P26TG-xxxxE/Z2:1(H35)MLF PMD-SERIES Rev.11-2008 6 Watt Regulated SINGLE and DUAL Output 1.5 to 3.5 kV DC I/O Isolation DIP24 Metal Case Continuous Short Circuit Prot. Full SMD Technology Mainzer Straße 151–153 D-55299 Nackenheim Tel. +49 6135 7026-0 Fax: +49 6135 931070 www.peak-electronics.de [email protected] The PMD 6W series P26TG-xxxxE/Z2:1(H35)MLF is a family of cost effective 6W single & dual output DC-DC converters. These converters are encapsulated in miniature DIP24 metal case. High performance features: 1500VDC up to 3500VDC input/output isolation, continuous short circuit protection with automatic restart and tight line / load regulation, high efficiency operation, output voltage accuracy of ±1% maximum. and a wide input of 2:1 All specifications typical at Ta=25°C, nominal input voltage and full load unless otherwise specified Input Specifications Voltage Range Input Filter Input Reflected Ripple Current¹ 2:1 Wide Input Pi Type 35 mA pk-pk Output Specifications Voltage Accuracy Short Circuit Protection Line Regulation Load Regulation Ripple and Noise (20Mhz bandwidth) Temperature Coefficient ± 1% Indefinite (automatic recovery) ± 0.5% ± 0.5% (3.3 / ± 3.3Vout Models: ± 1.5%) 60 mV pk-pk ± 0.02% / °C General Specifications Efficiency I/O Isolation Voltage (3 sec.) I/O Isolation Capacity I/O Isolation Resistance Switching Frequency (typical) Humidity Reliability Calculated MTBF (MIL-HDBK-217F) See Table 1500 VDC (3500 VDC optional)* 470 pF, typ. 1000 MOhm 266 kHz 95% rel H > 1.121 Mhrs Physical Specifications Case Material Potting Material Weight Nickel Coated Copper Epoxy (UL94V-0 rated) ~ 17g, typ. Environment Specifications Operating Temperature Maximum Case Temperature Storage Temperature Cooling RoHS Conform -40 to +85°C (ambient) 100°C -40 to +125°C Free Air Convection Soldering 260°C, max. (1.5mm from case 10s.) PMD-Series – P26TG-xxxxE/Z2:1(H35)MLF – Single and Dual Output – DIP24 - Metal Case Specification can change without a notice – We accept no liability for any inaccuracy or printing errors. Page 1/3 Selection Guide Single/Dual Output ) ) m A) mA) ad ( (mA ad (mA ad ( o ) o d L L a C o . ll L D n F²) Lo t Fu t Mi d (u ( e (V F ull No n n ) a g t t e e e o a n n r r % g t r r ( L l e e r y rr rr lta Cu Cu Vo ie nc t Cu put Cu t Vo acito put pu t put Inpu Inpu In Out Out Out Effic Cap ) VD C Order # SINGLE OUTPUT P26TG-123R3E2:1MLF P26TG-1205E2:1MLF P26TG-1209E2:1MLF P26TG-1212E2:1MLF P26TG-1215E2:1MLF P26TG-1224E2:1MLF P26TG-243R3E2:1MLF P26TG-2405E2:1MLF P26TG-2409E2:1MLF P26TG-2412E2:1MLF P26TG-2415E2:1MLF P26TG-2424E2:1MLF P26TG-483R3E2:1MLF P26TG-4805E2:1MLF P26TG-4809E2:1MLF P26TG-4812E2:1MLF P26TG-4815E2:1MLF P26TG-4824E2:1MLF 9-18 9-18 9-18 9-18 9-18 9-18 18-36 18-36 18-36 18-36 18-36 18-36 36-72 36-72 