Constant current LED Drivers For outdoor use LGU-30C Series, 30 Watt FEATURES: Constant current output Universal AC input: 90-305VAC Active power factor correction Short circuit, over voltage, over temperature protections Designed to worldwide safety standards for lighting Cooling by free air convection 5 year warranty Model Nominal Input voltage (Vac) LGU30-C350 LGU30-C450 LGU30-C700 100-277 LGU30-C1050 Output current (mA) Output voltage (Vdc) Output power (W) Min. Max. 350 52 86 30 450 40 67 30 700 26 43 30 1050 17 29 30 Note: 1. Other output models may available on request; 2. Add suffix for dimming option, “D” (0~10V), “P” (PWM), “T” (Timer). ELECTRICAL Input Parameters Symbols Test Conditions / Comment Min. Typ. Max. Units Input voltage Vin -- 90 -- 305 Vac Input frequency Fline -- 47 -- 63 Hz Full load, Vin = 110Vac -- 0.33 -- A Full load, Vin = 220Vac -- 0.16 -- A Cold start, Vin = 230Vac -- -- 24 A Full load, Vin = 110Vac -- 0.99 -- PF Full load, Vin = 220Vac -- 0.95 -- PF Full load, Vin = 110Vac 83 -- 86 % Full load, Vin = 220Vac 84 -- 88 % Vin = 264Vac, 50Hz -- -- 0.35 A Input current Inrush current Power factor Efficiency Leakage current www.pairuigroup.com Iin Iinrush PF η Ileakage Page: 1 / 5 Date: 01/20/2015 *Subject to change without prior notice. Constant current LED Drivers For outdoor use LGU-30C Series, 30 Watt ELECTRICAL Output Parameters Output current accuracy No load output voltage Symbols Test Conditions / Comment Min. Typ. Max. Units -- -- -- 5 -- % LGU30-C350 -- -- 95 V LGU30-C450 -- -- 74 V LGU30-C700 -- -- 48 V LGU30-C1050 -- -- 32 V VNO-Load Line regulation Iout-line Vin from 90Vac to 305Vac -- -- 5 % Load regulation Iout-load Vout from min. to max. -- -- 5 % Turn-on delay time Ton_delay Cold start, power on -- -- 2 S -- -- -- 20 -- % Ripple Protection Over voltage 115~150% rated output voltage. In latch mode, the power supply shall return to normal operation only after the power is turned on again. Short circuit In hiccup mode, it will recover automatically after fault condition is removed. Over temperature Typ. 110 ℃ Environment Storage Ambient operating temperature Maximum case temperature Operating relative humidity MTBF Dimension(LxWxH) Tstorage Humidity: 5% RH to 100% RH -40 -- +85 ℃ Ta Startup at rated voltage -40 -- +70 ℃ Tc Hot-spot on case -- -- +80 ℃ Ha Non condensing 10 -- 95 % -- 400 -- kHrs TMTBF Full load, 220Vac input, ℃ 25 ambient temperature 145 x 43.5 x 34.5mm Weight www.pairuigroup.com 300g Page: 2 / 5 Date: 01/20/2015 *Subject to change without prior notice. Constant current LED Drivers For outdoor use LGU-30C Series, 30 Watt ELECTRICAL Safety / EMC Safety standards UL8750, UL935, UL1012, UL1310 CLASS 2, EN61347-1, EN61347-2-13 EN55015, FCC Part 15 Class B, EN61000-3-2, EN61000-3-3, EN61000-4-2, 3, 4, 6, 8, 11, EMC EN61547 ℃ and Notes: Unless otherwise specified, all the above parameters are measured at ambient temperature of 25 Vin = 100Vac to 277Vac. MECHANICAL Unit: mm ELECTRICAL CURVE DERATING CURVE www.pairuigroup.com STATIC CHARACTERISTIC CURVE Page: 3 / 5 Date: 01/20/2015 *Subject to change without prior notice. Constant current LED Drivers For outdoor use LGU-30C Series, 30 Watt DIMMING FUNCTION 0~10V Dimming External Resistor Dimming ITEM Conditions Value Maximum Voltage Normally 10~11V 0~12V 0-10V Input Current -- 0~10mA 10V Output Voltage Normally 11V 10~12V 10V Output Current -- 10mA Max. Note: 1. To make the driver operate properly, the load voltage must be controlled above the minimum voltage which close to 50% of the maximum output voltage is from any given mode. 2. The dimming signal can be less than 1V. As it is for 0-1V ,the output current can maintain 10% of the rated output current, but the connected LEDs may flicker. It's strongly recommended that keep dimming voltage bigger than 1V. 3. It is not allowed to connect the GND of dimming to the output, or the LED driver can not work as normal. www.pairuigroup.com Page: 4 / 5 Date: 01/20/2015 *Subject to change without prior notice. Constant current LED Drivers For outdoor use LGU-30C Series, 30 Watt DIMMING FUNCTION PWM Dimming ITEM Conditions Value Input Voltage -- 1-10V Input Current -- 10mA PWM Frequency -- 0.5-3KHz PWM Pulse Width -- 0~100% Timer Dimming Note: Above table for Timer dimming is just for reference, it can be adjusted according to the customer's requirements. www.pairuigroup.com Page: 5 / 5 Date: 01/20/2015 *Subject to change without prior notice.