ULTRA MINIATURE ALUMINUM ELECTROLYTIC ULM SERIES 5mm ULTRA MINIATURE (Radial Lead, 105 C Max) MECHANICAL SPECIFICATIONS Marking: NTE’s ULM series of ultra miniature aluminum electrolytic capacitors are designed for use in general purpose applications. These high temperature, radial lead capacitors are especially suitable for applications that require small− size, extended life, and higher temperature operation. Consists of series type, nominal capacitance, rated voltage, temperature range, anode and/or cathode identification, vendor identification. RATINGS Recommended Cleaning Solvents: Capacitance Range: 0.1 f to 470 f Tolerance: Methanol, isopropanol ethanol, isobutanol, petroleum ether, propanol and/or commercial detergents. Halogenated hydrocarbon cleaning agents such as Freon (MF, TF, or TC), trichloroethylene, trichloroethane, or methylchloride are not recommended as they may damage the capacitor. 20% Voltage Range: 6.3V to 50 Volts PERFORMANCE SPECIFICATIONS Operating Temperature Range: -40 C to +105 C (-40 F to +220.9 F) 6.3V to 50V: Leakage Current: 6.3V to 50V: CASE SIZE AND DIMENSIONS: 0.01CV (+3 A) 20% (M) Capacitance Tolerance: measured at +20 C (+68 F), 120HZ Dissipation Factor: measured at +20 C (+68 F),120HZ Working Voltage (VDC) 6.3 16 35 50 0.1 f to 470 f 28 20 14 12 Impedance Ratio at Low Temperature: 120HZ Working Voltage (VDC) 6.3 16 35 50 Z @ −25 C (−13 F)/ Z @ +20 C (+68 F) 4 2 2 2 Z @ −40 C (−40 F)/ Z @ +20 C (+68 F) 8 4 4 4 Rubber End Seal Sleeve Ripple Current: The ripple current multipliers (See Table) adjust the current to make the capacitors operating temperature the same for different ambient temperatures and ripple frequencies. CAP ( F)/Hz Multiplier 50 (60) 120 1K 10K 0.1 to 47 0.8 1.0 1.30 1.50 56 and up 0.8 1.0 1.15 1.20 Temperature 40 C 65 C 85 C 105 C Multiplier 2.0 1.6 1.25 1.00 Load Life: 1000 Hrs @ +105 C (+220.9 F), at Rated DC voltage applied Shelf Life: 1000 Hrs @ +105 C (+220.9 F), no voltage applied NTE Electronics, Inc. Voice (973) 748−5089 15.0 Min A 0.5 dØ 5.0 Min L 1.5 Max DØ ORDERING INFORMATION ULM 10 M 16 Series Capacitance Tolerance Voltage FAX (973) 748−6224 http://www.nteinc.com 41 ULTRA MINITURE ALUMINUM ELECTROLYTIC ULM SERIES ULM Series Dimensions: Diameter (D Ø) x Length (L): mm WV 6.3 Cap ( f) 16 35 50 0.1 3x5 0.22 3x5 0.33 3x5 0.47 3x5 1.0 3x5 2.2 3x5 3.3 4x5 4.7 4x5 10 3x5 5x5 6x5 22 4x5 6x5 6x5 8x5 33 4x5 5x5 6x5 47 4x5 5x5 6x5 68 5x5 6x5 100 5x5 6x5 220 6x5 8x5 330 8x5 470 8x5 * These dimensions are for reference only, please consult the factory for actual size. ULM Mechanical Specs: Dimensions (mm) Outside Diameter Lead Spacing Lead Wire DØ 3.0 4.0 5.0 6.0 8.0 A 1.0 0.5 1.5 0.5 2.0 0.5 2.5 0.5 3.5 0.5 dØ 0.45 0.45 0.45 0.45 0.45 * These dimensions are for reference only, please consult the factory for actual size. 42 NTE Electronics, Inc. Voice (973) 748−5089 FAX (973) 748−6224 http://www.nteinc.com