Constant current LED Drivers For outdoor use LGU-60C Series, 60 Watt FEATURES: Constant current output Universal AC input: 90-305VAC Active power factor correction Short circuit, over voltage, over temperature protections Designed to worldwide safety standards for lighting Cooling by free air convection 5 year warranty Model Nominal Input voltage (Vac) Output current (mA) Output voltage (Vdc) Output power (W) Min. Max. LGU60-C350 350 102 171 60 LGU60-C450 450 80 133 60 LGU60-C700 700 52 85 60 1050 34 57 60 LGU60-C1400 1400 26 43 60 LGU60-C1750 1750 20 34 60 LGU60-C2100 2100 17 28 60 LGU60-C1050 100-277 Note: 1. Add suffix for dimming option, “D” (0~10V), “P” (PWM), “T” (Timer); 2. Add suffix for package option, blank(default), “W” or “L”. See mechanical specifications. ELECTRICAL Input Parameters Symbols Test Conditions / Comment Min. Typ. Max. Units Input voltage Vin -- 90 -- 305 Vac Input frequency Fline -- 47 -- 63 Hz Input current Iin Full load, Vin = 230Vac -- 0.32 -- A Inrush current Iinrush Cold start, Vin = 230Vac -- 65 -- A Power factor PF 70%~100% load, Vin = 230Vac -- 0.95 -- PF η Full voltage, full load -- 0.85 -- % Efficiency www.pairuigroup.com Page: 1 / 5 Date: 03/11/2015 *Subject to change without prior notice. Constant current LED Drivers For outdoor use LGU-60C Series, 60 Watt ELECTRICAL Output Parameters Output current accuracy No load out voltage Symbols Test Conditions / Comment Min. Typ. Max. Units -- -- -- 5 -- % LGU60-C350 -- -- 222 V LGU60-C450 -- -- 173 V LGU60-C700 -- -- 110 V LGU60-C1050 -- -- 74 V LGU60-C1400 -- -- 60 V LGU60-C1750 -- -- 44 V LGU60-C2100 -- -- 40 V VNO-Load Line regulation Iout-line Vin from 90Vac to 305Vac -- -- 1 % Load regulation Iout-load Vout from min. to max. -- -- 3 % Iover-shoot Turning power on -- -- 10 % Ton_delay Cold start, power on -- -- 2 S -- -- -- 20 -- % Output Current overshoot Turn-on delay time Ripple Protection Over voltage 115~150% rated output voltage. In latch mode, the power supply shall return to normal operation only after the power is turned on again Short circuit In hiccup mode, it will recover automatically after fault condition is removed Over temperature Typ. 110 ℃ Environment Storage Ambient operating temperature Maximum case temperature Operating relative humidity MTBF www.pairuigroup.com Tstorage Humidity: 5% RH to 95% RH -40 -- +85 ℃ Ta Startup at rated voltage -35 -- +70 ℃ Tc Hot-spot on case -- -- +80 ℃ Ha Non condensing 10 -- 95 % -- 200 -- kHrs TMTBF Full load, 220Vac input, ℃ 25 ambient temperature Page: 2 / 5 Date: 03/11/2015 *Subject to change without prior notice. Constant current LED Drivers For outdoor use LGU-60C Series, 60 Watt ELECTRICAL Dimension(LxWxH) W: 177x65.5x39.5mm Weight 745g Safety / EMC Safety standards EMC UL8750, UL935, UL1012, UL1310 CLASS 2, EN61347-1, EN61347-2-13 EN55015, FCC Part 15 Class B, EN61000-3-2, EN61000-3-3, EN61000-4-2, 3, 4, 6, 8, 11, EN61547 Notes: Unless otherwise specified, all the above parameters are measured at ambient temperature of 25 Vin = 100Vac to 277Vac. ℃ and MECHANICAL PACKAGE TYPE “W” Unit: mm www.pairuigroup.com Page: 3 / 5 Date: 03/11/2015 *Subject to change without prior notice. Constant current LED Drivers For outdoor use LGU-60C Series, 60 Watt ELECTRICAL CURVE DERATING CURVE STATIC CHARACTERISTIC CURVE DIMMING FUNCTION 0~10V Dimming External Resistor Dimming ITEM Conditions Value Maximum Voltage Normally 10~11V 0~12V 0-10V Input Current -- 0~10mA 10V Output Voltage Normally 11V 10~12V 10V Output Current -- 10mA Max. www.pairuigroup.com Page: 4 / 5 Date: 03/11/2015 *Subject to change without prior notice. Constant current LED Drivers For outdoor use LGU-60C Series, 60 Watt DIMMING FUNCTION Note: 1. To make the driver operate properly, the load voltage must be controlled above the minimum voltage which close to 50% of the maximum output voltage is from any given mode. 2. The dimming signal can be less than 1V. As it is for 0-1V ,the output current can maintain 10% of the rated output current, but the connected LEDs may flicker. It's strongly recommended that keep dimming voltage bigger than 1V. 3. It is not allowed to connect the GND of dimming to the output, or the LED driver can not work as normal. PWM Dimming ITEM Conditions Value Input Voltage -- 1-10V Input Current -- 10mA PWM Frequency -- 0.5-3KHz PWM Pulse Width -- 0~100% Timer Dimming Note: Above table for Timer dimming is just for reference, it can be adjusted according to the customer's requirements. www.pairuigroup.com Page: 5 / 5 Date: 03/11/2015 *Subject to change without prior notice.