Products / Radial Lead Type

CAT. 8200C
Aluminum Solid Electrolytic Capacitors
with Functional Polymer
2013
NICHICON CORPORATION / FPCAP ELECTRONICS (SUZHOU) CO., LTD.
CONTENTS
Page
Precautions
Critical Precautions on FPCAP itself
General Precautions at Designing, for Use and Handling
Products List
Green Products
System Diagram
Products / Radial Lead Type
NS series
R7 series
R5 series
L8 series
E5 series
S8 series
F8 series
NU series
NE series
S6 series
HT series
1
2
6
6
7
8
10
12
14
16
18
20
22
24
26
28
Products / SMD Type
PS , PA series
HS , HA series
SS , SA , SB series
FS , FA series
SL series
VA , VB , VC series
UA , UB series
Ordering Information
Packing Specifications
Materials and Soldering
Technical Guide
Estimating of Lifetime
Application Guide
Memo
30
32
34
36
38
40
42
44
45
48
50
56
58
60
NICHICON CORPORATION / FPCAP ELECTRONICS (SUZHOU) CO., LTD.
Precautions
Functional Polymer Aluminum Solid Electrolytic Capacitors
Critical Precautions on
itself
1. Polarity
The FPCAP has polarity. Consequently, make sure polarity is never reversed when using.
If polarity is reversed, leakage current could increase or lifetime could decrease.
2. Applied Voltage
Under no circumstances can reverse voltage be applied. It may cause a short circuit.
3. Sudden charge and discharge
Keep sudden charge and discharge to a minimum. It may create a short circuit or cause high leakage current.
In this case, it is recommended to use a protection circuit in order to maintain high reliability.
Regardless, using protection circuit to ensure reliability is recommended when the rush current value exceeds 10A.
Please make sure to insert a protection resistor of about 1kΩ for charge and discharge when measuring the leakage current.
4. Soldering
The soldering conditions must be kept within the permissible range prescribed in the catalog specification.
If the specification is not kept, there is the possibility of abnormal appearance and abnormal leakage current and reduced capacitance.
5. Installation on PC board
When designing the layout of your PC board using the FPCAP please take into consideration the standard mounting specifications.
The FPCAP can not be able to be mounted on a PC board if there is insufficient space.
6. Directions for use in circuits
Since leakage current fluctuations can occur during the soldering process the FPCAP cannot be used in the following circuits.
(1) High impedance voltage retention circuits
(2) Coupling circuits
(3) Time constant circuits
(4) Circuits greatly affected by leakage current
(5) Connecting two or more FPCAP in series
NICHICON CORPORATION / FPCAP ELECTRONICS (SUZHOU) CO., LTD.
1
Precautions
General Precautions at Designing, for Use and Handling
1. Circuit design precautions
(1) Check the rated performance
After checking the operation and installation environments, design the circuit so that it falls within the rated performance range
stipulated in the catalog specification.
(2) Operating temperature and ripple current
a) Set the operating temperature so that it falls within the range stipulated in the catalog specification.
b) Do not apply current that exceeds the allowable ripple current in the catalog.
(3) Leakage current
Even when the soldering conditions fall within the range of the catalog specification, the leakage current increases slightly.
It also increases slightly during high temperature no-load, moisture-proof no-load and temperature cycling tests with
no voltage applied.
In cases such as these, leakage current will decrease by applying voltage in conditions below the maximum operating temperature.
(4) Applied voltage Considerations
a) Make sure the sum of the peak DC voltage and ripple voltage values does not exceed the rated voltage.
b) Please do not apply the reverse voltage to FPCAP.
c) When the DC voltage is low, please check whether the peak value of ripple voltage does not become a reverse voltage.
(5) Reduction of failure stress
The main failure mode of the FPCAP is in the open mode primarily caused by an electrostatic capacitance drop.
Random short circuit mode failures occur rarely.
The time it takes to reach the failure mode can be extended by using the FPCAP with reduced ambient temperature,
ripple current and applied voltage.
(6) Capacitor insulation
a) Insulation is not guaranteed.
b) Be sure to completely separate the case, negative electrode terminal and positive electrode terminal from adjacent components
and PC board traces.
(7) Operating environment
Do not use the FPCAP in the following environments.
a) Places where it can come into direct contact with water or salt water and places where condensation may form.
b) Places filled with noxious gasses such as: hydrogen sulfide, sulfurous acid, nitrous acid, chlorine, ammonia, etc.
c) Places exposed to ozone, ultraviolet rays and radiation.
d) Where severe vibration or shock which exceeds the condition specified in the specification sheets.
(8) Assembly Conditions Considerations
In designing a circuit, the following conditions should be checked before the FPCAP is mounted on the PC board.
a) The pitch and diameter of PCB holes to which the FPCAP is mounted, shall be designed in conformance with the dimensional
tolerance stipulated in the catalog specifications.
(9) PC board
Avoid locating heat-generating components around the FPCAP and on the underside of the PC board under the FPCAP.
(10) Parallel connection
When used in a parallel connection with another capacitor, carefully select the type of capacitor.
(11) Other
a) Electrical characteristics are affected by fluctuations in temperature and frequency.
b) When mounting the FPCAP on a double-sided PC board, design the board so that extra PC board holes are not located
underneath the FPCAP.
2
NICHICON CORPORATION / FPCAP ELECTRONICS (SUZHOU) CO., LTD.
Precautions
2. Mounting precautions
(1) Things to know before mounting
a) Do not reuse the FPCAP that has already been assembled in a device and energized.
Excluding the FPCAP that has been removed for measuring electrical characteristics during a periodic inspection,
they cannot be reused.
b) Leakage current may increase if the part has been stored for a long period of time.
In this case, use after voltage treatment under the rated voltage.
c) There are non-halogen types of flux that do not contain ionic halides, but contain many non-ionic halides.
When these non-ionic halides infiltrate the capacitor, they also cause a harmful reaction.
Use soldering flux that does not contain non-ionic halides, also ionic halides.
(2) Mounting-1
a) Mount after checking the capacitance and the rated voltage.
b) Mount after checking the polarity.
c) Do not drop on the floor and do not use parts that have been dropped.
d) Do not deform and then mount.
(3) Mounting-2
a) Mount after checking the match between the lead pitch and the PC board holes pitch.
b) When an automatic insertion equipment is used to clinch the lead wires, make sure it is set correctly.
c) Be careful of the shock force that can be produced by the automatic insertion equipment.
d) Do not apply excessive external force to the lead wires, the FPCAP itself, or the electrode terminals.
(4) Soldering with a soldering iron
a) Set the soldering conditions (temperature, time) so that they fall within the range stipulated by the catalog specification.
b) When the lead wire terminal must be processed because the terminal spacing and the PC board holes spacing do not match,
process it before soldering so that no stress is applied to the FPCAP itself.
c) Do not subject the FPCAP itself to excessive stress when soldering with a soldering iron.
d) When a soldering iron is used to repair the FPCAP that has already been soldered once and needs to be removed,
do it after the solder has been completely melted so that no stress is applied to the FPCAP terminals.
e) Do not let the tip of the soldering iron touch the FPCAP itself.
f ) The amount of leakage current after soldering may increase a slightly (from a few μA to several hundred μA) depending
on the soldering condition (preheating and solder temperature and time, PC board material and thickness, etc.)
The leakage current can be reduced by applying voltage.
(5) Flow soldering (Radial lead type)
a) Never submerge the FPCAP in molten solder. Use the PC board to protect the FPCAP and only solder the opposite side
of the board that the FPCAP is mounted on.
b) Set the soldering conditions (soldering temperature, terminal submersion time) so that they fall within the range stipulated
by the catalog specification. The amount of leakage current after soldering may increase slightly (from a few μA to several
hundred μA) depending on the soldering conditions (preheating and solder temperature and time, PC board material and
thickness, etc.). The leakage current can be reduced through self-repair by applying voltage.
c) Take care that flux does not adhere to any place other than the terminals.
d) When soldering, take care that other components do not fall over and touch the FPCAP.
e) Flow soldering under extremely abnormal conditions may reduce the capacitance of products before or after soldering.
(6) Reflow soldering (SMD type)
Do not use reflow soldering for Radial lead type (Through Hole).
a) Never submerge the FPCAP in molten solder. Use the PC board to protect the FPCAP and only solder the opposite side
of the board that the FPCAP is mounted on.
b) Set the soldering conditions (soldering temperature, terminal submersion time) so that they fall within the range stipulated
by the catalog specification. The amount of leakage current after soldering may increase slightly (from a few μA to several
hundred μA) depending on the soldering conditions (preheating and solder temperature and time, PC board material and
thickness, etc.). The leakage current can be reduced through self-repair by applying voltage.
c) Take care that flux does not adhere to any place other than the terminals.
d) When soldering, take care that other components do not fall over and touch the FPCAP.
e) Reflow soldering under extremely abnormal conditions may reduce the capacitance of products before or after soldering.
f) Do not use VPS (Vapor Phase Soldering).
NICHICON CORPORATION / FPCAP ELECTRONICS (SUZHOU) CO., LTD.
3
Precautions
(7) Handling after soldering
a) Do not tilt, bend or twist the FPCAP after it has been soldered on the PC board.
b) Do not use the FPCAP as a handle to move the PC board after it has been attached to it.
c) Do not bump the FPCAP with objects after it has been soldered to the PC board. Make sure the FPCAP does not touch
other PC boards or components.
d) Do not subject to excessive stress after it has been soldered to the PC board.
(8) Washing the PC board
Check the following items before washing the PC board with these detergents; high quality alcohol-based cleaning fluid such as
Pine-αST-100S, Clean-thru 750H, 750L, 750K, or Techno Care FRW14 through 17; or detergents including substitute
Freon such as AK-225AES and IPA.
a) Use immersion or ultrasonic wave to clean for a total of less than five minutes.
b) The temperature of the cleaning fluid should be less than 60°C.
c) Watch for contamination of the detergent (conductivity, pH, specific gravity, water content, etc.).
d) After cleaning do not store in a location subject to gases from the cleaning fluid or in an airtight container.
Dry the PC board and the FPCAP using hot air (less than the maximum operating temperature).
e) Please contact our company for details about detergents and cleaning methods, and about detergents other than those
listed above.
(9) Fixatives and coatings
a) Select appropriate material for the FPCAP marking material and sealant.
In particular, make sure the fixative, coating and thinner do not contain acetone or toluene.
b) Before applying a fixative or coating, completely remove any flux residue and foreign matter from the area where the PC board
and the FPCAP are to be joined together.
c) Allow any detergent to dry before applying the fixative or coating.
d) Please contact our company for fixative and coating heat curing conditions.
3. Precautions with completed board
(1) Do not directly touch the FPCAP terminals.
(2) Do not use electric conductors to cause a short circuit between the FPCAP terminals.
Do not subject the FPCAP to conductive solutions.
(3) Check the installation environment of the board on which the FPCAP is mounted.
(4) Aging of the completed board, please use the voltage below the rated voltage of the capacitor.
(5) It is recommended that the board be used at room temperature and in ordinary humidity.
For details, refer to the Operating Precaution Guidelines for the EIAJ RCR-2367C. (Safety Application Guide for fixed
aluminum electrolytic capacitors for use in electronic equipment.)
No part of this publication shall be reproduced without prior written permission of the publisher.
4. If trouble should occur
(1) In the event that a short circuit causes the current to become relatively small (Radial lead type : less than approximately
3A for φ10 and less than approximately 1A for φ6.3), the FPCAP itself will generate some heat, but the appearance
will not be affected even when electricity is supplied continuously. However, if there is a short circuit and the current value
exceeds the above mentioned values, the temperature inside the FPCAP will increase.
When the temperature exceeds approximately 200°C the internal pressure will increase, and an odorous gas will be released.
In this case, do not allow contact with your face and hands.
(2) If a short circuit occurs and an odorous gas is released, either turn off the device’s main power or unplug the power cord from
the outlet.
(3) If a short circuit should occur, it may take anywhere from a few seconds to a few minutes until an odorous gas develops,
depending on the conditions. Design the device so that a power protection circuit works during this time period.
4
NICHICON CORPORATION / FPCAP ELECTRONICS (SUZHOU) CO., LTD.
Precautions
(4) If the gas gets in your eyes, rinse them immediately. If it has been inhaled, gargle with water immediately.
(5) When the polymer or gas of the polymer comes in contact with your skin, wash it off with soap and water.
(6) The electrolyte, separator paper, rubber and tube used in the FPCAP are all combustible. When the current value is
extraordinarily high during a short circuit, and assuming the worst possibility, the shorted-out section in the lead wire or
inside the capacitor could create a spark, and cause the resin or tube to catch fire.
Give due consideration to the capacitors mounting methods, mounting positions, pattern design etc.
5. Storage conditions
Do not store capacitors without load more than a year because of potential increased leakage current.
(1) Do not store at high temperatures and high humidity. Store it in a location that is not subject to direct sunlight and that has
low temperatures and humidity (generally, temperatures between 5 and 35ºC and a relative humidity of 75% or less).
(SMD type VA/VB series : Temperatures between 5 and 30ºC and a relative humidity of 70% or less)
(2) Storage period (SMD type VA/VB series)
Store in an aluminum laminated bag.
Before opening : 1 year
After opening : 1 week (Use up all the products after having opened out. Surplus products should be put into the aluminum
laminated bag, and seal up.)
(3) Baking conditions (SMD type VA/VB series)
When you use it exceeding a storage term, please carry out and use baking by the following conditions.
Temperature: 60(+0, -5) ºC
Time: 168hours (only one time)
(4) Store in an airtight plastic bag to keep the leads in good condition.
(5) To keep the leads in good condition, store lead-type the FPCAP for no more than one year.
(6) Do not store in places where water, salt water or oil can directly fall on them, or places where condensation may form.
(7) Do not store in places filled with noxious gas (hydrogen sulfide, sulfurous acid, nitrous acid, chlorine, ammonia, etc.).
(8) Do not store in places exposed to ozone, ultraviolet rays and radiation.
6. Disposal
Please treat the FPCAP as industrial waste when needing to dispose of the FPCAP.
For details, refer to the Operating Precaution Guidelines for the EIAJ RCR-2367C. (Safety Application Guide for fixed
aluminum electrolytic capacitors for use in electronic equipment.)
No part of this publication shall be reproduced without prior written permission of the publisher.
NICHICON CORPORATION / FPCAP ELECTRONICS (SUZHOU) CO., LTD.
5
Products List, Green Products
Products List
Classification
Series
Note
Rated
Voltage
Range
Capacitance
Range
Categorical
Max. Temp.
and Endurance
Pages
NS
Standard
4.0 to 25V
10 to 1200μF
105ºC 2000Hrs
8
R7
Low ESR
2.5 to 16V
68 to 1500μF
105ºC 2000Hrs
10
R5
Ultra-Low ESR
2.5 to 6.3V
390 to 1500μF
105ºC 2000Hrs
12
L8
Low ESR and Low Profile (φ8)
2.5 to 35V
100 to 1500μF
105ºC 2000/5000Hrs
14
E5
Ultra-Low ESR and Low Profile (φ8)
2.5 to 4.0V
560 to 820μF
105ºC 2000Hrs
16
S8
Low ESR/ESL and Low Profile (φ6.3)
2.5 to 16V
100 to 1200μF
105ºC 2000/5000Hrs
18
F8
Low ESR/ESL and Low Profile (φ5)
2.5 to 6.3V
100 to 560μF
105ºC 2000Hrs
20
NU
Large Capacitance
2.5 to 63V
10 to 2700μF
105ºC 2000/5000Hrs
22
NE
Large Capacitance
2.5 to 16V
100 to 1200μF
105ºC 2000Hrs
24
S6
Miniature Sized Large Capacitance
2.5 to 25V
33 to 560μF
105ºC 2000Hrs
26
HT
High Temperature (125ºC)
6.3 to 20V
150 to 820μF
125ºC 1000Hrs
28
PS/PA
Standard (φ6.3 , φ8 , φ10)
2.5 to 63V
8.2 to 1500μF
105ºC 2000Hrs
30
HS/HA
Large Capacitance (φ8)
2.5 to 35V
100 to 1500μF
105ºC 2000Hrs
32
Large Capacitance (φ6.3)
2.5 to 35V
10 to 560μF
105ºC 2000Hrs
34
Large Capacitance (φ4 , φ5)
2.5 to 25V
10 to 330μF
105ºC 2000Hrs
36
Low Profile (φ6.3)
2.5 to 25V
15 to 330μF
105ºC 2000Hrs
38
VA/VB/VC
Molded Chip (7.3¯4.3¯2.8)
Standard / Low ESR
2.0 to 25V
15 to 330μF
105ºC 1000Hrs
40
UA/UB
Molded Chip (7.3¯4.3¯1.9)
Low Profile / Low ESR
2.0 to 25V
15 to 220μF
105ºC 1000Hrs
42
Radial Lead
Type
SS/SA/SB
FS/FA
SMD Type
SL
Green Products
Corresponding to the Environmental Requirement
Classification
Lead-free
RoHS compliance
Halogen-free
Radial Lead Type
SMD Type
: Completed
6
NICHICON CORPORATION / FPCAP ELECTRONICS (SUZHOU) CO., LTD.
System Diagram
System Diagram for FPCAP
Radial Lead Type
Standard
NS series
φ6.3×7 / 10 φ8×11.5, φ10×12.5
z4.0 to 25V
z10 to 1200µF
z105ºC, 2000h
ESR 7mΩ
Low
ESR
R7 series
φ8×11.5, φ10×12.5
z2.5 to 16V
z68 to 1500µF
z105ºC, 2000h
ESR 5mΩ
Low
ESR
R5 series
φ8×11.5, φ10×2.5
z2.5 to 6.3V
z390 to 1500µF
z105ºC, 2000h
Large
Cap.
Low
Profile
Low
Profile
Large Cap.
Low Profile
L8 series
E5 series
NU series
φ4×5, φ6.3×10, φ8×11.5, φ10×12.5
z2.5 to 63V
z10 to 2700µF
z105ºC, 2000h / 5000h
φ8×8
z2.5 to 35V
z100 to 1500µF
z105ºC, 2000h / 5000h
Large
Cap.
Low
ESL
Large Cap.
NE series
Low ESL / Large Cap.
S8 series
ESR 5mΩ
Low
ESR
High
Temperature
φ6.3×8
z2.5 to 16V
z100 to 1200µF
z105ºC, 2000h / 5000h
φ5×8 /10,φ6.3×10,φ8×6 to11.5, φ10×12.5
z2.5 to 16V
z100 to 1200µF
z105ºC, 2000h
Large
Cap.
Low
ESL
Miniature Large Cap.
S6 series
Low ESL / Large Cap.
F8 series
φ6.3×5, φ6.3×6
z2.5 to 25V
z33 to 560µF
z105ºC, 2000h
z2.5 to 6.3V
z100 to 560µF
z105ºC, 2000h
Guarantee 125ºC
HT series
φ8×11.5, φ10×12.5
z6.3 to 20V
z150 to 820µF
z125ºC, 1000h
φ5×8
SMD Type
Molded Chip
Standard
PS series
φ6.3×5.7, φ8×6.7 / 11.7, φ10×7.7 / 12.4
z2.5 to 63V
z8.2 to 1500µF
z105ºC, 2000h
φ8×8
z2.5 to 4V
z560 to 820µF
z105ºC, 2000h
Low
ESR
Standard / Low ESR
Low ESR
series
VA/VB/VC series
PA
7.3×4.3×2.8
z2.0 to 25V
z15 to 330µF
z105ºC, 1000h
φ6.3×5.7, φ8×11.7, φ10× 7.7
z4.0 to 16V
z39 to 560µF
z105ºC, 2000h
Low
Profile
Large
Cap.
Large Cap.
HS series
φ8×6.7, φ8×7.7, φ8×8.7, φ8×11.7
z2.5 to 35V
z100 to 1500µF
z105ºC, 2000h
Low
ESR
Low ESR
series
Low Profile / Low ESR
UA/UB series
HA
7.3×4.3×1.9
z2.0 to 25V
z15 to 220µF
z105ºC, 1000h
φ8×6.7, φ8×7.7
z2.5 to 16V
z150 to 1000µF
z105ºC, 2000h
Large
Cap.
z2.5 to 35V
z10 to 560µF
z105ºC, 2000h
φ6.3×5.7
Low
ESR
φ6.3×5.7, φ6.3×7.7
z2.5 to 16V
z100 to 560µF
z105ºC, 2000h
Large
Cap.
Large Cap.
FS series
φ4×5.2, φ5×5.7
z2.5 to 25V
z10 to 180µF
z105ºC, 2000h
Low ESR
Low ESR
SA series
Low
ESR
Low ESR
FA series
φ5×5.7
z2.5V
z330µF
z105ºC, 2000h
Low
ESR
L
Pr ow
of
ile
Large Cap.
