ALUMINUM ELECTROLYTIC CAPACITORS WG Chip Type, Low Impedance series Chip type, operating over wide temperature range of to – 55 to +105°C. Designed for surface mounting on high density PC board. Applicable to automatic mounting machine fed with carrier tape. Compliant to the RoHS directive (2002/95/EC). Low Impedance UD Low Impedance WG WF Specifications Item Performance Characteristics Category Temperature Range – 55 to +105°C Rated Voltage Range 6.3 to 50V Rated Capacitance Range 1 to 1500µF Capacitance Tolerance ± 20% at 120Hz, 20°C Leakage Current After 2 minutes' application of rated voltage, leakage current is not more than 0.01CV or 3 (µA) , whichever is greater. Measurement frequency : 120Hz at 20°C Tangent of loss angle (tan δ) 6.3 0.26 Rated voltage (V) tan δ (MAX.) 10 0.19 16 0.16 25 0.14 35 0.12 50 0.12 Measurement frequency : 120Hz 6.3 2 4 Rated voltage (V) Z– 25°C / Z+20°C Impedance ratio Z– 55°C / Z+20°C ZT / Z20 (MAX.) Stability at Low Temperature 10 2 4 16 2 3 35 2 3 25 2 3 50 2 3 The specifications listed at right shall be met Capacitance change Within ±20% of the initial capacitance value when the capacitors are restored to 20°C tan δ 200% or less than the initial specified value after the rated voltage is applied for 1000 Leakage current Less than or equal to the initial specified value hours at 105°C. After storing the capacitors under no load at 105°C for 1000 hours and then performing voltage treatment based on JIS C 5101-4 clause 4.1 at 20°C, they shall meet the specified values for the endurance characteristics listed above. The capacitors are kept on a hot plate for 30 seconds, which is Capacitance change Within ±10% of the initial capacitance value maintained at 250°C. The capacitors shall meet the characteristic tan δ Less than or equal to the initial specified value requirements listed at right when they are removed from the plate Leakage current Less than or equal to the initial specified value and restored to 20°C. Endurance Shelf Life Resistance to soldering heat Black print on the case top. Marking Type numbering system (Example : 10V 100µF) Chip Type 1 (φ4 to φ6.3) Positive Plastic platform 0.3 MAX. Voltage 0.5 MAX. Capacitance C±0.2 3 4 5 6 7 8 9 10 11 12 13 14 Taping code A±0.2 φD code 4 to 6.3 GB 8 • 10 GS A±0.2 E B±0.2 φD±0.5 A2P 100 6V 105°C Marking 2 UWG 1 A 1 0 1 M C L 1 G S +0.1 L -0.2 Lot No. Capacitance tolerance (±20%) Negative H Rated capacitance (100µF) (φ8 × 6.2 ) Positive Plastic platform 0.3 MAX. Voltage C±0.2 Series name A±0.2 Type A±0.2 E B±0.2 A2P 100 10V φD±0.5 Trade mark Rated voltage (10V) 0.5 MAX. Capacitance 105°C Marking L±0.3 Lot No. (φ8 × 10, φ10 × 10 ) Plastic platform 0.3 MAX. Voltage C±0.2 A±0.2 φD × L A B C E L H 4 × 5.4 5 × 5.4 6.3 × 5.4 8 × 6.2 8 × 10 10 × 10 3.2 2.9 3.3 2.4 2.1 1.8 10.3 8.3 8.3 6.6 5.3 4.3 10.3 8.3 8.3 6.6 5.3 4.3 4.5 3.1 2.3 2.2 1.3 1.0 10 10 6.2 5.4 5.4 5.4 0.5 to 0.8 0.5 to 0.8 0.5 to 0.8 0.5 to 0.8 0.8 to 1.1 0.8 to 1.1 A±0.2 E B±0.2 φD±0.5 A2P 220 25V Trade mark 0.5 MAX. Positive Capacitance (mm) Negative H 105°C Marking Configuration φD code 4 to 6.3 CL 8 (6.2L) CL 8 (10L) • 10 NL L±0.5 Lot No. Pressure relief vent H Negative Voltage mark for 6.3V is 6V . Dimension table in next page. CAT.8100B ALUMINUM ELECTROLYTIC CAPACITORS WG series Dimensions Cap. (µF) V 6.3 10 16 Code 0J 1A 1C 4 × 5.4 3.0 60 5 × 5.4 1.8 95 95 6.3 × 5.4 1.0 140 140 8 × 6.2 0.4 230 8 × 6.2 0.4 230 10 × 10 0.15 670 10 × 10 0.15 670 10 × 10 0.15 670 10 × 10 0.15 670 10 100 22 220 33 330 47 470 5 × 5.4 1.8 68 680 6.3 × 5.4 1.0 100 101 6.3 × 5.4 1.0 140 150 151 220 221 8 × 6.2 0.4 230 330 331 8 × 10 0.3 450 470 471 680 681 1000 102 10 × 10 0.15 670 1500 152 10 × 10 0.15 670 Cap. (µF) 4 × 5.4 60 3.0 5 × 5.4 1.8 95 8 × 6.2 0.4 230 8 × 6.2 0.4 230 8 × 10 0.3 450 10 × 10 10 × 10 0.15 0.15 670 670 V 25 35 50 Code 1E 1V 1H 1 010 4 × 5.4 3.0 60 4 × 5.4 5.0 30 2.2 2R2 4 × 5.4 3.0 60 4 × 5.4 5.0 30 3.3 3R3 4 × 5.4 3.0 60 4 × 5.4 5.0 30 4.7 4R7 4 × 5.4 3.0 60 5 × 5.4 3.0 50 6.8 6R8 95 4 × 5.4 3.0 60 5 × 5.4 1.8 10 100 5 × 5.4 1.8 95 6.3 × 5.4 2.0 70 22 220 6.3 × 5.4 1.0 140 6.3 × 5.4 1.0 140 8 × 6.2 0.7 120 33 330 6.3 × 5.4 1.0 140 8 × 6.2 0.4 230 8 × 10 0.6 300 47 470 8 × 6.2 0.4 230 8 × 6.2 0.4 230 10 × 10 0.3 500 68 680 8 × 10 0.3 450 100 101 8 × 10 0.3 450 10 × 10 0.15 670 10 × 10 0.3 500 220 221 10 × 10 0.15 670 10 × 10 0.15 670 10 × 10 0.3 330 331 10 × 10 0.15 670 10 × 10 0.15 670 470 471 10 × 10 0.15 670 Case size φ D × L (mm) 500 Impedance Rated ripple Max. Impedance (Ω) at 20°C 100kHz Rated ripple current (mArms) at 105°C 100kHz Frequency coefficient of rated ripple current Frequency Coefficient 50 Hz 0.35 120 Hz 0.50 300 Hz 0.64 1 kHz 0.83 10 kHz or more 1.00 Taping specifications are given in page 23. Recommended land size, soldering by reflow are given in page 18, 19. Please select UJ(p.116) series if high C/V products are reqired. Please refer to page 3 for the minimum order quantity. CAT.8100B