2F-XSR

2F-XSR Series
FIXED INPUT,ISOLATED&REGULATED Single Output DC/DC Converter
SELECTION GUIDE
Input
FEATURES
Current(MA)
Efficiency
(%,Typ)
Switching
Frequency
(KHz,Typ)
Nominal
Range
Max
Min
2F0505SR
5
4.75-5.25
5
400
40
70
333
2F1205SR
12
11.4-12.6
5
400
40
70
58
2F2405SR
24
22.8-25.2
5
400
40
71
66
Voltage(VDC)
NOTICE:add Suffix “P” for Continuous Short Circuit Protection, e.g. IF0505XSP
◆
RoHS compliant
◆
Efficiency up to 84%
◆
SIP Package
◆
Output
Voltage
(VDC)
Order code
Wide temperature performance at full 2 Watt
load,-40°C to 85°C
◆
UL 94V-0 package material
◆
No heatsink required
◆
Low ripple and good EMC Features
◆
Industry standard pinout
ISOLATION SPECIFICATIONS
◆
Power sharing on output
◆
3KVDC isolation
◆
Continuous Short Circuit Protection
◆
Internal SMD construction
Parameter
Test conditions
Min.
Typ.
Max.
Units
Isolation test voltage
Flash tested for 1 minute and 1mA max
3000
VDC
Isolation resistance
Test at Viso=500VDC
1000
MΩ
Isolation capacitance
60
PF
No external components required
◆
◆
Good dynamic feature
MODEL SELECTION
①
②
③
④
⑤
⑥
2F 05 05 X S R
①Product Series
③Output Voltage
⑤SIP Package
②Input Voltage
④Fixed Input
⑥Regulated output
DESCRIPTION
The 2F-XSR series are specially designed
for applications where a group of polar power
supplies are isolated from the input power
supply in a distributed power supply system on
a circuit board.
These products apply to:
1) where the voltage of the input power supply
is fixed (voltage variation ≤±5%);
2) where isolation is necessary between input
and output (isolation voltage ≤3000VDC);
3) where the regulation of the output voltage
and the output ripple noise are demanded.
OUTPUT SPECIFICATIONS
Parameter
Test conditions
Output power
Min
Typ.
Max.
Units
2
W
Line regulation
For Vin change of ±5%
±0.5
%
Load regulation
10% to 100% full load
±1.5
%
100% full load
±3
%
Output voltage accuracy
Temperature drift
0.2
0.03
%/°C
Output Ripple*
20MHz Bandwidth
20
30
MV p-p
Output Noise*
20MHz Bandwidth
50
150
MV p-p
Full load,nominal input
100
Switching frequency
100% full load
Khz
* Test ripple and noise by "parallel cable" method.
See detailed operation instructions at Testing of Power Converter section, application notes.
MICRODC R ESERVES THE COPYRIGHT
http://www.microdc.cn
Technical Enquiries-Email:[email protected] Tel:0086-20-86000646
Page 1 of 2
2F-XSR Series
TEMPERATURE CHARACTERISTICS
Parameter
Conditions
Recommended circuit
Min.
Typ.
Storage humidity range
NO-load power consumption
Max.
Units
95
%
10
°C
Operating temperature
-40
85
°C
Storage temperature
-55
125
°C
Lead temperature
If you want to further decrease the input/output ripple,an
"LC"filtering network may be connected to the input and
output ends of the DC/DC converter. see (Figure 1).
1.5mm from case for 10 seconds
300
Temp.rise at full load
40
Cooling
58
°C
Free air convection
Case material
Plastic(UL94-V0)
IF-XSP
Short circuit protection
Continuous
1*
MTBF
3500
s
K hours
Weight
2.8
g
*Supply voltage must be discontinued at the end of short circuit duration.
TYPICAL CHARACTERISTICS
It should also be noted that the inductance and the
frequency of the "LC"filtering network should be
staggered with the DC/DC frequency to avoid mutual
interference.However, the capacitance of the output
filter capacitor must be proper. If the capacitance is too
big, a startup problem might arise. For every channel of
output,provided the safe and reliable operation is
ensured, the greatest capacitance of its filter capacitor
sees (Table 1).
EXTERNAL CAPACITOR TABLE (TABLE 1)
Cin
Vout
Vin
Temperature Derating Graph
(VDC)
5
Cout
(μF)
4.7
(VDC)
5
(μF)
4.7
12
2.2
-
-
24
0.47
-
-
It's not recommend to connect any external capacitor in
the application field with less than 0.5 watt output.
Overload Protection
Under normal operating conditions, the output circuit
of these products has no protection against over-current
and short-circuits.The simplest method is to connect a
self-recovery fuse in series at the input end or add a
circuit breaker to the circuit.
OUTLINE DIMENSIONS & PIN CONNECTIONS
IF-XS SIP7
SIZE Graph
Input Over-voltage Protection Circuit
RECOMMENDED FOOTPRINT
Top view,grid:2.54mm(0.1inch)
diameter:1.00mm(0.039inch)
The simplest device for input over-voltage protection is
a linear voltage regulator with overheat protection that is
connected to the input end in series(Figure 2).
When the environment temperature is higher than
71℃, the product output power should be less then
60% of the rated power.
FOOTPRINT DETAILS
Pin
1
Note:
Unit:mm(inch)
Pin section:0.50*0.3mm(0.020*0.012inch)
Pin section tolerances:±0.10mm(±0.004inch)
General tolerances:±0.25mm(±0.010inch)
2
4
6
Function
Vin
GND
0V
+V0
No parallel connection or plug and play.
Use dual output simultaneously, forbid opening
output pin (0V) to use as single output.
RoHS COMPLIANT INFORMATION
Microdc Professional Power Module,Inc.
Tel:0086-20-86000646
E-mail:[email protected]
Website:http://www.microdc.cn
This series is compatible with RoHS soldering systems with a peak wave solder temperature
of 300°C for 10 seconds.
The pin termination finish on the SIP package type is Tin Plate, Hot Dipped over Matte Tin
with Nickel Preplate. The DIP types are Matte Tin over Nickel Preplate. Both types in this
series are backward compatible with Sn/Pb soldering systems.
REACH COMPLIANT INFORMATION
This series has proven that this product does not contain harmful chemicals, it also has
harmful chemical substances through the registration, inspection and approval.
http://www.microdc.cn
Technical Enquiries-Email:[email protected] Tel:0086-20-86000646
Page 2 of 2