SS series
SB series
φ6.3×5.7
z2.5 to 6.3V
z220 to 560µF
z105ºC, 2000h
Low Profile
SL series
φ6.3×4.2
z2.5 to 25V
z15 to 330µF
z105ºC, 2000h
NICHICON CORPORATION / FPCAP ELECTRONICS (SUZHOU) CO., LTD.
7
Products / Radial Lead Type
Functional Polymer Aluminum Solid Electrolytic Capacitors
NS series
Low ESR
Lead-free
zFeatures
RoHS
Compliance
By using Functional Polymer cathode, Frequency & Temp.
characteristics are greatly improved.
‘ Low ESR at a high frequency range.
‘ High ripple current capability.
‘ Long life and high reliability.
zApplications
‘ Switching Power Supply and DC/DC Converter.
‘ Back up Power Supplies of CPU(VRM etc.)
‘ Miniature high Power Supply.
zEnvironmental Correspondence
Corresponding to Lead-free, RoHS compliance and Halogen-free.
‘ The Lead-free of terminal plating (Sn)
zSpecifications
Characteristics
NS
-55 to +105°C
4.0 to 25V·DC
10 to 1200μF
±20% (M)
105°C 2000Hrs at rated voltage
Within ±20% of the value before test
Not to exceed the value specified
Not to exceed 150% of the value specified
0.1% / 1000Hrs. Max (60%CL)
zSize List
R.V (S.V.)
[V]
Cap. [μF]
10
15
22
33
47
68
100
150
180
220
330
390
470
560
680
820
1000
1200
8
[φD×L]
4.0
(4.6)
6.3
(7.2)
10
(11.5)
6.3×7
6.3×7
6.3×10
8×11.5
8×11.5
8×11.5
10×12.5
8×11.5
10×12.5
10×12.5
10×12.5
10×12.5
6.3×7
6.3×7
6.3×10
8×11.5
8×11.5
10×12.5
8×11.5
10×12.5
10×12.5
10×12.5
8×11.5
16
(18.4)
20
(23)
6.3×7
6.3×7
6.3×10
8×11.5
8×11.5
10×12.5
zDimensions
25
(28.7)
6.3×7
6.3×10
8×11.5
10×12.5
10×12.5
Aluminum Case
Stand off
Wire (Lead free)
P± 0.5
Operating Temp. Range
Rated Voltage Range
Capacitance Range
Capacitance Tolerance
Condition
Capacitance
Endurance
Leakage Current
tan δ
Failure Rate
φD+0.5Max
Items
φd
L+α Max
15Min
4Min
10×12.5
[Unit : mm]
φD×L
6.3×7
φd
0.45
P
2.5
α
1.0
6.3×10
0.5
2.5
1.0
8×11.5
0.6
3.5
1.5
10×12.5
0.6
5.0
1.5
10×12.5
NICHICON CORPORATION / FPCAP ELECTRONICS (SUZHOU) CO., LTD.
zPart number & Specifications
Rated
Voltage
Rated
Capacitance
(V)
(μF, 120Hz)
4.0
6.3
10
16
20
25
Part Number
Leakage
Current *
tanδ
ESR
Rated Ripple
Current
Case Size
(μA, 2 min)
φD×L(mm)
NICHICON
FPCAP
(120Hz)
(mΩ, 100kHz)
(mA, r.m.s.)
560
RNS0G561MDN1††
FP-4R0RE561M-NS††
336
0.08
10
5230
8 × 11.5
820
RNS0G821MDN1††
FP-4R0RE821M-NS††
492
0.08
10
5500
10 × 12.5
1200
RNS0G122MDN1††
FP-4R0RE122M-NS††
720
0.15
10
5500
10 × 12.5
47
RNS0J470MDS1††
FP-6R3RE470M-NS††
50
0.07
42
2050
6.3 × 7
150
RNS0J151MDN1††
FP-6R3RE151M-NS††
142
0.07
21
3900
8 × 11.5
220
RNS0J221MDN1††
FP-6R3RE221M-NS††
208
0.07
21
3900
8 × 11.5
330
RNS0J331MDN1††
FP-6R3RE331M-NS††
312
0.07
10
5500
10 × 12.5
390
RNS0J391MDN1††
FP-6R3RE391M-NS††
369
0.08
10
5230
8 × 11.5
680
RNS0J681MDN1††
FP-6R3RE681M-NS††
643
0.08
10
5500
10 × 12.5
820
RNS0J821MDN1††
FP-6R3RE821M-NS††
775
0.12
10
5500
10 × 12.5
1000
RNS0J102MDN1††
FP-6R3RE102M-NS††
945
0.12
10
5500
10 × 12.5
33
RNS1A330MDS1††
FP-010RE330M-NS††
50
0.07
49
1900
6.3 × 7
68
RNS1A680MDS1††
FP-010RE680M-NS††
102
0.07
35
2650
6.3 × 10
100
RNS1A101MDN1††
FP-010RE101M-NS††
150
0.07
21
3900
8 × 11.5
220
RNS1A221MDN1††
FP-010RE221M-NS††
330
0.07
10
5500
10 × 12.5
470
RNS1A471MDN1††
FP-010RE471M-NS††
705
0.08
10
5500
10 × 12.5
22
RNS1C220MDS1††
FP-016RE220M-NS††
53
0.06
49
1900
6.3 × 7
33
RNS1C330MDS1††
FP-016RE330M-NS††
79
0.06
49
1900
6.3 × 7
47
RNS1C470MDS1††
FP-016RE470M-NS††
113
0.06
42
2400
6.3 × 10
68
RNS1C680MDN1††
FP-016RE680M-NS††
163
0.06
25
3600
8 × 11.5
100
RNS1C101MDN1††
FP-016RE101M-NS††
240
0.06
21
3900
8 × 11.5
150
RNS1C151MDN1††
FP-016RE151M-NS††
360
0.06
10
5500
10 × 12.5
180
RNS1C181MDN1††
FP-016RE181M-NS††
432
0.08
16
4700
8 × 11.5
330
RNS1C331MDN1††
FP-016RE331M-NS††
792
0.08
10
5500
10 × 12.5
6.3 × 7
15
RNS1D150MDS1††
FP-020RE150M-NS††
50
0.06
63
1700
22
RNS1D220MDS1††
FP-020RE220M-NS††
66
0.06
49
1900
6.3 × 7
33
RNS1D330MDS1††
FP-020RE330M-NS††
99
0.06
49
2200
6.3 × 10
47
RNS1D470MDN1††
FP-020RE470M-NS††
141
0.06
28
3400
8 × 11.5
68
RNS1D680MDN1††
FP-020RE680M-NS††
204
0.06
25
3600
8 × 11.5
100
RNS1D101MDN1††
FP-020RE101M-NS††
300
0.06
15
4500
10 × 12.5
10
RNS1E100MDS1††
FP-025RE100M-NS††
50
0.06
63
1700
6.3 × 7
15
RNS1E150MDS1††
FP-025RE150M-NS††
75
0.06
49
2200
6.3 × 10
22
RNS1E220MDN1††
FP-025RE220M-NS††
110
0.06
28
3400
8 × 11.5
33
RNS1E330MDN1††
FP-025RE330M-NS††
165
0.06
20
3800
10 × 12.5
47
RNS1E470MDN1††
FP-025RE470M-NS††
235
0.06
20
3800
10 × 12.5
100
RNS1E101MDN1††
FP-025RE101M-NS††
500
0.08
15
4500
10 × 12.5
* In case of some doubt about measured values, measure after applying rated voltage for 120 minutes at 105°C.
zPart Number (EX) 16V, 100μF
Nichicon P/N
R
Type
FPCAP P/N
FP
Commodity
Mark
NS
1C
101
M
DN
1
Series Name
Rated
Voltage
Rated
Capacitance
Capacitance
Tolerance
Configuration
Control Code
Lead
Forming
CG: Cut lead (Bulk)
JX: φ6.3x10 2.5mm pitch taping
JT: φ6.3x7, 2.5mm pitch taping
KX: φ8, 3.5mm pitch taping
PX: φ6.3&φ8, 5.0mm pitch taping
PH: φ10, 5.0mm pitch taping
016
RE
101
M
NS
R
Rated Voltage
Classification
Rated
Capacitance
Capacitance
Tolerance
Series Name
Lead
Forming
Control Code
R: Long lead (Bulk)
CG: Cut lead (Bulk)
J : φ6.3x10, 2.5mm pitch taping
JT: φ6.3x7, 2.5mm pitch taping
K : φ8, 3.5mm pitch taping
P : φ6.3&φ8, 5.0mm pitch taping
PH: φ10, 5.0mm pitch taping
NICHICON CORPORATION / FPCAP ELECTRONICS (SUZHOU) CO., LTD.
9
Products / Radial Lead Type
Functional Polymer Aluminum Solid Electrolytic Capacitors
R7 series
Ultra
Low ESR
Lead-free
zFeatures
RoHS
Compliance
By using Functional Polymer cathode, Frequency & Temp.
characteristics are greatly improved.
‘ Low ESR at a high frequency range.
‘ High ripple current capability.
‘ Long life and high reliability.
zApplications
‘ Switching Power Supply and DC/DC Converter.
‘ Back up Power Supplies of CPU(VRM etc.)
‘ Miniature high Power Supply.
zEnvironmental Correspondence
Corresponding to Lead-free, RoHS compliance and Halogen-free.
‘ The Lead-free of terminal plating (Sn)
zSpecifications
Characteristics
R7
- 55 to + 105°C
2.5 to 16V·DC
68 to 1500μF
± 20% (M)
105°C 2000Hrs at rated voltage
Within ± 20% of the value before test
Not to exceed the value specified
Not to exceed 150% of the value specified
0.1% / 1000Hrs. Max (60%CL)
zSize List
R.V (S.V.)
[V]
Cap. [μF]
68
100
150
220
270
330
390
470
560
680
820
1000
1200
1500
10
[φD×L]
2.5
(2.8)
4.0
(4.6)
6.3
(7.2)
8×11.5
8×11.5
10
(11.5)
16
(18.4)
8×11.5
8×11.5
8×11.5
10×12.5
10×12.5
10×12.5
10×12.5
10×12.5
8×11.5
zDimensions
Aluminum Case
Stand off
Wire (Lead free)
P± 0.5
Operating Temp. Range
Rated Voltage Range
Capacitance Range
Capacitance Tolerance
Condition
Capacitance
Endurance
Leakage Current
tan δ
Failure Rate
φD+0.5Max
Items
φd
L+α Max
15Min
4Min
10×12.5
8×11.5
8×11.5
8×11.5
10×12.5
10×12.5
10×12.5
10×12.5
10×12.5
10×12.5
10×12.5
[Unit : mm]
φD×L
8×11.5
φd
0.6
P
3.5
α
1.5
10×12.5
0.6
5.0
1.5
NICHICON CORPORATION / FPCAP ELECTRONICS (SUZHOU) CO., LTD.
zPart number & Specifications
Rated
Voltage
Rated
Capacitance
(V)
(μF, 120Hz)
680
820
1500
560
820
1200
150
220
330
390
680
820
1000
100
220
470
680
68
100
150
270
330
2.5
4.0
6.3
10
16
Part Number
Leakage
Current *
tanδ
ESR
Rated Ripple
Current
Case Size
NICHICON
FPCAP
(μA, 2 min)
(120Hz)
(mΩ, 100kHz)
(mA, r.m.s.)
φD×L(mm)
RR70E681MDN1††
RR70E821MDN1††
RR70E152MDN1††
RR70G561MDN1††
RR70G821MDN1††
RR70G122MDN1††
RR70J151MDN1††
RR70J221MDN1††
RR70J331MDN1††
RR70J391MDN1††
RR70J681MDN1††
RR70J821MDN1††
RR70J102MDN1††
RR71A101MDN1††
RR71A221MDN1††
RR71A471MDN1††
RR71A681MDN1††
RR71C680MDN1††
RR71C101MDN1††
RR71C151MDN1††
RR71C271MDN1††
RR71C331MDN1††
FP-2R5RE681M-R7††
FP-2R5RE821M-R7††
FP-2R5RE152M-R7††
FP-4R0RE561M-R7††
FP-4R0RE821M-R7††
FP-4R0RE122M-R7††
FP-6R3RE151M-R7††
FP-6R3RE221M-R7††
FP-6R3RE331M-R7††
FP-6R3RE391M-R7††
FP-6R3RE681M-R7††
FP-6R3RE821M-R7††
FP-6R3RE102M-R7††
FP-010RE101M-R7††
FP-010RE221M-R7††
FP-010RE471M-R7††
FP-010RE681M-R7††
FP-016RE680M-R7††
FP-016RE101M-R7††
FP-016RE151M-R7††
FP-016RE271M-R7††
FP-016RE331M-R7††
425
513
938
224
328
960
47
69
104
246
428
517
630
50
110
470
1360
54
80
120
648
792
0.08
0.08
0.08
0.08
0.08
0.15
0.07
0.07
0.07
0.08
0.08
0.12
0.12
0.07
0.07
0.08
0.10
0.06
0.06
0.06
0.08
0.08
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
7
5600
5600
6100
5600
6100
6100
5600
5600
6100
5600
6100
6100
6100
5600
6100
6100
6100
5600
5600
6100
6100
6100
8 × 11.5
8 × 11.5
10 × 12.5
8 × 11.5
10 × 12.5
10 × 12.5
8 × 11.5
8 × 11.5
10 × 12.5
8 × 11.5
10 × 12.5
10 × 12.5
10 × 12.5
8 × 11.5
10 × 12.5
10 × 12.5
10 × 12.5
8 × 11.5
8 × 11.5
10 × 12.5
10 × 12.5
10 × 12.5
* In case of some doubt about measured values, measure after applying rated voltage for 120 minutes at 105°C.
zFrequency Characteristics
10000
4.0V 560μF (R7 series)
2.5V 820μF (R7 series)
4.0V 560μF (R7 series)
2.5V 820μF (R7 series)
1000
1000
ESR (mΩ)
Impedance (mΩ)
10000
100
100
10
10
1
1
0.1
1
10
100
Frequency (kHz)
1000
0.1
10000
1
10
100
Frequency (kHz)
1000
10000
zPart Number (EX) 4V, 560μF
Nichicon P/N
R
Type
R7
0G
561
M
DN
1
Series Name
Rated
Voltage
Rated
Capacitance
Capacitance
Tolerance
Configuration
Control Code
Lead
Forming
CG: Cut lead (Bulk)
KX: φ8, 3.5mm pitch taping
PX: φ8, 5.0mm pitch taping
PH: φ10, 5.0mm pitch taping
FPCAP P/N
FP
Commodity
Mark
4R0
RE
561
M
R7
R
Rated Voltage
Classification
Rated
Capacitance
Capacitance
Tolerance
Series Name
Lead
Forming
Control Code
R: Long lead (Bulk)
CG: Cut lead (Bulk)
K : φ8, 3.5mm pitch taping
P : φ8, 5.0mm pitch taping
PH: φ10, 5.0mm pitch taping
NICHICON CORPORATION / FPCAP ELECTRONICS (SUZHOU) CO., LTD.
11
Products / Radial Lead Type
Functional Polymer Aluminum Solid Electrolytic Capacitors
R5 series
Ultra
Low ESR
Lead-free
zFeatures
RoHS
Compliance
By using Functional Polymer cathode, Frequency & Temp.
characteristics are greatly improved.
‘ Low ESR at a high frequency range.
‘ High ripple current capability.
‘ Long life and high reliability.
zApplications
‘ Switching Power Supply and DC/DC Converter.
‘ Back up Power Supplies of CPU(VRM etc.)
‘ Miniature high Power Supply.
zEnvironmental Correspondence
Corresponding to Lead-free, RoHS compliance and Halogen-free.
‘ The Lead-free of terminal plating (Sn)
zSpecifications
Characteristics
R5
Operating Temp. Range
Rated Voltage Range
Capacitance Range
Capacitance Tolerance
Condition
Capacitance
Endurance
Leakage Current
tan δ
Failure Rate
- 55 to + 105°C
2.5 to 6.3V·DC
390 to 1500μF
± 20% (M)
105°C 2000Hrs at rated voltage
Within ± 20% of the value before test
Not to exceed the value specified
Not to exceed 150% of the value specified
0.1% / 1000Hrs. Max (60%CL)
R.V (S.V.)
[V]
Cap. [μF]
390
470
560
680
820
1000
1200
1500
[φD×L]
2.5
(2.8)
4.0
(4.6)
6.3
(7.2)
8×11.5
8×11.5
8×11.5
8×11.5
8×11.5
8×11.5
8×11.5
10×12.5
zDimensions
10×12.5
10×12.5
φD+0.5Max
zSize List
Aluminum Case
Stand off
Wire (Lead free)
P± 0.5
Items
φd
L+α Max
15Min
4Min
10×12.5
10×12.5
[Unit : mm]
12
φD×L
8×11.5
φd
0.6
3.5
P
α
1.5
10×12.5
0.6
5.0
1.5
NICHICON CORPORATION / FPCAP ELECTRONICS (SUZHOU) CO., LTD.
zPart number & Specifications
Rated
Voltage
Rated
Capacitance
(V)
(μF, 120Hz)
560
680
820
2.5
1000
1500
560
820
4.0
1200
390
470
6.3
Leakage
Current *
tanδ
ESR
Rated Ripple
Current
Case Size
(μA, 2 min)
φD×L(mm)
Part Number
NICHICON
FPCAP
RR50E561MDN1††
RR50E681MDN1††
FP-2R5RE561M-R5††
FP-2R5RE681M-R5††
RR50E821MDN1††
RR50E102MDN1††
RR50E152MDN1††
FP-2R5RE821M-R5††
FP-2R5RE102M-R5††
FP-2R5RE152M-R5††
RR50G561MDN1††
RR50G821MDN1††
FP-4R0RE561M-R5††
FP-4R0RE821M-R5††
RR50G122MDN1††
RR50J391MDN1††
FP-4R0RE122M-R5††
FP-6R3RE391M-R5††
FP-6R3RE471M-R5††
680
RR50J471MDN1††
RR50J681MDN1††
820
RR50J821MDN1††
FP-6R3RE681M-R5††
FP-6R3RE821M-R5††
(120Hz)
(mΩ, 100kHz)
(mA, r.m.s.)
350
0.15
5
6630
8 × 11.5
425
0.15
5
6630
8 × 11.5
513
0.15
5
6630
8 × 11.5
625
0.15
5
6630
8 × 11.5
10 × 12.5
938
0.15
5
7220
560
0.15
5
6630
8 × 11.5
820
0.15
5
7220
10 × 12.5
1200
0.15
5
7220
10 × 12.5
614
0.15
5
6630
8 × 11.5
592
0.15
5
6630
8 × 11.5
1071
0.15
5
7220
10 × 12.5
1292
0.15
5
7220
10 × 12.5
* In case of some doubt about measured values, measure after applying rated voltage for 120 minutes at 105°C.
zFrequency Characteristics
10000
10000
4.0V 560μF (R5 series)
1000
1000
ESR ( mΩ )
Impedance ( mΩ )
4.0V 560μF (R5 series)
100
10
100
1
10
1
0.1
1
10
100
1000
Frequency (kHz)
10000
0.1
1
10
100
Frequency (kHz)
1000
10000
zPart Number (EX) 4V, 560μF
Nichicon P/N
R
Type
R5
0G
561
M
DN
1
Series Name
Rated
Voltage
Rated
Capacitance
Capacitance
Tolerance
Configuration
Control Code
Lead
Forming
CG: Cut lead (Bulk)
KX: φ8, 3.5mm pitch taping
PX: φ8, 5.0mm pitch taping
PH: φ10, 5.0mm pitch taping
FPCAP P/N
FP
Commodity
Mark
4R0
RE
561
M
R5
R
Rated Voltage
Classification
Rated
Capacitance
Capacitance
Tolerance
Series Name
Lead
Forming
Control Code
R: Long lead (Bulk)
CG: Cut lead (Bulk)
K : φ8, 3.5mm pitch taping
P : φ8, 5.0mm pitch taping
PH: φ10, 5.0mm pitch taping
NICHICON CORPORATION / FPCAP ELECTRONICS (SUZHOU) CO., LTD.
13
Products / Radial Lead Type
Functional Polymer Aluminum Solid Electrolytic Capacitors
L8 series
zFeatures
Ultra
Low ESR
Large
Capacitance
Low Profile
Lead-free
Endurance
2000/5000hrs
RoHS
Compliance
By using Functional Polymer cathode, Frequency & Temp.
characteristics are greatly improved.
‘ Low ESR at a high frequency range.
‘ High ripple current capability.
‘ Long life and high reliability.
zApplications
‘ Switching Power Supply and DC/DC Converter.
‘ Back up Power Supplies of CPU(VRM etc.)
‘ Miniature high Power Supply.
zEnvironmental Correspondence
Corresponding to Lead-free, RoHS compliance and Halogen-free.
‘ The Lead-free of terminal plating (Sn)
zSpecifications
Characteristics
L8
- 55 to + 105°C
2.5 to 35V·DC
100 to 1500μF
± 20% (M)
105°C 2000/5000Hrs at rated voltage
Within ± 20% of the value before test
Not to exceed the value specified
Not to exceed 150% of the value specified
0.1% / 1000Hrs. Max (60%CL)
zSize List
R.V (S.V.)
