mArms) at 105℃ 100kHz Rated ripple current(mArms) at 105℃ 100kHz 300Hz 0.64 1kHz 0.83 10kHz or more 1.00