NICHICON UUD1V221MNL1GS

ALUMINUM ELECTROLYTIC CAPACITORS
UD
Chip Type, Low Impedance
series
Chip type, low impedance temperature range up to +105°C.
Designed for surface mounting on high density PC board.
Applicable to automatic mounting machine fed with carrier tape.
Compliant to the RoHS directive (2011/65/EU).
WD
High
Te m p reflow
UD
Low Impedance
CD
WG
Low Impedance
Specifications
Performance Characteristics
Item
Category Temperature Range
– 55 to +105°C
Rated Voltage Range
6.3 to 50V
Rated Capacitance Range
1 to 1500µF
Capacitance Tolerance
± 20% at 120Hz, 20°C
Leakage Current
After 2 minutes' application of rated voltage, leakage current is not more than 0.01 CV or 3 (µA), whichever is greater.
Measurement frequency : 120Hz at 20°C
Rated voltage (V)
6.3
10
16
25
35
50
tan δ (MAX.)
0.26 (0.28) 0.20 (0.24) 0.16 (0.20) 0.14 (0.16) 0.12 (0.14) 0.12 (0.14)
Tangent of loss angle (tan δ)
(
) is φ8 over
Measurement frequency : 120Hz
6.3
3
5
Rated voltage (V)
Z– 25°C / Z+20°C
Z– 55°C / Z+20°C
Stability at Low Temperature
Impedance ratio
ZT / Z20 (MAX.)
10
2
4
The specifications listed at right shall be met
when the capacitors are restored to 20°C after the
rated voltage is applied for 5000 hours (2000
hours for φD = 4, 5 and 6.3) at 105°C.
Endurance
25
2
3
16
2
4
35
2
3
Capacitance change
tan δ
Leakage current
50
2
3
Within ±30% of the initial capacitance value
200% or less than the initial specified value
Less than or equal to the initial specified value
After storing the capacitors under no load at 105°C for 1000 hours and then performing voltage treatment based on JIS C 5101-4
clause 4.1 at 20°C, they shall meet the specified values for the endurance characteristics listed above.
The capacitors are kept on a hot plate for 30 seconds, which is
Capacitance change Within ±10% of the initial capacitance value
maintained at 250°C. The capacitors shall meet the characteristic
Less than or equal to the initial specified value
tan δ
requirements listed at right when they are removed from the plate
Less than or equal to the initial specified value
Leakage current
and restored to 20°C.
Shelf Life
Resistance to soldering
heat
Black print on the case top.
Marking
Type numbering system (Example : 16V 22µF)
Chip Type
(φ4 to φ6.3)
0.5 MAX.
1
2
3
4
5
6
7
8
9
10 11 12 13 14
A±0.2
UUD 1 C 2 2 0 M C L 1 GS
Package code
Configuration
A±0.2
E
L±0.3
Capacitance
Lot No.
C±0.2
B±0.2
φD±0.5
Series
A2
22C
UD
Voltage (C:16V)
Positive
Plastic platform
0.3 MAX.
H
φD
4 to 6.3
Rated capacitance (22µF)
8 • 10
Rated voltage (16V)
Capacitance tolerance (±20%)
Negative
Code
CL
NL
Series name
Type
(φ8 to φ10 )
Lot No.
10
A
16
C
25
E
35
V
0.5 MAX.
(mm)
φD×L
A±0.2 A±0.2
E
L±0.5
Capacitance
Negative
Pressure relief vent
Voltage
V
6.3
Code
j
C±0.2
B±0.2
A2
100V
UD
Trade mark
Plastic platform
0.3 MAX.
Series
φD±0.5
Voltage (V:35V)
Positive
A
B
C
E
L
H
4 × 5.8
5 × 5.8
6.3 × 5.8
6.3 × 7.7
8 × 10
10 × 10
1.8
4.3
4.3
1.0
5.8
0.5 to 0.8
2.1
5.3
5.3
1.3
5.8
0.5 to 0.8
2.4
6.6
6.6
2.2
5.8
0.5 to 0.8
2.4
6.6
6.6
2.2
7.7
0.5 to 0.8
2.9
8.3
8.3
3.1
10
0.8 to 1.1
3.2
10.3
10.3
4.5
10
0.8 to 1.1
H
50
H
Dimension table in next page.