[V]
Cap. [μF]
100
180
220
270
330
470
560
680
820
1000
1200
1500
14
[φD×L]
2.5
(2.8)
4.0
(4.6)
8×8
8×8
8×8
8×8
8×8
8×8
8×8
6.3
(7.2)
8×8
8×8
8×8
8×8
8×8
16
(18.4)
35
(40.2)
8×8
8×8
8×8
8×8
8×8
8×8
zDimensions
Aluminum Case
Stand off
Wire (Lead free)
P± 0.5
Operating Temp. Range
Rated Voltage Range
Capacitance Range
Capacitance Tolerance
Condition
Capacitance
Endurance
Leakage Current
tan δ
Failure Rate
φD+0.5Max
Items
φd
L+α Max
15Min
4Min
[Unit : mm]
φD×L
8×8
φd
0.6
P
3.5
NICHICON CORPORATION / FPCAP ELECTRONICS (SUZHOU) CO., LTD.
α
1.0
zPart number & Specifications
Rated
Voltage
Rated
Capacitance
(V)
(μF, 120Hz)
560
** 560
820
2.5
** 820
1000
1200
1500
560
4.0
Rated Ripple
Current
Case Size
(mA, r.m.s.)
φD×L(mm)
NICHICON
FPCAP
RL80E561MDN1††
FP-2R5RE561M-L8††
500
(120Hz) (mΩ, 100kHz)
0.12
6
6100
8×8
RL80E561MDNASQ††
RL80E821MDN1††
FP-2R5RE561M-L8††-5K
FP-2R5RE821M-L8††
500
0.12
6
6100
8×8
513
0.12
6
6100
8×8
RL80E821MDNASQ††
RL80E102MDN1††
FP-2R5RE821M-L8††-5K
FP-2R5RE102M-L8††
513
0.12
6
6100
8×8
625
0.12
6
6100
8×8
RL80E122MDN1††
RL80E152MDN1††
FP-2R5RE122M-L8††
FP-2R5RE152M-L8††
750
0.12
7
6100
8×8
938
0.12
7
6100
8×8
FP-4R0RE561M-L8††
560
0.12
6
6100
8×8
FP-4R0RE561M-L8††-5K
FP-4R0RE821M-L8††
560
0.12
6
6100
8×8
820
0.12
6
6100
8×8
RL80J471MDN1††
RL80J471MDNASQ††
FP-6R3RE471M-L8††
FP-6R3RE471M-L8††-5K
592
0.12
8
5700
8×8
592
0.12
8
5700
8×8
RL80J561MDN1††
FP-6R3RE561M-L8††
706
0.12
8
5700
8×8
RL80J561MDNASQ††
RL80J681MDN1††
FP-6R3RE561M-L8††-5K
FP-6R3RE681M-L8††
706
0.12
8
5700
8×8
857
0.12
8
5700
8×8
RL80J821MDN1††
RL80J102MDN1††
FP-6R3RE821M-L8††
FP-6R3RE102M-L8††
1033
0.12
8
5700
8×8
1260
0.12
9
5700
8×8
FP-016RE101M-L8††
FP-016RE181M-L8††
320
0.12
12
5000
8×8
180
RL81C101MDN1††
RL81C181MDN1††
576
0.12
12
5000
8×8
220
RL81C221MDN1††
FP-016RE221M-L8††
704
0.12
12
5000
8×8
270
FP-016RE271M-L8††
FP-016RE331M-L8††
864
0.12
10
5000
8×8
330
RL81C271MDN1††
RL81C331MDN1††
1056
0.12
12
5000
8×8
100
RL81V101MDN1††
FP-035RE101M-L8††
700
0.12
25
3000
8×8
820
** 470
560
** 560
680
820
1000
100
35
ESR
RL80G561MDN1††
470
16
(μA, 2 min)
tanδ
RL80G561MDNASQ††
RL80G821MDN1††
** 560
6.3
Leakage
Current *
Part Number
* In case of some doubt about measured values, measure after applying rated voltage for 120 minutes at 105°C.
** Endurance 5000hrs product.
zFrequency Characteristics
10000
10000
16V 270μF(L8 series)
1000
ESR (mΩ)
Impedance (mΩ)
16V 270μF(L8 series)
100
10
1000
100
10
1
1
0.1
1
10
100
1000
Frequency (kHz)
10000
0.1
1
10
100
1000
10000
Frequency (kHz)
zPart Number (EX) 6.3V, 560μF, 5000hrs (Endurance)
Nichicon P/N
R
Type
FPCAP P/N
FP
Commodity
Mark
L8
0J
561
M
DN
ASQ
Series Name
Rated
Voltage
Rated
Capacitance
Capacitance
Tolerance
Configuration
Control Code
ASQ
1
: 5000hrs
: 2000hrs
Lead
Forming
CG: Cut lead (Bulk)
KX: φ8, 3.5mm pitch taping
PX: φ8, 5.0mm pitch taping
6R3
RE
561
M
L8
R
-5K
Rated Voltage
Classification
Rated
Capacitance
Capacitance
Tolerance
Series Name
Lead
Forming
Control Code
R: Long lead (Bulk)
CG: Cut lead (Bulk)
K : φ8, 3.5mm pitch taping
P : φ8, 5.0mm pitch taping
-5K
: 5000hrs
Without -5K: 2000hrs
NICHICON CORPORATION / FPCAP ELECTRONICS (SUZHOU) CO., LTD.
15
Products / Radial Lead Type
Functional Polymer Aluminum Solid Electrolytic Capacitors
E5 series
Ultra
Low ESR
Low Profile
Lead-free
zFeatures
Large
Capacitance
RoHS
Compliance
By using Functional Polymer cathode, Frequency & Temp.
characteristics are greatly improved.
‘ Low ESR at a high frequency range.
‘ High ripple current capability.
‘ Long life and high reliability.
zApplications
‘ Switching Power Supply and DC/DC Converter.
‘ Back up Power Supplies of CPU(VRM etc.)
‘ Miniature high Power Supply.
zEnvironmental Correspondence
Corresponding to Lead-free, RoHS compliance and Halogen-free.
‘ The Lead-free of terminal plating (Sn)
zSpecifications
Operating Temp. Range
Rated Voltage Range
Capacitance Range
Capacitance Tolerance
Condition
Capacitance
Endurance
Leakage Current
tan δ
Failure Rate
- 55 to + 105°C
2.5 to 4.0V·DC
560 to 820μF
± 20% (M)
105°C 2000Hrs at rated voltage
Within ± 20% of the value before test
Not to exceed the value specified
Not to exceed 150% of the value specified
0.1% / 1000Hrs. Max (60%CL)
zSize List
R.V (S.V.)
[V]
Cap. [μF]
560
820
[φD×L]
2.5
(2.8)
4.0
(4.6)
8×8
8×8
8×8
zDimensions
Aluminum Case
Stand off
Wire (Lead free)
P± 0.5
Characteristics
E5
φD+0.5Max
Items
φd
L+α Max
15Min
4Min
[Unit : mm]
φD×L
8×8
16
φd
0.6
P
3.5
NICHICON CORPORATION / FPCAP ELECTRONICS (SUZHOU) CO., LTD.
α
1.0
zPart number & Specifications
Rated
Voltage
Rated
Capacitance
(V)
(μF, 120Hz)
2.5
4.0
Part Number
Leakage
Current *
tanδ
ESR
Rated Ripple
Current
Case Size
φD×L(mm)
NICHICON
FPCAP
(μA, 2 min)
(120Hz)
(mΩ, 100kHz)
(mA, r.m.s.)
560
RE50E561MDN1††
FP-2R5RE561M-E5††
500
0.10
5
6300
8×8
820
RE50E821MDN1††
FP-2R5RE821M-E5††
513
0.10
5
6300
8×8
560
RE50G561MDN1††
FP-4R0RE561M-E5††
560
0.10
5
6300
8×8
* In case of some doubt about measured values, measure after applying rated voltage for 120 minutes at 105°C.
zFrequency Characteristics
10000
10000
2.5V 560μF (E5 series)
1000
1000
ESR (mΩ)
Impedance (mΩ)
2.5V 560μF (E5 series)
100
10
100
10
1
1
0.1
1
10
100
Frequency (kHz)
1000
0.1
10000
1
10
100
1000
10000
Frequency (kHz)
zPart Number (EX) 4V, 560μF
Nichicon P/N
R
Type
E5
0G
561
M
DN
1
Series Name
Rated
Voltage
Rated
Capacitance
Capacitance
Tolerance
Configuration
Control Code
Lead
Forming
CG: Cut lead (Bulk)
KX: φ8, 3.5mm pitch taping
PX: φ8, 5.0mm pitch taping
FPCAP P/N
FP
Commodity
Mark
4R0
RE
561
M
E5
R
Rated Voltage
Classification
Rated
Capacitance
Capacitance
Tolerance
Series Name
Lead
Forming
Control Code
R: Long lead (Bulk)
CG: Cut lead (Bulk)
K : φ8, 3.5mm pitch taping
P : φ8, 5.0mm pitch taping
NICHICON CORPORATION / FPCAP ELECTRONICS (SUZHOU) CO., LTD.
17
Products / Radial Lead Type
Functional Polymer Aluminum Solid Electrolytic Capacitors
S8 series
zFeatures
Ultra
Low ESR
Large
Capacitance
Low ESL
Lead-free
By using Functional Polymer cathode, Frequency & Temp.
characteristics are greatly improved.
‘ Low ESR and Low ESL at a high frequency range.
‘ High ripple current capability.
‘ Long life and high reliability.
Endurance
2000/5000hrs
RoHS
Compliance
zApplications
‘ Switching Power Supply and DC/DC Converter.
‘ Back up Power Supplies of CPU(VRM etc.)
‘ Miniature high Power Supply.
zEnvironmental Correspondence
Corresponding to Lead-free, RoHS compliance and Halogen-free.
‘ The Lead-free of terminal plating (Sn)
zSpecifications
Characteristics
S8
- 55 to + 105°C
2.5 to 16V·DC
100 to 1200μF
± 20% (M)
105°C 2000/5000Hrs at rated voltage
Within ± 20% of the value before test
Not to exceed the value specified
Not to exceed 150% of the value specified
0.1% / 1000Hrs. Max (60%CL)
R.V (S.V.)
[V]
2.5
(2.8)
4.0
(4.6)
6.3
(7.2)
16
(18.4)
6.3×8
6.3×8
6.3×8
6.3×8
6.3×8
6.3×8
6.3×8
6.3×8
6.3×8
6.3×8
6.3×8
6.3×8
zDimensions
Aluminum Case
Stand off
Wire (Lead free)
φd
L+α Max
15Min
4Min
[φ6.3×8 (-H)]
Aluminum Case
Wire (Lead free)
φD+0.5Max
Cap. [μF]
100
270
330
470
560
680
820
1200
[φD×L]
P± 0.5
zSize List
P± 0.5
Operating Temp. Range
Rated Voltage Range
Capacitance Range
Capacitance Tolerance
Condition
Capacitance
Endurance
Leakage Current
tan δ
Failure Rate
φD+0.5Max
Items
φd
L+α Max
15Min
4Min
[Unit : mm]
φD×L
6.3×8
18
φd
0.6
P
2.5
NICHICON CORPORATION / FPCAP ELECTRONICS (SUZHOU) CO., LTD.
α
1.0
zPart number & Specifications
Rated
Voltage
Rated
Capacitance
(V)
(μF, 120Hz)
Part Number
330
** 330
470
** 470
2.5
560
** 560
820
4.0
ESR
ESL
(Typ.)
Rated Ripple
Current
Case Size
(μA, 2 min)
φD×L(mm)
NICHICON
FPCAP
(120Hz)
(mΩ, 100kHz)
(nH, 40MHz)
(mA, r.m.s.)
RS80E331MDN1††
FP-2R5RE331M-S8††
500
0.10
7
2
5600
6.3 × 8
RS80E331MDNASQ††
FP-2R5RE331M-S8††-5K
500
0.10
7
2
5600
6.3 × 8
RS80E471MDN1††
FP-2R5RE471M-S8††
500
0.10
7
2
5600
6.3 × 8
RS80E471MDNASQ††
FP-2R5RE471M-S8††-5K
500
0.10
7
2
5600
6.3 × 8
RS80E561MDN1††
FP-2R5RE561M-S8††
500
0.10
7
2
5600
6.3 × 8
RS80E561MDNASQ††
FP-2R5RE561M-S8††-5K
500
0.10
7
2
5600
6.3 × 8
RS80E821MDN1††
FP-2R5RE821M-S8††
512
0.10
7
2
5600
6.3 × 8
RS80E821MDNASQ††
FP-2R5RE821M-S8††-5K
512
0.10
7
2
5600
6.3 × 8
1200
RS80E122MDN1††
FP-2R5RE122M-S8††
750
0.10
7
2
5600
6.3 × 8
560
RS80G561MDN1††
FP-4R0RE561M-S8††
560
0.10
7
2
5000
6.3 × 8
RS80G561MDNASQ††
FP-4R0RE561M-S8††-5K
560
0.10
7
2
5000
6.3 × 8
330
** 330
470
** 470
560
RS80J331MDN1††
FP-6R3RE331M-S8††
519
0.10
8
2
5000
6.3 × 8
RS80J331MDNASQ††
FP-6R3RE331M-S8††-5K
519
0.10
8
2
5000
6.3 × 8
RS80J471MDN1††
FP-6R3RE471M-S8††
740
0.10
8
2
5000
6.3 × 8
RS80J471MDNASQ††
FP-6R3RE471M-S8††-5K
740
0.10
8
2
5000
6.3 × 8
RS80J561MDN1††
FP-6R3RE561M-S8††
882
0.10
8
2
5000
6.3 × 8
RS80J561MDNASQ††
FP-6R3RE561M-S8††-5K
882
0.10
8
2
5000
6.3 × 8
680
RS80J681MCN1††
FP-6R3RE681M-S8††-H
1071
0.10
8
2
4700
6.3 × 8
100
RS81C101MDN1††
FP-016RE101M-S8††
500
0.10
14
2
3800
6.3 × 8
270
RS81C271MDN1††
FP-016RE271M-S8††
1296
0.10
15
2
3800
6.3 × 8
** 560
16
tanδ
** 820
** 560
6.3
Leakage
Current *
* In case of some doubt about measured values, measure after applying rated voltage for 120 minutes at 105°C.
** Endurance 5000hrs product.
zFrequency Characteristics
10000
10000
6.3V 560μF (S8 series)
1000
1000
ESR (mΩ)
Impedance (mΩ)
6.3V 560μF (S8 series)
100
100
10
10
1
1
0.1
1
10
100
Frequency (kHz)
1000
0.1
10000
1
10
100
Frequency (kHz)
1000
10000
zPart Number (EX) 2.5V, 820μF, 5000hrs (Endurance)
Nichicon P/N
R
Type
S8
0E
821
M
DN
ASQ
Series Name
Rated
Voltage
Rated
Capacitance
Capacitance
Tolerance
Configuration
Control Code
ASQ
1
FPCAP P/N
FP
Commodity
Mark
: 5000hrs
: 2000hrs
Lead
Forming
CG: Cut lead (Bulk)
JT: φ6.3, 2.5mm pitch taping
PX: φ6.3x8, 5.0mm pitch taping
2R5
RE
821
M
S8
R
-5K
Rated Voltage
Classification
Rated
Capacitance
Capacitance
Tolerance
Series Name
Lead
Forming
Control Code
R: Long lead (Bulk)
CG: Cut lead (Bulk)
JT: φ6.3x8, 2.5mm pitch taping
P : φ6.3x8, 5.0mm pitch taping
-5K
: 5000hrs
Without -5K: 2000hrs
-H
: Flat rubber
NICHICON CORPORATION / FPCAP ELECTRONICS (SUZHOU) CO., LTD.
19
Products / Radial Lead Type
Functional Polymer Aluminum Solid Electrolytic Capacitors
F8 series
Ultra
Low ESR
Large
Capacitance
Lead-free
zFeatures
By using Functional Polymer cathode, Frequency & Temp.
characteristics are greatly improved.
‘ Low ESR and Low ESL at a high frequency range.
‘ High ripple current capability.
‘ Long life and high reliability.
Low ESL
RoHS
Compliance
zApplications
‘ Switching Power Supply and DC/DC Converter.
‘ Back up Power Supplies of CPU(VRM etc.)
‘ Miniature high Power Supply.
zEnvironmental Correspondence
Corresponding to Lead-free, RoHS compliance and Halogen-free.
‘ The Lead-free of terminal plating (Sn)
zSpecifications
Characteristics
F8
- 55 to + 105°C
2.5 to 6.3V·DC
100 to 560μF
± 20% (M)
105°C 2000Hrs at rated voltage
Within ± 20% of the value before test
Not to exceed the value specified
Not to exceed 150% of the value specified
0.1% / 1000Hrs. Max (60%CL)
zSize List
R.V (S.V.)
[V]
Cap. [μF]
100
270
330
470
560
[φD×L]
2.5
(2.8)
4.0
(4.6)
6.3
(7.2)
5×8
5×8
5×8
5×8
5×8
5×8
zDimensions
Aluminum Case
Stand off
Wire (Lead free)
P± 0.5
Operating Temp. Range
Rated Voltage Range
Capacitance Range
Capacitance Tolerance
Condition
Capacitance
Endurance
Leakage Current
tan δ
Failure Rate
φD+0.5Max
Items
φd
L+α Max
15Min
4Min
[Unit : mm]
φD×L
5×8
20
φd
0.6
P
2.0
NICHICON CORPORATION / FPCAP ELECTRONICS (SUZHOU) CO., LTD.
α
1.0
zPart number & Specifications
Rated
Voltage
Rated
Capacitance
(V)
(μF, 120Hz)
Part Number
Leakage
Current *
tanδ
ESR
ESL
(Typ.)
Rated Ripple
Current
Case Size
NICHICON
FPCAP
(μA, 2 min)
(120Hz)
(mΩ, 100kHz)
(nH, 40MHz)
(mA, r.m.s.)
φD×L(mm)
100
RF80E101MDN1††
FP-2R5RE101M-F8††
500
0.10
7
1.5
4200
5×8
330
RF80E331MDN1††
FP-2R5RE331M-F8††
500
0.10
7
1.5
4200
5×8
470
RF80E471MDN1††
FP-2R5RE471M-F8††
500
0.10
7
1.5
4200
5×8
560
RF80E561MDN1††
FP-2R5RE561M-F8††
500
0.10
7
1.5
4200
5×8
4
330
RF80G331MDN1††
FP-4R0RE331M-F8††
500
0.10
8
1.5
4000
5×8
6.3
270
RF80J271MDN1††
FP-6R3RE271M-F8††
500
0.10
11
1.5
3700
5×8
2.5
* In case of some doubt about measured values, measure after applying rated voltage for 120 minutes at 105°C.
zFrequency Characteristics
10000
10000
2.5V 560μF (F8 series)
1000
1000
ESR (mΩ)
Impedance (mΩ)
2.5V 560μF (F8 series)
100
100
10
10
1
0.1
1
10
100
1000
1
10000
0.1
Frequency (kHz)
1
10
100
1000
10000
Frequency (kHz)
zPart Number (EX) 2.5V, 560μF
Nichicon P/N
R
Type
F8
0E
561
M
DN
1
Series Name
Rated
Voltage
Rated
Capacitance
Capacitance
Tolerance
Configuration
Control Code
Lead
Forming
CG: Cut lead (Bulk)
JT: φ5x8, 2.5mm pitch taping
PX:φ5x8, 5.0mm pitch taping
FPCAP P/N
FP
Commodity
Mark
2R5
RE
561
M
F8
R
Rated Voltage
Classification
Rated
Capacitance
Capacitance
Tolerance
Series Name
Lead
Forming
Control Code
R: Long lead (Bulk)
CG: Cut lead (Bulk)
JT: φ5x8, 2.5mm pitch taping
P : φ5x8, 5.0mm pitch taping
NICHICON CORPORATION / FPCAP ELECTRONICS (SUZHOU) CO., LTD.
21
Products / Radial Lead Type
Functional Polymer Aluminum Solid Electrolytic Capacitors
NU series
zFeatures
Ultra
Low ESR
Large
Capacitance
High Voltage
Lead-free
Endurance
2000/5000hrs
RoHS
Compliance
By using Functional Polymer cathode, Frequency & Temp.
characteristics are greatly improved.
‘ Low ESR at a high frequency range.
‘ High ripple current capability.
‘ Long life and high reliability.
zApplications
‘ Switching Power Supply and DC/DC Converter.
‘ Back up Power Supplies of CPU(VRM etc.)
‘ Miniature high Power Supply.
zEnvironmental Correspondence
Corresponding to Lead-free, RoHS compliance and Halogen-free.
