ALUMINUM ELECTROLYTIC 6.3V to 100V NEV, NEH SERIES SUBMINIATURE (NEV: Radial Lead, NEH: Axial Leads) MECHANICAL SPECIFICATIONS Lead Solderability: The NEV and NEH series subminiature aluminum electrolytic capacitors are especially suitable for applications requiring high capacitance, low cost, and very small size. In fact, you’ll find these capacitors in some of the most demanding applications, from precision medical electronics and automobiles to the newest personal computers and disk drives. They operate over a broad temperature range and are available in either blister pack or bulk. Meets the requirements of MIL−STD 202, Method 208 Marking: Consists of series type, nominal capacitance, rated voltage, temperature range, anode and/or cathode identification, vendor identification. Recommended Cleaning Solvents: Methanol, isopropanol ethanol, isobutanol, petroleum ether, propanol and/or commercial detergents. Halogenated hydrocarbon cleaning agents such as Freon (MF, TF, or TC), trichloroethylene, trichloroethane, or methylchloride are not recommended as they may damage the capacitor. RATINGS Capacitance Range: 0.1µf to 22,000µf Tolerance: ±20% Voltage Range: 6.3V to 100V CASE SIZE AND DIMENSIONS: PERFORMANCE SPECIFICATIONS Operating Temperature Range: −40°C to +85°C (−40°F to +185°F) Leakage Current: I ≤ 0.01CV + 3µA (measured after 3 minutes of applied voltage) I = Leakage Current (µA) C = Nominal Capacitance (µf) V = Rated Voltage (V) Capacitance Tolerance (M): ±20% measured at +20°C (+68°F), 120HZ Dissipation Factor: measured at +20°C (+68°F),120HZ Rated Voltage 6.3 10 16 25 35 50−80 100 0.1µf to 1000µf 0.24 0.2 0.17 0.15 0.12 0.10 0.08 1000µf to 22,000µf NEV SERIES Insulating Sleeve 18.0 Min Values above plus 0.02 for each 1000µf Comparison Z WV 6.3 10 16 25 35 50−100 4 Z @ −40°C (−40°F)/ Z @ +20°C (+68°F) 3 8 2 6 2 4 2 4 2 4 D’ Ø = D Ø + 0.5 Max 5.0 Min 4 L’ = L + 1.0 Max at D Ø ≤ 8.0 L 6.3 10 16 25 35 50 63 100 8 13 20 32 44 63 79 125 Surge Voltage dØ 2.3 Max DØ Leakage Current: Within values specified above Dissipation Factor: Within ±150% of specified value Capacitance Change Max: See Table Capacitance Change Max 6.3V to 16V Within ±30% of the initial value 25V to 100V Within ±20% of the initial value D’ Ø = D Ø + 0.5 Max L’ 35.0 Min L’ = L + 1.0 Max at D Ø ≤ 8.0 D’ Ø L’ = L + 2.0 Max at D Ø ≥ 10.0 ORDERING INFORMATION 47 M 50 Series Leakage Current: Within ±200% of specified value Dissipation Factor: Within ±150% of specified value Capacitance Change Max: Within ±20% of initial value Voice (973) 748−5089 35.0 Min NEV Shelf Life: 1000 Hrs @ +85°C (+185°F), no voltage applied NTE Electronics, Inc. L’ = L + 2.0 Max at D Ø ≥ 10.0 Insulating Sleeve Load Life: 1000 ±12Hrs @ +85°C (+185°F), at rated voltage Rated Voltage D’ Ø NEH SERIES (Insulating Bar = Negative) Surge Voltage: DC Rated Voltage DØ L L’ Z @ −25°C (−13°F)/ Z @ +20°C (+68°F) A ±0.5 dØ Impedance Ratio at Low Temperature: 120HZ Capacitance Tolerance Voltage FAX (973) 748−6224 http://www.nteinc.com 29 ALUMINUM ELECTROLYTIC 6.3V to 100V NEV Series (Radial Type) Dimensions: Diameter (D Ø) x Length (L): mm WV Cap (µf) 6.3 10 16 25 35 50 0.10 63 100 5 x 11 5 x 11 0.22 5 x 11 5 x 11 5 x 11 0.33 5 x 11 5 x 11 5 x 11 0.47 5 x 11 5 x 11 5 x 11 0.56 5 x 11 5 x 11 5 x 11 5 x 11 5 x 11 0.15 5 x 11 5 x 11 0.68 5 x 11 1.0 1.5 5 x 11 5 x 11 2.2 5 x 11 5 x 11 5 x 11 3.3 5 x 11 5 x 11 5 x 11 4.7 5 x 11 5 x 11 5 x 11 6.8 5 x 11 5 x 11 5 x 11 5 x 11 5 x 11 6.3 x 11 10 15 5 x 11 5 x 11 6.3 x 11 5 x 11 5 x 11 5 x 11 6.3 x 11 8 x 11.5 5 x 11 5 x 11 5 x 11 6.3 x 11 6.3 x 11 10 x 12.5 5 x 11 6.3 x 11 6.3 x 11 22 33 47 5 x 11 5 x 11 68 6.3 x 11 6.3 x 11 5 x 11 6.3 x 11 6.3 x 11 8 x 11 8 x 11 8 x 11.5 8.5 x 11 10 x 12 10 x 16 10 x 20 10 x 12.5 100 150 8 x 11.5 220 6.3 x 11 330 6.3 x 11 470 8 x 11 680 10 x 16 1000 1500 8 x 11.5 10 x 12.5 8 x 11.5 10 x 16 10 x 16 10 x 20 10 x 12.5 13 x 21 13 x 20 13 x 25 10 x 16 10 x 20 16 x 25 8 x 11.5 8 x 11.5 8 x 11.5 8 x 11.5 10 x 12.5 10 x 16 10 x 20 13 x 21 16 x 25 8 x 11.5 10 x 12.5 10 x 16 10 x 20 13 x 21 13 x 25 16 x 31.5 10 x 16 10 x 12.5 10 x 16 13 x 21 13 x 25 13 x 25 16 x 25 10 x 16 10 x 16 10 x 20 13 x 21 13 x 25 16 x 25 16 x 31.5 18 x 40 13 x 25 13 x 25 16 x 31.5 16 x 35.5 16 x 35.5 2200 13 x 21 13 x 21 13 x 25 16 x 25 16 x 31.5 18 x 36 18 x 40 3300 13 x 21 13 x 25 16 x 25 16 x 31.5 18 x 36 18 x 40 22 x 41 4700 16 x 25 16 x 25 16 x 31.5 18 x 36 18 x 40 22 x 41 6800 16 x 25 16 x 31.5 18 x 36 18 x 40 22 x 41 16 x 31.5 18 x 36 18 x 40 22 x 41 10000 22000 6.3 x 11 8 x 11.5 8 x 11.5 18 x 46 * These dimensions are for reference only, please consult the factory for actual size. NEV Series (Radial Type) Mechanical Specifications: mm Outside Diameter (D Ø) 5 6.3 8 10 13 16 18 Lead Spacing (A) 2 2.5 3.5 5 5 7.5 7.5 10 0.5 0.6 0.6 0.6 0.6 0.8 0.8 1.0 Lead Diameter (d Ø) 22 * These dimensions are for reference only, please consult the factory for actual size. 30 NTE Electronics, Inc. Voice (973) 748−5089 FAX (973) 748−6224 http://www.nteinc.com ALUMINUM ELECTROLYTIC 6.3V to 100V NEH Series (Axial Type) Dimensions: Diameter (D Ø) x Length (L): mm WV Cap (µf) 6.3 10 16 25 35 50 63 100 0.10 5 x 12.5 5 x 12.5 0.22 5 x 12.5 5 x 12.5 5 x 12.5 0.33 5 x 12.5 5 x 12.5 5 x 12.5 0.47 5 x 12.5 5 x 12.5 5 x 12.5 0.68 5 x 12.5 1.0 5 x 12.5 1.5 5 x 12.5 5 x 12.5 5 x 11 2.2 5 x 12.5 5 x 12.5 5 x 12.5 3.3 5 x 12.5 5 x 12.5 5 x 12.5 4.7 5 x 12.5 5 x 12.5 5 x 12.5 6.8 5 x 11 10 6.3 x 12.5 5 x 11 6.3 x 12.5 6.3 x 11 6.3 x 12.5 15 5 x 11 5 x 11 6.3 x 11 6.3 x 11 8 x 11.5 22 5 x 11 6.3 x 12.5 6.3 x 12.5 6.3 x 16 8 x 16 8 x 20 5 x 12 6.3 x 12.5 6.3 x 12.5 6.3 x 16 8 x 16 8 x 16 8 x 20 6.3 x 12.5 6.3 x 12.5 6.3 x 16 8 x 16 8 x 16 8 x 20 10 x 20 8 x 11.5 8 x 16 8 x 16 10 x 12.5 10 x 16 33 47 5 x 11 