CAT.8100C
ALUMINUM ELECTROLYTIC CAPACITORS
UD
series
Dimensions
Cap.
(µF)
V
6.3
10
16
25
35
50
Code
0J
1A
1C
1E
1V
1H
1
010
4 × 5.8
5.00
30
2.2
2R2
4 × 5.8
5.00
30
3.3
3R3
4 × 5.8
5.00
30
4.7
4R7
10
100
15
150
22
220
27
270
4 × 5.8
1.80
33
330
5 × 5.8
47
470
56
4 × 5.8
1.80
80
5 × 5.8
1.52
85
6.3 × 5.8
0.88
165
4 × 5.8
1.80
80
5 × 5.8
0.76
150
4 × 5.8
1.80
80
5 × 5.8
0.76
150
5 × 5.8
0.76
150
6.3 × 5.8
0.88
165
4 × 5.8
1.80
80
5 × 5.8
0.76
150
5 × 5.8
0.76
150
5 × 5.8
0.76
150
6.3 × 5.8
0.88
165
80
5 × 5.8
0.76
150
5 × 5.8
0.76
150
6.3 × 5.8
0.44
230
6.3 × 5.8
0.44
230
6.3 × 7.7
0.68
185
0.76
150
5 × 5.8
0.76
150
6.3 × 5.8
0.44
230
6.3 × 5.8
0.44
230
6.3 × 5.8
0.44
230
6.3 × 7.7
0.68
185
5 × 5.8
0.76
150
6.3 × 5.8
0.44
230
6.3 × 5.8
0.44
230
6.3 × 5.8
0.44
230
6.3 × 5.8
0.44
230
6.3 × 7.7
0.68
185
560
5 × 5.8
0.76
150
6.3 × 5.8
0.44
230
6.3 × 5.8
0.44
230
6.3 × 5.8
0.44
230
6.3 × 7.7
0.34
280
8 × 10
0.34
300
68
680
6.3 × 5.8
0.44
230
6.3 × 5.8
0.44
230
6.3 × 5.8
0.44
230
6.3 × 5.8
0.44
230
6.3 × 7.7
0.34
280
8 × 10
0.34
300
100
101
6.3 × 5.8
0.44
230
6.3 × 5.8
0.44
230
6.3 × 5.8
0.44
230
6.3 × 7.7
0.34
280
8 × 10
0.17
450
8 × 10
0.34
300
150
151
6.3 × 5.8
0.44
230
6.3 × 5.8
0.44
230
6.3 × 7.7
0.34
280
8 × 10
0.17
450
8 × 10
0.17
450
10 × 10
0.18
670
220
221
6.3 × 5.8
0.44
230
6.3 × 7.7
0.34
280
6.3 × 7.7
0.34
280
8 × 10
0.17
450
8 × 10
0.17
450
10 × 10
0.18
670
330
331
6.3 × 7.7
0.34
280
8 × 10
0.17
450
8 × 10
0.17
450
8 × 10
0.17
450
10 × 10
0.09
670
470
471
8 × 10
0.17
450
8 × 10
0.17
450
8 × 10
0.17
450
10 × 10
0.09
670
680
681
8 × 10
0.17
450
10 × 10
0.09
670
10 × 10
0.09
670
1000
102
8 × 10
0.17
450
10 × 10
0.09
670
1500
152
10 × 10
0.09
670
Case size
φ D × L (mm)
Impedance
Rated
ripple
Max. Impedance (Ω) at 20°C 100kHz,
Rated ripple current (mArms) at 105°C 100kHz
Frequency coefficient of rated ripple current
Frequency
Coefficient
50 Hz
0.35
120 Hz
0.50
300 Hz
0.64
1 kHz
0.83
10 kHz or more
1.00
Taping specifications are given in page 23.
Recommended land size, soldering by reflow are given
in page 18, 19.
Please refer to page 3 for the minimum order quantity.
CAT.8100C