‘ The Lead-free of terminal plating (Sn)
zSpecifications
Characteristics
NU
- 55 to + 105°C
2.5 to 63V·DC
10 to 2700μF
± 20% (M)
105°C 2000/5000Hrs at rated voltage
Within ± 20% of the value before test
Not to exceed the value specified
Not to exceed 150% of the value specified
0.1% / 1000Hrs. Max (60%CL)
Operating Temp. Range
Rated Voltage Range
Capacitance Range
Capacitance Tolerance
Condition
Capacitance
Endurance
Leakage Current
tan δ
Failure Rate
zSize List
R.V (S.V.)
[V]
22
2.5
(2.8)
4.0
(4.6)
6.3
(7.2)
10
(11.5)
16
(18.4)
25
(28.7)
35
(40.2)
50
(57.5)
zDimensions
63
(72.5)
4×5
8×11.5
8×11.5
8×11.5
8×11.5
6.3×10
10×12.5
8×11.5
6.3×10
8×11.5
8×11.5
8×11.5
8×11.5
8×11.5
8×11.5
8×11.5
10×12.5
8×11.5
10×12.5
8×11.5
8×11.5
8×11.5 10×12.5
10×12.5
8×11.5
8×11.5 10×12.5
10×12.5
10×12.5
10×12.5
φD+0.5Max
Cap. [μF]
10
33
39
47
56
68
100
150
180
220
270
330
390
470
680
820
1000
1200
1500
1800
2200
2700
[φD×L]
Aluminum Case
Stand off
Wire (Lead free)
P± 0.5
Items
φd
L+α Max
15Min
8×11.5
8×11.5
10×12.5
10×12.5
4Min
[Unit : mm]
φD×L
4×5
φd
0.45
P
1.5
α
1.0
6.3×10
0.5
2.5
1.0
8×11.5
0.6
3.5
1.5
10×12.5
0.6
5.0
1.5
10×12.5
10×12.5
10×12.5
NICHICON CORPORATION / FPCAP ELECTRONICS (SUZHOU) CO., LTD.
zPart number & Specifications
Rated
Rated
Voltage Capacitance
(V)
Part Number
Leakage
Current *
tanδ
ESR
Rated Ripple
Current
Case Size
(μF, 120Hz)
NICHICON
FPCAP
(μA, 2 min)
(120Hz)
(mΩ, 100kHz)
(mA, r.m.s.)
φD×L(mm)
1500
2700
820
1000
1200
1800
2200
220
470
680
820
1000
1200
1500
10
** 10
1200
100
** 100
180
270
** 270
330
470
** 470
680
33
47
68
180
220
330
390
47
150
39
47
68
33
39
56
RNU0E152MDN1††
RNU0E272MDN1††
RNU0G821MDN1††
RNU0G102MDN1††
RNU0G122MDN1††
RNU0G182MDN1††
RNU0G222MDN1††
RNU0J221MDS1††
RNU0J471MDN1††
RNU0J681MDN1††
RNU0J821MDN1††
RNU0J102MDN1††
RNU0J122MDN1††
RNU0J152MDN1††
RNU1A100MDS1††
RNU1A100MDSASQ††
RNU1A122MDN1††
RNU1C101MDS1††
RNU1C101MDSASQ††
RNU1C181MDN1††
RNU1C271MDN1††
RNU1C271MDNASQ††
RNU1C331MDN1††
RNU1C471MDN1††
RNU1C471MDNASQ††
RNU1C681MDN1††
RNU1E330MDN1††
RNU1E470MDN1††
RNU1E680MDN1††
RNU1E181MDN1††
RNU1E221MDN1††
RNU1E331MDN1††
RNU1E391MDN1††
RNU1V470MDN1††
RNU1V151MDN1††
RNU1H390MDN1††
RNU1H470MDN1††
RNU1H680MDN1††
RNU1J330MDN1††
RNU1J390MDN1††
RNU1J560MDN1††
FP-2R5RE152M-NU††
FP-2R5RE272M-NU††
FP-4R0RE821M-NU††
FP-4R0RE102M-NU††
FP-4R0RE122M-NU††
FP-4R0RE182M-NU††
FP-4R0RE222M-NU††
FP-6R3RE221M-NU††
FP-6R3RE471M-NU††
FP-6R3RE681M-NU††
FP-6R3RE821M-NU††
FP-6R3RE102M-NU††
FP-6R3RE122M-NU††
FP-6R3RE152M-NU††
FP-010RE100M-NU††
FP-010RE100M-NU†† -5K
FP-010RE122M-NU††
FP-016RE101M-NU††
FP-016RE101M-NU†† -5K
FP-016RE181M-NU††
FP-016RE271M-NU††
FP-016RE271M-NU†† -5K
FP-016RE331M-NU††
FP-016RE471M-NU††
FP-016RE471M-NU†† -5K
FP-016RE681M-NU††
FP-025RE330M-NU††
FP-025RE470M-NU††
FP-025RE680M-NU††
FP-025RE181M-NU††
FP-025RE221M-NU††
FP-025RE331M-NU††
FP-025RE391M-NU††
FP-035RE470M-NU††
FP-035RE151M-NU††
FP-050RE390M-NU††
FP-050RE470M-NU††
FP-050RE680M-NU††
FP-063RE330M-NU††
FP-063RE390M-NU††
FP-063RE560M-NU††
938
1350
656
800
960
1440
1760
277
592
857
1033
1260
1512
1890
300
300
2400
320
320
576
864
864
1056
1504
1504
2176
413
588
850
900
1100
1650
1950
329
1050
390
470
680
416
492
706
0.08
0.08
0.08
0.08
0.08
0.08
0.08
0.08
0.08
0.08
0.08
0.08
0.08
0.08
0.12
0.12
0.08
0.08
0.08
0.08
0.08
0.08
0.08
0.08
0.08
0.08
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
7
7
7
7
7
7
7
20
7
7
7
7
9
7
220
220
9
25
25
8
8
8
8
10
10
10
24
24
24
16
16
14
14
24
20
25
24
24
26
25
25
5700
6100
5700
5700
5700
6100
6100
3200
5700
5700
5700
5700
6100
6100
700
700
6200
2820
2820
5700
5000
5000
6100
6100
6100
6100
3600
3600
3600
4650
4650
5000
5000
3600
3800
2400
2700
2700
2300
2600
2600
8 × 11.5
10 × 12.5
8 × 11.5
8 × 11.5
8 × 11.5
10 × 12.5
10 × 12.5
6.3 × 10
8 × 11.5
8 × 11.5
8 × 11.5
8 × 11.5
8 × 11.5
10 × 12.5
4×5
4×5
10 × 12.5
6.3 × 10
6.3 × 10
8 × 11.5
8 × 11.5
8 × 11.5
8 × 11.5
10 × 12.5
10 × 12.5
10 × 12.5
8 × 11.5
8 × 11.5
8 × 11.5
8 × 11.5
8 × 11.5
10 × 12.5
10 × 12.5
8 × 11.5
10 × 12.5
8 × 11.5
10 × 12.5
10 × 12.5
8 × 11.5
10 × 12.5
10 × 12.5
2.5
4.0
6.3
10
16
25
35
50
63
* In case of some doubt about measured values, measure after applying rated voltage for 120 minutes at 105°C.
** Endurance 5000hrs product.
zPart Number (EX) 16V, 270μF, 5000hrs (Endurance)
Nichicon P/N
R
Type
FPCAP P/N
FP
Commodity
Mark
NU
1C
271
M
DN
ASQ
Series Name
Rated
Voltage
Rated
Capacitance
Capacitance
Tolerance
Configuration
Control Code
ASQ
1
: 5000hrs
: 2000hrs
Lead
Forming
CG: Cut lead (Bulk)
, JX: φ6.3x10 2.5mm pitch taping
KX: φ8, 3.5mm pitch taping, PX: φ6.3&φ8, 5.0mm pitch taping
PH: φ10, 5.0mm pitch taping
016
RE
271
M
NU
R
-5K
Rated Voltage
Classification
Rated
Capacitance
Capacitance
Tolerance
Series Name
Lead
Forming
Control Code
R: Long lead (Bulk)
, CG: Cut lead (Bulk)
J : φ6.3x10, 2.5mm pitch taping , K : φ8, 3.5mm pitch taping
P : φ6.3&φ8, 5.0mm pitch taping ,PH: φ10, 5.0mm pitch taping
-5K
: 5000hrs
Without -5K: 2000hrs
NICHICON CORPORATION / FPCAP ELECTRONICS (SUZHOU) CO., LTD.
23
Products / Radial Lead Type
Functional Polymer Aluminum Solid Electrolytic Capacitors
NE
series
zFeatures
Ultra
Low ESR
Ultra Large
Capacitance
Lead free
RoHS
Compliance
By using Functional Polymer cathode, Frequency & Temp.
characteristics are greatly improved.
‘ Low ESR at a high frequency range.
‘ High ripple current capability.
‘ Long life and high reliability.
zApplications
‘ Switching Power Supply and DC/DC Converter.
‘ Back up Power Supplies of CPU(VRM etc.)
‘ Miniature high Power Supply.
zEnvironmental Correspondence
Corresponding to Lead-free, RoHS compliance and Halogen-free.
‘ The Lead-free of terminal plating (Sn)
zSpecifications
Characteristics
Items
NE
Operating Temp. Range
Rated Voltage Range
Capacitance Range
Capacitance Tolerance
Condition
Capacitance
Endurance
Leakage Current
tan δ
Failure Rate
-55 to +105°C
2.5 to 16V·DC
100 to 1200μF
± 20% (M)
105°C 2000Hrs at rated voltage
Within ± 20% of the value before test
Not to exceed the value specified
Not to exceed 150% of the value specified
0.1% / 1000Hrs. Max (60%CL)
Cap. [μF]
100
220
270
470
680
820
1000
1200
24
[φD×L]
2.5
(2.8)
6.3
(7.2)
10
(11.5)
5×10
6.3×10
5×8
8×11.5
8×6
10×12.5
10×12.5
8×9
zDimensions
16
(18.4)
Aluminum Case
Stand off
Wire (Lead free)
P± 0.5
R.V (S.V.)
[V]
φD+0.5Max
zSize List
φd
L+α Max
15Min
4Min
[Unit : mm]
φD×L
5×8
5×10
6.3×10
8×6
8×9
8×11.5
10×12.5
φd
0.5
0.5
0.5
0.6
0.6
0.6
0.6
P
2.0
2.0
2.5
3.5
3.5
3.5
5.0
NICHICON CORPORATION / FPCAP ELECTRONICS (SUZHOU) CO., LTD.
α
1.0
1.0
1.0
1.0
1.0
1.5
1.5
zPart number & Specifications
Rated
Voltage
Rated
Capacitance
(V)
(μF, 120Hz)
2.5
6.3
10
16
Part Number
Leakage
Current *
tanδ
ESR
Rated Ripple
Current
Case Size
(μA, 2 min)
φD×L(mm)
NICHICON
FPCAP
(120Hz)
(mΩ, 100kHz)
(mA, r.m.s.)
680
RNE0E681MDN1††
FP-2R5RE681M-NE††
500
0.10
8
4900
8×6
270
RNE0J271MDS1††
FP-6R3RE271M-NE††
500
0.10
12
3600
5×8
1200
RNE0J122MDN1††
FP-6R3RE122M-NE††
1512
0.08
10
5700
8×9
220
RNE1A221MDS1††
FP-010RE221M-NE††
440
0.08
30
2500
6.3 × 10
100
RNE1C101MDS1††
FP-016RE101M-NE††
320
0.08
35
2300
5 × 10
470
RNE1C471MDN1††
FP-016RE471M-NE††
1504
0.08
10
5400
8 × 11.5
820
RNE1C821MDN1††
FP-016RE821M-NE††
2624
0.08
11
5600
10 × 12.5
1000
RNE1C102MDN1††
FP-016RE102M-NE††
3200
0.08
10
6100
10 × 12.5
* In case of some doubt about measured values, measure after applying rated voltage for 120 minutes at 105°C.
zFrequency Characteristics
10000
10000
16V 470μF (NE series)
1000
1000
ESR (mΩ)
Impedance (mΩ)
16V 470μF (NE series)
100
100
10
10
1
1
0.1
1
10
100
1000
10000
0.1
Frequency (kHz)
1
10
100
1000
10000
Frequency (kHz)
zPart Number (EX) 16V, 470μF (Endurance)
Nichicon P/N
R
Type
NE
1C
471
M
DN
1
Series Name
Rated
Voltage
Rated
Capacitance
Capacitance
Tolerance
Configuration
Control Code
Lead
Forming
CG: Cut lead (Bulk)
JT: φ5x8, 2.5mm pitch taping
JX: φ5x10, φ6.3x10, 2.5mm pitch taping
KX: φ8, 3.5mm pitch taping
PX: φ5&φ6.3&φ8, 5.0mm pitch taping
PH: φ10, 5.0mm pitch taping
FPCAP P/N
FP
Commodity
Mark
016
RE
471
M
NE
R
Rated Voltage
Classification
Rated
Capacitance
Capacitance
Tolerance
Series Name
Lead
Forming
Control Code
R: Long lead (Bulk)
CG: Cut lead (Bulk)
JT: φ5x8, 2.5mm pitch taping
J : φ5x10, φ6.3x10, 2.5mm pitch taping
K : φ8, 3.5mm pitch taping
P : φ5&φ6.3&φ8, 5.0mm pitch taping
PH: φ10, 5.0mm pitch taping
NICHICON CORPORATION / FPCAP ELECTRONICS (SUZHOU) CO., LTD.
25
Products / Radial Lead Type
Functional Polymer Aluminum Solid Electrolytic Capacitors
S6 series
Low ESR
Low Profile
RoHS
Compliance
Lead-free
zFeatures
Large
Capacitance
By using Functional Polymer cathode, Frequency & Temp.
characteristics are greatly improved.
‘ Low ESR at a high frequency range.
‘ High ripple current capability.
‘ Long life and high reliability.
zApplications
‘ Switching Power Supply and DC/DC Converter.
‘ Back up Power Supplies of CPU(VRM etc.)
‘ Miniature high Power Supply.
zEnvironmental Correspondence
Corresponding to Lead-free, RoHS compliance and Halogen-free.
‘ The Lead-free of terminal plating (Sn)
zSpecifications
-55 to +105°C
2.5 to 25 V·DC
33 to 560 μF
±20% (M)
105°C 2000Hrs at rated voltage
Within ±20% of the value before test
Not to exceed the value specified
Not to exceed 150% of the value specified
0.1% / 1000Hrs. Max (60%CL)
zSize List
R.V (S.V.)
[V]
Cap. [μF]
[φD×L]
2.5
(2.8)
10
(11.5)
16
(18.4)
33
6.3×5
100
6.3×6
150
[φ6.3×6]
6.3×5
6.3×5
Aluminum Case
Stand off
Wire (Lead free)
φd
L+α Max
15Min
Wire (Lead free)
φd
L+α Max
26
4Min
[φ6.3×5 / φ6.3×6 (-H)]
Aluminum Case
φD+0.5Max
560
25
(28.7)
zDimensions
P± 0.5
Operating Temp. Range
Rated Voltage Range
Capacitance Range
Capacitance Tolerance
Condition
Capacitance
Endurance
Leakage Current
tan δ
Failure Rate
P± 0.5
Characteristics
S6
φD+0.5Max
Items
15Min
P
4Min
[Unit : mm]
φD×L
6.3×5
φd
0.5
2.5
α
1.0
6.3×6
0.45
2.5
1.0
NICHICON CORPORATION / FPCAP ELECTRONICS (SUZHOU) CO., LTD.
zPart number & Specifications
Rated
Voltage
Rated
Capacitance
(V)
(μF, 120Hz)
Part Number
Leakage
Current *
tanδ
ESR
Rated Ripple
Current
Case Size
NICHICON
FPCAP
(μA, 2 min)
(120Hz)
(mΩ, 100kHz)
(mA, r.m.s.)
φD×L(mm)
2.5
560
RS60E561MCN1††
FP-2R5RE561M-S6††
700
0.12
13
3600
6.3 × 5
10
150
RS61A151MCN1††
FP-010RE151M-S6††
450
0.10
25
2500
6.3 × 5
100
RS61C101MDS1††
FP-016RE101M-S6††
500
0.10
24
2490
6.3 × 6
100
RS61C101MCS1††
FP-016RE101M-S6††-H
500
0.10
24
2490
6.3 × 6
33
RS61E330MCN1††
FP-025RE330M-S6††
165
0.10
60
1700
6.3 × 5
16
25
* In case of some doubt about measured values, measure after applying rated voltage for 120 minutes at 105°C.
zFrequency Characteristics
10000
100000
16V 100μF (S6 series)
10000
1000
ESR (mΩ)
Impedance (mΩ)
16V 100μF (S6 series)
1000
100
100
10
10
1
1
0.1
1
10
100
1000
10000
0.1
Frequency (kHz)
1
10
100
Frequency (kHz)
1000
10000
zPart Number (EX) 16V, 100μF Flat rubber Type (-H)
Nichicon P/N
R
Type
S6
1C
101
M
CS
1
Series Name
Rated
Voltage
Rated
Capacitance
Capacitance
Tolerance
Configuration
Control Code
Lead
Forming
CG: Cut lead (Bulk)
JT : φ6.3x5/6, 2.5mm pitch taping
PX : φ6.3 5.0mm pitch taping
FPCAP P/N
FP
Commodity
Mark
016
RE
101
M
S6
R
-H
Rated Voltage
Classification
Rated
Capacitance
Capacitance
Tolerance
Series Name
Lead
Forming
Control Code
R: Long lead (Bulk)
CG: Cut lead (Bulk)
JT: φ6.3x5/6, 2.5mm pitch taping
P : φ6.3, 5.0mm pitch taping
-H : Flat rubber
NICHICON CORPORATION / FPCAP ELECTRONICS (SUZHOU) CO., LTD.
27
Products / Radial Lead Type
Functional Polymer Aluminum Solid Electrolytic Capacitors
HT series
Low ESR
Guarantee
125ºC
Lead-free
zFeatures
By using Functional Polymer cathode, Frequency & Temp.
characteristics are greatly improved.
‘ Low ESR at a high frequency range.
‘ High ripple current capability.
‘ Guaranteed at 125 degrees and high reliability.
Large
Capacitance
RoHS
Compliance
zApplications
‘ Switching Power Supply and DC/DC Converter.
‘ Back up Power Supplies of CPU(VRM etc.)
‘ Miniature high Power Supply.
zEnvironmental Correspondence
Corresponding to Lead-free, RoHS compliance and Halogen-free.
‘ The Lead-free of terminal plating (Sn)
zSpecifications
Characteristics
HT
- 55 to + 125°C
6.3 to 20V·DC
150 to 820μF
± 20% (M)
125°C 1000Hrs at rated voltage
Within ± 20% of the value before test
Not to exceed the value specified
Not to exceed 150% of the value specified
0.5% / 1000Hrs. Max (60%CL)
zSize List
R.V (S.V.)
[V]
Cap. [μF]
150
220
270
330
390
560
680
820
28
[φD×L]
6.3
(7.2)
10
(11.5)
16
(18.4)
20
(23)
10×12.5
8×11.5
8×11.5
8×11.5
10×12.5
10×12.5
10×12.5
zDimensions
Aluminum Case
Stand off
Wire (Lead free)
P± 0.5
Operating Temp. Range
Rated Voltage Range
Capacitance Range
Capacitance Tolerance
Condition
Capacitance
Endurance
Leakage Current
tan δ
Failure Rate
φD+0.5Max
Items
φd
L+α Max
15Min
10×12.5
10×12.5
4Min
[Unit : mm]
φD×L
8×11.5
φd
0.6
3.5
P
α
1.5
10×12.5
0.6
5.0
1.5
NICHICON CORPORATION / FPCAP ELECTRONICS (SUZHOU) CO., LTD.
zPart number & Specifications
Rated
Voltage
Rated
Capacitance
(V)
(μF, 120Hz)
6.3
10
16
20
Leakage
Current *1
Part Number
tanδ
(μA, 2 min)
(120Hz)
Rated Ripple Current
ESR
2
2
* 105ºC
or less
(mΩ, 100kHz)
* 105ºC
to 125ºC
Case Size
NICHICON
FPCAP
680
RHT0J681MDN1††
FP-6R3RE681M-HT††
857
0.12
12
5450
1740
10 x 12.5
820
RHT0J821MDN1††
FP-6R3RE821M-HT††
1033
0.12
12
5450
1740
10 × 12.5
φD×L(mm)
220
RHT1A221MDN1††
FP-010RE221M-HT††
440
0.12
17
3950
1260
8 × 11.5
330
RHT1A331MDN1††
FP-010RE331M-HT††
660
0.12
17
3950
1260
8 × 11.5
390
RHT1A391MDN1††
FP-010RE391M-HT††
780
0.12
16
3950
1260
8 × 11.5
560
RHT1A561MDN1††
FP-010RE561M-HT††
1120
0.12
13
5250
1680
10 × 12.5
270
RHT1C271MDN1††
FP-016RE271M-HT††
864
0.12
16
4750
1520
10 × 12.5
330
RHT1C331MDN1††
FP-016RE331M-HT††
1056
0.12
16
4750
1520
10 × 12.5
150
RHT1D151MDN1††
FP-020RE151M-HT††
600
0.12
20
4350
1390
10 × 12.5
*1: In case of some doubt about measured values, measure after applying rated voltage for 120 minutes at 105°C.
