FDC15 FDC15 SERIES DC-DC CONVERTER 4 : 1 ULTRA WIDE INPUT RANGE UP TO 15Watts FEATURES APPLICATIONS • 1600VDC INPUT TO OUTPUT ISOLATION • STANDARD 2.00 X 1.60 X 0.40 INCH • SIX-SIDED CONTINUOUS SHIELD • UL60950-1, EN60950-1, & IEC60950-1 SAFETY APPROVALS • CE MARKED • COMPLIANT TO RoHS II & REACH 1600VDC ISOLATION REMOTE CONTROL OCP SCP • WIRELESS NETWORK • TELECOM/DATACOM • INDUSTRY CONTROL SYSTEM • DISTRIBUTED POWER ARCHITECTURES • SEMICONDUCTOR EQUIPMENT OVP TECHNICAL SPECIFICATION All specifications are typical at nominal input, full load and 25 Model Number FDC15-24S05 FDC15-24S12 FDC15-24S15 FDC15-24D05 FDC15-24D12 FDC15-24D15 FDC15-48S05 FDC15-48S12 FDC15-48S15 FDC15-48D05 FDC15-48D12 FDC15-48D15 Input Range Output Voltage VDC VDC 9 ~ 36 9 ~ 36 9 ~ 36 9 ~ 36 9 ~ 36 9 ~ 36 18 ~ 75 18 ~ 75 18 ~ 75 18 ~ 75 18 ~ 75 18 ~ 75 5 12 15 ±5 ±12 ±15 5 12 15 ±5 ±12 ±15 Output Current @Full Load Min. Load (1) mA 210 100 80 ±105 ±50 ±40 210 100 80 ±105 ±50 ±40 otherwise noted Input Current @ No Load Efficiency Maximum Capacitor Load (2) mA % µF 20 10 20 20 20 20 15 15 10 10 20 15 80 82 82 80 82 82 80 82 82 80 82 82 Full Load mA 3000 1250 1000 ±1500 ±625 ±500 3000 1250 1000 ±1500 ±625 ±500 6800 890 570 ±1700 ±300 ±200 6800 890 570 ±1700 ±300 ±200 PART NUMBER STRUCTURE FDC15 - 48 Series Name Input Voltage (VDC) 24: 9~36 48: 18~75 S Output Quantity S: Single D: Dual 05 Output Voltage (VDC) 05: 5 12: 12 15: 15 05: ±5 12: ±12 15: ±15 INPUT SPECIFICATIONS Parameter HS Assembly Option : No assembly HS: Heat-sink HC: Heat-sink with Clamp Conditions Operating input voltage range 24Vin(nom) 48Vin(nom) Input reflected ripple current Start up time Input surge voltage Nominal input and Full load Constant resistive load 100 ms, max. Input filter Remote ON/OFF Referred to –Vin pin 1 - Min. Typ. Max. Unit 9 18 24 48 20 20 36 75 VDC Power up 24Vin(nom) 48Vin(nom) Positive logic DC-DC ON DC-DC OFF Input current of Ctrl pin Remote off input current www.PDUKE.com -0.5 mAp-p ms 50 VDC 100 Pi type Open or 3.5 ~ 12VDC Short or 0 ~ 1.2VDC +0.5 mA 20 mA 2015/2/26 FDC15 OUTPUT SPECIFICATIONS Parameter Voltage accuracy Line regulation Load regulation Cross regulation Voltage adjustability Ripple and noise Temperature coefficient Transient response recovery time Over voltage protection Over load protection Short circuit protection Conditions Low Line to High Line at Full Load Min. Load to Full Load Asymmetrical load 25%/100% FL Single Dual Dual 25% load step change Zener diode clamp Isolation resistance Isolation capacitance Switching frequency Safety approvals 500VDC 5Vout 12Vout 15Vout % % +0.02 % % mVp-p %/ µs VDC Conditions Min. Input to Output Input(Output) to Case 1600 1600 1 MIL-HDBK-217F, Full load Conditions Min. With derating Typ. Without heat-sink With heat-sink Unit VDC GΩ pF 270 kHz UL60950-1 EN60950-1 IEC60950-1 Nickel-coated copper Non-conductive black plastic Epoxy (UL94 V-0) 48g (1.69oz) 2.250 x 106 hrs 300 297 Typ. -40 Max. Unit +85 +100 +125 -55 Vertical direction by natural convection (20LFM) Max. 10 8.24 /W Thermal shock Vibration Relative humidity MIL-STD-810F MIL-STD-810F 5% to 95% RH EMC SPECIFICATIONS Parameter EMI ESD Radiated immunity Fast transient (3) Surge (3) Conducted immunity % 150 % Continuous, automatics recovery 243 ENVIRONMENTAL SPECIFICATIONS Parameter Unit +1.0 +0.2 +0.5 +1.0 +5.0 +10 250 6.2 15 18 % of Iout rated 1 minute Max. 75 -0.02 Isolation voltage Operating ambient temperature Maximum case temperature Storage temperature range Thermal impedance Typ. -1.0 -0.2 -0.5 -1.0 -5.0 -10 Measured by 20MHz bandwidth GENERAL SPECIFICATIONS Parameter Case material Base material Potting material Weight MTBF Min. Conditions EN55022 EN61000-4-2 EN61000-4-3 EN61000-4-4 EN61000-4-5 EN61000-4-6 Air ± 8kV and Contact ± 6kV 10 V/m ± 2kV ± 1kV 10 Vr.m.s Level Class A, Class B Perf. Criteria B Perf. Criteria A Perf. Criteria B Perf. Criteria B Perf. Criteria A Note: 1. 2. 3. The output requires a minimum loading on the output to maintain specified regulation. Operation under no-load condition will not damage these devices, however they may not meet all listed specification. Test by minimum input and constant resistive load. An external input filter capacitor is required if the module has to meet EN61000-4-4, EN61000-4-5. The filter capacitor Power Mate suggest: Nippon chemi-con KY series, 220µF/100V. CAUTION: This power module is not internally fused. An input line fuse must always be used. 2 www.PDUKE.com 2015/2/26 FDC15 CHARACTERISTIC CURVE FDC15-48S05 Derating Curve FDC15-48S05 Derating Curve With Heat-sink FDC15-48S05 Efficiency vs. Input Voltage FDC15-48S05 Efficiency vs. Output Load MECHANICAL DRAWING PIN CONNECTION PIN 1 2 4 5 6 7 8 SINGLE +Vin -Vin Ctrl No pin +Vout -Vout Trim DUAL +Vin -Vin Ctrl +Vout Common -Vout Trim EXTERNAL OUTPUT TRIMMING Output can be externally trimmed by using the method shown below. ( ) for dual output trim. TRIM UP 7(7) TRIM DOWN 8(8) RU 8(8) RD 6(5) 1. All dimensions in inch (mm) 2. Tolerance :x.xx±0.02 (x.x±0.5) x.xxx±0.01 (x.xx±0.25) 3. Pin pitch tolerance ±0.01 (0.25) 4. Pin dimension tolerance ±0.004(0.1) 3 www.PDUKE.com 2015/2/26