LX - Nichicon

CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS
LX
Radial Lead Type, Long Life Assurance
series
High reliability, High voltage (to 50V).
Low ESR, High ripple current.
Long life of 3000 hours at 125°C.
Radial lead type:
Lead free flow soldering condition correspondence.
Adapted to the RoHS directive (2011/65/EU).
LX
Higher
Temperature
LV
Specifications
Item
Performance Characteristics
Category Temperature Range
– 55 to +125°C
Rated Voltage Range
16 to 50V
Rated Capacitance Range
22 to 390µF
Capacitance Tolerance
± 20%
Tangent of loss angle (tan δ)
Less than or equal to the specified value at 120Hz, 20°C
ESR (
Less than or equal to the specified value at 100kHz, 20°C
1)
Leakage Current (
2)
at 120Hz, 20°C
Less than or equal to the specified value.
.25
1
1.25
After 2 minutes' application of rated voltage at 20°C
Temperature Characteristics
(Max.Impedance Ratio)
Z+125°C / Z+20°C
Z– 55°C / Z+20°C
(100kHz)
Endurance
The specifications listed at below shall be met when the
capacitors are restored to 20°C after the rated voltage is
applied for 3000 hours at 125°C.
Damp Heat
(Steady State)
The specifications listed at below shall be met when the
capacitors are restored to 20°C after the rated voltage is
applied for 1000 hours at 60°C, 90% RH.
Resistance to
Soldering Heat
After soldering the capacitor under the soldering conditions
prescribed here as preheat at 150 to 200°C for 60 to 180 seconds
and peak temperature at 265°C for 10 seconds or less, the
capacitor shall meet the specifications listed at below, provided
that its temperature profile is measured at both of terminal ends
facing the soldering side.
Marking
Navy blue print on the case top
Capacitance change
tan δ
Within ± 20% of initial value ( 3)
150% or less of the initial specified value
150% or less of the initial specified value
Less than or equal to the initial specified value
Capacitance change
tan δ
Within ± 20% of initial value ( 3)
150% or less of the initial specified value
150% or less of the initial specified value
Less than or equal to the initial specified value
Capacitance change
tan δ
Within ± 10% of the initial capacitance value ( 3)
130% or less than the initial specified value
130% or less than the initial specified value
Less than or equal to the initial specified value
ESR ( 1)
Leakage current ( 2)
ESR ( 1)
Leakage current ( 2)
ESR ( 1)
Leakage current ( 2)
1 ESR should be measured at both of the terminal ends closest to the capacitor body.
2 Conditioning : If any doubt arises, measure the leakage current after the voltage treatment of applying DC rated voltage continuously to the capacitor for 120
minutes at 105°C.
3 Initial value : The value before test of examination of resistance to soldering.
Dimensions
Type numbering system (Example : 35V 39µF)
Resin coated Case
Capacitance
1
2
3
4
5
6
7
8
9
10 11
12
P L X 1 V 3 9 0 M C L 1
Size code
P±0.5
φD±0.5
LX
39
V
023
Voltage(V:35V)
Configuration
Capacitance tolerance (±20%)
Rated capacitance (39µF)
φd
Series
Lot. No.
L+0.5MAX.
15MIN
Rated voltage (35V)
4MIN
Series name
Type
Size
φD
L
P
φd
φ8 × 9L
8.0
8.5
3.5
0.6
(mm)
φ8 × 12L φ10 × 13L
8.0
10.0
11.5
12.5
3.5
5.0
0.6
0.6
Voltage
V
16
20
25
35
50
Code
C
D
E
V
H
Please refer to page 20 about the end seal configuration.
Dimension table in next page.
CAT.8100D
CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS
LX
series
Standard Ratings
Rated Voltage
(V)(code)
Surge Voltage
(V)
16
(1C)
18.4
20
(1D)
25
(1E)
35
(1V)
50
(1H)
23.0
28.7
40.2
57.5
Rated Ripple
(mArms)
Rated Capacitance
(µF)
Case Size
φD × L (mm)
tan δ
Leakage Current
(µA)
150
8×9
0.12
480
26
2100
810
PLX1C151MCL1
220
8 × 12
0.12
704
25
2400
930
PLX1C221MDL1
390
10 × 13
0.12
1248
23
2900
1130
PLX1C391MDL1
120
8×9
0.12
480
27
2000
800
PLX1D121MCL1
150
8 × 12
0.12
600
26
2300
910
PLX1D151MDL1
270
10 × 13
0.12
1080
24
2800
1110
PLX1D271MDL1
82
8×9
0.12
410
28
2000
780
PLX1E820MCL1
120
8 × 12
0.12
600
27
2300
890
PLX1E121MDL1
180
10 × 13
0.12
900
25
2800
1080
PLX1E181MDL1
39
8 ×9
0.12
273
33
1800
720
PLX1V390MCL1
56
8 × 12
0.12
392
31
2100
830
PLX1V560MDL1
100
10 × 13
0.12
700
28
2700
1040
PLX1V101MDL1
22
8×9
0.12
220
35
1800
700
PLX1H220MCL1
27
8 × 12
0.12
270
33
2000
810
PLX1H270MDL1
47
10 × 13
0.12
470
29
2600
1020
PLX1H470MDL1
Ambient temperature of a capacitor
ESR (mΩ)
(at 100kHz 20°C)
Part Number
Rated ripple current (mArms) at 105°C 100kHz
Please refer to page 20, 21, 22 about the formed or taped product spec.
Please refer to page 3 for the minimum order quantity.
CAT.8100D