*2: At ambient temperature
zFrequency Characteristics
10000
10000
16V 330μF (HT series)
1000
1000
ESR (mΩ)
Impedance (mΩ)
16V 330μF (HT series)
100
10
100
10
1
1
0.1
1
10
100
1000
0.1
10000
1
10
Frequency (kHz)
100
1000
10000
Frequency (kHz)
zPart Number (EX) 16V, 330μF
Nichicon P/N
R
Type
FPCAP P/N
FP
Commodity
Mark
HT
1C
331
M
DN
1
Series Name
Rated
Voltage
Rated
Capacitance
Capacitance
Tolerance
Configuration
Control Code
Lead
Forming
CG: Cut lead (Bulk)
KX: φ8, 3.5mm pitch taping
PX: φ8, 5.0mm pitch taping
PH: φ10, 5.0mm pitch taping
016
RE
331
M
HT
R
Rated Voltage
Classification
Rated
Capacitance
Capacitance
Tolerance
Series Name
Lead
Forming
Control Code
R: Long lead (Bulk)
CG: Cut lead (Bulk)
K : φ8, 3.5mm pitch taping
P : φ8, 5.0mm pitch taping
PH: φ10, 5.0mm pitch taping
NICHICON CORPORATION / FPCAP ELECTRONICS (SUZHOU) CO., LTD.
29
Products / SMD Type
Functional Polymer Aluminum Solid Electrolytic Capacitors
PS & PA series
Low ESR
SMD
zFeatures
High Voltage
RoHS
Compliance
Lead-free
By using Functional Polymer cathode, Frequency & Temp.
characteristics are greatly improved.
‘ Low ESR at a high frequency range.
‘ High ripple current capability.
‘ Long life and high reliability.
zApplications
‘ Switching Power Supply and DC/DC Converter.
‘ Back up Power Supplies of CPU(VRM etc.)
‘ Miniature high Power Supply.
zEnvironmental Correspondence
zRecommended land pattern
Corresponding to Lead-free, RoHS compliance and Halogen-free.
‘ The Lead-free of terminal plating (Sn)
zSpecifications
b
Operating temp. range
Rated voltage range
Capacitance range
Capacitance tolerance
-55 to +105°C
2.5 to 63V·DC
8.2 to 1500μF
Test condition
Capacitance
Endurance Leakage current
ESR
tan δ
Failure Rate
105°C, rated voltage 2000Hrs.
Within ±20% of initial value before test
Not to exceed the initial specified value
Not to exceed 150% of initial specified value
Not to exceed 150% of initial specified value
0.5% / 1000Hrs. Max (60%CL)
4.0
(4.6)
6.3
(7.2)
[φD×L]
10
(11.5)
16
(18.4)
Cap. [μF]
8.2
12
22
33
25
(28.7)
50
(57.5)
63
(72.5)
8×6.7
6.3×5.7
8×6.7
10×7.7
6.3×5.7
8×6.7
10×7.7
8×11.7
6.3×5.7
(6.3×5.7)
39
47
56
82
100
120
150
180
6.3×5.7
6.3×5.7
6.3×5.7
220
8×6.7
6.3×5.7
8×6.7
8×6.7
8×6.7
270
330
8×6.7
10×7.7
470
10×7.7
8×11.7
(8×11.7)
8×11.7
560
680
820
1000
1200
1500
8×11.7
8×11.7
10×7.7
8×11.7
(10×7.7)
10×7.7
8×11.7
8×11.7
(10×7.7)
8×11.7
10×12.4
c
2.1
3.5
1.6
8
2.8
4.2
1.9
10
4.3
4.4
1.9
zDimensions
W ± 0.2
0.2 Max
P
8×11.7
L ± 0.3
8×11.7
8×6.7
8×6.7
10×7.7
b
C ± 0.2
[V]
2.5
(2.8)
) : PA series
a
H ± 0.2
(
b
[Unit: mm]
φD
6.3
±20% (M)
R.V. (S.V.)
a
φD ± 0.5
zSize List
30
c
Characteristic
PS, PA
Items
R
10×12.4
10×12.4
8×11.7
[Unit: mm]
φD×L
6.3×5.7
W
H
C
R
P
6.5
6.5
7.2
0.5 to 0.9
2.1
8×6.7
8.3
8.3
9.0
0.8 to 1.1
3.2
8×11.7
8.3
8.3
9.0
0.8 to 1.1
3.2
10×7.7
10.3
10.3
11.0
0.8 to 1.1
4.6
10×12.4
10.3
10.3
11.0
0.8 to 1.1
4.6
10×12.4
10×12.4
10×12.4
10×12.4
10×12.4
10×12.4
NICHICON CORPORATION / FPCAP ELECTRONICS (SUZHOU) CO., LTD.
zPart number & Specifications
Rated
Voltage
Rated
Capacitance
(V)
(μF, 120Hz)
680
1500
100
220
330
470
560
560
1200
82
150
180
330
470
560
680
820
1000
47
56
120
270
330
330
560
39
39
56
82
100
150
180
220
220
270
330
22
100
12
22
33
39
47
82
8.2
12
22
33
56
2.5
4.0
6.3
10
16
25
50
63
Part Number
Leakage
Current *
tanδ
ESR
Rated Ripple
Current
Case Size
NICHICON
FPCAP
(μA, 2 min)
(120Hz)
(mΩ, 100kHz)
(mA, r.m.s.)
φD×L(mm)
RPS0E681MCN1GS
RPS0E152MCN1GS
RPS0G101MCN1GS
RPS0G221MCN1GS
RPS0G331MCN1GS
RPS0G471MCN1GS
RPS0G561MCN1GS
RPA0G561MCN1GS
RPS0G122MCN1GS
RPS0J820MCN1GS
RPS0J151MCN1GS
RPS0J181MCN1GS
RPS0J331MCN1GS
RPS0J471MCN1GS
RPS0J561MCN1GS
RPS0J681MCN1GS
RPS0J821MCN1GS
RPS0J102MCN1GS
RPS1A470MCN1GS
RPS1A560MCN1GS
RPS1A121MCN1GS
RPS1A271MCN1GS
RPS1A331MCN1GS
RPA1A331MCN1GS
RPS1A561MCN1GS
RPS1C390MCN1GS
RPA1C390MCN1GS
RPS1C560MCN1GS
RPS1C820MCN1GS
RPS1C101MCN1GS
RPS1C151MCN1GS
RPS1C181MCN1GS
RPS1C221MCN1GS
RPA1C221MCN1GS
RPS1C271MCN1GS
RPS1C331MCN1GS
RPS1E220MCN1GS
RPS1E101MCN1GS
RPS1H120MCN1GS
RPS1H220MCN1GS
RPS1H330MCN1GS
RPS1H390MCN1GS
RPS1H470MCN1GS
RPS1H820MCN1GS
RPS1J8R2MCN1GS
RPS1J120MCN1GS
RPS1J220MCN1GS
RPS1J330MCN1GS
RPS1J560MCN1GS
FP-2R5ME681M-PSR
FP-2R5ME152M-PSR
FP-4R0ME101M-PSR
FP-4R0ME221M-PSR
FP-4R0ME331M-PSR
FP-4R0ME471M-PSR
FP-4R0ME561M-PSR
FP-4R0ME561M-PAR
FP-4R0ME122M-PSR
FP-6R3ME820M-PSR
FP-6R3ME151M-PSR
FP-6R3ME181M-PSR
FP-6R3ME331M-PSR
FP-6R3ME471M-PSR
FP-6R3ME561M-PSR
FP-6R3ME681M-PSR
FP-6R3ME821M-PSR
FP-6R3ME102M-PSR
FP-010ME470M-PSR
FP-010ME560M-PSR
FP-010ME121M-PSR
FP-010ME271M-PSR
FP-010ME331M-PSR
FP-010ME331M-PAR
FP-010ME561M-PSR
FP-016ME390M-PSR
FP-016ME390M-PAR
FP-016ME560M-PSR
FP-016ME820M-PSR
FP-016ME101M-PSR
FP-016ME151M-PSR
FP-016ME181M-PSR
FP-016ME221M-PSR
FP-016ME221M-PAR
FP-016ME271M-PSR
FP-016ME331M-PSR
FP-025ME220M-PSR
FP-025ME101M-PSR
FP-050ME120M-PSR
FP-050ME220M-PSR
FP-050ME330M-PSR
FP-050ME390M-PSR
FP-050ME470M-PSR
FP-050ME820M-PSR
FP-063ME8R2M-PSR
FP-063ME120M-PSR
FP-063ME220M-PSR
FP-063ME330M-PSR
FP-063ME560M-PSR
425
938
80
176
264
376
448
448
960
103
189
227
416
592
706
643
775
945
94
112
240
540
660
660
840
125
125
179
262
320
480
576
704
704
864
792
275
500
120
220
330
390
470
820
103
151
277
416
706
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.15
0.15
0.15
0.15
0.15
0.12
0.12
0.12
0.12
0.15
0.12
0.15
0.10
0.10
0.10
0.10
0.10
0.10
0.12
0.12
0.10
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.15
0.15
0.15
0.12
0.12
0.12
0.15
0.15
13
10
35
30
30
22
13
9
12
35
30
30
22
15
14
13
12
12
40
40
30
25
17
20
13
45
24
40
40
30
30
20
20
22
14
16
50
24
40
37
32
26
26
23
41
38
33
27
24
4500
5500
2200
2700
2700
3800
4500
5400
5500
2200
2600
2600
3600
4300
4400
5200
5500
5500
2100
2100
2600
3500
4000
3600
5300
2000
2500
2300
2300
3200
3200
3700
3700
3450
4400
4800
1800
3320
1250
1550
1950
2300
2300
2800
1200
1500
1900
2250
2700
8 × 11.7
10 × 12.4
6.3 × 5.7
8 × 6.7
8 × 6.7
10 × 7.7
8 × 11.7
8 × 11.7
10 × 12.4
6.3 × 5.7
8 × 6.7
8 × 6.7
10 × 7.7
8 × 11.7
8 × 11.7
10 × 12.4
10 × 12.4
10 × 12.4
6.3 × 5.7
6.3 × 5.7
8 × 6.7
10 × 7.7
8 × 11.7
10 × 7.7
10 × 12.4
6.3 × 5.7
6.3 × 5.7
8 × 6.7
8 × 6.7
10 × 7.7
10 × 7.7
8 × 11.7
8 × 11.7
10 × 7.7
8 × 11.7
10 × 12.4
8 × 6.7
8 × 11.7
6.3 × 5.7
8 × 6.7
10 × 7.7
8 × 11.7
8 × 11.7
10 × 12.4
6.3 × 5.7
8 × 6.7
10 × 7.7
8 × 11.7
10 × 12.4
* In case of some doubt about measured values, measure after applying rated voltage for 120 minutes at 105°C.
zPart Number (EX) 4V, 1200μF, PS series
Nichicon P/N
R
Type
FPCAP P/N
FP
Commodity
Mark
PS
0G
122
M
CN
1
GS
Series Name
Rated
Voltage
Rated
Capacitance
Capacitance
Tolerance
Configuration
Control Code
Taping
Code
4R0
ME
122
M
PS
R
Rated Voltage
Classification
Rated
Capacitance
Capacitance
Tolerance
Series Name
Taping
Code
NICHICON CORPORATION / FPCAP ELECTRONICS (SUZHOU) CO., LTD.
Control Code
31
Products / SMD Type
Functional Polymer Aluminum Solid Electrolytic Capacitors
HS & HA series
zFeatures
Large
Capacitance
Low ESR
φ8
SMD
Lead-free
RoHS
Compliance
By using Functional Polymer cathode, Frequency & Temp.
characteristics are greatly improved.
‘ Low ESR at a high frequency range.
‘ High ripple current capability.
‘ Long life and high reliability.
zApplications
‘ Switching Power Supply and DC/DC Converter.
‘ Back up Power Supplies of CPU(VRM etc.)
‘ Miniature high Power Supply.
zEnvironmental Correspondence
Corresponding to Lead-free, RoHS compliance and Halogen-free.
‘ The Lead-free of terminal plating (Sn)
zRecommended land pattern
zSpecifications
c
Characteristic
HS, HA
b
-55 to +105°C
2.5 to 35V·DC
100 to 1500μF
Test condition
Capacitance
Endurance Leakage current
ESR
tan δ
Failure Rate
105°C, rated voltage 2000Hrs.
Within ±20% of initial value before test
Not to exceed the initial specified value
Not to exceed 150% of initial specified value
Not to exceed 150% of initial specified value
0.5% / 1000Hrs. Max (60%CL)
HA
HS
6.3
(7.2)
HA
HS
HA
10
(11.5)
16
(18.4)
20
(23.0)
HS
HA
HS
100
8×6.7
(25)
150
270
330
8×6.7
(18)
390
470
8×6.7
(16)
560
680
820
8×11.7
(9)
1000
1200
1500
32
8×11.7
(9)
8×6.7
(8)
8×6.7
(8)
8×7.7
(8)
8×6.7
(8)
8×7.7
(8)
8×11.7
(10)
8×11.7
(10)
8×6.7
(9)
8×6.7
(9)
8×6.7
(9)
8×7.7
(9)
8×6.7
(22)
8×6.7
(22)
25
(28.7)
HS
35
(40.2)
HS
8×8.7
(25)
8×8.7
(25)
b
c
2.8
4.2
1.9
zDimensions
W ± 0.2
0.2 Max
P
L ± 0.3
8×7.7
(19)
8×11.7
(14)
C ± 0.2
HS
4.0
(4.6)
a
φD ± 0.5
Cap. [μF]
[φD×L (mΩ)]
2.5
(2.8)
b
[Unit: mm]
φD
8
±20% (M)
zSize (ESR) List
R.V. (S.V.)
[V]
a
H ± 0.2
Items
Operating temp. range
Rated voltage range
Capacitance range
Capacitance tolerance
R
[Unit: mm]
φD×L
8×6.7
W
H
C
R
P
8.3
8.3
9.0
0.8 to 1.1
3.2
8×7.7
8.3
8.3
9.0
0.8 to 1.1
3.2
8×8.7
8.3
8.3
9.0
0.8 to 1.1
3.2
8×11.7
8.3
8.3
9.0
0.8 to 1.1
3.2
8×11.7
(9)
8×11.7
(12)
NICHICON CORPORATION / FPCAP ELECTRONICS (SUZHOU) CO., LTD.
zPart number & Specifications
Rated
Voltage
Rated
Capacitance
(V)
(μF, 120Hz)
2.5
4.0
6.3
Part Number
Leakage
Current *
tanδ
ESR
Rated Ripple
Current
Case Size
(μA, 2 min)
(120Hz)
(mΩ, 100kHz)
(mA, r.m.s.)
φD×L(mm)
NICHICON
FPCAP
680
RHA0E681MCN1GS
FP-2R5ME681M-HAR
700
0.12
8
5000
8 × 6.7
820
RHS0E821MCN1GS
FP-2R5ME821M-HSR
700
0.12
9
5400
8 × 11.7
820
RHA0E821MCN1GS
FP-2R5ME821M-HAR
700
0.12
8
5000
8 × 6.7
1000
RHA0E102MCN1GS
FP-2R5ME102M-HAR
750
0.12
8
5000
8 × 7.7
1500
RHS0E152MCN1GS
FP-2R5ME152M-HSR
1125
0.12
9
5400
8 × 11.7
560
RHS0G561MCN1GS
FP-4R0ME561M-HSR
700
0.12
16
3200
8 × 6.7
560
RHA0G561MCN1GS
FP-4R0ME561M-HAR
700
0.12
8
5000
8 × 6.7
680
RHA0G681MCN1GS
FP-4R0ME681M-HAR
816
0.12
8
5000
8 × 7.7
1200
RHS0G122MCN1GS
FP-4R0ME122M-HSR
1440
0.12
9
5400
8 × 11.7
1500
RHS0G152MCN1GS
FP-4R0ME152M-HSR
1800
0.12
12
4700
8 × 11.7
330
RHA0J331MCN1GS
FP-6R3ME331M-HAR
700
0.12
9
4500
8 × 6.7
390
RHS0J391MCN1GS
FP-6R3ME391M-HSR
737
0.12
18
3200
8 × 6.7
390
RHA0J391MCN1GS
FP-6R3ME391M-HAR
737
0.12
9
4500
8 × 6.7
470
RHA0J471MCN1GS
FP-6R3ME471M-HAR
888
0.12
9
4500
8 × 6.7
560
RHA0J561MCN1GS
FP-6R3ME561M-HAR
1058
0.12
9
4500
8 × 7.7
820
RHS0J821MCN1GS
FP-6R3ME821M-HSR
1550
0.12
10
5150
8 × 11.7
1000
RHS0J102MCN1GS
FP-6R3ME102M-HSR
1890
0.12
10
5150
8 × 11.7
150
RHS1A151MCN1GS
FP-010ME151M-HSR
700
0.12
25
3000
8 × 6.7
330
RHS1A331MCN1GS
FP-010ME331M-HSR
660
0.12
19
3390
8 × 7.7
150
RHA1C151MCN1GS
FP-016ME151M-HAR
700
0.12
22
3220
8 × 6.7
270
RHA1C271MCN1GS
FP-016ME271M-HAR
864
0.12
22
3300
8 × 6.7
20
390
RHS1D391MCN1GS
FP-020ME391M-HSR
1560
0.12
14
4950
8 × 11.7
25
100
RHS1E101MCN1GS
FP-025ME101M-HSR
700
0.12
18
4000
8 × 8.7
35
100
RHS1V101MCN1GS
FP-035ME101M-HSR
700
0.12
25
3000
8 × 8.7
10
16
* In case of some doubt about measured values, measure after applying rated voltage for 120 minutes at 105°C.
zFrequency Characteristics
10000
10000
6.3V 390μF (HS series)
1000
1000
ESR (mΩ)
Impedance (mΩ)
6.3V 390μF (HS series)
100
100
10
10
1
1
0.1
1
10
100
1000
10000
0.1
1
10
Frequency (kHz)
100
1000
10000
Frequency (kHz)
zPart Number (EX) 6.3V, 390μF, HS series
Nichicon P/N
R
Type
FPCAP P/N
FP
Commodity
Mark
HS
0J
391
M
CN
1
GS
Series Name
Rated
Voltage
Rated
Capacitance
Capacitance
Tolerance
Configuration
Control Code
Taping
Code
6R3
ME
391
M
HS
R
Rated Voltage
Classification
Rated
Capacitance
Capacitance
Tolerance
Series Name
Taping
Code
NICHICON CORPORATION / FPCAP ELECTRONICS (SUZHOU) CO., LTD.
Control Code
33
Products / SMD Type
Functional Polymer Aluminum Solid Electrolytic Capacitors
SS & SA & SB series
Large
Capacitance
Low ESR
φ6.3
SMD
Lead-free
RoHS
Compliance
zFeatures
By using Functional Polymer cathode, Frequency & Temp.
characteristics are greatly improved.
‘ Low ESR at a high frequency range.
‘ High ripple current capability.
‘ Long life and high reliability.
zApplications
‘ Switching Power Supply and DC/DC Converter.
‘ Back up Power Supplies of CPU(VRM etc.)
‘ Miniature high Power Supply.
zEnvironmental Correspondence
Corresponding to Lead-free, RoHS compliance and Halogen-free.
‘ The Lead-free of terminal plating (Sn)
zRecommended land pattern
zSpecifications
c
Characteristic
SS, SA, SB
Operating temp. range
Rated voltage range
Capacitance range
Capacitance tolerance
-55 to +105°C
2.5 to 35V·DC
10 to 560μF
Test condition
Capacitance
Endurance Leakage current
ESR
tan δ
Failure Rate
105°C, rated voltage 2000Hrs.
Within ±20% of initial value before test
Not to exceed the initial specified value
Not to exceed 150% of initial specified value
Not to exceed 150% of initial specified value
0.5% / 1000Hrs. Max (60%CL)
b
[Unit: mm]
φD
6.3
SS
SA
4.0
(4.6)
SB
SA
6.3
(7.2)
SB
SS
SA
10
(11.5)
SB
SA
16
(18.4)
SS
SA
35
(40.2)
SS
SS
6.3×5.7 6.3×5.7
(60)
(60)
6.3×5.7
(40)
6.3×5.7
(40)
10
22
27
6.3×5.7
(30)
6.3×5.7
(30)
6.3×5.7
(30)
47
56
68
6.3×5.7
(25)
100
6.3×5.7
(22)
180
220
6.3×5.7 6.3×5.7 6.3×5.7
(25)
(15)
(12)
270
6.3×5.7
(14)
330
6.3×5.7
(14)
390
6.3×5.7 6.3×5.7 6.3×5.7
(14)
(10)
(14)
470
6.3×5.7
(13)
560
6.3×5.7 6.3×5.7 6.3×5.7
(25)
(13)
(10)
c
1.6
zDimensions
W ± 0.2
0.2 Max
P
L ± 0.3
R
6.3×5.7 6.3×7.7
(24)
(24)
6.3×5.7
(18)
120
34
25
(28.7)
b
3.5
H ± 0.2
[φD×L (mΩ)]
2.5
(2.8)
a
2.1
φD ± 0.5
Cap. [μF]
b
±20% (M)
zSize (ESR) List
R.V. (S.V.)
