SSR01-SERIES DC-DC CONVERTER 3~5.5VDC AND 4.6~36VDC WIDE INPUT RANGE UP TO 15Watts FEATURES APPLICATIONS • SMALL SIZE AND LOW PROFILE : 0.60 X 0.37 X 0.29 INCH • ADJUSTABLE OUTPUT VLOTAGE • LOW OUTPUT RIPPLE AND NOISE • NEGATIVE OUTPUT APPLICATION • UL60950-1, EN60950-1, & IEC60950-1 SAFETY APPROVALS • CE MARKED • COMPLIANT TO RoHS II & REACH NON ISOLATION REMOTE CONTROL OCP SCP • WIRELESS NETWORK • TELECOM/DATACOM • INDUSTRY CONTROL SYSTEM • DISTRIBUTED POWER ARCHITECTURES • SEMICONDUCTOR EQUIPMENT • MICROPROCESSOR POWER APPLICATIONS OTP LOW STANDBY POWER TECHNICAL SPECIFICATION All specifications are typical at nominal input, full load and 25℃ otherwise noted POSITIVE OUTPUT APPLICATION Model Number SSR01-05S2P5 SSR01-12S3P3 SSR01-12S05 SSR01-12S09 SSR01-24S12 SSR01-24S15 Nominal Input Input Range Frequency Nominal Output Output Voltage Trim Range (1) VDC 5 12 12 12 24 24 VDC 3.0 ~ 5.5 4.6 ~ 36 6.5 ~ 36 10.5 ~ 36 13.5 ~ 36 16.5 ~ 36 kHz 410 300 580 580 580 580 VDC 2.5 3.3 5 9 12 15 VDC 1.2 ~ 3.63 1.5 ~ 5.5 2.5 ~ 8.0 4.5 ~ 12.6 4.5 ~ 13.5 4.5 ~ 15.5 Output Current @Min. @Full Load Load A A 0 1 Efficiency (2) Input Current @ No Load Min.Vin Max.Vin mA 6 1.5 3 4 4 4 % 95.5 87.5 91.5 94.5 95.0 95.5 % 95.0 80.0 83.5 89.0 91.0 92.5 NEGATIVE OUTPUT APPLICATION Model Number SSR01-12S3P3 SSR01-12S05 SSR01-12S09 SSR01-24S12 SSR01-24S15 Nominal Input Input Range Frequency Nominal Output Output Voltage Trim Range (1) VDC 12 12 12 12 12 VDC 4.6 ~ 32 4.6 ~ 31 7 ~ 27 7 ~ 24 7 ~ 21 kHz 300 580 580 580 580 VDC -3.3 -5 -9 -12 -15 VDC -1.5 ~ -5.5 -2.5 ~ -8.0 -4.5 ~ -12.6 -4.5 ~ -13.5 -4.5 ~ -15.5 Output Current @Min. @Full Load Load mA mA -600 -400 0 -300 -300 -200 Efficiency (2) Input Current @ No Load Min.Vin Max.Vin mA 3 3 7 7 10 % 74.0 80.0 85.0 84.5 85.5 % 77.5 78.5 82.0 86.0 84.0 PART NUMBER STRUCTURE POSITIVE OUTPUT SSR01 Series Name 1 12 Input Voltage (VDC) 05: 3.0 ~ 5.5 12: 4.6 ~ 36 6.5 ~ 36 10.5 ~ 36 24: 13.5 ~ 36 16.5 ~ 36 S Output Quantity S: Single 05 Output Voltage (VDC) 2P5: 2.5 3P3: 3.3 05: 5 09: 9 12: 12 15: 15 www.PDUKE.com 2015/4/20 SSR01 NEGATIVE OUTPUT SSR01 Series Name 12 Input Voltage (VDC) 12: 4.6 ~ 32 4.6 ~ 31 7 ~ 27 24: 7 ~ 24 7 ~ 21 S Output Quantity S: Single 05 Output Voltage (VDC) 3P3: -3.3 05: -5 09: -9 12: -12 15: -15 C1 and C2 are required and should be fitted close to the converter pins. Maximum capacitive load including C2 is 470uF. C1 10uF / 50V 1210 X5R MLCC C2 10uF / 25V 1206 X5R MLCC INPUT SPECIFICATIONS Parameter Conditions Vin>Vout(set)+0.5V Vin>Vout(set)+1.5V See table Vin+|Vout|≦36V Operating input voltage range for positive output (3) Operating input voltage range for negative output (3) Input reflected ripple current Maximum input current Input filter Unit 5.5 36 VDC 4.6 32 VDC mAp-p A 1 Capacitor type Conditions Ripple and noise 0% to 100% of Full Load 10% to 90% of Full Load Measured by 20MHz bandwidth Temperature coefficient Dynamic load response 50% load step change Over load protection Positive output Min. Typ. -2.0 -0.2 -0.6 -0.3 Vout = 1.2 ~ 8VDC Vout = 8.1 ~ 15.5VDC Max. Unit +2.0 +0.2 +0.6 +0.3 % % % 50 75 mVp-p -0.015 Peak deviation Recovery time SSR01-05S2P5 Others Short circuit protection Capacitor Load (4) Output voltage overshoot-startup FEATURE SPECIFICATIONS Parameter 2 Typ. 100 