68 6.3 x 11 6.3 x 11 100 6.3 x 12.5 6.3 x 16 6.3 x 16 8 x 16 8 x 20 8 x 20 10 x 20 150 8 x 16 8 x 16 8 x 16 10 x 16 10 x 16 10 x 16 10 x 20 220 8 x 16 8 x 16 8 x 16 8 x 20 10 x 20 10 x 20 10 x 25 330 8 x 16 8 x 16 8 x 20 10 x 20 10 x 20 13 x 25 13 x 25 470 8 x 16 8 x 20 10 x 20 10 x 20 10 x 25 13 x 25 13 x 30 16 x 30 680 10 x 16 10 x 20 10 x 20 10 x 25 13 x 25 13 x 30 16 x 30 16 x 30 1000 10 x 20 10 x 20 13 x 25 13 x 25 13 x 30 16 x 30 16 x 30 18 x 40 1500 13 x 25 13 x 25 13 x 20 16 x 31.5 2200 10 x 25 13 x 25 13 x 30 16 x 25 16 x 30 18 x 40 22 x 40 3300 13 x 25 13 x 30 16 x 30 16 x 30 16 x 40 22 x 40 22 x 50 4700 16 x 30 16 x 30 16 x 40 18 x 40 22 x 40 22 x 50 6800 16 x 30 16 x 40 18 x 40 22 x 40 22 x 50 10000 16 x 30 18 x 40 22 x 40 22 x 50 22000 10 x 25 13 x 25 25 x 50 * These dimensions are for reference only, please consult the factory for actual size. NEH Series (Axial Type) Mechanical Specifications: mm Outside Diameter (D Ø) Lead Diameter (d Ø) 5 6.3 8 10 13 16 18 22 25 0.6 0.6 0.6 0.6 0.8 0.8 0.8 0.8 0.8 * These dimensions are for reference only, please consult the factory for actual size. NTE Electronics, Inc. Voice (973) 748−5089 FAX (973) 748−6224 http://www.nteinc.com 31 ALUMINUM ELECTROLYTIC 160V to 450V NEVH, NEHH SERIES SUBMINIATURE HIGH VOLTAGE (NEVH: Radial Lead, NEHH: Axial Leads) MECHANICAL SPECIFICATIONS The NEVH and NEHH series subminiature aluminum electrolytic capacitors are ideal for polarized capacitor applications requiring small size, high capacitance, high voltage, low cost, and dependability over broad temperature ranges. RATINGS Capacitance Range: 1.0µf to 470µf Tolerance: −10%, +75% Voltage Range: 160V to 450V PERFORMANCE SPECIFICATIONS Operating Temperature Range: • For 160V and 250V: −40°C to +85°C (−40°F to +185°F) • For 350V and 450V: −25°C to +85°C (−13°F to +185°F) Leakage Current: I ≤ 0.02CV + 100µA (measured after 3 minutes of applied voltage) I = Leakage Current (µA) C = Nominal Capacitance (µf) V = Rated Voltage (V) Capacitance Tolerance (M): at +20°C (+68°F), 120HZ Capacitance Values through 4.7µf −10% to +75% Capacitance Values above 4.7µf −10% to +50% Dissipation Factor: at +20°C (+68°F),120HZ Rated Voltage 160, 250, and 350 450 0.20 0.25 1.0µf to 470µf Lead Solderability: Meets the requirements of MIL−STD 202, Method 208 Marking: Consists of series type, nominal capacitance, rated voltage, temperature range, anode and/or cathode identification, vendor identification. Recommended Cleaning Solvents: Methanol, isopropanol ethanol, isobutanol, petroleum ether, propanol and/or commercial detergents. Halogenated hydrocarbon cleaning agents such as Freon (MF, TF, or TC), trichloroethylene, trichloroethane, or methylchloride are not recommended as they may damage the capacitor. CASE SIZE AND DIMENSIONS: NEVH SERIES Insulating Sleeve 18.0 Min Impedance Ratio at Low Temperature: 120HZ Comparison Z WV Z @ −25°C (−13°F)/ Z @ +20°C (+68°F) Z @ −40°C (−40°F)/ Z @ +20°C (+68°F) 160−250 350 450 2 2 2 − − DC Rated Voltage 160 250 350 450 Surge Voltage 200 300 400 500 D’ Ø L’ = L + 1.0 Max at D Ø ≤ 8.0 L’ = L + 2.0 Max at D Ø ≥ 10.0 NEHH SERIES (Insulating Bar = Negative) L Load Life: 1000 ±12Hrs @ +85°C (+185°F), at rated voltage Leakage Current: Within values specified above Dissipation Factor: Within ±200% of specified value Capacitance Change Max: See Table 160V to 450V 5.0 Min D’ Ø = D Ø + 0.5 Max Surge Voltage: Rated Voltage DØ L L’ 4 A ±0.5 dØ Insulating Sleeve dØ 2.3 Max DØ 35.0 Min L’ 35.0 Min D’ Ø Capacitance Change Max D’ Ø = D Ø + 0.5 Max Within 20% of the initial value Shelf Life: 1000 Hrs @ +85°C (+185°F), no voltage applied Leakage Current: Within ±200% of specified value Dissipation Factor: Within ±150% of specified value Capacitance Change Max: Within ±20% of initial value L’ = L + 1.0 Max at D Ø ≤ 8.0 L’ = L + 2.0 Max at D Ø ≥ 10.0 ORDERING INFORMATION NEVH 47 M 160 Series Capacitance Tolerance Voltage 32 NTE Electronics, Inc. Voice (973) 748−5089 FAX (973) 748−6224 http://www.nteinc.com ALUMINUM ELECTROLYTIC 160V to 450V NEVH Series (Radial Type) Dimensions: Diameter (D Ø) x Length (L): mm WV 160 250 1.0 6.3 x 11 6.3 x 11 2.2 6.3 x 11 Cap (µf) 350 450 8 x 11.5 8 x 11.5 10 x 12.5 10 x 12.5 10 x 16 3.3 8 x 11.5 10 x 12.5 10 x 16 10 x 20 4.7 8 x 11.5 10 x 12.5 10 x 16 13 x 20 10 10 x 12.5 10 x 20 13 x 21 13 x 25 22 10 x 20 13 x 25 13 x 25 16 x 31.5 33 13 x 21 13 x 25 16 x 31.5 18 x 35.5 47 13 x 25 16 x 25 18 x 36 22 x 35 100 16 x 25 18 x 36 22 x 35 25 x 40 220 18 x 35 330 22 x 35 470 22 x 40 * These dimensions are for reference only, please consult the factory for actual size. NEVH Series (Radial Type) Mechanical Specifications: mm Outside Diameter (D Ø) 6.3 8 10 13 16 18 22 25 Lead Spacing (A) 2.5 3.5 5 5 7.5 7.5 10 12.5 Lead Diameter (d Ø) 0.5 0.6 0.6 0.6 0.8 0.8 0.8 1.0 * These dimensions are for reference only, please consult the factory for actual size. NEHH Series (Axial Type) Dimensions: Diameter (D Ø) x Length (L): mm WV 160 Cap (µf) 250 350 450 1.0 6.3 x 16 8 x 16 8 x 16 10 x 20 2.2 8 x 16 8 x 20 10 x 20 10 x 20 3.3 8 x 16 10 x 20 10 x 20 10 x 20 4.7 8 x 20 10 x 20 10 x 20 13 x 25 10 10 x 25 10 x 20 13 x 25 13 x 30 22 10 x 20 13 x 25 13 x 30 16 x 30 33 13 x 25 13 x 30 16 x 30 16 x 40 47 13 x 30 16 x 30 16 x 40 16 x 40 100 16 x 30 16 x 40 18 x 40 22 x 40 220 22 x 40 330 25 x 52 470 22 x 52 * These dimensions are for reference only, please consult the factory for actual size. NEHH Series (Axial Type) Mechanical Specifications: mm Outside Diameter (D Ø) 6.3 8 10 13 16 18 22 25 Lead Diameter (d Ø) 0.6 0.6 0.6 0.8 0.8 0.8 0.8 0.8 * These dimensions are for reference only, please consult the factory for actual size. NTE Electronics, Inc. Voice (973) 748−5089 FAX (973) 748−6224 http://www.nteinc.com 33