[V]
a
C ± 0.2
Items
[Unit: mm]
φD×L
6.3×5.7
W
H
C
R
P
6.5
6.5
7.2
0.5 to 0.9
2.1
6.3×7.7
6.5
6.5
7.2
0.5 to 0.9
2.1
6.3×5.7 6.3×5.7 6.3×5.7 6.3×5.7
(14)
(11)
(25)
(14)
NICHICON CORPORATION / FPCAP ELECTRONICS (SUZHOU) CO., LTD.
zPart number & Specifications
Rated
Voltage
Rated
Capacitance
(V)
(μF, 120Hz)
2.5
4.0
6.3
10
16
25
35
Part Number
Leakage
Current*
tanδ
ESR
Rated Ripple
Current
Case Size
NICHICON
FPCAP
(μA, 2 min)
(120Hz)
(mΩ, 100kHz)
(mA, r.m.s.)
φD×L(mm)
330
RSA0E331MCN1GS
FP-2R5ME331M-SAR
700
0.12
14
3160
6.3 × 5.7
390
RSA0E391MCN1GS
FP-2R5ME391M-SAR
700
0.12
14
3160
6.3 × 5.7
390
RSB0E391MCN1GS
FP-2R5ME391M-SBR
700
0.12
10
3650
6.3 × 5.7
470
RSA0E471MCN1GS
FP-2R5ME471M-SAR
700
0.12
13
3600
6.3 × 5.7
560
RSS0E561MCN1GS
FP-2R5ME561M-SSR
700
0.12
25
2500
6.3 × 5.7
560
RSA0E561MCN1GS
FP-2R5ME561M-SAR
700
0.12
13
3600
6.3 × 5.7
560
RSB0E561MCN1GS
FP-2R5ME561M-SBR
700
0.12
10
3800
6.3 × 5.7
330
RSA0G331MCN1GS
FP-4R0ME331M-SAR
700
0.12
14
3160
6.3 × 5.7
330
RSB0G331MCN1GS
FP-4R0ME331M-SBR
700
0.12
11
3700
6.3 × 5.7
390
RSA0G391MCN1GS
FP-4R0ME391M-SAR
700
0.12
14
3160
6.3 × 5.7
100
RSS0J101MCN1GS
FP-6R3ME101M-SSR
700
0.12
25
2500
6.3 × 5.7
220
RSS0J221MCN1GS
FP-6R3ME221M-SSR
700
0.12
25
2500
6.3 × 5.7
220
RSA0J221MCN1GS
FP-6R3ME221M-SAR
700
0.12
15
3160
6.3 × 5.7
220
RSB0J221MCN1GS
FP-6R3ME221M-SBR
700
0.12
12
3500
6.3 × 5.7
270
RSA0J271MCN1GS
FP-6R3ME271M-SAR
700
0.12
14
3160
6.3 × 5.7
330
RSS0J331MCN1GS
FP-6R3ME331M-SSR
700
0.12
25
2500
6.3 × 5.7
330
RSA0J331MCN1GS
FP-6R3ME331M-SAR
700
0.12
14
3160
6.3 × 5.7
120
RSA1A121MCN1GS
FP-010ME121M-SAR
700
0.12
18
2900
6.3 × 5.7
100
RSS1C101MCN1GS
FP-016ME101M-SSR
700
0.12
24
2490
6.3 × 5.7
100
RSA1C101MCN1GS
FP-016ME101M-SAR
700
0.12
24
2700
6.3 × 7.7
180
RSA1C181MCN1GS
FP-016ME181M-SAR
576
0.12
22
3300
6.3 × 5.7
10
RSS1E100MCN1GS
FP-025ME100M-SSR
100
0.12
60
1700
6.3 × 5.7
22
RSS1E220MCN1GS
FP-025ME220M-SSR
110
0.12
40
2100
6.3 × 5.7
27
RSS1E270MCN1GS
FP-025ME270M-SSR
135
0.12
40
2600
6.3 × 5.7
47
RSS1E470MCN1GS
FP-025ME470M-SSR
235
0.12
30
2800
6.3 × 5.7
56
RSS1E560MCN1GS
FP-025ME560M-SSR
280
0.12
30
2800
6.3 × 5.7
68
RSS1E680MCN1GS
FP-025ME680M-SSR
340
0.12
30
2800
6.3 × 5.7
10
RSS1V100MCN1GS
FP-035ME100M-SSR
100
0.12
60
1700
6.3 × 5.7
* In case of some doubt about measured values, measure after applying rated voltage for 120 minutes at 105°C.
zFrequency Characteristics
10000
10000
6.3V 220μF (SA series)
Impedance (mΩ)
6.3V 220μF (SA series)
1000
ESR (mΩ)
1000
100
100
10
10
1
1
0.1
1
10
100
1000
0.1
10000
1
10
Frequency (kHz)
100
1000
10000
Frequency (kHz)
zPart Number (EX) 6.3V, 220μF, SA series
Nichicon P/N
R
Type
FPCAP P/N
FP
Commodity
Mark
SA
0J
221
M
CN
1
GS
Series Name
Rated
Voltage
Rated
Capacitance
Capacitance
Tolerance
Configuration
Control Code
Taping
Code
6R3
ME
221
M
SA
R
Rated Voltage
Classification
Rated
Capacitance
Capacitance
Tolerance
Series Name
Taping
Code
NICHICON CORPORATION / FPCAP ELECTRONICS (SUZHOU) CO., LTD.
Control Code
35
Products / SMD Type
Functional Polymer Aluminum Solid Electrolytic Capacitors
FS & FA series
zFeatures
Large
Capacitance
φ4 , φ5
Low ESR
SMD
Lead-free
RoHS
Compliance
By using Functional Polymer cathode, Frequency & Temp.
characteristics are greatly improved.
‘ Low ESR at a high frequency range.
‘ High ripple current capability.
‘ Long life and high reliability.
zApplications
‘ Switching Power Supply and DC/DC Converter.
‘ Back up Power Supplies of CPU(VRM etc.)
‘ Miniature high Power Supply.
zEnvironmental Correspondence
Corresponding to Lead-free, RoHS compliance and Halogen-free.
‘ The Lead-free of terminal plating (Sn)
zRecommended land pattern
zSpecifications
c
Characteristic
FS, FA
-55 to +105°C
2.5 to 25V·DC
10 to 330μF
Test condition
Capacitance
Endurance Leakage current
ESR
tan δ
Failure Rate
105°C, rated voltage 2000Hrs.
Within ±20% of initial value before test
Not to exceed the initial specified value
Not to exceed 150% of initial specified value
Not to exceed 150% of initial specified value
0.5% / 1000Hrs. Max (60%CL)
FS
FA
[φD×L (mΩ)]
4.0
(4.6)
6.3
(7.2)
10
(11.5)
16
(18.4)
25
(28.7)
FS
FS
FS
4×5.2
(220)
FS
FS
5×5.7
(45)
5×5.7
(35)
5×5.7
(35)
5×5.7
(40)
10
22
33
39
5×5.7
(30)
68
5×5.7
(22)
100
120
b
c
1.0
2.6
1.6
5
1.4
3.0
1.6
zDimensions
W ± 0.2
0.2 Max
P
L ± 0.3
R
5×5.7
(24)
5×5.7
(24)
φD×L
4×5.2
W
H
C
4.3
4.3
5.1
5×5.7
5.3
5.3
5.9
5×5.7
(22)
150
330
a
5×5.7
(30)
47
180
φD
4
C ± 0.2
Cap. [μF]
2.5
(2.8)
b
φD ± 0.5
R.V. (S.V.)
[V]
a
[Unit: mm]
±20% (M)
zSize (ESR) List
36
b
Operating temp. range
Rated voltage range
Capacitance range
Capacitance tolerance
H ± 0.2
Items
5×5.7
(21)
5×5.7
(10)
NICHICON CORPORATION / FPCAP ELECTRONICS (SUZHOU) CO., LTD.
[Unit: mm]
P
0.5 to 0.9 1.0
0.5 to 0.9 1.4
R
zPart number & Specifications
Rated
Voltage
Rated
Capacitance
(V)
(μF, 120Hz)
2.5
4.0
6.3
10
16
25
Part Number
Leakage
Current *
tanδ
ESR
Rated Ripple
Current
Case Size
NICHICON
FPCAP
(μA, 2 min)
(120Hz)
(mΩ, 100kHz)
(mA, r.m.s.)
φD×L(mm)
180
RFS0E181MCN1GS
FP-2R5ME181M-FSR
300
0.12
21
2670
5 × 5.7
330
RFA0E331MCN1GS
FP-2R5ME331M-FAR
500
0.12
10
3300
5 × 5.7
100
RFS0G101MCN1GS
FP-4R0ME101M-FSR
300
0.12
22
2610
5 × 5.7
150
RFS0G151MCN1GS
FP-4R0ME151M-FSR
300
0.12
22
2610
5 × 5.7
47
RFS0J470MCN1GS
FP-6R3ME470M-FSR
300
0.12
30
2000
5 × 5.7
100
RFS0J101MCN1GS
FP-6R3ME101M-FSR
300
0.12
24
2500
5 × 5.7
120
RFS0J121MCN1GS
FP-6R3ME121M-FSR
300
0.12
24
2500
5 × 5.7
10
RFS1A100MCN1GB
FP-010ME100M-FSR
100
0.12
220
700
4 × 5.2
68
RFS1A680MCN1GS
FP-010ME680M-FSR
300
0.12
30
2000
5 × 5.7
22
RFS1C220MCN1GS
FP-016ME220M-FSR
100
0.12
45
1210
5 × 5.7
33
RFS1C330MCN1GS
FP-016ME330M-FSR
105
0.12
35
2070
5 × 5.7
39
RFS1C390MCN1GS
FP-016ME390M-FSR
125
0.12
35
2070
5 × 5.7
22
RFS1E220MCN1GS
FP-025ME220M-FSR
300
0.12
40
2200
5 × 5.7
* In case of some doubt about measured values, measure after applying rated voltage for 120 minutes at 105°C.
zFrequency Characteristics
10000
10000
4.0V 150μF (FS series)
1000
1000
ESR (mΩ)
Impedance (mΩ)
4.0V 150μF (FS series)
100
10
100
10
1
1
0.1
1
10
100
1000
0.1
10000
1
10
Frequency (kHz)
100
1000
10000
Frequency (kHz)
zPart Number (EX) 2.5V, 330μF, FA series
Nichicon P/N
R
Type
FPCAP P/N
FP
Commodity
Mark
FA
0E
331
M
CN
1
Series Name
Rated
Voltage
Rated
Capacitance
Capacitance
Tolerance
Configuration
Control Code
GS
Taping
Code
Taping Code:
GB: Height under 5.2mm
GS: Height over 5.7mm
2R5
ME
331
M
FA
R
Rated Voltage
Classification
Rated
Capacitance
Capacitance
Tolerance
Series Name
Taping
Code
NICHICON CORPORATION / FPCAP ELECTRONICS (SUZHOU) CO., LTD.
Control Code
37
Products / SMD Type
Functional Polymer Aluminum Solid Electrolytic Capacitors
SL series
zFeatures
Low Profile
4.5mmMax
φ6.3
Large
Capacitance
Lead-free
RoHS
Compliance
By using Functional Polymer cathode, Frequency & Temp.
characteristics are greatly improved.
‘ Low ESR at a high frequency range.
‘ High ripple current capability.
‘ Low profile type. (Height : 4.5mmMax.)
zApplications
‘ Switching Power Supply and DC/DC Converter.
‘ Back up Power Supplies of CPU(VRM etc.)
‘ Miniature high Power Supply.
zEnvironmental Correspondence
Corresponding to Lead-free, RoHS compliance and Halogen-free.
‘ The Lead-free of terminal plating (Sn)
zRecommended land pattern
zSpecifications
c
Characteristic
SL
-55 to +105°C
2.5 to 25V·DC
15 to 330μF
Test condition
Capacitance
Endurance Leakage current
ESR
tan δ
Failure Rate
105°C, rated voltage 2000Hrs.
Within ±20% of initial value before test
Not to exceed the initial specified value
Not to exceed 150% of initial specified value
Not to exceed 150% of initial specified value
0.5% / 1000Hrs. Max (60%CL)
[φD×L (mΩ)]
6.3
(7.2)
15
100
6.3×4.2
(16)
150
220
330
6.3×4.2
(16)
6.3×4.2
(16)
6.3×4.2
(18)
6.3×4.2
(18)
6.3×4.2
(18)
16
(18.4)
25
(28.7)
6.3×4.2
(45)
6.3×4.2
(55)
φD
6.3
a
b
c
2.1
3.5
1.6
zDimensions
W ± 0.2
0.2 Max
C ± 0.2
Cap. [μF]
2.5
(2.8)
b
H ± 0.2
R.V. (S.V.)
[V]
a
[Unit: mm]
±20% (M)
zSize (ESR) List
38
b
Operating temp. range
Rated voltage range
Capacitance range
Capacitance tolerance
φD ± 0.5
Items
P
L ± 0.3
R
[Unit: mm]
φD×L
6.3×4.2
W
H
C
R
P
6.5
6.5
7.2
0.5 to 0.9
2.1
NICHICON CORPORATION / FPCAP ELECTRONICS (SUZHOU) CO., LTD.
zPart number & Specifications
Rated
Voltage
Rated
Capacitance
(V)
(μF, 120Hz)
Part Number
Leakage
Current *
tanδ
ESR
Rated Ripple
Current
Case Size
NICHICON
FPCAP
(μA, 2 min)
(120Hz)
(mΩ, 100kHz)
(mA, r.m.s.)
φD×L(mm)
100
RSL0E101MCN1GB
FP-2R5ME101M-SLR
300
0.12
16
3500
6.3 × 4.2
220
RSL0E221MCN1GB
FP-2R5ME221M-SLR
300
0.12
16
3500
6.3 × 4.2
330
RSL0E331MCN1GB
FP-2R5ME331M-SLR
413
0.12
16
3500
6.3 × 4.2
100
RSL0J101MCN1GB
FP-6R3ME101M-SLR
315
0.12
18
3200
6.3 × 4.2
150
RSL0J151MCN1GB
FP-6R3ME151M-SLR
473
0.12
18
3200
6.3 × 4.2
220
RSL0J221MCN1GB
FP-6R3ME221M-SLR
693
0.12
18
3200
6.3 × 4.2
16
15
RSL1C150MCN1GB
FP-016ME150M-SLR
300
0.12
45
1900
6.3 × 4.2
25
15
RSL1E150MCN1GB
FP-025ME150M-SLR
100
0.12
55
1700
6.3 × 4.2
2.5
6.3
* In case of some doubt about measured values, measure after applying rated voltage for 120 minutes at 105°C.
zFrequency Characteristics
10000
10000
6.3V 220μF (SL series)
1000
1000
ESR (mΩ)
Impedance (mΩ)
6.3V 220μF （ SL series)
100
10
100
1
10
1
0.1
1
10
100
1000
10000
0.1
1
10
Frequency (kHz)
100
1000
10000
Frequency (kHz)
zPart Number (EX) 2.5V, 330μF, SL series
Nichicon P/N
R
Type
FPCAP P/N
FP
Commodity
Mark
SL
0E
331
M
CN
1
GB
Series Name
Rated
Voltage
Rated
Capacitance
Capacitance
Tolerance
Configuration
Control Code
Taping
Code
2R5
ME
331
M
SL
R
Rated Voltage
Classification
Rated
Capacitance
Capacitance
Tolerance
Series Name
Taping
Code
NICHICON CORPORATION / FPCAP ELECTRONICS (SUZHOU) CO., LTD.
Control Code
39
Products / SMD Type
Functional Polymer Aluminum Solid Electrolytic Capacitors
VA & VB & VC series
SMD
7.3×4.3×2.8
3mm Height
Low ESR
Lead-free
RoHS
Compliance
zFeatures
By using Aluminum Functional Polymer.
‘ Low ESR at a high frequency range.
‘ High ripple current capability.
zApplications
‘ Switching Power Supply and DC/DC Converter.
‘ Back up Power Supplies of CPU(VRM etc.)
‘ Miniature high Power Supply.
zEnvironmental Correspondence
Corresponding to Lead-free, RoHS compliance and Halogen-free.
‘ The Lead-free of terminal plating.
zSpecifications
zRecommended land pattern
Characteristic
Items
VA, VB, VC
Operating temp. range
-55 to +105°C
Rated voltage range
2.0 to 25V·DC
Capacitance range
15 to 330μF
Capacitance tolerance
±20% (M)
Not to exceed 150% of initial specified value
60°C,90~95%RH, No Bias, 500Hrs.
Test condition
Within +50%-20% of initial value before test
Capacitance
Leakage current
Not to exceed 300% of initial specified value
tan δ
Not to exceed 200% of initial specified value
Failure Rate
0.5% / 1000Hrs. Max (60%CL)
zSize Code (ESR) List
Cap. [μF]
2.0
(2.3)
VB
[Size Code (mΩ)]
2.5
(2.8)
VC
VA
4.0
(4.6)
VB
VA
6.3
(7.2)
VB
VA
VB
15
27
33
47
N
(25)
100
N
(18)
150
N
(18)
220
330
40
N
(15)
b
Not to exceed the initial specified value
Leakage current
R.V. (S.V.)
[V]
a
Within ±20% of initial value before test
Capacitance
tan δ
Damp Heat
b
105°C, rated voltage 1000Hrs.
Test condition
Endurance
c
N
(9)
N
(15)
N
(15)
N
(15)
16
25
(18.4) (28.7)
VA
VA
N
(60)
N
N
(60)
(55)
N
(55)
N
(55)
[Unit: mm]
Size Code
L×W×H
N
7.3 × 4.3 × 2.8
a
b
c
4.1
2.05
2.9
zDimensions
L
W1
H
Z
Z
N
(20)
N
(20)
W2
[Unit: mm]
Size Code
L×W×H
N
7.3 × 4.3 × 2.8
L±0.2
7.3
W1±0.2 W2±0.1
4.3
2.4
NICHICON CORPORATION / FPCAP ELECTRONICS (SUZHOU) CO., LTD.
H±0.2
Z±0.2
2.8
1.3
zPart number & Specifications
Rated
Rated
Voltage
Capacitance
(V)
Leakage
Current*
Part Number
(μF, 120Hz)
tanδ
Rated Ripple
Current
Size
MSL
(m A, r.m.s.)
L×W×H(mm)
(J-STD-020D)
15
2800
7.3 × 4.3 × 2.8
Level 3
ESR
(mΩ,
NICHICON
FPCAP
(μA, 2 min)
(120Hz)
330
RVB0D331MNG
FP-2R0CM331M-VBR
700
0.12
330
RVC0D331MNG
FP-2R0CM331M-VCR
700
0.12
9
3300
7.3 × 4.3 × 2.8
Level 3
220
RVA0E221MNG
FP-2R5CM221M-VAR
700
0.12
18
2600
7.3 × 4.3 × 2.8
Level 3
220
RVB0E221MNG
FP-2R5CM221M-VBR
700
0.12
15
2800
7.3 × 4.3 × 2.8
Level 3
150
RVA0G151MNG
FP-4R0CM151M-VAR
700
0.12
18
2600
7.3 × 4.3 × 2.8
Level 3
150
RVB0G151MNG
FP-4R0CM151M-VBR
700
0.12
15
2800
7.3 × 4.3 × 2.8
Level 3
220
RVB0G221MNG
FP-4R0CM221M-VBR
1000
0.12
15
2800
7.3 × 4.3 × 2.8
Level 3
100
RVA0J101MNG
FP-6R3CM101M-VAR
700
0.12
25
2000
7.3 × 4.3 × 2.8
Level 3
100
RVB0J101MNG
FP-6R3CM101M-VBR
700
0.12
20
2400
7.3 × 4.3 × 2.8
Level 3
150
RVB0J151MNG
FP-6R3CM151M-VBR
1000
0.12
20
2400
7.3 × 4.3 × 2.8
Level 3
27
RVA1C270MNG
FP-016CM270M-VAR
216
0.12
55
1100
7.3 × 4.3 × 2.8
Level 3
33
RVA1C330MNG
FP-016CM330M-VAR
264
0.12
55
1100
7.3 × 4.3 × 2.8
Level 3
47
RVA1C470MNG
FP-016CM470M-VAR
376
0.12
55
1100
7.3 × 4.3 × 2.8
Level 3
15
RVA1E150MNG
FP-025CM150M-VAR
188
0.12
60
1000
7.3 × 4.3 × 2.8
Level 3
27
RVA1E270MNG
FP-025CM270M-VAR
337
0.12
60
1000
7.3 × 4.3 × 2.8
Level 3
100kHz)
2.0
2.5
4.0
6.3
16
25
* In case of some doubt about measured values, measure after applying rated voltage for 120 minutes at 105°C.
zFrequency Characteristics
Impedance (mΩ)
100000
100000
16V33µF (VA series) Imp.