Voltage accuracy Line regulation Load regulation Remote ON/OFF Max. 3.0 4.6 Vin=Vin(min); Io=Io(max) OUTPUT SPECIFICATIONS Parameter Start up time Min. Conditions Nominal input and Constant resistive load Positive output : Referred to GND pin Negative output : Referred to –Vout pin Power up Remote ON/OFF Positive logic DC-DC ON DC-DC OFF Input current of Ctrl pin Remote off input current www.PDUKE.com +0.015 %/℃ 150 mV 250 µs 400 % 200 Continuous, automatics recovery 470 µF 1.0 % Min. -0.1 Typ. Max. Unit 5 5 Open or 2 ~ 5VDC Short or 0 ~ 0.8VDC 0.1 1.2 ms mA mA 2015/4/20 SSR01 GENERAL SPECIFICATIONS Parameter Conditions Min. Safety meets MIL-HDBK-217F, Full load ENVIRONMENTAL SPECIFICATIONS Parameter Operating temperature range Maximum case temperature Over temperature protection Storage temperature range Lead-free reflow solder process Moisture sensitivity level(MSL) Thermal shock Vibration Relative humidity Max. Unit UL60950-1 EN60950-1 IEC60950-1 Non-conductive black plastic Non-conductive black plastic Epoxy (UL94 V-0) 1.7g(0.060oz) 1.457 x 107 hrs Case material Base materia Potting material Weight MTBF Typ. Conditions Min. With derating Typ. -40 Internal IC junction Max. Unit +105 105 170 -55 Non-condensing +125 IPC J-STD-020D IPC J-STD-033B Level 1 MIL-STD-810F MIL-STD-810F 0% to 90% RH Note: 1. 2. 3. 4. Output trimming: Model Number Vout,nom SSR01-05S2P5 SSR01-12S3P3 Trim up RU(kΩ) Trim down RD(kΩ) Model Number Vout,nom ︱±2.5V︱ SSR01-12S09 ︱±9.0V︱ ︱±3.3V︱ SSR01-24S12 ︱±12.0V︱ Trim up RU(kΩ) Trim down RD(kΩ) Typical value at min. or max. input voltage and full load. The input voltage can be increased to 42VDC by external capacitors. 3.1For Positive output: Input capacitor is necessary when input voltage 36VDC increased to 42VDC. The input capacitor suggestion is 22uF. 3.2For Negative output application: The input and output capacitors are necessary for negative output application when the 36VDC beincreased to 42VDC, and the suggestion of capacitors: The C1 is 22uF and the C2 is 10uF. (Please refer to the figure of positive to negative output application) Consider to the maximum duty of internal controller. In the trim down application,these are some condition that input range can’t increase to 42VDC. Model Number Output voltage(Trim down) Input range SSR01-12S09 -4.5 ~ -6VDC Vin + |Vout| ≦ 36VDC SSR01-24S12 -4.5 ~ -6VDC Vin + |Vout| ≦ 36VDC SSR01-24S15 -4.5 ~ -6VDC Vin + |Vout| ≦ 36VDC Test by minimum input and constant resistive load. CAUTION: This power module is not internally fused. An input line fuse must always be used. 3 www.PDUKE.com 2015/4/20 SSR01 CHARACTERISTIC CURVE POSITIVE OUTPUT SSR01-12S05 Derating Curve SSR01-12S05 Efficiency vs. Input Voltage SSR01-12S05 Efficiency vs. Output Load NEGATIVE OUTPUT SSR01-12S05 Derating Curve SSR01-12S05 Efficiency VS Input Voltage SSR01-12S05 Efficiency VS Output Load MECHANICAL DRAWING FOR STARDANDS PIN CONNECTION PIN SINGLE 1 +Vin 5 +Vout 6 Trim 7 GND 9 GND 10 Ctrl EXTERNAL OUTPUT TRIMMING Output can be externally trimmed by using the method shown below. TRIM UP 6 TRIM DOWN 5 RU 7，9 RD 6 1. All dimensions in inch (mm) 2. Tolerance :x.xx±0.02 (x.x±0.5) x.xxx±0.01 (x.xx±0.25) 3. Pin pitch tolerance ±0.01 (0.25) 4. Pin dimension tolerance ±0.004(0.1) 4 www.PDUKE.com 2015/4/20