CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS S6 Miniature Sized, High Capacitance series Low ESR, High Capacitance, High ripple current. Miniature Sized. Load life of 2000 hours at 105°C. Radial lead type : Lead free flow soldering condition correspondence. Compliant to the RoHS directive (2011/65/EU). NE Higher Capacitance S6 Specifications Item Performance Characteristics Category Temperature Range –55 to +105°C Rated Voltage Range 2.5 to 25V Rated Capacitance Range 33 to 560µF Capacitance Tolerance ±20% at 120Hz, 20°C Tangent of loss angle (tan δ) Less than or equal to the specified value at 120Hz, 20°C ESR ( 1) Less than or equal to the specified value at 100kHz, 20°C Leakage Current ( 2) Less than or equal to the specified value. Endurance After 2 minutes' application of rated voltage at 20°C Test condition 105°C, rated voltage 2000Hrs. Capacitance change Within ±20% of initial value before test tan δ 150% or less than the initial specified value ESR( 1) 150% or less than the initial specified value Leakage current ( 2) Less than or equal to the initial specified value 1 ESR should be measured at both of the terminal ends closest to the capacitor body. 2 Conditioning : If any doubt arises, measure the leakage current after the voltage treatment of applying DC rated voltage continuously to the capacitor for 120 minutes at 105°C. [φ6.3×6] Size List Cap [µF] R.V.(V) S.V.( V) Aluminum case [φD×L(mm)] 2.5 10 16 25 2.8 11.5 18.4 28.7 33 Stand off Wire(Lead free) 6.3×5 56 6.3×5 100 6.3×6 6.3×5 150 390 6.3×5 560 6.3×5 [φ6.3×5 / φ6.3×6(-H)] Aluminum case Wire(Lead free) (mm) φd P α 6.3×5 0.5 2.5 1.0 6.3×6 0.45 2.5 1.0 φD×L Dimension table in next page. CAT.8100D CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS S6 series Standard Ratings Rated Voltage Surge Voltage (V) (V) (code) 2.5 (0E) 2.8 10 (1A) 11.5 16 (1C) 18.4 25 (1E) 28.7 Rated Capacitance (µF) Case Size φD×L (mm) tan δ Leakage Current (µA, 2min.) ESR (mΩ, 100kHz) Rated Ripple Current (mArms) NICHICON FPCAP 390 6.3×5 0.10 500 12 3500 RS60E391MCN1□□ FP-2R5RE391M-S6□□ 560 6.3×5 0.12 700 13 3600 RS60E561MCN1□□ FP-2R5RE561M-S6□□ 150 6.3×5 0.10 450 25 2500 RS61A151MCN1□□ FP-010RE151M-S6□□ 100 6.3×6 0.10 500 24 2490 RS61C101MDS1□□ FP-016RE101M-S6□□ 100 6.3×6 0.10 500 24 2490 RS61C101MCS1□□ FP-016RE101M-S6□□-H 33 6.3×5 0.10 165 60 1700 RS61E330MCN1□□ FP-025RE330M-S6□□ 56 6.3×5 0.10 280 30 2800 RS61E560MCN1□□ FP-025RE560M-S6□□ Frequency Characteristics (The frequency characteristics are typical and not a guaranteed value.) µ Impedance µ Frequency (kHz) Frequency (kHz) Taping specifications are given in page 26, 27. Please refer to page 3 for the minimum order quantity. CAT.8100D