36-72 36-72 36-72 36-72 30 30 30 30 30 30 20 20 20 20 20 20 12 12 12 12 12 12 527 649 641 617 625 625 256 313 304 313 304 305 128 156 152 156 151 151 3.3 5 9 12 15 24 3.3 5 9 12 15 24 3.3 5 9 12 15 24 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1400 1200 666 500 400 250 1400 1200 666 500 400 250 1400 1200 666 500 400 250 73 77 78 81 80 80 75 80 82 80 82 82 75 80 82 80 83 83 1000 1000 680 330 220 68 1000 1000 680 330 220 68 1000 1000 680 330 220 68 DUAL OUTPUT P26TG-123R3Z2:1MLF P26TG-1205Z2:1MLF P26TG-1209Z2:1MLF P26TG-1212Z2:1MLF P26TG-1215Z2:1MLF P26TG-1224Z2:1MLF P26TG-243R3Z2:1MLF P26TG-2405Z2:1MLF P26TG-2409Z2:1MLF P26TG-2412Z2:1MLF P26TG-2415Z2:1MLF P26TG-2424Z2:1MLF P26TG-483R3Z2:1MLF P26TG-4805Z2:1MLF P26TG-4809Z2:1MLF P26TG-4812Z2:1MLF P26TG-4815Z2:1MLF P26TG-4824Z2:1MLF 9-18 9-18 9-18 9-18 9-18 9-18 18-36 18-36 18-36 18-36 18-36 18-36 36-72 36-72 36-72 36-72 36-72 36-72 30 30 30 30 30 30 20 20 20 20 20 20 12 12 12 12 12 12 527 649 625 625 632 625 333 321 301 312 312 312 171 158 158 156 156 156 ± 3.3 ±5 ±9 ± 12 ± 15 ± 24 ± 3.3 ±5 ±9 ± 12 ± 15 ± 24 ± 3.3 ±5 ±9 ± 12 ± 15 ± 24 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ± 909 ± 600 ± 333 ± 250 ± 200 ± 125 ± 909 ± 600 ± 333 ± 250 ± 200 ± 125 ± 909 ± 600 ± 333 ± 250 ± 200 ± 125 73 77 80 80 79 80 75 78 83 80 80 80 73 79 79 80 80 80 ± 680 ± 330 ± 220 ± 100 ± 47 ± 33 ± 680 ± 330 ± 220 ± 100 ± 47 ± 33 ± 680 ± 330 ± 220 ± 100 ± 47 ± 33 If you need other specifications, please enquire. * For optional 3.5kV DC I/O Isolation, please add “H35” before MLF! Example: P26TG-1205Z2:1H35MLF for 3.5kV PMD-Series – P26TG-xxxxE/Z2:1(H35)MLF – Single and Dual Output – DIP24 - Metal Case Specification can change without a notice – We accept no liability for any inaccuracy or printing errors. Page 2/3 Package / Pinning / Derating 27.94 (1.10) 1 All dimensions are typical in millimeters (inches). - Pin diameter: 0.5 +/-0.05 (0.02 +/-0.002) - Pin pitch tolerance: +/-0.35 (+/-0.014) - Case tolerance +/-0.5 (+/-0.02) Standard Drawing For exact pinning please see connection table! Specification may change without notice. 12 Bottom View 24 13 2.54 (0.10) DIP24 – METAL CASE 2.00 (0.08) 10.16 (0.40) PEAK Modelcode Datecode 31.75 (1.25) 3.05 (0.12) PIN CONNECTIONS # SINGLE DUAL 2 - Vin - Vin 3 - Vin - Vin 9 Omitted Common 11 N.C. - Vout 14 +Vout +Vout 16 - Vout Common 22 +Vin +Vin 23 +Vin +Vin others Omitted Omitted Same Pinning for 3.5kV Isolation App Notes: ¹ = Measured Input reflected ripple current with a simulated source inductance of 12uH. ² = Tested by nominal Vin and constant resistor load. PMD-Series – P26TG-xxxxE/Z2:1(H35)MLF – Single and Dual Output – DIP24 - Metal Case Specification can change without a notice – We accept no liability for any inaccuracy or printing errors. Page 3/3