P18TG-xxxxE/Z2:1(H35)MLF PMD-SERIES Rev.11-2008 4 Watt Regulated DIP24 Metal Case 1.5 to 3.5 kV DC I/O Isolation SINGLE and DUAL Output Continuous Short Circuit Prot. Full SMD Technology Mainzer Straße 151–153 D-55299 Nackenheim Tel. +49 6135 7026-0 Fax: +49 6135 931070 www.peak-electronics.de [email protected] The PMD 4W series P18TG-xxxxE/Z2:1(H35)MLF is a family of cost effective 4W single & dual output DC-DC converters. These converters are encapsulated in miniature DIP24 metal case. High performance features: 1500VDC up to 3500VDC input/output isolation, continuous short circuit protection with automatic restart and tight line / load regulation, high efficiency operation, output voltage accuracy of ±1% maximum and a wide input range of 2:1 All specifications typical at Ta=25°C, nominal input voltage and full load unless otherwise specified Input Specifications Voltage Range Input Filter Input Reflected Ripple Current¹ 2:1 Wide Input Pi Type 35 mA pk-pk Output Specifications Voltage Accuracy Short Circuit Protection Line Regulation Load Regulation Ripple and Noise (20Mhz bandwidth) Temperature Coefficient ± 1% Indefinite (automatic recovery) ± 0.5% ± 0.5% (3.3 / ± 3.3Vout Models: ± 1.5%) 60 mV pk-pk ± 0.02% / °C General Specifications Efficiency I/O Isolation Voltage (3 sec.) I/O Isolation Capacity I/O Isolation Resistance Switching Frequency (typical) Humidity Reliability Calculated MTBF (MIL-HDBK-217F) See Table 1500 VDC (3500 VDC optional)* 470 pF, typ. 1000 MOhm 266 kHz 95% rel H > 1.121 Mhrs Physical Specifications Case Material Potting Material Weight Nickel Coated Copper Epoxy (UL94V-0 rated) ~ 17g, typ. Environment Specifications Operating Temperature Maximum Case Temperature Storage Temperature Cooling RoHS Conform -40 to +85°C (ambient) 100°C -40 to +125°C Free Air Convection Soldering 260°C, max. (1.5mm from case 10s.) PMD-Series – P18TG-xxxxE/Z2:1(H35)MLF – Single and Dual Output – DIP24 - Metal Case Specification can change without a notice – We accept no liability for any inaccuracy or printing errors. Page 1/3 Selection Guide Single/Dual Output Order # A) ) ) mA) d (m ad ( (mA ad (mA a o ) o d L L a C ) o (uF) ll L n. D C Lo d² t Mi t Fu (VD F u ll e (V No a ) n n t g t e o e e n a n % r r g t L ( r r y rre rre lta or Cu Vol Cu acit ienc t Vo t Cu put Cu pu t put pu t Cap In p u Inpu In O ut O ut Out E ffic SINGLE OUTPUT P18TG-123R3E2:1MLF P18TG-1205E2:1MLF P18TG-1209E2:1MLF P18TG-1212E2:1MLF P18TG-1215E2:1MLF P18TG-1224E2:1MLF P18TG-243R3E2:1MLF P18TG-2405E2:1MLF P18TG-2409E2:1MLF P18TG-2412E2:1MLF P18TG-2415E2:1MLF P18TG-2424E2:1MLF P18TG-483R3E2:1MLF P18TG-4805E2:1MLF P18TG-4809E2:1MLF P18TG-4812E2:1MLF P18TG-4815E2:1MLF P18TG-4824E2:1MLF 9-18 9-18 9-18 9-18 9-18 9-18 18-36 18-36 18-36 18-36 18-36 18-36 36-72 