16V33µF (VA series) ESR
25V15µF (VA series) Imp.
25V15µF (VA series) ESR
10000
ESR (mΩ)
10000
1000
100
1000
100
10
10
0.1
1
10
100
1000
10000
0.1
1
10
100
1000
10000
Frequency (kHz)
Frequency (kHz)
zPart Number (EX) 2.0V, 330μF, VB series
Nichicon P/N
R
Type
FPCAP P/N
FP
Commodity
Mark
VB
0D
331
M
N
Series Name
Rated
Voltage
Rated
Capacitance
Capacitance
Tolerance
Size Code
(N: 7.3×4.3×2.8)
G
Control Code
Taping
Code
2R0
CM
331
M
VB
R
Rated Voltage
Classification
Rated
Capacitance
Capacitance
Tolerance
Series Name
Taping
Code
NICHICON CORPORATION / FPCAP ELECTRONICS (SUZHOU) CO., LTD.
Control Code
41
Products / SMD Type
Functional Polymer Aluminum Solid Electrolytic Capacitors
UA & UB series
SMD
7.3×4.3×1.9
2mm Height
Low ESR
Lead-free
RoHS
Compliance
zFeatures
By using Aluminum Functional Polymer.
‘ Low ESR at a high frequency range.
‘ High ripple current capability.
zApplications
‘ Switching Power Supply and DC/DC Converter.
‘ Back up Power Supplies of CPU(VRM etc.)
‘ Miniature high Power Supply.
zEnvironmental Correspondence
Corresponding to Lead-free, RoHS compliance and Halogen-free.
‘ The Lead-free of terminal plating.
zSpecifications
zRecommended land pattern
Characteristic
Items
UA, UB
Operating temp. range
-55 to +105°C
Rated voltage range
2.0 to 25V·DC
Capacitance range
15 to 220μF
±20% (M)
Capacitance tolerance
60°C,90~95%RH, No Bias, 500Hrs.
Within +50%-20% of initial value before test
Capacitance
Leakage current
Not to exceed 300% of initial specified value
tan δ
Not to exceed 200% of initial specified value
Failure Rate
0.5% / 1000Hrs. Max (60%CL)
zSize Code (ESR) List
2.0
(2.3)
UA
UB
[Size Code (mΩ)]
4.0
(4.6)
UA
6.3
(7.2)
UA
16
(18.4)
UA
15
L
(65)
27
220
L
(15)
L
(9)
b
c
4.1
2.05
2.9
W1
L
H
Z
Z
W2
L
(18)
150
a
zDimensions
25
(28.7)
UA
L
(70)
L
(25)
100
42
[Unit: mm]
Size Code
L×W×H
L
7.3 × 4.3 × 1.9
Not to exceed 150% of initial specified value
Test condition
Cap. [μF]
b
Not to exceed the initial specified value
Leakage current
R.V. (S.V.)
[V]
a
Within ±20% of initial value before test
Capacitance
tan δ
Damp Heat
b
105°C, rated voltage 1000Hrs.
Test condition
Endurance
c
[Unit: mm]
Size Code
L×W×H
L
7.3 × 4.3 × 1.9
L±0.2
7.3
W1±0.2 W2±0.1
4.3
2.4
NICHICON CORPORATION / FPCAP ELECTRONICS (SUZHOU) CO., LTD.
H±0.1
Z±0.2
1.9
1.3
zPart number & Specifications
Rated
Rated
Voltage
Capacitance
(V)
Leakage
Current*
Part Number
(μF, 120Hz)
220
tanδ
NICHICON
FPCAP
(μA, 2 min)
(120Hz)
RUA0D221MLG
FP-2R0CM221M-UAR
700
0.12
ESR
Rated Ripple
Current
Size
MSL
(mA, r.m.s.)
L×W×H(mm)
(J-STD-020D)
2800
7.3 × 4.3 × 1.9
Level 3
(mΩ,
100kHz)
15
2.0
220
RUB0D221MLG
FP-2R0CM221M-UBR
700
0.12
9
3300
7.3 × 4.3 × 1.9
Level 3
4.0
150
RUA0G151MLG
FP-4R0CM151M-UAR
700
0.12
18
2600
7.3 × 4.3 × 1.9
Level 3
6.3
100
RUA0J101MLG
FP-6R3CM101M-UAR
700
0.12
25
2300
7.3 × 4.3 × 1.9
Level 3
16
27
RUA1C270MLG
FP-016CM270M-UAR
216
0.12
65
1100
7.3 × 4.3 × 1.9
Level 3
25
15
RUA1E150MLG
FP-025CM150M-UAR
188
0.12
70
1000
7.3 × 4.3 × 1.9
Level 3
* In case of some doubt about measured values, measure after applying rated voltage for 120 minutes at 105°C.
zFrequency Characteristics
Impedance (mΩ)
100000
100000
16V27μF (UA series) Imp.
16V27µF (UA series) ESR
25V15μF (UA series) Imp.
25V15µF (UA series) ESR
10000
ESR (mΩ)
10000
1000
100
1000
100
10
10
0.1
1
10
100
1000
10000
0.1
1
10
Frequency (kHz)
100
1000
10000
Frequency (kHz)
zPart Number (EX) 25V, 15μF, UA series
Nichicon P/N
R
Type
FPCAP P/N
FP
Commodity
Mark
UA
1E
150
M
L
Series Name
Rated
Voltage
Rated
Capacitance
Capacitance
Tolerance
Size Code
(L: 7.3×4.3×1.9)
G
Control Code
Taping
Code
025
CM
150
M
UA
R
Rated Voltage
Classification
Rated
Capacitance
Capacitance
Tolerance
Series Name
Taping
Code
NICHICON CORPORATION / FPCAP ELECTRONICS (SUZHOU) CO., LTD.
Control Code
43
Ordering Information
Functional Polymer Aluminum Solid Electrolytic Capacitors
Type Numbering System （Example:2.5V560μF L8）
Nichicon Part Number
R
L8
0E
561
M
DN
1
Type
Series Name
Rated
Voltage
Rated
Capacitance
Capacitance
Tolerance
Configuration
UA, UB series
Size Code : L
VA, VB, VC series
Size Code : N
Control Code
FPCAP Part Number
FP
2R5
RE
561
M
L8
R
Commodity
Mark
Rated Voltage
Classification
Rated
Capacitance
Capacitance
Tolerance
Series Name
Taping &
Lead Forming
Type & Classification
Nichicon
Type &
P/N
Classification
Symbol
RE
R
ME
SMD Type
CM
5000hrs
2000hrs
VA, VB, VC series
UA, UB series
Series
Voltage
[V]
NS
R7
R5
L8
E5
Radial Lead
S8
Type
F8
NU
NE
S6
HT
PS, PA
HS, HA
SS, SA, SB
SMD Type
FS,FA
SL
VA, VB, VC
UA,UB
2.0
2.5
4.0
6.3
10
16
20
25
35
50
63
Nichicon
P/N
Symbol
0D
0E
0G
0J
1A
1C
1D
1E
1V
1H
1J
FPCAP
P/N
Symbol
2R0
2R5
4R0
6R3
010
016
020
025
035
050
063
Capacitance
[μF]
Symbol
8.2
10
22
100
220
1500
8R2
100
220
101
221
152
Capacitance Tolerance
Tolerances
Symbol
± 20%
M
Taping & Lead Forming
Control Code*
Endurance
Classification
Control Code
Rated Capacitance
Rated Voltage
Series Name
FPCAP
P/N
Symbol
Radial Lead
Type
Nichicon
P/N
Symbol
ASQ
1
FPCAP
P/N
Symbol
-5K
no sign
no sign
no sign
Classification
Taping &
Lead Forming
Long lead (Bulk)
Cut lead (Bulk)
Radial Lead
Type
* In case of endurance
2.5mm pitch taping
3.5mm pitch taping
5.0mm pitch taping
SMD Type
Taping
Bulk
44
Taping &
Lead Forming
Case Size
(mm)
Nichicon
P/N
Symbol
FPCAP
P/N
Symbol
All
All
φ5×8, φ6.3×5 to 8
φ5×10, φ6.3×10
φ8
φ5, φ6.3, φ8
φ10
Height under 5.2mm
Height over 5.7mm
7.3×4.3×1.9 / 2.8
All
no sign
CG
JT
JX
KX
PX
PH
GB
GS
G
no sign
R
CG
JT
J
K
P
PH
NICHICON CORPORATION / FPCAP ELECTRONICS (SUZHOU) CO., LTD.
R
N
Packing Specifications
Functional Polymer Aluminum Solid Electrolytic Capacitors
Ammo Pack Taping Specifications (Radial Lead Type)
Taping Dimensions
Lead Forming (Symbol: Ex. PX) Nichicon P/N Symbol : R………………… M……1 PX
FPCAP P/N Symbol : FP-………RE………M-…… P
2.5mm pitch taping
2.5mm pitch taping
Taping Dimensions for φ5
Nichicon P/N Symbol : JT (φ5×8) , JX (φ5×10)
FPCAP P/N Symbol : JT (φ5×8) , J (φ5×10)
Δh1
Δh2
P2
P
L
P3
φd
e
W0
W
D0
P1
h
h
P1
φd
t
W0
W
H0
H
W1
e
Δh2
H
W1
f
f
W2
P3
Δh1
D
L
D
t
P
Nichicon P/N Symbol : JT (φ6.3×5 to 8) , JX (φ6.3×10)
FPCAP P/N Symbol : JT (φ6.3×5 to 8) , J (φ6.3×10)
W2
P2
Taping Dimensions for φ6.3
D0
5.0mm pitch taping
3.5mm(φ8) or 5.0mm(φ10) pitch taping
Nichicon P/N Symbol : PX
FPCAP P/N Symbol : P
Nichicon P/N Symbol : KX (φ8) , PH (φ10)
FPCAP P/N Symbol : K (φ8) , PH (φ10)
Taping Dimensions for φ5, φ6.3, φ8
Δh1
Δh2
P2
P
P1
φd
H
W1
f
W0
W
t
e
W2
D0
P1
h
h
W0
W
H0
H
W1
f
e
Δh2
L
L
P3
φd
P3
Δh1
D
t
P
D
W2
P2
Taping Dimensions for φ8, φ10
D0
Specification Table
Item
[Unit : mm]
φD×L
6.3×6,
6.3×7
5×8,
6.3×8
6.3×5
5×10,
6.3×10
6.3×6,
6.3×7
5×8,
6.3×8
5×10,
6.3×5,
6.3×10
8×6 , 8×8 ,
8×9 , 8×11.5
10×12.5
Lead Forming Symbol (Nichicon P/N)
JT
JX
PX
PX
KX
Lead Forming Symbol (FPCAP P/N)
JT
J
P
P
K
PH
0.6
0.6
0.6
Lead Wire Diameter
φd
Tolerance
0.45
±0.05
0.6
0.5
0.5
0.45
±0.05
±0.05
±0.05
±0.05
0.6
0.5
±0.05
±0.05
PH
±0.05
±0.05
±0.05
Lead Wire Interval
f
2.5 +0.8/-0.2 (φ6.3: 2.5±0.5)
5.0 +0.8/-0.2
5.0 +0.8/-0.2
3.5 +0.8/-0.2
5.0 +0.8/-0.2
Pitch Between Components
P
12.7±1.0
12.7±1.0
12.7±1.0
12.7±1.0
12.7±1.0
Feed Holes Position Gap
P1
12.7±0.3
12.7±0.3
12.7±0.3
12.7±0.3
12.7±0.3
Feed Holes Position Gap
P2
6.35±1.0
6.35±1.0
6.35±1.0
6.35±0.5
6.35±0.5
Lead Wire Clinch Height
H0
-
16.0±0.5
16.0±0.5
-
-
20.0±0.75
20.0±0.5
18.5±0.5
Components Height
H
18.5±0.5
17.5±0.5
Base Tape
W
18.0 +1.0/-0.5
18.0 +1.0/-0.5
Feed Holes Position Gap
W1
9.0±0.5
9.0±0.5
Feed Hole Diameter
D0
4.0±0.2
4.0±0.2
4.0±0.2
4.0±0.2
4.0±0.2
Components Alignment
∆h
2.0 max
2.0 max
2.0 max
2.0 max
2.0 max
t
0.7±0.2
0.7±0.2
0.7±0.2
0.7±0.2
0.7±0.2
Tape Thickness
18.0 +1.0/-0.5 18.0 +1.0/-0.5 18.0 +1.0/-0.5
9.0±0.5
9.0±0.5
NICHICON CORPORATION / FPCAP ELECTRONICS (SUZHOU) CO., LTD.
9.0±0.5
45
Packing Specifications
Ammo Pack Quantity Unit
Packing Quantity (Ammo Pack)
Size (dia)
Packing Unit
(pcs / Ammo Pack)
φ5
φ6.3
2,000
2,000
φ8
φ10
1,000
500
Ammo pack
340Max
60Max
320Max
Polarity mark
+
[Unit : mm]
The lid of feeding side of the taping box shall be torn off at the perforation line.
Bulk Packing Quantity Unit (Radial Lead Type)
Components are packaged as per following packing unit.
Packing Quantity (Bulk)
Long Lead
Cut Lead
Case Size
φD×L
(mm)
Inner Bag
(pcs)
Packing Unit
(pcs / Carton Box)
Inner Bag
(pcs)
Packing Unit
(pcs / Carton Box)
4×5
200
8,000
200
8,000
5×8, 5×10
200
3,200
200
4,000
6.3×5, 6.3×6, 6.3×7
200
4,000
200
4,000
6.3×8, 6.3×10
200
3,200
200
4,000
8×6, 8×8, 8×9
200
3,200
200
4,000
8×11.5
100
2,000
200
2,400
10×12.5
100
1,600
100
2,000
Note:Please inquire for FPCAP by Packing Unit as above.
Cut Lead (Bulk) Dimensions
φD×L
Item
Lead Forming Symbol
46
L
H
f
φD
Lead Forming (Symbol: CG)
Nichicon P/N
: R………………… M……1 CG
FPCAP P/N
: FP-………RE………M-…… CG
φd
[Unit: mm]
4×5
5×8, 5×10
6.3×5, 6.3×6
6.3×7, 6.3×8, 6.3×10
CG
CG
CG
CG
CG
0.45, 0.6, 0.5±0.05
0.6±0.05
0.6±0.05
0.45±0.05 0.6, 0.5±0.05
8×6, 8×8, 8×9, 8×11.5
10×12.5
Lead Wire Diameter
φd
Lead Wire Length
H
3.1±0.3
3.1±0.3
3.1±0.3
3.1±0.3
3.1±0.3
Lead Wire Interval
f
1.5±0.5
2.0±0.5
2.5±0.5
3.5±0.5
5.0±0.5
NICHICON CORPORATION / FPCAP ELECTRONICS (SUZHOU) CO., LTD.
Packing Specifications
Packaging Unit Quantity for a Reel (SMD Type)
Components are packaged as per following packing unit
Packing Quantity (Reel)
PS, PA, HS, HA, SS, SA, SB, FS, FA, SL series
VA, VB, VC, UA, UB series
Case Size
φD×L
(mm)
Reel
(pcs)
Case Size
L×W×H
(mm)
Reel
(pcs)
4×5.2
2,000
7.3×4.3×1.9
3,000
5×5.7
1,000
7.3×4.3×2.8
2,500
6.3×4.2
1,000
6.3×5.7
1,000
6.3×7.7
900
8×6.7
1,000
8×7.7
900
8×8.7
500
8×11.7
500
10×7.7
500
10×12.4
400
Note:Please inquire for FPCAP by Packing Unit as above.
E
C
A B
R
D
W1
Dimensions of Reel
W2
PS, PA, HS, HA, SS, SA, SB, FS, FA, SL series
Size (dia)
φ4, φ5
φ6.3
A
±2.0
380
B
±1.0
80
C
±0.5
13.0
D
±1.0
21
E
±0.5
2.0
W1
±1.0
13.4
[Unit : mm]
W2
±1.0
17.4
R
1.0
380
80
13.0
21
2.0
17.4
21.4
1.0
380
80
13.0
21
2.0
25.4
29.4
1.0
7.3×4.3×1.9
A
±2.0
330
B
±1.0
80
C
±0.5
13.0
D
±1.0
21
E
±0.5
2.0
W1
±1.0
13.4
W2
±1.0
17.4
1.0
7.3×4.3×2.8
330
80
13.0
21
2.0
13.4
17.4
1.0
φ8, φ10
VA, VB, VC, UA, UB series
Size
L×W×H
R
NICHICON CORPORATION / FPCAP ELECTRONICS (SUZHOU) CO., LTD.
47
Materials and Soldering
Functional Polymer Aluminum Solid Electrolytic Capacitors
Materials
Terminals
Cu wire
Fe wire
100%Sn (Thickness/12μm)
Cu (Thickness/22.5 to 30μm)
Fe
Cu
100%Sn (Thickness/13μm)
Compositions
Radial Lead Type
Cathode Terminal
Anode
Terminal
SMD (Can) Type
Anode Foil
Cathode Foil
Electrolyte and
Separator Sheet
Element
Sealing Material
Base
Plastic coating
Aluminum Case
Sealing Material
Stand off
Plastic coating Aluminum Anode Terminal
Case
Electrolyte and
Separator Sheet
Element
Cathode Terminal
SMD (Molded Chip) Type
Electrolyte and
Separator Sheet
Molded Resin
Anode Foil
Anode Foil
Cathode Foil
Cathode Foil
Cathode Terminal
Anode Terminal
Materials
Composition Part
Radial Lead Type
Anode Foil
Can Type
Aluminum
Cathode Foil
Aluminum
Electrolytic Capacitor Paper
Separator Sheet
Electrolyte
Terminal
Functional Polymer
1)Iron Lead / Copper Plating + Tin Plating
2)Copper Lead / Tin Plating
Aluminum Case
Sealing Material
48
SMD Type
Molded Chip Type
Copper Lead / Tin
Plating
Aluminum + Plastic
Rubber
Copper Lead / Palladium
+ Gold Plating
-
Base
-
Plastic
-
Molded Resin
-
-
Epoxy Resin
NICHICON CORPORATION / FPCAP ELECTRONICS (SUZHOU) CO., LTD.
Materials and Soldering
Soldering Profile
Flow Soldering (Radial Lead Type)
Recommended Flow Profile
Temperature (ºC)
300
Soldering
Peak Flow Temp:260ºC max.
250
200
150
Pre-heat Temp:125ºC Max
100
Within 10sec.
50
Within 120sec.
0
Time (sec)
Reflow Soldering (SMD Type)
Reflow Profile
Peak Temperature
230ºC
200(or217)ºC
180ºC
150ºC
B
Preheating
A
PS, PA, HS, HA, SS, SA, SB, FS, FA, SL
VA, VB, VC, UA, UB
Item
Recommended
Condition 1
Recommended
Condition 2
Recommended
Condition 3
Recommended
Condition 4
Peak Temperature
260ºC or less
250ºC or less
260ºC or less
(Within 5 seconds)
250ºC or less
(Within 5 seconds)
Preheating
150ºC to 180ºC
Within 90 seconds
150ºC to 180ºC
Within 90 seconds
150ºC to 180ºC
Within 90 seconds
150ºC to 180ºC
Within 120 seconds
A
200ºC and higher
Within 60 seconds
200ºC and higher
Within 60 seconds
217ºC and higher
Within 60 seconds
217ºC and higher
Within 60 seconds
B
230ºC and higher
Within 40 seconds
230ºC and higher
Within 40 seconds
-
-
The Number of
Reflow
Only 1 time
Twice or less
Only 1 time
Twice or less
NICHICON CORPORATION / FPCAP ELECTRONICS (SUZHOU) CO., LTD.
49
Technical Guide
Functional Polymer Aluminum Solid Electrolytic Capacitors
Construction and Characteristics of
Construction of
Al Foil
Al Foil
Functional Polymer
(&Separator)
Case
Sealing Rubber
Lead ( + )
Lead ( - )
FPCAP is roughly the same construction as an aluminum electrolytic capacitor,
and uses rolled aluminum foils in its capacitor element.
Manufacturing Process of
Etched Al Foil
Forming
Slitting
Winding
Tab Terminal
Separator Sheet
Forming
Functional Polymer
Polymerization
Sealing
Assembling Parts
Aging and Inspection
Shipping
50
NICHICON CORPORATION / FPCAP ELECTRONICS (SUZHOU) CO., LTD.