36-72 36-72 36-72 36-72 36-72 30 30 30 30 30 30 20 20 20 20 20 20 15 15 15 15 15 15 463 428 428 417 417 417 223 209 209 201 209 196 112 105 102 105 103 102 3.3 5 9 12 15 24 3.3 5 9 12 15 24 3.3 5 9 12 15 24 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1200 800 444 333 266 166 1200 800 444 333 266 166 1200 800 444 333 266 166 72 78 78 80 80 80 75 80 80 83 80 85 75 80 82 80 81 82 3300 1000 470 220 100 47 3300 1000 470 220 100 47 3300 1000 470 220 100 47 DUAL OUTPUT P18TG-123R3Z2:1MLF P18TG-1205Z2:1MLF P18TG-1209Z2:1MLF P18TG-1212Z2:1MLF P18TG-1215Z2:1MLF P18TG-1224Z2:1MLF P18TG-243R3Z2:1MLF P18TG-2405Z2:1MLF P18TG-2409Z2:1MLF P18TG-2412Z2:1MLF P18TG-2415Z2:1MLF P18TG-2424Z2:1MLF P18TG-483R3Z2:1MLF P18TG-4805Z2:1MLF P18TG-4809Z2:1MLF P18TG-4812Z2:1MLF P18TG-4815Z2:1MLF P18TG-4824Z2:1MLF 9-18 9-18 9-18 9-18 9-18 9-18 18-36 18-36 18-36 18-36 18-36 18-36 36-72 36-72 36-72 36-72 36-72 36-72 30 30 30 30 30 30 20 20 20 20 20 20 15 15 15 15 15 15 452 428 417 417 417 421 226 211 209 204 209 214 116 107 107 105 105 105 ± 3.3 ±5 ±9 ± 12 ± 15 ± 24 ± 3.3 ±5 ±9 ± 12 ± 15 ± 24 ± 3.3 ±5 ±9 ± 12 ± 15 ± 24 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ± 600 ± 400 ± 220 ± 166 ± 133 ± 83 ± 600 ± 400 ± 220 ± 166 ± 133 ± 83 ± 600 ± 400 ± 220 ± 166 ± 133 ± 83 73 78 80 80 80 79 73 79 80 82 80 78 72 78 78 80 80 80 ± 680 ± 470 ± 220 ± 100 ± 47 ± 22 ± 680 ± 470 ± 220 ± 100 ± 47 ± 22 ± 680 ± 470 ± 220 ± 100 ± 47 ± 22 If you need other specifications, please enquire. * For optional 3.5kV DC I/O Isolation, please add “H35” before MLF! Example: P18TG-1205Z2:1H35MLF for 3.5kV PMD-Series – P18TG-xxxxE/Z2:1(H35)MLF – Single and Dual Output – DIP24 - Metal Case Specification can change without a notice – We accept no liability for any inaccuracy or printing errors. Page 2/3 Package / Pinning / Derating 27.94 (1.10) 1 All dimensions are typical in millimeters (inches). - Pin diameter: 0.5 +/-0.05 (0.02 +/-0.002) - Pin pitch tolerance: +/-0.35 (+/-0.014) - Case tolerance +/-0.5 (+/-0.02) Standard Drawing For exact pinning please see connection table! Specification may change without notice. 12 Bottom View 24 13 2.54 (0.10) DIP24 – METAL CASE 2.00 (0.08) 10.16 (0.40) PEAK Modelcode Datecode 31.75 (1.25) 3.05 (0.12) PIN CONNECTIONS # SINGLE DUAL 2 - Vin - Vin 3 - Vin - Vin 9 Omitted Common 11 N.C. - Vout 14 +Vout +Vout 16 - Vout Common 22 +Vin +Vin 23 +Vin +Vin others Omitted Omitted Same Pinning for 3.5kV Isolation App Notes: ¹ = Measured Input reflected ripple current with a simulated source inductance of 12uH. ² = Tested by nominal Vin and constant resistor load. PMD-Series – P18TG-xxxxE/Z2:1(H35)MLF – Single and Dual Output – DIP24 - Metal Case Specification can change without a notice – We accept no liability for any inaccuracy or printing errors. Page 3/3