Technical Guide
Equivalent Circuit of Capacitor
100
10
Rp
Cp : Capacitance
Rp : Equivalent parallel
resistance
(Insulation resistance)
( ≅Rated Voltage/LC)
Rs : Equivalent series
resistance
L : Inductance
Rs
L
Imp / ESR (Ω)
Cp
Imp
1/ωC
1
ωL
100m
10m
ESR
R
1m
100
1k
10k
100k
10M
100M
Frequency (Hz)
2
⎫
⎧
⎫ ⎧
Rp
ωCpRp 2
L
Z = ⎨Rs +
+
ω
−
⎨
2
2
2 ⎬
2
2
2 ⎬
1 + ω Cp Rp ⎭
1 + ω Cp Rp ⎭ ⎩
⎩
(
1M
)
(
2
)
Feature of Functional Polymer
Resistivity (Ω⋅cm)
100
10
1
0.1
0.01
Electrolyte (Aluminum Electrolytic Capacitor)
Manganese Dioxide
(Tantalum Solid Electrolytic Capacitor)
TCNQ Complex Salt
(Organic Semiconductive Capacitor)
PPY by Chemical Polymerization
PPY by Electrolytic Polymerization
Conductive Polymer (PEDOT)
O
O
S
S
O
PEDT
PEDOT
O
n
FPCAP differs from the aluminum electrolytic capacitor in that in place of the electrolyte,
functional polymer is impregnated.
NICHICON CORPORATION / FPCAP ELECTRONICS (SUZHOU) CO., LTD.
51
Technical Guide
Typical Electrical Characteristics of Capacitors
Frequency Dependence
100
100
TA Cap
TA Cap
AL E-Cap 220µF
10
FPCAP
220µF
AL E-Cap 220µF
10
270µF
FPCAP
1
ESR (Ω)
Impedance (Ω)
220µF
0.1
0.01
270µF
1
0.1
0.01
0.001
100
1k
10k
100k
1M
10M
0.001
100
100M
1k
10k
Frequency (Hz)
100k
1M
10M
100M
Frequency (Hz)
FPCAP has excellent frequency characteristic nearly equal to the film capacitor.
Using the high conductivity of the Functional polymer with an electrolyte, and adopting the
winding element for layer thinness of electrolyte, the ESR is improved greatly and has the
frequency characteristic that is nearly equal to the film capacitor.
Typical Temperature Dependence of Capacitors
20
10
MLCC
TA Cap
AL E-cap
FPCAP
0
MLCC
TA Cap
AL E-cap
FPCAP
-10
-20
-30
-40
1
ESR (Ω)
Capacitance (ΔC/C %)
10
0.1
0.01
-50
-60
0.001
-60 -40 -20
0 20 40 60 80 100 120
Temperature (°C)
-60 -40 -20
0
20
40
60
80
100 120
Temperature (°C)
The temperature dependence of the FPCAP is that it features little change in
temperature for the ESR.
Since ESR is dominant at high range of impedance (near resonance point),
the ESR value greatly affects Noise clearing capacity.
What ESR changes little against temperature means that Noise clearing ability
changes little against temperature as well.
52
NICHICON CORPORATION / FPCAP ELECTRONICS (SUZHOU) CO., LTD.
Technical Guide
Frequency Dependence
10000
1000
1000
ESR (mΩ)
Impedance (mΩ)
10000
L8 series 2.5V 560µF (φ8×8L)
NU series 6.3V 1000µF (φ8×11.5L)
NU series 16V 270µF (φ8×11.5L)
100
10
10
1
1
0.1
1
10
100
Frequency (kHz)
1000
10000
HS series 6.3V 390µF (φ8×6.7L)
SA series 6.3V 220µF (φ6.3×5.7L)
SL series 6.3V 220µF (φ6.3×4.2L)
100
10
0.1
1
0.1
1
10
100
1000
10000
10
100
1000
10000
10
100
1000
10000
Frequency (kHz)
100
10
1
1
0.1
1
10
100
Frequency (kHz)
1000
10000
VA series 16V 33µF (7.3×4.3×2.8)
UA series 16V 27µF (7.3×4.3×1.9)
Frequency (kHz)
100000
10000
ESR (mΩ)
10000
Impedance (mΩ)
1
1000
1000
100000
0.1
10000
ESR (mΩ)
Impedance (mΩ)
10000
100
1000
1000
100
100
10
10
0.1
1
10
100
Frequency (kHz)
1000
10000
Frequency (kHz)
NICHICON CORPORATION / FPCAP ELECTRONICS (SUZHOU) CO., LTD.
53
Technical Guide
Resistance to Soldering Heat
Test Condition : 260°C, 30sec
NS series 10V 220µF (φ10×12.5L)
NS series 16V 33µF (φ6.3×7L)
20
ΔC/C (%)
10
0
-10
ESR (Ω) at 100kHz
-20
0
1
2
3
4
5
0
1
2
3
4
5
10
1
0.1
0.01
Fevering Temperature by Ripple Current
L8 series 2.5V 560µF (φ8×8L)
R7 series 2.5V 820µF (φ8×11.5L)
R7 series 4.0V 820µF (φ10×12.5L)
VB series 2.0V 330µF (7.3×4.3×2.8)
o
Fevering Temperature ( C)
100
I2 R = ΔT× β×S= ΔTc×α×β×S
ΔTc = (I2 R) / (α×β×S)
log ΔTc = log (I2 R) / (αβS)
= log I2 + log R – log αβS
= 2×log I + (log R - log αβS)
10
1
1
10
Where,
I
: Ripple Current (Arms)
R : ESR (Ω)
ΔT : Fevering Temp. at Outside Wall of Capacitor (°C)
ΔTc : Fevering Temp. at Inside of Capacitor (°C)
β : Heat Radiation Coefficient (W/ °C×cm2)
S : Surface Area of Aluminum Case(cm2)
α : Ratio of ΔTc/ ΔT
Current (Arms)
54
NICHICON CORPORATION / FPCAP ELECTRONICS (SUZHOU) CO., LTD.
Technical Guide
Reliability at 105° C
NS series 6.3V 47µF (φ6.3×7L)
L8 series 2.5V 560µF (φ 8×8L)
NS series 4.0V 1200µF (φ10×12.5L)
VA series 16V 33µF (7.3×4.3×2.8)
Relative (%)
Change of Capacitance
High-temperature
lode
20
10
0
-10
-20
Absolute (tanδ)
10
100
Duration (H)
1000
10000
Duration (H)
1000
10000
Duration (H)
1000
10000
1000
10000
Change of Tangent of Loss Angle
0.15
0.1
0.05
0
10
Change of Leakage Current
1000
Absolute (μ A)
100
100
10
1
0.1
10
Change of Equivalent Series Resistance
100
Absolute (mΩ)
100
10
1
10
100
Duration (H)
NICHICON CORPORATION / FPCAP ELECTRONICS (SUZHOU) CO., LTD.
55
Estimating of Lifetime
Functional Polymer Aluminum Solid Electrolytic Capacitors
Calculation Formula of Lifetime
For
In general, calculation formula of lifetime of capacitors is appeared as follows.
The calculation formula of lifetime on FPCAP is same as usual Aluminum capacitor.
LX = L0×10(T0-TX)/20
Where,
LX (Hrs)
L0 (Hrs)
T0 (105°C)
TX (°C)
=Life expectance in actual use
=Life time
=Maximum operating temperature (105°C)
=Temperature of capacitor in actual use
On the other hand, temperature Tx adds the circumference temperature T as the capacitor temperature and the
generating temperature ΔT by ripple current.
TX=T+ΔT
T (°C) = Ambient temperature
ΔT (°C) = Generating temperature
There are two methods to calculate the heat rise (ΔT) of a capacitor by ripple current.
a) Measure the temperature of a capacitor in operation by means of fixing a thermocouple on the case
of a capacitor or other suitable methods.
The temperature difference between the temperature measured of the capacitor and the ambient
temperature is considered as the heat rise by ripple current.
b) The heat rise by ripple current is calculated by the following formula.
ΔT = ( I / I0 ) 2×ΔT0
I (A rms) = Ripple current in actual use
I0 (A rms) = Maximum permissible ripple current
ΔT0 (°C) = Generated temperature value by maximum permissible ripple current
[Aluminum Can Type: About 20°C, Molded Chip Type: About 10°C ]
Remark:<It is recommended to use the method of formula calculation during the design phase,
and use the method of actual measurement when checking as a set.>
56
NICHICON CORPORATION / FPCAP ELECTRONICS (SUZHOU) CO., LTD.
Application Guide
Functional Polymer Aluminum Solid Electrolytic Capacitors
DC/DC Converter Primary, Secondary Side Smoothing
Input side
3.3V
IC
For Primary
Side Smoothing
+3.3V CIRCUIT
+5V CIRCUIT
Output side
For Secondary
Side Smoothing
FPCAP 6.3V
5V
For Secondary
Side Smoothing
FPCAP 10∼6.3V
Back-up Capacitor for Variable Load (1)
12V
3.3∼5V
1.6∼1.8V
IC
IC
CPU
FPCAP 16V
FPCAP 6.3V
FPCAP 2.5∼4V
Back-up Capacitor for Variable Load (2)
3.3∼5V
1.6∼1.8V
IC
CPU
FPCAP 6.3V
FPCAP 2.5∼4V
Noise Filters
IC
IC
NICHICON CORPORATION / FPCAP ELECTRONICS (SUZHOU) CO., LTD.
57
Application Guide
Ripple Removal Capability
We measured ripple voltage by oscilloscope for output capacitor change on the
typical chopper type DC-DC converter. (described below)
VOUT=5V, IOUT=0.5A
f=100kHz
Oscilloscope
Electronic
Load
L
VIN=
12V
SW IC
D
C
Specimen
Comparison Between
Low Impedance Aluminum Capacitor
16V100uF (φ6.3×11L)
ΔV=156mV
and Other Capacitors with Same Capacitance
Low ESR Tantalum Capacitor
16V100uF (7.3×4.3×2.9)
ΔV=76mV
FPCAP
16V100uF (φ8×11.5L)
ΔV=58mV
Examination of Same Level Residual Ripple Voltage
To obtain same level of ripple voltage to FPCAP, Low Impedance Aluminum capacitor needs 16V3300uF,
even Low ESR tantalum capacitor needs 4 pcs. of same capacitance.
Low Impedance Aluminum Capacitor
16V3300uF (φ16×25L)
ΔV=60mV
58
Low ESR Tantalum Capacitor
16V100uF (7.3×4.3×2.9) × 4 pcs.
ΔV=59mV
NICHICON CORPORATION / FPCAP ELECTRONICS (SUZHOU) CO., LTD.
Application Guide
Spice Model for Simulation Circuits with Computer
Spice Model of Radial Lead Type (L8 and S8 series)
Part Number
Cp (μF)
Rs (mΩ)
L (nH)
LC (μA)
Rp (kΩ)
RL80E821MDN1
820
4.2
2.9
100
25
RL80G561MDN1
560
4.2
2.9
100
40
RL80J561MDN1
560
5.0
2.9
100
63
RS80E331MDN1
330
5.3
2.0
30
83
RS80E471MDN1
470
5.3
2.0
50
50
RS80E561MDN1
560
5.3
2.0
100
25
Typical ESL by Case Size
Classification
Radial Lead Type
SMD Type
Case Size (mm)
ESL (nH,40MHz)
φ6.3×8L (S8)
1.8 to 2.2
φ6.3×10L
2.8 to 3.0
φ8×8L (L8)
2.7 to 3.1
φ8×11.5L
3.9 to 4.1
φ8×11.5L (R7)
4.6 to 4.9
φ10×12.5L
5.4 to 5.6
φ4×5.2L
1.0 to 1.2
φ6.3×5.7L
2.5 to 2.7
φ8×11.7L
3.1 to 3.3
φ10×12.4L
4.5 to 4.7
7.3×4.3×1.9
1.3 to 1.5
7.3×4.3×2.8
1.6 to 1.8
Equivalent Circuit of Capacitor
Cp : Capacitance
Rp : Equivalent Parallel Resistance
Rp
Rs
L
(Insulation resistance) ( ≅Rated Voltage/LC)
Rs : Equivalent Series Resistance
L : Inductance
Cp
2
⎧
⎫ ⎧
Rp
ωCpRp 2 ⎫
Z = ⎨Rs +
⎬ + ⎨ωL −
⎬
1+ ω2Cp 2Rp 2 ⎭ ⎩
1+ ω2Cp 2Rp 2 ⎭
⎩
(
)
(
2
)
* It is available to present the spice model of other parts for customers.
NICHICON CORPORATION / FPCAP ELECTRONICS (SUZHOU) CO., LTD.
59
Memo
60
NICHICON CORPORATION / FPCAP ELECTRONICS (SUZHOU) CO., LTD.
Memo
NICHICON CORPORATION / FPCAP ELECTRONICS (SUZHOU) CO., LTD.
61
http://www.nichicon.co.jp/
http://www.nichicon.com
HEAD OFFICE
NICHICON (AMERICA) CORP.
Karasumadori Oike-agaru, Nakagyo-ku, Kyoto, 604-0845 Japan
TEL.81-75-231-8461 FAX.81-75-256-4158
927 East State Parkway, Schaumburg, Illinois 60173, U.S.A.
TEL.1-847-843-7500 FAX.1-847-843-2798
TOKYO SALES OFFICE
NICHICON (AUSTRIA) GmbH
5-5, 2-chome, Hamamatsu-cho, Minato-ku, Tokyo, 105-0013 Japan
TEL.81-3-5473-5611 FAX.81-3-5473-5651
Businesspark Marximum, Modecenterstrasse 17, Unit 2-7-A, 1110 Vienna, Austria
TEL.43-1-706-7932 FAX.43-1-706-7933
NAGOYA SALES OFFICE
•U.K.OFFICE
Coliseum Business Centre, Riverside Way, Camberley,
Surrey GU15 3YL, United Kingdom
TEL.44-1276-685393 FAX.44-1276-686531
18F Nishiki-Park Bldg. 4-3, Nishiki 2-chome, Naka-ku, Nagoya,
460-0003 Japan
TEL.81-52-223-5581 FAX.81-52-220-1839
NICHICON (HONG KONG) LTD.
WEST JAPAN SALES OFFICE
Karasumadori Oike-agaru, Nakagyo-ku, Kyoto, 604-0845 Japan
TEL.81-75-241-5370 FAX.81-75-231-8467
Unit 308, Harbour Centre Tower 1, 1 Hok Cheung Street,
Hunghom, Kowloon, Hong Kong
TEL.852-2363-4331 FAX.852-2764-1867
NICHICON (SINGAPORE) PTE. LTD.
FPCAP ELECTRONICS (SUZHOU) CO., LTD.
http://www.fpcap.jp
112 Sutong Road, Suzhou Industrial Park, Jiangsu, China 215021
TEL.86-512-6761-2423 FAX.86-512-6761-7076
NICHICON ELECTRONICS (SUQIAN) CO., LTD.
No.18 Yangmingshan Avenue, Suzhou Suqian Industrial Park, Suqian,
China 223800
TEL.86-527-8286-8855 FAX.86-527-8286-8966
20 Jalan Afifi, #06-08, Certis CISCO Centre Ⅱ, Singapore 409179
TEL.65-6481-5641 FAX.65-6481-6485
NICHICON (TAIWAN) CO., LTD.
16F-12, No.6, Sec.4, Hsin-Yi Rd., Taipei, Taiwan
TEL.886-2-2708-0200 FAX.886-2-2708-0959
NICHICON (THAILAND) CO., LTD.
Empire Tower 15th Floor, Unit 1506, Tower 3,
195 South Sathorn Road, Yannawa, Bangkok 10120, Thailand
TEL.66-2-670-0150 FAX.66-2-670-0153
NICHICON ELECTRONICS TRADING (SHANGHAI) CO., LTD.
Room 1206, Aetna Tower, 107 Zunyi Road, Shanghai, China 200051
TEL. 86-21-6237-5538 FAX. 86-21-6237-5537
•DALIAN REPRESENTATIVE OFFICE
12F Senmao Building, 147 Zhongshan Road, Xigang District, Dalian, China 116011
TEL.86-411-3989-3322 FAX.86-411-3989-3168
NICHICON ELECTRONICS TRADING (SHENZHEN) CO., LTD.
Room A, 16/F, KK100
No.5016, Shen Nan Road East, Luo Hu District, Shenzhen, China 518001
TEL.86-755-2294-1800 FAX.86-755-8294-5716
•CHONGQING BRANCH
Room 2812, 28/F, International Trade Center (Part A), No.38, Qing Nian Road,
Yuzhong District, Chongqing, China 400010
TEL.86-23-6310-8166 FAX.86-23-6310-8308
•CHENGDU BRANCH
Room 1408, 14/F, Hailrun Complex (Part A), No.216, Xi Dong Da Street, Jinjiang
District, Chengdu, Sichuan, China 610021
TEL.86-28-6212-9507 FAX.86-28-6212-9513
NICHICON ELECTRONICS (INDIA) PVT. LTD.
Level 9, Raheja Towers, 26-27 MG Road, Bangalore 560001, Karnataka, India
TEL.91-80-4180-0744 FAX.91-80-4180-0900
NICHICON (MALAYSIA) SDN. BHD.
No.4 Jalan P/10, Kawasan Perusahaan Bangi,
43650 Bandar Baru Bangi, Selangor Darul Ehsan, Malaysia
TEL.60-3-8925-0678 FAX.60-3-8925-0858
NICHICON ELECTRONICS (WUXI) CO., LTD.
Block 51-B, Wuxi National High & New Technology Industrial
Development Zone, Wuxi, Jiangsu, China 214028
TEL.86-510-8521-8222 FAX.86-510-8522-1170
CAUTION
FOR SAFETY
• TO USE NICHICON PRODUCT CORRECTLY AND SAFETY, PLEASE READ ”APPLICATION GUIDELINES”
VERY CAREFULLY.
• THE PRODUCTS ARE DESIGNED AND MANUFACTURED CHIEFLY FOR GENERAL ELECTRONIC
APPLIANCES. IN CASE THAT YOU ARE GOING TO APPLY THEM FOR MEDICAL EQUIPMENT,
AIRCRAFT / SPACE EQUIPMENT, OR THE SAME KIND THAT REQUIRES HIGH SAFETY, YOU ARE
REQUESTED TO CONFIRM THEIR ADAPTATION BEFORE THE USE.
• PRIOR TO ORDERING A PRODUCT, PLEASE OBTAIN A COPY OF SPECIFICATION FROM NICHICON
AND USE THE SPECIFICATION AS A BASIS WHEN DESIGNING EQUIPMENT AND INCORPORATING OUR
PRODUCT. NICHICON ADMITS NO LIABILITY FOR EQUIPMENT PROBLEMS DUE TO THE LACK OF
PRODUCT SPECIFICATIONS BEING CONFIRMED. ALSO, PLEASE BE SURE TO PERFORM ALL
NECESSARY UNIT LEVEL EVALUATION TESTING TO AVOID MALFUNCTIONS THAT COULD BE
UNFORESEEABLE DURING COMPONENT LEVEL TESTING ALONE.
NOTE: z SPECIFICATION AND DIMENSIONS IN THIS CATALOG ARE SUBJECT TO CHANGE WITHOUT NOTICE. IF NECESSARY, DRAWINGS CAN BE PROVIDED.
z IN CASE THAT THERE IS A CERTAIN DANGER OF THE PRODUCTS CONFLICTING WITH THE USE AND ACTIVITY FOR THE DEVELOPMENTS OF
WEAPONS OF MASS DESTRUCTION, THE PROCEDURES BASED UPON THE RELEVANT EXPORT REGULATIONLAWS ARE ABSOLUTELY NEEDED.
z THE PRODUCTS AND THEIR PACKAGES DO NOT CONTAIN ANY OZONE DEPLETING SUBSTANCES (ODS) UNDER THE MONTREAL PROTOCOL. AND
ODS IN NOT USED IN THEIR MANUFACTURING PROCESSES, TOO.
z OTHER THAN THE EXPRESS WRITTEN SPECIFICATIONS CONTAINED IN NICHICON'S CATALOG OR OTHER NICHICON LITERATURE. NICHICON MAKES
NO WARRANTY, EXPRESS, IMPLIED, OR OTHERWISE, INCONNECTION WITH THESE PRODUCTS, AND ALL IMPLIED WARRANTIES, INCLUDING THE
WARRANTY OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PRODUCT,ARE DISCLAIMED. NICHICON SHALL NOT BE LIABLE FOR INCIDENTAL
OR CONSEQUENTIAL DAMAGES.CUSTOMER'S SOLE REMEDY IN THE EVENT THAT NICHICON'S SPECIFICATIONS ARE NOT MET IS TO REPAIR,
REPLACE,OR REFUND THE PURCHASE PRICE OF THE SUBJECT PRODUCT, AT NICHICON'S OPTION
z CATALOG PRINTED IN DECEMBER. 1, 2012
©2013 NICHICON CORPORATION Printed in China